考虑预载固结效应的海底浅基础承载力包络面演化规律研究

由于预载下土体固结,海底浅基础的承载力会随作业时间的增加而改变,其时变效应评估困难。基于修正剑桥模型,采用水土耦合有限元方法研究了预载作用下浅基础在正常固结黏土海床中承载力破坏包络面的时变规律。在验证数值模型准确性后,通过位移探针测试获取复合加载模式下浅基础的破坏包络面,揭示了预载和固结程度对基础承载力和破坏包络面的影响,给出了预载作用下浅基础承载力包络面计算方法。结果表明：随着预载比增加,固结单轴承载力呈现线性增长,固结承载力增幅在水平向最大;部分固结承载力相对增幅与预载比无关,而随固结度变化;破坏包络面形状由预载比控制,而包络面大小由预载比和固结度共同控制。研究结果可为海洋浅基础的时变承载力评估提供参考依据。     

在软质海底上负压沉箱的动力响应特性

通过对沉箱结构在波浪作用下动力响应的模拟研究,探讨了一种有裙钢质沉箱的适用性,这种沉箱可利用负压效应来保持它自身的稳定。对于这种在沉箱底部和海底之间具有负压作用的沉箱,采用了“沉箱结构与海底相互作用分析法”在频率域中进行了动力响应数值计算。文中假定沉箱结构的分析模型是一个带有裙边的刚性棱柱体,在其底部设有若干个正方形的隔室（compartment）,负压就作用在每个隔室上;此外,还假定海底是一种液体饱和的多孔弹性体,其特性符合blot的波浪传播理论。沉箱裙边的长度以及作用在隔室上的负压对于沉箱动力响应的影响,也通过数值计算的方法进行了研究。其结论是：这种类型的沉箱应用于软质海底是相当有效的。如果海底上的渗透性差,只要为沉箱提供隔室,则它也会具有同样的优点。     

复合加载条件下吸力式沉箱基础承载特性数值分析

吸力式沉箱基础的承载特性是海洋工程结构设施建造与设计中的一个关键问题。这种新型的深水海洋基础型式,通常承受竖向上拔荷载与水平荷载的共同作用,其工作性能与设计理论远远不能满足工程实践的需要。本文采用有限元分析方法对吸力式沉箱基础的极限承载特性进行数值计算。以大型通用有限元分析软件ABAQUS为平台,通过二次开发,数值实现了Swipe试验加载方法和固定位移比分析方法,针对不同的沉箱长径比、土的强度折减系数,探讨了沉箱基础在垂直上拔荷载和水平荷载单调联合作用下的极限承载力,通过对不同荷载组合的数值计算构造了复合加载条件下沉箱基础破坏包络面。     

吸力式沉箱基础长期水平荷载作用下承载特性试验研究

通过两组不同水平荷载作用下吸力式沉箱基础长期模型试验,对吸力式沉箱基础随时间的位移变化规律以及土压力分布规律进行了研究。试验结果表明:在长期模型试验中位移发展主要集中在试验前期,后期位移稳定需要更长时间,土体流变效应较为明显。土压力沿深度分布曲线呈抛物形状,表明沉箱基础在水平荷载作用下为转动模式,随时间增加被动区土压力变化呈增大趋势,主动区土压力呈减小趋势。土压力发展主要集中在试验前期,后期土压力变化相对较小,但土压力稳定所需时间较长,同时荷载值越大土压力稳定所需时间越长。     

初始几何缺陷对管道极限承载力影响研究

初始几何缺陷被认为是影响管道极限承载力和稳定性的重要因素,但是大部分的管道力学特性研究都没有考虑初始缺陷的影响。基于管道几何尺寸测量机,获得管道的壁厚和直径沿轴向以及环向的分布规律。据此建立了四个三维实体有限元模型,分别为完好管道模型、只考虑直径缺陷的管道模型、只考虑壁厚缺陷的管道模型以及考虑所有缺陷的管道模型。分析了初始缺陷对管道的极限内压承载力、极限轴力承载力和极限弯矩承载力的影响。结果表明,直径缺陷对管道的极限内压承载力影响较大;壁厚缺陷对管道在复杂荷载作用下的极限弯矩承载力影响较大。     

筒型基础竖向极限承载力分析

结合最新研究成果,编制了筒型基础竖向极限承载力计算程序,可根据土壤参数和承载能力要求确定筒型基础的主要尺寸;同时使用ABAQUS和ANSYS软件建立筒型基础有限元模型,采用非线性接触方法模拟筒-土的边界,计算筒型基础的竖向极限承载力,两种软件的计算结果和编制程序的计算结果基本相同;最后对影响筒型基础竖向极限承载力的土壤...     

考虑冲刷影响的筒型基础竖向极限承载力研究

大直径宽浅式筒型基础,阻水宽度大,在位工作期间受波浪海流作用,其周围土体易被冲刷。为研究单侧地基土体受冲刷后筒型基础的竖向极限承载力变化,通过引进冲刷率的概念,采用有限元方法研究了不同冲刷率下筒型基础的竖向极限承载力;并基于Meyerhof理论建立了计算不同冲刷率下筒型基础竖向极限承载力的极限平衡方法。研究结果表明,随着冲刷率增大,筒型基础的极限承载力出现不同程度的下降,当冲刷率为0.8时,即筒型基础单侧土体冲刷深度达6.4 m时,筒型基础的竖向极限承载力折减率为3.28%。建立的极限平衡算法可准确计算冲刷条件下筒型基础的竖向极限承载力。     

沉箱基础对摇板式波浪能装置水动力性能影响研究

摇板式波浪能转换装置具有频率响应范围广、可靠性好、常规海况下转换效率高、建造成本低等优点。基于势流理论建立具有沉箱基础的摇板式波浪能装置水动力性能的解析解。将解析结果与文献中已有结果和边界元数值结果进行了对比,验证了解析解求解过程的正确性。通过算例分析,研究了波浪入射频率、沉箱基础高度、沉箱基础宽度、摇板位置、摇板厚度和摇板密度对装置能量俘获效率的影响。研究结果表明：采用合适高度的沉箱基础能显著提升装置性能;长波海况下,摇板铰接在沉箱基础背浪侧上表面时装置性能更佳,而短波海况下,摇板铰接在沉箱基础迎浪侧上表面更为合理;沉箱基础宽度的推荐值为0.5到1.0倍水深;适当减小摇板厚度能够提升装置性能;应优先选用密度较大的摇板。     

梳式沉箱翼缘板设计理论的研究

结合模型试验 ,分析了梳式沉箱翼缘板的静力和自振特性。研究了三种不同支承形式的翼缘板在最不利荷载下的内力分布 ,为梳式沉箱翼缘板的设计提供了依据     

复合加载下桶形基础循环承载性能数值分析

作为一种新型基础形式,吸力式桶形基础除了承受海洋平台结构及自身重量等竖向荷载的长期作用之外,往往还遭受波浪等所产生的水平荷载及其力矩等其它荷载分量的瞬时或循环作用。对复合加载模式下软土地基中桶形基础及其结构的循环承载性能尚缺乏合理的分析与计算方法。应用Andersen等对重力式平台基础及地基所建议的分析方法,基于软黏土的循环强度概念,在大型通用有限元分析软件ABAQUS平台上,通过二次开发,将软土的循环强度与Mises屈服准则结合,针对吸力式桶形基础,基于拟静力分析建立了复合加载模式下循环承载性能的计算模型,并与复合加载作用下极限承载性能进行了对比。由此表明,与极限承载力相比,桶形基础的循环承载力显著降低。     

水平荷载作用下裙式吸力基础承载性能研究

传统吸力基础是一个单桶结构,被广泛作为海洋平台、漂浮结构的基础,近年来也被推广到海上风电塔架。作为风电塔架基础,要充分提高其水平承载能力。为此,提出一种改进的基础形式—裙式吸力基础。采用Z_SOIL有限元软件,针对砂土地基,从水平单调加载和循环加载两个方面,对传统单桶吸力基础和裙式吸力基础进行了承载性能对比研究,得到了相应的荷载-位移曲线。研究结果表明,裙式吸力基础由于设置了"裙"结构,显著提高了其抵抗水平静载和循环水平动力荷载的能力,并能有效控制基础的水平位移,是值得推广应用的一种新型海洋工程基础形式。     

Model tests on performance of offshore wind turbine with suction caisson foundation in sand

Abstract

The performance of steel caisson during and after installation with different penetration velocities in medium dense sand is presented. The applied jacking forces, the amount of formed soil heave and bearing capacity were measured in the model tests. The influence of penetration velocities on jacking forces, soil heave and bearing capacity were also discussed in detail. The results indicated that the jacking forces for caisson in medium dense sands were significantly affected by the penetration velocity. The larger the penetration velocity, the more soil flowed into the caisson cavity during installation. This will lead to larger inner shaft resistance and in turn more jacking forces required for the same penetration depth. The height of soil heave during installation increases with penetration velocity. The m value calculated by the ratio of the volumes of the soil heave to that of the penetrated caisson wall can be used to evaluate the soil heave. The larger the applied velocity, the larger the m value and larger bearing capacity of caisson after installation. The relationship between the m value and penetration velocity can be used to control the soil heave for a steel caisson with a wall thickness to external diameter ratio of 4.2% in medium dense sand by jacking method.     

海上风机吸力基础的水平受荷研究综述

吸力基础具有施工速度快、安装过程中受海况天气影响小且易于回收重复利用等优点,被广泛应用于海洋工程。当吸力基础作为海上风电塔架的基础时,常常承受较大的水平荷载,因此其水平承载力是设计的主控因素。介绍了海上风机基础的设计要求,分析了影响基础水平承载性状的因素,总结了吸力基础受水平单调荷载、水平循环荷载和不同荷载组合三个方面的研究现状。讨论了水平荷载的大小、水平加载的高度(偏心率)、循环荷载的频率、循环荷载的次数、循环荷载的幅值、循环荷载的方向性、竖向荷载对吸力基础水平承载性状的影响,考虑了水平荷载的非共线性,指出了目前研究的不足,明确了吸力基础水平承载性状进一步研究的方向,提出了供工程实践参考的建议。     

Response and capacity of monopod caisson foundation under eccentric lateral loads

Monopod caisson foundation is a viable alternative for supporting offshore wind turbines located at shallow water depths. This foundation system has to resist overturning moment generated due to resultant lateral load, arising from wind and water wave action, that can act at any loading height above the seabed. This paper presents results of a numerical investigation performed to determine the influence of loading height, caisson geometry and superstructure load on the ultimate lateral capacity, initial stiffness, and soil failure zone of the foundation, when installed in very dense sand. Both the ultimate and serviceable states of the caisson foundation obtained from the analyses are represented in terms of envelopes plotted between lateral load and overturning moment. Simplified expressions, which take into account the influence of caisson geometry, loading height, and soil properties, are also presented to serve as a preliminary base for design of the monopod caisson foundation.     

Finite Element Analysis of Laterally Loaded Suction Caisson in Anisotropic Clay

1 .IntroductionSuctioncaissons have been widely usedfor offshore oil exploration duetothe advantages of econo-my and simple installation over traditional piles (Huanget al .,2003) .For tensionleg platforms andspar platforms in deep ocean,suction caissons …     

Investigation of scour effects on lateral behaviors of suction caisson

ABSTRACT

The use of suction caissons can reduce the development costs of offshore wind energy and has broad application prospects. However scour around marine foundations is inevitable, it gravely affects the stability of marine engineering. Therefore, there is an urgent need to study the weakening effects of scour on suction caisson. In this study, the variation trends of remaining soil parameters (the effective unit weight and the peak effective friction angle) after scour are examined with consideration of the dilatancy and stress history of sandy silt. It is found that the parameters of shallow soil change considerably after scour, and the larger the scour depth, the greater is the change in the parameters. However, the deep soil is less affected. On the basis of these findings, scour effects on the ultimate moment capacity of suction caisson are studied. The ultimate moment capacity is found to greatly reduce under scour, and its calculated value is larger than the actual value when the effects of dilatancy and stress history are ignored. To simplify calculation, it is feasible to replace the ultimate moment capacity when both dilatancy and stress history are considered with that when only dilatancy is considered.     

Failure Loci of Suction Caisson Foundations Under Combined Loading Conditions

Suction caissons are widely used to support offshore fixed platforms in coastal areas. The loadings transferred to suction caissons include the eccentric lateral force induced by waves and self weight of the platform structure. However, under this kind of combined loading conditions, the failure mechanism of caissons with shallow embedment depths is quite different from conventional deep foundations or onshore shallow footings. The behaviour of caissons subjected to combined loadings may be described with the "failure locus" in force resultant spaces. Here the failure loci of smooth caissons are studied by use of finite element approach, with the embedment ratio of caissons varying in the range of 0.25～1.0 and eccentricity ratio of horizontal loadings in 0～10. The platform settlement and tilt limits are involved into determination of failure loci, thus the platforms can avoid significant displacements for the combined loadings located inside the failure locus. Three families of loading paths are used to map out the locus. It is found that the shape of failure loci depends on 3 non-dimensional parameters, and the failure locus of a given caisson changes gradually from the elliptical curve to hooked curve with increasing shear strength of soil. The lateral capacity of short caissons may be enhanced by vertical forces, compared with the maximum lateral capacity of long caissons occurring at the vertical force being zero. The critical embedment ratios partitioning elliptical and hooked loci are proposed.     

Two-Dimensional Large Deformation Finite Element Analysis for the Pulling-up of Plate Anchor

Based on mesh regeneration and stress interpolation from an old mesh to a new one, a large deformation finite element model is developed for the study of the behaviour of circular plate anchors subjected to uplift loading. For the deterruination of the distributions of stress components across a clay foundation, the Recovery by Equilibrium in Patches is extended to plastic analyses. ABAQUS, a commercial finite element package, is customized and linked into our program so as to keep automatic and efficient running of large deformation calculation. The quality of stress interpolation is testified by evaluations of Tresca stress and nodal reaction forces. The complete pulling-up processes of plate anchors buried in homogeneous clay arc simulated, and typical pulling force-displacement responses of a deep anchor and a shallow anchor are compared. Different from the results of previous studies, large deformation analysis is of the capability of estimating the breakaway between the anchor bottom and soils. For deep anchors, the variation of mobilized uplift resistance with anchor settlement is composed of three stages, and the initial buried depths of anchors affect the separation embedment slightly. The uplift bearing capacity of deep anchors is usually higher than that of shallow anchors.