低围压水平下砂的排水行为(英文)

采用干样沉降法制备样品 ,选用静三轴仪对松砂和密砂样在 10 k Pa至 10 0 k Pa的低围压下的排水行为进行了实验研究 ,并对实验结果作了橡皮膜校正 ,在围压为 10 k Pa的密砂实验中 ,轴向应力的校正值可达到 12 %。实验研究表明低围压下松砂的剪胀性非常明显 ,且存在剪应力极值 ;围压越低 ,松砂和密砂的剪应力极值越小 ,达到最大剪应力所对应的剪应变越小。同时还表明低围压范围内相对密度不同 ,砂的应力应变特性不同 ;此外 ,低围压下砂的内摩擦角高于高围压下的值 ,从而在工程上应重视低围压水平下砂土工程参数的合理选取     

Research on Measurement of Bed Shear Stress Under Wave-Current Interaction

The movement of sediment in estuary and on coast is directly restricted by the bed shear stress. Therefore, the research on the basic problem of sediment movement by the bed shear stress is an important way to research the theory of sediment movement. However, there is not a measuring and computing method to measure the bed shear stress under a complicated dynamic effect like wave and current. This paper describes the measurement and test research on the bed shear stress in a long launder of direct current by the new instrument named thermal shearometer based on micro-nanotechnology. As shown by the research results, the thermal shearometer has a high response frequency and strong stability. The measured results can reflect the basic change of the bed shear stress under wave and wave?current effect, and confirm that the method of measuring bed shear stress under wave?current effect with thermal shearometer is feasible. Meanwhile, a preliminary method to compute the shear stress compounded by wave?current is put forward according to the tested and measured results, and then a reference for further study on the basic theory of sediment movement under a complicated dynamic effect is provided.     

Research on Measurement of Bed Shear Stress Under Wave?Current Interaction

The movement of sediment in estuary and on coast is directly restricted by the bed shear stress. Therefore, the research on the basic problem of sediment movement by the bed shear stress is an important way to research the theory of sediment movement. However, there is not a measuring and computing method to measure the bed shear stress under a complicated dynamic effect like wave and current. This paper describes the measurement and test research on the bed shear stress in a long launder of direct current by the new instrument named thermal shearometer based on micro-nanotechnology. As shown by the research results, the thermal shearometer has a high response frequency and strong stability. The measured results can reflect the basic change of the bed shear stress under wave and wave?current effect, and confirm that the method of measuring bed shear stress under wave?current effect with thermal shearometer is feasible. Meanwhile, a preliminary method to compute the shear stress compounded by wave?current is put forward according to the tested and measured results, and then a reference for further study on the basic theory of sediment movement under a complicated dynamic effect is provided.     

Study on the shear property of nano-MgO-modified soil

To study the relationship between nano-MgO and soil shear property, the nano-MgO was evenly mixed in the soil to perform the triaxial consolidation draining shear test. Then the microscopic soil granules on the shear planes were observed through the scanning electron microscope. The soil water content was 10% and soil dry density was 1.5?g/cm³, different dosages of nano-MgO, i.e., 0, 2, 4, and 6% were put into the soil samples. The result of triaxial consolidation draining shear test showed that, under low confining pressure and more nano-MgO dosage, the stress–strain relationship of nano-MgO-modified soil turned from hardening to softening. The incorporation of nano-MgO can effectively improve the soil failure strength and cohesive force, and the increasing dosages of nano-MgO had a positive effect on soil shear strength and cohesive force, but little effect on internal friction angle. The analysis of scanning electron microscopy showed that the dosage of nano-MgO can reduce the void ratio of soil and reinforce the cementation between soil granules to change the shear property of soil.     

TGR-2050型自动验潮仪的使用

剖析了TGR-2050自动验潮仪的工作原理,分析了影响测量精度的各种误差因素,指出该仪器设计上的缺陷,并给出实例,介绍了进行大气压改正的方法,得出了有益结论。     

循环荷载作用下粉土的动力学特征

选用近海分布广泛的粉土为研究对象,利用动三轴压缩试验结果得到了动荷载作用下粉土的应力-应变关系、孔压发展模式及动强度与临界循环次数之间的关系;探讨固结围压和固结比对粉土动力学性质的影响。动力学试验结果表明,动剪切模量随着固结围压的增大而增大,动阻尼比随动剪应变幅的变化关系受围压影响不大;不同围压对动剪应力的比值影响很小,同一围压下随着固结比的增大,动剪应力比也会随之增大;不同围压及不同固结比对以Nf表示的峰值孔隙水压力发展模式影响很小。     

循环荷载下粉土液化流动特性拖球试验研究

基于流体力学中的Stokes黏滞阻力理论,以振动台试验为基础,开发了一套测量液化过程中粉土流变特性的拖球试验装置。在铺有粉土海床的模型箱内埋设光滑小球,通过测量小球水平运动过程中所受阻力值的大小,计算粉土液化的表观动力黏度,分析粉土液化过程中的表观动力黏度与超孔压比之间的关系,以及液化后表观黏度与应变率的变化规律。试验结果表明,振动台试验下,孔隙压力表现为迅速上升,粉土迅速达到液化状态;振动过程对海床固结影响较大;粉土海床在未达到完全液化状态时（ru<1）,表观黏度随超孔压比增大而减小,在液化状态下（ru=1）,剪应力随应变率增大而减小,粉土呈现出剪切稀化的特点,为典型的非牛顿流体特征。     

Implementation of state-dependent plasticity model in strain wedge model for laterally loaded piles in sand

ABSTRACT

The strain wedge model effectively performs nonlinear analyses of the lateral response of piles by using a nonlinear stress-strain relationship to describe soil behavior in the strain wedge. In this study, a state-dependent plasticity model has been implemented in the strain wedge model to calculate the stress-strain relationship for sand in the strain wedge. To complement this implementation, the effect of dilatancy on the shear strain is considered in the strain wedge. A full-scale test and a 45 g centrifuge model test on laterally loaded piles are used to validate the proposed method. The results show that the deflections and moments predicted by the proposed method accord well with those measured from full-scale and centrifugal model pile tests. Moreover, the combination of the state-dependent plasticity model and the strain wedge model allows for analyzing the lateral response of single piles using a unique set of model parameters for different relative densities of sands. In addtion, the stress-strain response in the strain wedge, not the dilatancy, dominates the soil resistance in the strain wedge and thus the lateral response of piles.     

Experimental study on the cyclic behavior of loose calcareous sand under linear stress paths

Abstract

Hollow cylinder torsional shear tests on loose isotropically and anisotropically consolidated calcareous sand were conducted to investigate the cyclic behavior under three different linear stress paths, including horizontal line, oblique line, and vertical line stress paths, in a coordinate system of the normal stress difference and the horizontal shear stress. The dominant strain components of the isotropically consolidated specimens are affected by the stress paths. With increasing consolidation stress ratio, axial strain gradually becomes the dominant strain component under the three different stress paths. The cyclic strength of the isotropically consolidated specimens under the three different stress paths are almost the same, while for the anisotropically consolidated specimens, the cyclic strengths are strongly affected by the stress paths. These results indicate that conventional cyclic triaxial tests may overestimate cyclic strength in some cases. Irrespective of the stress paths and cyclic stress ratios, the terminal residual excess pore pressure ratio decreases with increasing consolidation stress ratio. Moreover, an empirical equation is proposed to describe the relationship between the normalized shear work and the normalized residual excess pore pressure ratio. The comparative study reveals that the relationship proposed for silica sand is not suitable for the dynamic analyses of calcareous sand.     

海上不利工况下的导管架灌浆连接段黏结力试验研究

为解决海上风机导管架支腿和钢管桩灌浆段在海上恶劣施工与工作环境下发生偏心连接和偏心受力等不利工况时灌浆连接段的力学特性问题,文章制作海上风机导管架灌浆连接段足尺模型,对其黏结承载力进行原型抗拔试验,同时进行应变测试,以研究偏心灌浆等不利工况对灌浆连接段黏结承载力的影响。研究结果表明:导管架灌浆连接的轴向和偏心黏结承载力均满足设计要求;在轴向拉拔时,由于灌浆料受拉拔时其厚度越大则剪切变形越大,灌浆连接段各测点的位移由大到小依次为灌浆较厚侧、平均位移、灌浆较薄侧,但其应力差异不大;在偏心拉拔时,总上拔力虽减小,但偏心受力会导致结构弯矩和内力增加,表明在设计时应充分考虑偏心荷载对灌浆料的不利作用。     

Particle Flow Simulation on Collapse Characteristics of Silt Under Mutation of Principal Stress Orientation

The behaviors of granular material and influencing factors under complex dynamic loading are studied by more and more researchers with particle flow method. Only the strain-controlled loading has been generally used in the current study, although this method was not consistent with the practice of engineering in many situations. In this article, stress-controlled dynamic simulation tests were carried out with particle flow method, which were used to study the collapse characteristics of silt under mutation of principal stress orientation. The tests were performed by PFC2D. The simulation results and the laboratory real tests’ results had a high degree of similarity, particularly in the collapse strain and vibration times. It was very useful to forecast the silt's critical failure state. Based on the verification data, the effects of confining pressure and cyclic shear stress ratio on the collapse characteristics of silt were studied further. With the increase of cyclic shear stress ratio, the deviator strain amplitude increased and the required vibration times gradually reduced to achieve the same strain level. Under the same dynamic shear stress ratio and vibration times, the initial dynamic elastic modulus slightly increased with the increase of initial confining pressure, and the variation range of final collapse deviator strain was small. In the analysis of micro-structural evolution, the redistribution of internal stress of sample was revealed during cyclic loading. With the increase of vibration times, the development of distribution gradually stabilized, and then the high shear stress appeared in some connected regions. On that stage, the particle system developed to instability and failure. The PFC simulation results confirmed that the collapse state was the critical stage to trigger the liquefaction of silt.     

Effect of angle between initial and cyclic shear stress on behaviors of marine clay

An angle exists between the initial static shear stress and cyclic shear stress when embankment and retaining walls are subjected to cyclic loadings. To investigate the influence of this angle on the dynamic properties of marine soft clay, tests were performed on Wenzhou soft clay. When the angle was varied from 0° to 90°, the shear strain and excess pore pressure decreased as θ increased while increased as θ increased from 120° to 180°. Shear strain developed more rapidly when θ was 120°, 150°, or 180° than that when θ was 0°, 30°, or 60°. These results indicate that the number of cycles to failure at the larger angles was greater than at the smaller angles. When θ was 90°, the strain in the x-axis direction increased as the number of cycles increased. The development of the excess pore pressure associated with specimen failure was different for different cyclic shear stress ratios and shearing angles. The effect of θ on the strain and excess pore pressure increased as the cyclic shear stress ratio increased.     

Undrained strength behaviour of a cemented marine clay under monotonic and cyclic loading

The paper presents the results of a series of monotonic and cyclic triaxial shear tests carried out to study the influence of the strain effect and load cycles on the undrained shear strength of a cemented marine clay from the East coast of India. The undrained shear strength of Indian coastal marine clay has been established from a detailed shear testing carried out in three phases. Undisturbed soil samples taken out from the seabed were used in the test. In the first part, a comprehensive monotonic shear testing has been carried out under both stress-controlled and strain rate-controlled conditions. In the second phase on identical soil specimen, undrained cyclic shear tests were carried out at various cyclic stress ratios (CSR) and these stress levels are chosen in such a way so that no failure occurred during testing. In the final phase post cyclic monotonic shear testing was conducted to qualitatively evaluate the damage caused by cyclic loading. The monotonic shear test results bring out the influence of cementation that can be detected by the stress-controlled test. The cyclic stress results are analysed in terms of CSR. Further, the results are correlated in terms of stress path.     

Mechanical Behavior of Light-Weight Soil Under Consolidated Drained Shear Condition

To reveal the influence of material composition on mechanical properties of light-weight soil, stress-strain -volumetric strain characteristics and Poisson's ratio of mixed soil were researched by consolidated drained shear tests. The results show that light-weight soil is a kind of structural soil, so its mechanical properties are affected by mixed ratio and confining pressure, and mixed soil possesses structural yield stress. When confining pressure is less than the structural yield stress, strain softening occurs; when confining pressure is more than the structural yield stress, strain hardening is observed. There are two kinds of volume change behavior: shear contraction and shear dilatancy. Shear dilatancy usually leads to strain softening, but there isn't an assured causal relationship between them. Poisson's ratio of mixed soil is a variational state parameter with the change of stress state, it decreases with increased confining pressure, and it increases with increased stress level. When axial strain is near 5%, Poisson’ ratio is gradually close to a steady value. The main range of Poisson's ratio is 0.25～0.50 when confining pressure changes from 50 to 300 kPa. When unconfined compressive strength of mixed soil is less than 328 kPa, its stress-strain-volumetric strain characteristics can be predicted very well by Duncan-Chang model (E-B model). However, when the range of unconfined compressive strength is [328 kPa, 566 kPa], the model can't predict stress-strain characteristics accurately when confining pressure is under 200 kPa, and it also can't predict the strong shear dilatancy phenomenon of mixed soil under low confining pressure.     

循环应力下饱和黏土剪切变形特性试验研究

针对饱和重塑黏土,利用土工静力-动力液压三轴-扭转多功能剪切仪,在不固结不排水(UU)条件下进行了应力控制式循环扭剪和竖向-扭转耦合试验,通过对试验结果的对比分析探讨了初始预剪应力和应力反向对应力-应变关系特性的影响,并阐述了不同加荷模式下孔隙水压力发展特性。以此为基础,综合考虑剪切变形和正向偏差变形的共同效应,同时为了能够反映平均残余变形和循环变形的影响,建议了一个综合应变破坏标准的算式。进而通过利用试验数据与目前常用的应变标准比较,表明这种破坏标准具有普遍适用性和较好的稳定性,适用于判定各种应力条件下黏土试样破坏及其强度。     

Research on shaft resistance of rock-socketed piles based on the cavity expansion theory

The shaft resistance of rock-socketed piles depends not only on the properties of its surrounding rock, but also on the radial force induced by the load imposed on the top of the pile. This paper deduced a plastic zone of rock around a single pile and obtained the shaft resistance of a rock-socketed pile based on the theories of cavity expansion and shear strength. The research results showed that the magnitude of the radial force in the socketed portion of a rock-socketed pile was related to the pile diameter, Poisson’s ratio, and properties of the surrounding rock. The influence area of rock decreased with increasing pile diameter. The radial force and lateral friction decreased with the increasing relative stiffnesses of the pile and rock. The radial stress on the elastic–plastic interface can be analytically determined based on the rock properties and depth. A field test was used to validate the proposed method, and a good agreement was obtained between the field data and predicted results of the proposed method. The research results in this paper are beneficial to guide actual practice.     

Strain-Rate Dependent Stress--Strain Behavior of Undisturbed Hong Kong Marine Deposits under Oedometric and Triaxial Stress States

This article presents a testing study on the strain-rate effects on the stress--strain behavior of natural, undisturbed Hong Kong marine deposits (HKMD) from three Hong Kong locations, including a one-dimensional (1-D) compressibility in a confined condition, and undrained shear strengths in triaxial compression and extension modes. The influences of the strain rates on the one-dimensional compressibility are studied by means of constant rate of strain (CRS) tests and multistage loading oedometer (MSL) tests, and those on the undrained shear strengths are studied by K_o-consolidated undrained compression and extension tests with step-changed axial strain rates (CK_oUC and CK_oUE tests), and with both step-changed axial strain rates and relaxation processes (CK_oUCR and CK_oUER tests). The strain-rate effects on the stress--strain behavior are generally examined by “apparent” preconsolidation pressures in the 1-D compressions and undrained shear strengths in the triaxial compression and extension stress states. The stress--strain behavior of the natural, undisturbed HKMD exhibits considerable viscous characteristics. In the CRS and MSL tests at a given strain, the higher the strain rate, the higher the effective stress, the higher the porewater pressure. In the undrained shearing tests, the higher the strain rate, the higher the undrained shear strength, but the lower the porewater pressure. For the CK_oUC and CK_oUE tests on the Tsing Yi site samples, the undrained shear strength increases by 8.5% and 12.1% for one order increment of axial strain rate of 0.2%/hr (i.e., ρ_0.2) for the compression and extension modes respectively. For the CK_oUCR and CK_o tests on the Tung Chung site samples of different compositions, average ρ_0.2 is increased by 6.2% for the compression and 9.5% for the extension, but by 18.8% for the extension on a higher plastic sample. The present study shows that the strain-rate effects on the stress--strain behavior of the undisturbed HKMD are larger for specimens in extension than those in compression.     

Experimental simple shear study of composite soil with cemented soil core

Abstract

Cement soil mixing piles are an effective treatment method for marine soft clay. To investigate the static and dynamic characteristics of the composite soil with cemented soil core, a series of experiments are carried out by using the cyclic simple shear test. The result shows that, the static shear strain showed strain hardening, cemented soil core can improve static shear strength of composite soil, vertical stress can enlarge reinforcement of cemented soil core. The tendency of strain development of composite soil with different area replacement ratios under cyclic loading is the same as that of pure clay, existing critical cyclic stress ratios corresponding to different area replacement ratios. In addition, improving area replacement ratio can increase cyclic strength. At same time, adding of cemented soil core does not change shape of hysteresis curve compared with it for clay either. Moreover, cemented soil core can also obstruct stiffness softening. Through regression analysis of the experimental data, relationship between cyclic number and soil softening index is proved to be linear. The results can give a reference for the dynamic characters of the marine soft clay foundation with cement soil mixing piles.     

海洋粉质粘土在波浪荷载作用后的不排水抗剪强度衰化特性

通过对南海重塑粉质粘土土样的大量动三轴试验结果分析,得到此种土在波浪荷载作用后不捧水抗剪强度衰化同动载作用引起的动应变幅及平均累积孔压之间的相互关系和预估公式;并通过与超固结土样的静三轴剪切试验结果的比较,发现动、静三轴两种试验结果具有很好的吻合关系。建议可用超固结土样的静三轴剪切试验同时结合部分动三轴试验来预估土样在波浪荷载作用后不排水抗剪强度衰化与平均累积孔压之间的关系。     

Numerical study on long-term monopile foundation response

This paper analyzes the long-term monopile foundation that undergoes numerous mechanical cycles. The semiempirical scheme is adopted to involve a mechanical constitutive model to extract stress and strains at the first cycle and polynomial-type strain accumulation functions to track the progressive plastic deformation. In particular, the strain function contains the fundamental features that require simulating the long-term response of geomaterials: volumetric strain (terminal void ratio) and shear strain (shakedown or ratcheting), the strain accumulation rate, and stress obliquity. The numerical simulation shows evolution of displacements, pile rotation, and stress redistribution along the embedded pile as the number of load cycles increases. The analysis highlights that the pile rigidity affects the pattern of horizontal stress and displacement. The repetitive lateral load enhances the lateral load resistance due to soil densification along the pile.