砖墙-钢筋混凝土墙组合结构震害预测方法

建筑物震害预测对于制定城市防震减灾规划意义重大,对于我国高烈度区建造的砖墙-钢筋混凝土剪力墙组合结构,目前没有成熟的震害预测方法.为了预测西昌市砖墙-钢筋混凝土剪力墙组合结构建筑物在不同地震烈度下可能发生的震害程度,通过分析该种结构在不同地震作用下的受力特点,提出以结构薄弱层的楼层屈服强度系数为指标进行震害预测,并结合...     

Seismic response of tied-back retaining walls

Parametric studies based on finite element simulations were conducted to establish the fundamental mechanisms by which tied-back walls respond to travelling displacement pulses. Considering first linear elastic soil behaviour, we observed that the flexural stiffness of the wall hardly affects maximum transient displacements. Rather, the transient response is determined mainly by the ratio of pulse wavelength to wall height. The maximum load carried by the anchor was found to increase with increasing anchor stiffness. For short wavelengths, on the order of less than two times the wall height, the maximum displacements and displaced shapes are affected significantly by the inclination of the anchor. The importance of the anchor stiffness suggested by the linear elastic analysis was confirmed by the non-linear analysis. A stiff anchor suppressed permanent displacements in the vicinity of the anchor, but did not substantially reduce permanent displacements elsewhere. As peak accelerations increased from 0.1 g to 0.4 g, permanent wall displacements increased significantly.     

Seismic response of precast concrete walls

Large panel precast concrete structures are built in major seismic regions throughout the world. The seismic behaviour of such structures is strongly dependent upon the characteristics of both the horizontal and vertical connections. The limiting behaviour of precast systems, however, is basically dependent upon the horizontal connection. The influence of horizontal connections can be studied in terms of the behaviour of a simple wall—a vertical stack of panels having only horizontal connections. This paper reports on research into the seismic behaviour of simple precast concrete walls. The research was carried out through the development of computer-based modelling techniques capable of including the typical behavioural characteristics associated with horizontal joints. The model assumes that all non-linear, inelastic behaviour is concentrated in the connection regions and that the precast panels remain linear elastic. This assumption allows the precast panels to be modelled as statically condensed ‘super-elements’ and the connection regions as interface elements. The above modelling technique allows for non-linear-inelastic seismic analysis that is capable of handling both rocking type motions throughout the height of the structure and slippage due to shear in the plane of the connection. A series of parametric studies are presented to illustrate the potential influence of rocking and slip on precast walls with both regular reinforcement and post-tensioning. These studies demonstrate the period elongation associated with the nonlinear-elastic rocking phenomenon. Shear slip is found to occur only when friction coefficients are extremely low or when the normal forces across the connections are low. This latter case occurs only in low buildings or in the upper floors of tall buildings. The paper concludes with a brief discussion of the design implications of these results. Particular attention is paid to the problems stemming from the force concentrations associated with rocking and shear slip.     

Free vibrations of open-section shear walls

The coupled torsional-flexural vibration of open-section shear walls, braced by connecting beams at each floor level, is analysed on the basis of Vlasov's theory of thin-walled beams. The basic dynamic equations and boundary conditions are derived from Hamilton's principle, and a numerical solution obtained by the Ritz-Galerkin method. In addition to the primary torsional and flexural inertias, secondary effects due to rotatory and warping inertia forces have also been taken into account. The method is suitable for both rigid and flexible base conditions. A series of numerical examples is presented in which analytical results are compared with available experimental data, and the effects of secondary inertia forces, base flexibility and connecting beams upon the vibration characteristics of such shear walls are examined for two different structural forms.     

Sectional response of T-shaped RC walls

Deformation quantities such as strain, curvature and displacement are of paramount importance in seismic design within a performance-based procedure that aims to control the structural response at predefined levels of inelastic action. Given the importance of curvature expressions independent of strength for the design process, and for the particular case of T-shaped walls, the curvature trends at yield, serviceability and ultimate limit state are determined in graphical and analytical form. The comprehensive set of equations proposed in this work are strength independent and allow the reliable computation of limit-state curvatures, essential in a displacement-based design approach, and thus the realistic estimation of appropriate ductility factors in the design of T-shaped walls. Furthermore, results regarding the section properties of T-shaped walls, such as the elastic stiffness and the moment capacity for opposite directions of loading, offer additional information on T-shaped walls.     

Free vibrations of coupled shear walls

The continuous connection method of analysis is extended to deal with the free vibrations of a coupled shear wall structure. The natural modes and frequencies are determined from the Galerkin technique, and the dynamic response following an imposed lateral displacement is evaluated. A comparison is made between theoretical predictions of natural frequencies and the results from tests on model structures.     

Seismic behaviour of confined masonry walls

The results of tests of plain and confined masonry walls with h/l ratio equal to 1·5, made at 1:5 scale, have been used to develop a rational method for modelling the seismic behaviour of confined masonry walls. A trilinear model of lateral resistance–displacement envelope curve has been proposed, where the resistance is calculated as a combination of the shear resistance of the plain masonry wall panel and dowel effect of the tie-columns’ reinforcement. Lateral stiffness, however, is modelled as a function of the initial effective stiffness and damage, occurring to the panel at characteristic limit states. Good correlation between the predicted and experimental envelopes has been obtained in the particular case studied. The method has been also verified for the case of prototype confined masonry walls with h/l ratio equal to 1·0. Good correlation between the predicted and experimental values of lateral resistance indicates the general validity of the proposed method. © 1997 John Wiley & Sons, Ltd.     

Bidirectional behavior of unreinforced masonry walls

Most of the studies related to the modeling of masonry structures have by far investigated either the in‐plane (IP) or the out‐of‐plane (OP) behavior of walls. However, seismic loads mostly impose simultaneous IP and OP demands on load‐bearing or shear masonry walls. Thus, there is a need to reconsider design equations of unreinforced masonry walls by taking into account bidirectional effects. The intent of this study is to investigate the bidirectional behavior of an unreinforced masonry wall with a typical aspect ratio under different displacement‐controlled loading directions making use of finite element analysis. For this purpose, the numerical procedure is first validated against the results of the tests on walls with different failure modes conducted by the authors. Afterward, the response of the wall systems is evaluated with increasing top displacement having different orientations. A set of 19 monotonic and three cyclic loading analyses are performed, and the results are discussed in terms of the variation of failure modes and load–displacement diagrams. Moreover, the results of wall capacity in each loading condition are compared with those of the ASCE41‐06 formulations. The results indicate that the direction of the resultant force, vectorial summation of IP and OP forces, of the wall is initially proportional to the ratio of stiffness in the IP and the OP directions. However, with the increase of damage, the resultant force direction inclines towards the wall's longitudinal direction regardless of the direction of the imposed displacement. Finally, recommendations are made for applicability of ASCE41‐06 formulations under different bidirectional loading conditions. Copyright © 2014 John Wiley & Sons, Ltd.     

Dynamic soil pressures on rigid vertical walls

A critical evaluation is made of dynamic pressures and the associated forces induced by ground shaking on a rigid, straight, vertical wall retaining a semi-infinite, uniform viscoelastic layer of constant thickness. The effects of both harmonic and earthquake-induced excitations are examined. Simple approximate expressions for the responses of the system are developed, and comprehensive numerical data are presented which elucidate the effects and relative importance of the various parameters involved. These solutions are then compared with those obtained by the use of a simple model previously proposed by Scott, and the accuracy of this model is assessed. Finally, two versions of an alternative model are proposed which approximate better the action of the system. In the first, the properties of the model are defined by frequency-dependent parameters, whereas in the second, which is particularly helpful in analyses of transient response, they are represented by frequency-independent, constant parameters.     

Evaluation of seismic displacements of quay walls

A new simplified dynamic analysis method is proposed to predict the seismic sliding displacement of quay walls by considering the variation of wall thrust, which is influenced by the excess pore pressure developed in backfill during earthquakes. The method uses the Newmark sliding block concept and the variable yield acceleration, which varies according to the wall thrust, to calculate the quay wall displacement.A series of 1 g shaking table tests were executed to verify the applicability of the proposed method, and a parametric study was performed. The shaking table tests verified that the proposed method properly predicts the wall displacement, and the parametric study showed that the evaluation of a realistic wall displacement is as important as the analysis of liquefaction potential for judging the stability of quay walls.     

Approximate natural frequencies for coupled shear walls

An approximate yet accurate formula is proposed for the natural frequencies of coupled shear walls under continuous medium assumptions. First the deflected shape of the structure is represented as the sum of two components: one due to flexural cantilever action and one due to shear-flexure cantilever action. The natural frequencies of the latter two systems are then combined in Dunkerley's formula to yield the approximate frequency of the structure.     

Seismic stability of retaining walls with surcharge

The use of pseudo-static methods for the computation of soil thrust acting on retaining walls under seismic condition is well established in the design of such structures. Although different methods, based on the limited displacement concept, have been developed in the last 20 years, the most common design method is still the method derived from the theory developed by Mononobe and Okabe. However, the Mononobe–Okabe method presents a basic shortcoming: the solution is based on the limit equilibrium of the soil wedge without taking into account the presence of the wall. In the paper a new solution based on the pseudo-static equilibrium of the soil–wall system is presented. The developed solution takes into account the effect of the presence of the wall and it is applied to soil–wall systems with surcharged backfills. Formulas are provided to calculate directly the yield acceleration and the inclination of the failure surface. The effect of the intensity of the surcharge and of its distance from the wall is investigated and the results are compared to those obtained in the case of soil–wall systems without surcharge.     

The inspection of retaining walls using GPR

In hilly regions, retaining walls along roads, motorways and railway lines are numerous. In some cases the knowledge of the details of the construction is limited. If rehabilitation work becomes necessary, a detailed knowledge of the construction is desirable for the improved planning of maintenance and repair. This paper describes the application of Ground Penetrating Radar (GPR) for the inspection of retaining walls. The work was carried out in two steps. First, an investigation was carried out on large retaining walls at a Swiss motorway within the framework of a service contract. This included the development of an apparatus enabling high precision positioning of the antennas on the walls. Second, a pilot study was performed on a smaller wall with optimized acquisition and processing parameters. This included the use of antennas with different orientations and the fusion of the two corresponding datasets as well as true 3-D data processing. This paper describes the approaches to data acquisition and processing in the form of the two case studies. Results from different acquisition and processing strategies are compared and the benefits and limits are discussed.     

Static inelastic analysis of RC shear walls

A macro-model of a reinforced concrete (RC) shear wall is developed for static inelastic analysis. The model is composed of RC column elements and RC membrane elements. The column elements are used to model the boundary zone and the membrane elements are used to model the wall panel. Various types of constitutive relationships of concrete could be adopted for the two kinds of elements. To perform analysis, the wall is divided into layers along its height. Two adjacent layers are connected with a rigid beam. There are only three unknown displacement components for each layer. A method called single degree of freedom compensation is adopted to solve the peak value of the capacity curve. The post-peak stage analysis is performed using a forced iteration approach. The macro-model developed in the study and the complete process analysis methodology are verified by the experimental and static inelastic analytical results of four RC shear wall specimens. Supported by: National Natural Science Foundation of China, Grant number 59895410     

Seismic resistance of precast concrete shear walls

The earthquake resistance of stacked precast concrete simple shear walls found typically in Large Panel buildings of the cross-wall type is studied. Physical model testing on a small shaking table facility and analytical techniques are compared. Results of the testing of four models to failure portrayed the non-linear effects of rocking and shear slip that were assumed in several analytical studies but were never before measured experimentally. The physical model studies are supplemented with an independent mathematical analysis using a modified version of the dynamic, non-linear computer code Drain 2–D. Correlation of the analytical and experimental results show that the computer study can be used to predict the overall shear wall response. Results of the small scale model and the mathematical model studies indicate that the simple shear wall behaves in a non-linear manner, even for low magnitudes of base acceleration. Non-linear effects, usually concentrated in only one or two joints, reduced force levels and increased displacements. The four small scale models that were tested withstood high magnitudes of base acceleration without collapse.     

Seismic stability analysis of gravity retaining walls

A new approach based on the category of upper bound theorem of limit analysis is presented in this study to consider the seismic stability of gravity retaining walls. The retaining wall and the backfill soil were taken as a whole system. For a translational failure mechanism assumed, formulas are provided to calculate directly the yield acceleration and the inclination of the failure surface. An example is shown to illustrate the method. Comparisons are made with limit equilibrium method, and the results are found consistent. Based on a limited parametric study, it is shown that the wall roughness has remarkable influence on the yield acceleration.     

Seismic response of multi-tiered reinforced soil retaining walls

In this study, a validated Finite Element procedure was used to investigate the similarities and differences of seismic performances between single- and multi-tiered reinforced soil walls. Three-tiered walls at a total height of 9 m were analyzed together with vertical walls at the same height. It was found from the Finite Element analyses that the resonant frequency of reinforced soil walls might increase with an increase in the tier-offset. The multi-tiered configuration could considerably reduce the residual lateral facing displacement and the average reinforcement load, and the reinforcement load distribution with height was different from that in vertical walls. With the same reinforcement length and spacing, the multi-tiered walls resulted in smaller reinforcement connection loads with the facing blocks. The study filled the gap of seismic behavior of multi-tiered reinforced soil retaining walls and revealed a few unique dynamic properties of this type of earth structures.