不同围压下饱和砂土不排水循环扭剪试验研究

利用河海大学与日本圆井株式会社共同研制的一种新型的多功能静动三轴仪进行了不排水循环扭剪试验。通过对空心圆柱体试样的动力扭剪不排水试验研究了相同相对密度在不同固结围压下的动力不排水响应。试验初步研究了通过用初始有效平均正应力归一化的有效应力路径,归一化有效应力路径有很好的一致性。如果保持相同的剪应力比,由初始有效平均正应力归一化的有效应力路径不受初始有效平均正应力的影响。     

残积土抗剪强度的环剪试验研究

残积土风化剧烈,研究其大变形下的工程特性很有必要。利用环剪仪的试验特点,可以研究土体在较大剪切位移下抗剪强度的变化规律。通过对残积土残余和峰值强度的环剪试验测定和对试验数据的整理与对比分析,得到了含水率与残余强度指标之间的关系,证明大变形下残积土具有浸水软化的特性;从应变阈值角度分析了残积土应变软化的性质,不同剪切位移下的残积土具有不同的抗剪强度,所研究的残积土达到峰值强度对应的应变介于0.02～0.06之间,而到达基本稳定的残余强度所需要的应变介于0.06～0.20区域内。研究还发现,矿物成分不同直接影响到残积土的残余强度,是残积土不均匀性的内部因素     

宽级配砾质土快速三轴固结排水剪试验影响因素研究

宽级配砾质土是由砾石料和黏土料按一定比例混合而成,其具有压缩性低、抗剪强度大等特点,目前常作为土石坝心墙料或路基填料而得到广泛应用。由于宽级配砾质土渗透系数较小,在常规三轴固结排水剪(CD)试验中固结排水较慢,导致其试验周期很长。为了提高固结排水的效率,可采用一种在试样中心加圆柱形砂芯的快速三轴CD试验方法。基于快速三轴CD试验,通过变化不同砂芯类别、不同砂芯直径、不同掺砾量等各因素,全面研究了各因素对宽级配砾质土快速三轴CD试验的影响。研究结果表明,快速三轴CD试验方法能够有效加快试样排水固结,从而加快整个试验进程;砂芯类别、砂芯直径、掺砾量等因素均对试验固结排水速度和剪切过程应力应变产生不同程度影响;砂芯直径越小,其试验成果与无砂芯试样越接近。     

Quadruple LVDT local rotational displacement measurement in torsional shear tests

Experience has shown that to obtain pre-failure deformability of geomaterials in laboratory element tests, it is imperative to make local strain measurements. For torsional shear tests, the local measurement is complicated by coupling of the axial, radial, and rotational movement experienced by the soil specimen during shear. The rotational displacement must be isolated from other modes of movement for the interpretation of test results. Existing techniques designed for torsional shear tests under general stress conditions can be complicated and difficult to use. A simplified scheme using two pairs of linear variable displacement transducers (LVDTs) is proposed for local rotational deformation measurement, specifically for cyclic torsional shear tests under constant normal stress conditions. The subtraction of readings within an LVDT pair nullifies displacements at the measurement point caused by axial and radial movement or bulging of the specimen. The same subtraction accumulates and thus isolates LVDT readings caused by rotational movement. The error associated with the simplified set-up is expected to be <0.125%. A series of hollow cylinder torsional shear tests have been performed to verify the effectiveness of the new measurement scheme. The results are repeatable and consistent with well-documented test data.     

Undrained shear testing of jointed rock

SummaryUndrained Shear Testing of Jointed Rock Water pressures must change inside joints undergoing shear without perfect drainage. This paper describes a new direct shear machine in which jacketed samples with oriented joints can be tested under consolidated undrained conditions with pore pressure measurement. Triaxial compression techniques for such tests are also described and typical results with intact and jointed sandstone samples are compared with results from the direct shear tests. Whereas intact specimens displayed increasing pore pressure followed by dilatancy and pore pressure decline before peak loading, the pore pressure in jointed specimens continued increasing right up to the peak load.

---

ZusammenfassungScherversuche an klüftigen Gesteinen ohne Dränung Wasserdruck in Klüften muß sich verändern, wenn ohne perfekte Dränage Scherkraft ausgeübt wird. In der vorliegenden Arbeit wird ein neuer, direkt wirkender Scherapparat beschrieben, in welchem ummantelte Prüfkörper mit gerichteten Klüften unter Konsolidationsbedingungen ohne Dränage untersucht werden können, wobei der Porendruck gemessen wird. Es wird außerdem die Technik von Triaxialversuchen beschrieben und typische Ergebnisse mit ungestörtem und geklüftetem Sandstein werden mit Ergebnissen aus direkten Scherversuchen verglichen. Während ungestörte Proben steigenden Porendruck, gefolgt von Dilatanz, aufweisen und der Porendruck vor der Höchstbelastung nachläßt, nimmt derselbe in geklüfteten Proben bis zur Höchstbelastung ständig zu.

---

RésuméEssais de cisaillement non drainé sur des échantillons de roche contenant une discontinuité Les pressions interstitielles à l'intérieur des discontinuités doivent changer lorsqu'elles sont soumises au cisaillement et que le drainage n'est pas parfait. Cet article décrit une nouvelle machine pour essais de cisaillement direct permettant de tester, dans des conditions de consolidation non drainée, des échantillons de roche gainés comportant une discontinuité d'orientation déterminée. La machine permet la mesure de la pression interstitielle.L'article décrit également les techniques de compression triaxiale correspondantes et des résultats typiques obtenus sur des échantillons de grès intact ou traversé par un joint sont comparés à ceux provenant des essais de cisaillement direct. Alors que les échantillons de roche intacte montrent un accroissement de la pression interstitielle suivi de dilatance et d'une réduction de pression avant que la contrainte de cisaillement maximum ne soit atteinte, la pression interstitielle dans les échantillons contenant une discontinuité croît jusqu'au droit de la contrainte de cisaillement maximum.

---

---

With 11 Figures     

Influence of gravelly exclusion on compaction of lateritic soils

This paper uses a deltaic lateritic soil sample to study the combined influence of total gravel composition and gravelly exclusion on compaction parameters MDD (or maximum dry density) and OMC (or optimum moisture content) derived from standard laboratory compaction tests. In the end, MDD was found to vary polynomially with percentage of gravelly exclusion with improved or higher values as total gravel composition increases. OMC on the other hand was found to decrease continually with increasing gravelly exclusion but independent of the total gravel composition. Also, a model was presented in form of a family of curves to predict actual or field compaction parameters (which is devoid of gravelly exclusion) and their laboratory counterparts. This revised version was published online in July 2006 with corrections to the Cover Date.     

高压力下原状层间错动带三轴不排水剪切特性及其影响因素分析

针对某大型水电站揭露的原状层间错动带试样,模拟现场快速施工可能会产生的不排水边界条件,在围压5～30 MPa的高压力条件下开展了不固结不排水三轴试验,并结合试样物理性质的差异,分析讨论了原状层间错动带的力学特性。试样试验曲线和破坏模式主要由高围压控制：其应力-应变关系曲线均为应变硬化型且破坏后呈腰鼓状为塑性破坏。此外,较湿颗粒发生了大规模的颗粒破碎,其是造成高饱和度试样强度包线的趋势线随围压降低的根本原因。试验结果明显受物理性质影响造成了试验数据离散性,敏感性分析表明,围压P和饱和度 对初始弹性模量 和破坏强度 的影响最大,其次是孔隙比e,颗粒粒径（ ）分布对其影响程度最小。根据试样剪切特性建立的强度特征（ 和 ）初步预测公式可供实际工程参考。     

钙质土的剪切特性试验研究

钙质土因其颗粒形状不规则、易破碎、高孔隙比等特征,其力学性质较为特殊。采用室内大型直接剪切试验设备,对取自南海珊瑚礁和三亚岸礁的粗颗粒钙质土进行了直剪试验,研究了粗颗粒钙质土在不同含水率、不同密度和不同矿物组成条件下的钙质土剪切特性。结果表明,粗颗粒钙质土表现出与常规无黏性土截然不同的力学性质,即（1）与石英砂相比,表观黏聚力较大,内摩擦角较高,软化性较弱;（2）表观黏聚力随着平均粒径的增大而增大,内摩擦角随着干密度的增大而增大;（3）与峰值强度相比,土体剪切破坏后其残余强度的表观黏聚力锐减而内摩擦角仅略有减小。研究成果可为岛礁工程建设提供借鉴,也可为其他粗颗粒土的研究提供参考。     

基于大型直剪试验的强风化粗粒料剪胀特性试验研究

剪胀性是岩土材料的重要特性之一,为研究不同工况条件下粗粒料室内大型直剪试验中的剪胀特性,采用新型室内大型直剪仪对3组不同含水率、4组不同剪切速率、5组不同含砾率等3种不同影响因素的试样进行了室内大型直剪试验,分析了剪切时试样的垂直位移与水平剪切位移及垂直应力的关系。试验结果表明：在保持其他影响因素相同条件下,垂直应力的增加导致相同水平剪切位移对应的剪缩量增加;试样的最大剪缩量随着含水率的增加有一定程度的增大,而随着剪切速率的增加而减小;含砾率低于30%试样的最大剪缩量较含砾超过于30%试样的剪缩量大很多,最大剪缩量差别为3倍。当试样含砾率小于50%时,由于试样中富含细颗粒的影响,使得应力-应变曲线具有应变软化属性以及剪胀性趋于一固定值。峰值强度前的应力比-位移增量关系采用非线性的二次项拟合比线性关系的拟合度更好,认为Matsuoka提出的二维剪胀公式不适用于粗粒料,将其修正成二次多项式并给出试验中的经验参数μ的取值区间。     

Constitutive modeling of dense gravelly soils subjected to cyclic loading

A constitutive model for dense gravelly soils was developed to reproduce their responses under cyclic loadings. Its application aims at nonlinear dynamic analyses of earth structures involving gravelly soils, such as rockfill dams and railroad ballasts. The framework of generalized plasticity was modified to incorporate the concept of stress distance for better simulation of unloading and reloading responses. It was then combined with the theory of critical state soil mechanics to develop the constitutive model. The model has the following important features: unified simulation of particle breakage through translating critical state line, smooth transition from unloading to reloading in the stress space, and proper modeling of cyclic hysteresis, cyclic densification, and cyclic hardening of dense gravelly soils. Most of the model parameters can be obtained through simple calculation using conventional triaxial test results, and their calibration process was discussed. The model was used to simulate the cyclic responses of three gravelly soils with satisfactory accuracy. Copyright © 2014 John Wiley & Sons, Ltd.     

不同应力条件下砾石土防渗料和反滤料联合抗渗试验研究

利用自行研制的可提供高水压、高应力的粗粒土大型高压渗透仪,对双江口砾石土心墙堆石坝防渗料和反滤料进行了联合抗渗试验,研究不同应力状态下防渗料和反滤料的渗透变形特性。结果表明：（1）单向压缩条件下,防渗料的渗透系数随应力的增加而减小,且渗流稳定时的渗透系数与应力的关系满足Louis负指数方程;试样发生破坏的临界坡降随应力的增加而增大。（2）水平加荷、竖向自由变形条件下,试样的渗透系数随水平应力的增加先减小后增大。试样发生破坏的临界坡降随水平应力的增加先增大后减小。在达到峰值之前,反滤料越松或越细,临界坡降随水平应力增大的幅度越大;在达到峰值之后,反滤料越密或越细,临界坡降随应力减小的幅度越大。     

Use of discrete element modeling to study the stress and strain distribution in cyclic torsional shear tests

In this research, a torsional cyclic shear test was modeled using the 3D discrete element method (DEM). The results are compared against experimental data and micro-mechanical aspects of the soil during the loading are discussed. The aim of the work is to study the homogeneity of strains during this laboratory test and to compare the micro-mechanical behavior of the soil sample for different strain levels. The experimental investigation was performed using a synthetic soil material made of glass beads, which simplifies the modeling and calibration since normal interaction forces do not induce rotation of the particles. Both the model and experimental tests used the same grading distribution and particle size. We showed that the hysteresis cycles can be properly reproduced in terms of shape and magnitude. Thus, we obtained a robust estimation for the secant shear modulus and damping ratio at different strain levels. With this, it was possible to build stiffness degradation and damping increase curve to compare it with experimental data obtained from torsional shear tests. Based on this validation of the DEM model, we discuss the micro-mechanical behavior of the soil and its relation with the macroscopic parameters obtained. It is shown that shear strain distribution on the sample is not uniform and that large values of strains concentrate close to the top of the sample as top rotation increases, which differs from the standard assumption of a constant value across the height of the sample. Additionally, it is observed that at 0.8 times radius, the cumulative torque reaches approximately 90% of the total torque applied to sample.     

钙质砂抗剪强度特性的环剪试验

珊瑚礁沉积的钙质砂与石英砂的物理力学性质有较大差别。对取自南海岛礁的钙质砂进行了单次往返环剪试验以分析钙质砂的抗剪强度特性,试验中考虑了相对密实度和竖向应力对结果的影响,并与相同级配和试验条件下的石英砂进行对比分析。结果表明：钙质砂正向剪切时应力-位移曲线为软化型,具有明显的残余强度特性,而反向剪切时则表现为硬化型,正向和反向剪切强度基本一致;石英砂正向剪切和反向剪切均表现为软化型。钙质砂正向剪切和反向剪切残余强度与峰值强度的比值在0.75～0.93之间;石英砂正向剪切和反向剪切残余强度与对应峰值强度的比值在0.89～0.96之间。相同级配和试验条件下,钙质砂残余强度均大于石英砂,且强度比值基本保持在1.05～1.3之间。在100、200 kPa竖向荷载作用下,钙质砂0.5～2.0 mm的颗粒发生了破碎,破碎率分别为4%和6%。     

基于有效固结应力法确定结构性黏性土不排水抗剪强度

由于结构性的存在使得很多天然黏性土的强度和变形特性不同于重塑土和非结构性土。首先回顾了适用于确定重塑土和非结构性土不排水抗剪强度的有效固结应力法,并推导了相应的方程。在此基础上,对于结构性黏性土,采用两段不同斜率（内摩擦角正切）和截距（黏聚力）的直线模拟其抗剪强度包络线,建立了确定其不排水抗剪强度的有效固结应力法方程;当有效应力小于结构屈服应力时,有效固结应力方程中有效应力部分需乘以0.8的修正系数;只要已知剪切前的有效应力,利用相应的有效固结应力法公式,可确定结构性土体的不排水抗剪强度。利用连云港结构性软黏土的等压固结三轴试验数据,验证了有效固结应力法的适用性。分析表明：对于连云港软黏土的不排水抗剪强度,有效固结应力法的计算结果与试验结果吻合较好;对于结构屈服应力,有效固结应力法的预测结果与试验数据点的拟合结果有一定偏差,但并不明显。     

Undrained cavity expansion in anisotropic soils with isotropic and frictional destructuration

This paper proposes a semi-analytical solution of undrained cylindrical cavity expansion in anisotropic soils with both isotropic and frictional destructuration. The rigorous derivation based on the general form of the SANICLAY model with destructuration is provided following a standardized solving procedure, and the features of anisotropy and structuration are then invoked in the cavity expansion solution by adopting the non-associated hierarchical model. Cavity expansion tests in both structured and unstructured clays with various overconsolidation ratio are conducted to investigate the evolutions of effective stresses, excess pore pressure, anisotropic parameters and structuration factors during cylindrical expansion. The results show that the effective stresses at the cavity wall are lower after expansion and the cavity excess pore pressure is oppositely higher in structured clays with slightly smaller plastic regions. The evolutions of anisotropy for structured clays appear to follow similar patterns to unstructured cases, whereas the degree of anisotropy is further developed with gradual loss of inter-particle bonds. Finally, the proposed solution is applied to predict the limit pressure of pressuremeter tests in Bothkennar clay, showing its ability for interpretation of in situ testing data in natural structured clays.

     

土工静动力液压三轴扭转剪切仪控制软件系统研究

根据土工试验使用要求,应用计算机自动化控制技术,将大连理工大学与日本诚研社合作研制的新型土工静力-动力液压三轴-扭转多功能剪切仪,配备了完善的控制软件系统。采用VC++6.0语言作为编程平台,利用现代计算机技术中的多线程技术、精确定时技术、绘图技术,结合现代的单神经元自适应PID控制理论,实现了三轴-扭转试验机的自动控制及数据采集处理功能,能够完成静态、动态等各种组合试验,并可实时监测试验全过程的应力、应变和位移等12种数据,绘制实时动态曲线,更加方便试验者操作,进一步提高了系统的控制精度。     

再论非饱和土的抗剪强度

通过不同吸力状态下的非饱和土抗剪强度试验,探讨了基质吸力对黏聚力和摩擦角的影响,提出在不同的基质吸力条件下黏聚力和摩擦角均可能是变化的。非饱和土的抗剪强度包络面在几何学上是直纹面的一种,该包络面可用改进的摩 尔-库仑破坏准则描述,并用试验验证了该公式的合理性。结合改进的摩尔-库仑抗剪强度公式和具体试验,提出了等效黏聚力-吸力曲线和等效摩擦角-吸力曲线在一定的区间内近似为直线,给出了确定等效黏聚力和等效摩擦角的具体方法,并用干土和饱和土两种极端状态对3种非饱和土抗剪强度理论进行了评估。改进的摩尔库仑破坏准则是一种更真实描述非饱和土破坏的强度准则。     

基于动力触探的砾性土液化判别方法通用性研究

能量传递率是衡量贯入类试验锤击效率的一个重要指标。国外对这一指标需要进行现场实测,进而修正贯入试验的锤击数,建立评价场地承载力、液化势等特性的标准化锤击数。国内规范中,则较少考虑贯入试验的锤击能量传递率的问题,且缺少现场试验测试数据,导致基于贯入类试验锤击数的地基评价方法难以与国外标准进行横向对比。为解决这一问题,选取川滇地区西昌地震实验场的3个勘察试验点。采用能量测试仪实测标准贯入试验能量传递率,研究我国常规SPT试验装置锤击效率,并评价其稳定性。试验实测结果显示,现场标准贯入试验的锤击能量传递率均值基本超过75%。能量传递率随着贯入深度的增加稍有增加,地表下20 m范围内增长幅值为10%左右。试验结果可为评价我国常规SPT试验设备的锤击效率提供依据。     

重塑硅藻土抗剪强度的环剪试验研究

硅藻土是一种强结构性土,具有密度小、孔隙大、干燥土块吸水率高等特点。天然硅藻土的抗剪强度大,但在外界扰动或风化后,结构性强度丧失,易发生滑坡等斜坡变形破坏现象,因此,研究其在大变形下的力学性质很有必要。利用环剪仪可以研究土体在较大剪切位移条件下抗剪强度变化规律,对重塑硅藻土进行环剪试验研究,得到了不同竖向压力下的应力-位移曲线,认为重塑硅藻土为典型的应变软化型土;根据测试结果得到了重塑硅藻土的抗剪强度和残余强度,并从物质组成和微观结构特征方面对重塑硅藻土的力学性质进行了分析,为硅藻土滑坡的成因分析和灾害防治提供了依据。     

初始静剪应力对粗粒土与结构接触面循环力学特性的影响

运用80 t大型三维接触面试验机,对初始静剪应力存在时粗粒土与结构接触面循环力学特性及初始静剪应力大小的影响进行了研究。循环剪切时,接触面沿初始静剪应力方向产生了明显的切向位移,且该位移与正交切向的剪切路程基本呈直线关系,该直线与初始静剪应力的夹角和初始静剪应力水平关系可用二次多项式描述。初始静剪应力大小对接触面抗剪强度、正交切向应力-应变关系形式影响较小,主要影响正交切向应力峰值、接触面剪切体变数值及剪切体变与切向位移关系等。初始静剪应力越大,该方向产生的切向位移越大,其正交切向应力峰值越小,该应力峰值对应的切向位移亦越小,接触面剪切硬化程度越高;初始剪切时接触面剪胀量越大,而后期循环剪切时剪缩量和剪胀量则越小。