Estimating field‐saturated soil hydraulic conductivity by a simplified Beerkan infiltration experiment

Field‐saturated soil hydraulic conductivity, K_fs, is highly variable. Therefore, interpreting and simulating hydrological processes, such as rainfall excess generation, need a large number of K_fs data even at the plot scale. Simple and reasonably rapid experiments should be carried out in the field. In this investigation, a simple infiltration experiment with a ring inserted shortly into the soil and the estimation of the so‐called α* parameter allowed to obtain an approximate measurement of K_fs. The theoretical approach was tested with reference to 149 sampling points established on Burundian soils. The estimated K_fs with the value of first approximation of α* for most agricultural field soils (α* = 0.012 mm^?1) differed by a practically negligible maximum factor of two from the saturated conductivity obtained by the complete Beerkan Estimation of Soil Transfer parameters (BEST) procedure for soil hydraulic characterization. The measured infiltration curve contained the necessary information to obtain a site‐specific prediction of α*. The empirically derived α* relationship gave similar results for K_fs (mean = 0.085 mm s^?1; coefficient of variation (CV) = 71%) to those obtained with BEST (mean = 0.086 mm s^?1; CV = 67%), and it was also successfully tested with reference to a few Sicilian sampling points, since it yielded a mean and a CV of K_fs (0.0094 mm s^?1 and 102%, respectively) close to the values obtained with BEST (mean = 0.0092 mm s^?1; CV = 113%). The developed method appears attractive due to the extreme simplicity of the experiment. Copyright © 2012 John Wiley & Sons, Ltd.     

Using a transient infiltrometric technique for intensively sampling field‐saturated hydraulic conductivity of a clay soil in two runoff plots

The point measurement of soil properties allows to explain and simulate plot scale hydrological processes. An intensive sampling was carried out at the surface of an unsaturated clay soil to measure, on two adjacent plots of 4 × 11 m² and two different dates (May 2007 and February–March 2008), dry soil bulk density, ρ_b, and antecedent soil water content, θ_i, at 88 points. Field‐saturated soil hydraulic conductivity, K_fs, was also measured at 176 points by the transient Simplified Falling Head technique to determine the soil water permeability characteristics at the beginning of a possible rainfall event yielding measurable runoff. The ρ_b values did not differ significantly between the two dates, but wetter soil conditions (by 31%) and lower conductivities (1.95 times) were detected on the second date as compared with the first one. Significantly higher (by a factor of 1.8) K_fs values were obtained with the 0.30‐m‐diameter ring compared with the 0.15‐m‐diameter ring. A high K_fs (> 100 mm h^?1) was generally obtained for low θ_i values (< 0.3 m³m^?3), whereas a high θ_i yielded an increased percentage of low K_fs data (1–100 mm h^?1). The median of K_fs for each plot/sampling date combination was not lower than 600 mm h^?1, and rainfall intensities rarely exceeded 100 mm h^?1 at the site. The occurrence of runoff at the base of the plot needs a substantial reduction of the surface soil permeability characteristics during the event, probably promoted by a higher water content than the one of this investigation (saturation degree = 0.44–0.62) and some soil compaction due to rainfall impact. An intensive soil sampling reduces the risk of an erroneous interpretation of hydrological processes. In an unstable clay soil, changes in K_fs during the event seem to have a noticeable effect on runoff generation, and they should be considered for modeling hydrological processes. Copyright © 2012 John Wiley & Sons, Ltd.     

Fire decreases near‐surface hydraulic conductivity and macropore flow in blanket peat

Many peatlands have been subjected to wildfire or prescribed burning, but it is not known how these fires influence near‐surface hydrological processes. Macropores are important flowpaths in the upper layers of blanket peat and were investigated through the use of tension disc infiltrometers, which also provide data on saturated hydraulic conductivity. Measurements were performed on unburnt peat (U), where prescribed burning had taken place 2 years (B2), 4 years (B4) and >15 (B15+) years prior to sampling, and where a wildfire (W) had taken place 4 months prior to sampling. Where there had been recent burning (B2, B4 and W), saturated hydraulic conductivity was approximately three times lower than where there was no burning (U) or where burning was last conducted >15 years ago (B15+). Similarly, the contribution of macropore flow to overall infiltration was significantly lower (between 12% and 25% less) in the recently burnt treatments compared to B15+ and U. There were no significant differences in saturated hydraulic conductivity or macropore flow between peat that had been subject to recent wildfire (W) and those that had undergone recent prescribed burning (B2 and B4). The results suggest that fire influences the near‐surface hydrological functioning of peatlands but that recovery in terms of saturated hydraulic conductivity and macropore flow may be possible within two decades if there are no further fires. Copyright © 2013 John Wiley & Sons, Ltd.     

A field‐scale infiltration model accounting for spatial heterogeneity of rainfall and soil saturated hydraulic conductivity

This study first explores the role of spatial heterogeneity, in both the saturated hydraulic conductivity K_s and rainfall intensity r, on the integrated hydrological response of a natural slope. On this basis, a mathematical model for estimating the expected areal‐average infiltration is then formulated. Both K_s and r are considered as random variables with assessed probability density functions. The model relies upon a semi‐analytical component, which describes the directly infiltrated rainfall, and an empirical component, which accounts further for the infiltration of surface water running downslope into pervious soils (the run‐on effect). Monte Carlo simulations over a clay loam soil and a sandy loam soil were performed for constructing the ensemble averages of field‐scale infiltration used for model validation. The model produced very accurate estimates of the expected field‐scale infiltration rate, as well as of the outflow generated by significant rainfall events. Furthermore, the two model components were found to interact appropriately for different weights of the two infiltration mechanisms involved. Copyright © 2005 John Wiley & Sons, Ltd.     

Impacts of successive wildfire on soil hydraulic properties: Implications for debris flow hazards and system resilience

Climate and land use changes have led to recent increases in fire size, severity, and/or frequency in many different geographic regions and ecozones. Most post-wildfire geomorphology studies focus on the impact of a single wildfire but changing wildfire regimes underscore the need to quantify the effects of repeated disturbance by wildfire and the subsequent impacts on system resilience. Here, we examine the impact of two successive wildfires on soil hydraulic properties and debris flow hazards. The 2004 Nuttall-Gibson Complex and the 2017 Frye Fire affected large portions of the Pinaleño Mountains in southern Arizona, creating a mosaic of burn severity patterns that allowed us to quantify differences in wildfire-induced hydrologic changes as a function of burn severity and recent fire history (i.e. burned in only the Frye Fire or burned in both fires). Field observations after the 2017 Frye Fire indicated debris flow activity in areas burned predominantly at low severity. Many of these areas, however, were also affected by the 2004 Nuttall-Gibson Complex, suggesting that the relatively short recovery time between the two wildfires may have played a role in the geomorphic response to the most recent wildfire. Field measurements of soil hydraulic properties suggest that soils burned at moderate severity in 2004 and low severity in 2017 have a lower infiltration capacity relative to those that remained unburned in 2004 and burned at low severity in 2017. Simulations of runoff demonstrate that measured differences in infiltration capacity between once- and twice-burned soils are sufficient in some cases to influence the rainfall intensities needed to initiate runoff generated debris flows. Results quantify the impact of wildfire history and burn severity on runoff and debris flow activity in a landscape affected by successive wildfires and provide insight into how the resilience of geomorphic systems may be affected by successive wildfires. © 2019 John Wiley & Sons, Ltd.     

Synergistic effects of water repellency and macropore flow on the hydraulic conductivity of a burned forest soil,south‐east Australia

Research shows that water repellency is a key hydraulic property that results in reduced infiltration rates in burned soils. However, more work is required in order to link the hydrological behaviour of water repellent soils to observed runoff responses at the plot and hillslope scale. This study used 5 M ethanol and water in disc infiltrometers to quantify the role of macropore flow and water repellency on spatial and temporal infiltration patterns in a burned soil at plot (<10 m²) scale in a wet eucalypt forest in south‐east Australia. In the first summer and winter after wildfire, an average of 70% and 60%, respectively, of the plot area was water repellent and did not contribute to infiltration. Macropores (r > 0·5 mm), comprising just 5·5% of the soil volume, contributed to 70% and 95%, respectively, of the field‐saturated and ponded hydraulic conductivity (K_p). Because flow occurred almost entirely via macropores in non‐repellent areas, this meant that less than 2·5% of the soil surface effectively contributed to infiltration. The hydraulic conductivity increased by a factor of up to 2·5 as the hydraulic head increased from 0 to 5 mm. Due to the synergistic effect of macropore flow and water repellency, the coefficient of variation (CV) in K_p was three times higher in the water‐repellent soil (CV = 175%) than under the simulated non‐repellent conditions (CV = 66%). The high spatial variability in K_p would act to reduce the effective infiltration rate during runoff generation at plot scale. Ponding, which tend to increase with increasing scale, activates flow through macropores and would raise the effective infiltration rates at larger scales. Field experiments designed to provide representative measurements of infiltration after fire in these systems must therefore consider both the inherent variability in hydraulic conductivity and the variability in infiltration caused by interactions between surface runoff and hydraulic conductivity. Copyright © 2010 John Wiley & Sons, Ltd.     

Synthesis of soil‐hydraulic properties and infiltration timescales in wildfire‐affected soils

We collected soil‐hydraulic property data from the literature for wildfire‐affected soils, ash, and unburned soils. These data were used to calculate metrics and timescales of hydrologic response related to infiltration and surface runoff generation. Sorptivity (S) and wetting front potential (Ψ_f) were significantly different (lower) in burned soils compared with unburned soils, whereas field‐saturated hydraulic conductivity (K_fs) was not significantly different. The magnitude and duration of the influence of capillarity during infiltration was greatly reduced in burned soils, causing faster ponding times in response to rainfall. Ash had large values of S and K_fs but moderate values of Ψ_f, compared with unburned and burned soils, indicating ash has long ponding times in response to rainfall. The ratio of S²/K_fs was nearly constant (~100 mm) for unburned soils but more variable in burned soils, suggesting that unburned soils have a balance between gravity and capillarity contributions to infiltration that may depend on soil organic matter, whereas in burned soils the gravity contribution to infiltration is greater. Changes in S and K_fs in burned soils act synergistically to reduce infiltration and accelerate and amplify surface runoff generation. Synthesis of these findings identifies three key areas for future research. First, short timescales of capillary influences on infiltration indicate the need for better measurements of infiltration at times less than 1 min to accurately characterize S in burned soils. Second, using parameter values, such as Ψ_f, from unburned areas could produce substantial errors in hydrologic modeling when used without adjustment for wildfire effects, causing parameter compensation and resulting underestimation of K_fs. Third, more thorough measurement campaigns that capture soil‐structural changes, organic matter impacts, quantitative water repellency trends, and soil‐water content along with soil‐hydraulic properties could drive the development of better techniques for numerically simulating infiltration in burned areas.     

Local‐scale variability of seepage and hydraulic conductivity in a shallow gravel‐bed river

Seepage rate and direction measured with a seepage metre modified for use in flowing water were greatly variable along a 300‐m reach of a shallow, gravel‐bed river and depended primarily on the local‐scale bed topography. The median value of seepage measured at 24 locations was 24 cm/day, but seepage measured at specific sites ranged from ?340 to +237 cm/day. Seepage also varied substantially over periods of hours to days and occasionally reversed direction in response to evolution of the sediment bed. Vertical hydraulic conductivity was related to seepage direction and was larger during upward seepage than during downward seepage; with differences ranging from 4 to 40% in areas of active sediment transport to more than an order of magnitude in areas where current was too slow to mobilize bed sediment. Seepage was poorly related to hydraulic gradient measured over vertical distances of 0·3 m and appeared to be opposite the hydraulic gradient at 18% of the locations where both parameters were measured. Results demonstrate the scale dependence of these measurements in coarse‐grained hyporheic settings and indicate that hydraulic gradients should be determined over a much shorter vertical increment if used to indicate exchange across the sediment–water interface. Published in 2009 by John Wiley & Sons, Ltd.     

Modelling effects of spatial variability of saturated hydraulic conductivity on autocorrelated overland flow data: linear mixed model approach

The mixed linear model approach was introduced and applied in studying the effects of spatial variation of the saturated hydraulic conductivity (K _s ) on the variation of the overland flow. Analysis was carried out with 2,000 rainfall-runoff events, all generated through transformation of real, observed rainfall events and different spatially variable K _s fields in a small (12 ha) agricultural catchment. The parameters accounting for the variation in the generation method were the coefficient of variation (cv) and correlation length (L _x L _y ) of K _s both having two levels of values obtained from field measurements of other studies. The analysis showed that the combinations with both parameters having the smaller or bigger value during flow peaks only caused different response in the overland flow. However, the parameters were statistically significant only at the 10% level. Most of the flow variation was explained by the event dynamics. The mixed models were able to model the structure of the data efficiently with less restrictive assumptions than for example the analysis of variance, hence producing more reliable results. The method was able to take into account autocorrelation of the test series, correlation between the factors and unequal variances. The usefulness of the method was supported by the fact that the conclusions drawn by it were confirmed by simple, conventional methods of a previous study, added with statistical criteria and confidence levels for each calculation moment. The findings of the study can be utilized in practise for example when designing the field sampling experiments.     

Effects of initial soil water content and saturated hydraulic conductivity variability on small watershed runoff simulation using LISEM

Abstract

Soil water content (θ) and saturated hydraulic conductivity (K_s) vary in space. The objective of this study was to examine the effects of initial soil water content (θ_i) and K_s variability on runoff simulations using the LImburg Soil Erosion Model (LISEM) in a small watershed in the Chinese Loess Plateau, based on model parameters derived from intensive measurements. The results showed that the total discharge (TD) and peak discharge (PD) were underestimated when the variability of θ_i and K_s was partially considered or completely ignored compared with those when the variability was fully considered. Time to peak (TP) was less affected by the spatial variability compared to TD and PD. Except for TP in some cases, significant differences were found in all hydrological variables (TD, PD and TP) between the cases in which spatial variability of θ_i or K_s was fully considered and those in which spatial variability was partially considered or completely ignored. Furthermore, runoff simulations were affected more strongly by K_s variability than by θ_i variability. The degree of spatial variability influences on runoff simulations was related to the rainfall pattern and θ_i. Greater rainfall depth and instantaneous rainfall intensity corresponded to a smaller influence of the spatial variability. Stronger effects of the θ_i variability on runoff simulation were found in wetter soils, while stronger effects of the K_s variability were found in drier soils. For accurate runoff simulation, the θ_i variability can be completely ignored in cases of a 1-h duration storm with a return period greater than 10 years, while K_s variability should be fully considered even in the case of a 1-h duration storm with a return period of 20 years.

Editor D. Koutsoyiannis; Associate editor A. Fiori     

Sensitivity analysis of hydraulic conductivity and Manning's n parameters lead to new method to scale effective hydraulic conductivity across model resolutions

Hydrological modelling is an important tool for research, policy, and management, but uncertainty remains about parameters transferability from field observations made at small scale to models at the catchment scale and larger. This uncertainty compels the need to develop parameter relationships that are translatable across scale. In this study, we compare the changes to modelled processes as resolution is coarsened from 100‐m to 1‐km in a topographically complex, 255‐km² Colorado River headwater catchment. We conducted a sensitivity analysis for hydraulic conductivity (K) and Manning's n parameters across four orders of magnitude. Results showed that K acts as a moderator between surface and subsurface contributions to streamflow, whereas n moderates the duration of high intensity, infiltration‐excess flow. The parametric sensitivity analysis informed development of a new method to scale effective hydraulic conductivity across modelling resolutions in order to compensate for the loss of topographic gradients as resolution is coarsened. A similar mathematical relationship between n and lateral resolution changes was not found, possibly because n is also sensitive to time discretization. This research provides an approach to translate hydraulic conductivity parameters from a calibrated coarse model to higher resolutions where the number of simulations are limited by computational demand.     

Using a pore‐scale model to quantify the effect of particle re‐arrangement on pore structure and hydraulic properties

A pore‐scale model based on measured particle size distributions has been used to quantify the changes in pore space geometry of packed soil columns resulting from a dilution in electrolyte concentration from 500 to 1 mmol l^?1 NaCl during leaching. This was applied to examine the effects of particle release and re‐deposition on pore structure and hydraulic properties. Two different soils, an agricultural soil and a mining residue, were investigated with respect to the change in hydraulic properties. The mining residue was much more affected by this process with the water saturated hydraulic conductivity decreasing to 0·4% of the initial value and the air‐entry value changing from 20 to 50 cm. For agricultural soil, there was little detectable shift in the water retention curve but the saturated hydraulic conductivity decreased to 8·5% of the initial value. This was attributed to localized pore clogging (similar to a surface seal) affecting hydraulic conductivity, but not the microscopically measured pore‐size distribution or water retention. We modelled the soil structure at the pore scale to explain the different responses of the two soils to the experimental conditions. The size of the pores was determined as a function of deposited clay particles. The modal pore size of the agricultural soil as indicated by the constant water retention curve was 45 µm and was not affected by the leaching process. In the case of the mining residue, the mode changed from 75 to 45 µm. This reduction of pore size corresponds to an increase of capillary forces that is related to the measured shift of the water retention curve. Copyright © 2007 John Wiley & Sons, Ltd.     

Anisotropy and depth‐related heterogeneity of hydraulic conductivity in a bog peat. I: laboratory measurements

Anisotropy and heterogeneity of hydraulic conductivity (K) are suspected of greatly affecting rates and patterns of ground‐water seepage in peats. A new laboratory method, termed here the modified cube method, was used to measure horizontal and vertical hydraulic conductivity (K_h and K_v) of 400 samples of bog peat. The new method avoids many of the problems associated with existing field and laboratory methods, and is shown to give relatively precise measurements of K. In the majority of samples tested, K_h was much greater than K_v, indicating that the bog peat was strongly anisotropic. Log₁₀K_h, log₁₀K_v, and log₁₀ (K_h/K_v) were found to vary significantly with depth, although none of the relationships was simple. We comment on the scale dependency of our measurements. Copyright © 2002 John Wiley & Sons, Ltd.     

Horizontal hydraulic conductivity of shallow streambed sediments and comparison with the grain‐size analysis results

Streambed horizontal hydraulic conductivity (K_h) has a substantial role in controlling exchanges between stream water and groundwater. We propose a new approach for determining K_h of the shallow streambed sediments. Undisturbed sediment samples were collected using tubes that were horizontally driven into streambeds. The sediment columns were analysed using a permeameter test (PT) on site. This new test approach minimizes uncertainties due to vertical flow in the vicinity of test tube and stream stage fluctuations in the computation of the K_h values. Ninety‐eight PTs using the new approach were conducted at eight sites in four tributaries of the Platte River, east‐central Nebraska, USA. The K_h values were compared with the nondirectional hydraulic conductivity values (K_g) determined from 12 empirical grain‐size analysis methods. The grain‐size analysis methods used the same sediment samples as K_h tests. Only two methods, the Terzaghi and Shepherd methods, yielded K_g values close to the K_h values. Although the Sauerbrei method produced a value relatively closer to K_h than other nine grain‐size analysis methods, the values from this method were not as reliable as the methods of Terzaghi and Shepherd due to the inconsistent fluctuation of the average estimates at each of the test sites. The Zunker, Zamarin, Hazen, Beyer, and Kozeny methods overestimated K_h, while the Slichter, US Bureau of Reclamation (USBR), Harleman, and Alyamani and Sen methods underestimated K_h. Any of these specific grain‐size methods might yield good estimates of streambed K_h at some sites, but give poor estimates at other sites, indicating that the relationship between K_g and K_h is significantly site dependent in our study. Copyright © 2011 John Wiley & Sons, Ltd.     

Development of probability distributions for urban hydrologic model parameters and a Monte Carlo analysis of model sensitivity

This paper proposes an approach to estimating the uncertainty related to EPA Storm Water Management Model model parameters, percentage routed (P_R) and saturated hydraulic conductivity (K_sat), which are used to calculate stormwater runoff volumes. The methodology proposed in this paper addresses uncertainty through the development of probability distributions for urban hydrologic parameters through extensive calibration to observed flow data in the Philadelphia collection system. The established probability distributions are then applied to the Philadelphia Southeast district model through a Monte Carlo approach to estimate the uncertainty in prediction of combined sewer overflow volumes as related to hydrologic model parameter estimation. Understanding urban hydrology is critical to defining urban water resource problems. A variety of land use types within Philadelphia coupled with a history of cut and fill have resulted in a patchwork of urban fill and native soils. The complexity of urban hydrology can make model parameter estimation and defining model uncertainty a difficult task. The development of probability distributions for hydrologic parameters applied through Monte Carlo simulations provided a significant improvement in estimating model uncertainty over traditional model sensitivity analysis. Copyright © 2013 John Wiley & Sons, Ltd.     

The effect of conservation practices in sloped croplands on soil hydraulic properties and root‐zone moisture dynamics

Rain‐induced erosion and short‐term drought are the two factors that limit the productivity of croplands in the red soil region of subtropical China. The objective of this study was to estimate the effects of conservation practices on hydraulic properties and root‐zone water dynamics of the soil. A 3‐year experiment was performed on a slope at Xianning. Four treatments were evaluated for their ability to reduce soil erosion and improve soil water conditions. Compared with no practices (CK) and living grass strips (GS), the application of polyacrylamide (PAM) significantly reduced soil crust formation during intense rainfall, whereas rice straw mulching (SM) completely abolished soil crust formation. The SM and PAM treatments improved soil water‐stable aggregates, with a redistribution of micro‐aggregates into macro‐aggregates. PAM and SM significantly increased the soil water‐holding capacity. These practices mitigated the degradation of the soil saturated hydraulic conductivity (Ks) during intense rainfalls. These methods increased soil water storage but with limited effects during heavy rainfalls in the wet period. In contrast, during the dry period, SM had the highest soil water storage, followed by PAM and CK. Grass strips had the lowest soil water storage because of the water uptake during the vigorous grass growth. A slight decline in the soil moisture resulted in a significant decrease in the unsaturated hydraulic conductivity (Ku) of the topsoil. Therefore, the hydraulic conductivity in the field is governed by soil moisture, and the remaining soil moisture is more important than improving soil properties to resist short‐term droughts. As a result, SM is the most effective management practice when compared with PAM and GS, although they all protect the soil hydraulic properties during wet periods. These results suggest that mulching is the best strategy for water management in erosion‐threatened and drought‐threatened red soils. Copyright © 2014 John Wiley & Sons, Ltd.     

Scale‐dependency of hydraulic conductivity: an example from Thorne Moor,a raised mire in South Yorkshire,UK

The hydraulic conductivity (K) of many low permeability materials is strongly scale‐dependent. In raised mires and other types of peat deposit the effects of features such as abandoned infilled ditches, root holes and localized woody material, cause K to be heterogeneous and scale‐dependent. Despite this, field measurements are routinely made using auger hole (slug) tests at the scale of only a few tens of centimetres. Such measurements are locally valid, but where the regional subsurface movement of water through peat bogs is simulated using groundwater models, typically at the scale of hundreds of metres, they give rise to a systematic underestimate of flows and an overprediction of water table elevations. Until now, techniques to obtain values at a scale sufficiently large to include the effects of localized features of higher permeability have not been applied routinely. Research at Thorne Moor, a large raised mire, demonstrates that the K of peat varies over several orders of magnitude when measured at different scales, using a variety of techniques. Laboratory and auger hole tests cannot be relied upon to provide results that represent the hydraulic conductivity of large expanses of peatland. This has significant implications for the management and long‐term restoration of peatlands where both regional and local control of water levels is crucial. For groundwater models to be used successfully to plan such schemes, it is essential to apply the K values relevant to the scale of the simulation. This paper describes and tests novel techniques, using ditches, for the derivation of K at large scales which overcome many of the problems that have been identified with conventional techniques and are capable of producing estimates that are appropriate to the application of physically based regional flow models. Copyright © 2004 John Wiley & Sons, Ltd.     

Comparing Beerkan infiltration tests with rainfall simulation experiments for hydraulic characterization of a sandy‐loam soil

Saturated soil hydraulic conductivity, K _s , data collected by ponding infiltrometer methods and usual experimental procedures could be unusable for interpreting field hydrological processes and particularly rainfall infiltration. The K _s values determined by an infiltrometer experiment carried out by applying water at a relatively large distance from the soil surface could however be more appropriate to explain surface runoff generation phenomena during intense rainfall events. In this study, a link between rainfall simulation and ponding infiltrometer experiments was established for a sandy‐loam soil. The height of water pouring for the infiltrometer run was chosen, establishing a similarity between the gravitational potential energy of the applied water, E _p , and the rainfall kinetic energy, E _k . To test the soundness of this procedure, the soil was sampled with the Beerkan estimation of soil transfer parameters procedure of soil hydraulic characterization and two heights of water pouring (0.03 m, i.e., usual procedure, and 0.34 m, yielding E _p  = E _k ). Then, a comparison between experimental steady‐state infiltration rates, i _sR , measured with rainfall simulation experiments determining runoff production and K _s values for the two water pouring heights was carried out in order to discriminate between theoretically possible (i _sR  ≥ K _s ) and impossible (i _sR  < K _s ) situations. Physically possible K _s values were only obtained by applying water at a relatively large distance from the soil surface, because i _sR was equal to 20.0 mm h^?1 and K _s values were 146.2–163.9 and 15.2–18.7 mm h^?1 for a height of water pouring of 0.03 and 0.34 m, respectively. This result suggested the consistency between Beerkan runs with a high height of water pouring and rainfall simulator experiments. Soil compaction and mechanical aggregate breakdown were the most plausible physical mechanisms determining reduction of K _s with height. This study demonstrated that the height from which water is poured onto the soil surface is a key parameter in infiltrometer experiments and can be adapted to mimic the effect of high intensity rain on soil hydraulic properties.