Storage of sediment‐associated heavy metals along the channelized Odra River,Poland

The importance of long‐term storage of heavy metals in groyne fields, functioning over 150 years, is investigated for the River Odra (Oder), western Poland. Construction of groynes along the Odra preceded rapid development of heavy industrialization in the largest coal mine districts in Poland and the Czech Republic that resulted in persistent riverine pollution. The 187 km long Middle Odra reach was repeatedly channelized from the first half of the eighteenth century to the turn of the twentieth century, during which time partially filled groyne fields were dissected by new bank lines and groyne systems, with older groyne fields partially keyed into the floodplain. Consequently, concentrations of zinc, lead, cadmium, and copper within historically deposited groyne field sediments exceed local geochemical background levels by more than 60, 40, 15 and 10 times, respectively. Sediments contaminated with heavy metals occur within three distinctive geomorphic zones: zone I is up to 250 m wide and furthest from the present channel, comprising decimeter‐thick polluted sediments, overlying eighteenth century sand and gravel bars; zone II represents the former nineteenth century groyne fields, with widths between 10 and 100 m, filled with as much as 3 m of polluted sediments; zone III represents the twentieth century groyne fields, which are several to a dozen metres wide and filled with polluted sediments averaging depths of more than 2 m. This investigation indicates that large and extensive sediment quantities of moderately polluted sediments are stored immediately along the banks of the River Odra. These sediments could be a significant secondary pollution source and therefore careful maintenance of contemporary bank protection structures is required. Copyright © 2009 John Wiley & Sons, Ltd.     

Variations in sediment sources and yields in the Finger Lakes and Catskills regions of New York

The proportional contributions of stream bank and surface sources to fine sediment loads in watersheds in New York State were quantified with uncertainty analysis. Eroding streamside glacial drift, including glaciolacustrine deposits, were examined to help explain variations in the proportional contributions made by bank erosion. Sediment sources were quantified by comparing concentrations of the bomb‐derived radionuclide ¹³⁷Cs in fluvial sediment with sediment from potential source areas such as agricultural soils, forest soils and stream banks. To compare sediment sources in streams containing abundant deposits of fine‐grained glacial drift with watersheds that lacked moderate or extensive streamside deposits, samples were taken from 15 watersheds in the region. The mean contribution of bank erosion to sediment loads in the six streams with glaciolacustrine deposits was 60% (range 46–76%). The proportional contribution of bank erosion was also important in one stream lacking glaciolacustrine deposits (57%) but was less important in the remainder, with contributions ranging from 0 to 46%. Data from this study on the varying contributions of bank erosion and data from past studies of sediment yield in 15 watersheds of New York State suggest that eroding streamside glacial deposits dominate sediment yield in many watersheds. In other watersheds, past impacts to streams, such as channelization, have also resulted in high levels of bank erosion. Copyright © 2007 John Wiley & Sons, Ltd.     

Spatio-temporal characteristics of small-scale wave–current ripples on the Ameland ebb-tidal delta

Ebb-tidal deltas are highly dynamic environments affected by both waves and currents that approach the coast under various angles. Among other bedforms of various scales, these hydrodynamics create small-scale bedforms (ripples), which increase the bed roughness and will therefore affect hydrodynamics and sediment transport. In morphodynamic models, sediment transport predictions depend on the roughness height, but the accuracy of these predictors has not been tested for field conditions with strongly mixed (wave–current dominated) forcing. In this study, small-scale bedforms were observed in the field with a 3D Profiling Sonar at five locations on the Ameland ebb-tidal delta, the Netherlands. Hydrodynamic conditions ranged from wave dominated to current dominated, but were mixed most of the time. Small-scale ripples were found on all studied parts of the delta, superimposed on megaripples. Even though a large range of hydrodynamic conditions was encountered, the spatio-temporal variations in small-scale ripple dimensions were relatively small (height 0.015 m, length 0.11 m). Also, the ripples were always highly three-dimensional. These small dimensions are probably caused by the fact that the bed consists of relatively fine sediment. Five bedform height predictors were tested, but they all overestimated the ripple heights, partly because they were not created for small grain sizes. Furthermore, the predictors all have a strong dependence on wave- and current-related velocities, whereas the ripple heights measured here were only related to the near-bed orbital velocity. Therefore, ripple heights and lengths in wave–current-dominated, fine-grained coastal areas ( mm) may be best estimated by constant values rather than values dependent on the hydrodynamics. In the case of the Ameland ebb-tidal delta, these values were found to be m and m. ©2019 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd.     

Hydro‐meteorological drivers and sources of suspended sediment flux in the pro‐glacial zone of the retreating Castle Creek Glacier,Cariboo Mountains,British Columbia,Canada

Glaciers are major agents of erosion that increase sediment load to the downstream fluvial system. The Castle Creek Glacier, British Columbia, Canada, has retreated ~1.0 km in the past 70 years. Suspended sediment concentration (SSC) and streamflow (Q) were monitored independently at five sites within its pro‐glacial zone over a 60 day period from July to September 2011, representing part of the ablation season. Meteorological data were collected from two automatic weather stations proximal to the glacier. The time‐series were divided into hydrologic days and the shape and magnitude of the SSC response to hydro‐meteorological conditions (‘cold and wet’, ‘hot and dry’, ‘warm and damp’, and ‘storm’) were categorized using principal component analysis (PCA) and cluster analysis (CA). Suspended sediment load (SSL) was computed and summarized for the categories. The distribution of monitoring sites and results of the multivariate statistical analyses describe the temporal and spatial variability of suspended sediment flux and the relative importance of glacial and para‐glacial sediment sources in the pro‐glacial zone. During the 2011 study period, ~ 60% of the total SSL was derived from the glacial stream and sediment deposits proximal to the terminus of the glacier; during ‘storm’ events, that contribution dropped to ~40% as the contribution from diffuse and point sources of sediment throughout the pro‐glacial zone and within the meltwater channels increased. While ‘storm’ events accounted for just 3% of the study period, SSL was ~600% higher than the average over the monitoring period, and ~20% of the total SSL was generated in that time. Determining how hydro‐meteorological conditions and sediment sources control sediment fluxes will assist attempts to predict how pro‐glacial zones respond to future climate changes. Copyright © 2015 John Wiley & Sons, Ltd.     

Decadal trends and causes of sedimentation in the Inner Mongolia reach of the upper Yellow River,China

Using hydrological and sediment data, this study investigated decadal trends in sediment erosion/deposition in the Inner Mongolia reach of the upper Yellow River. The calculated yearly sediment erosion/deposition show that the reach was dominated by aggradation, degradation, and aggradation successively in three periods with the years around 1961 and 1987 as break‐points. By constructing relations between water discharge and sediment load, the contributions of key factors to the changes in sediment erosion/deposition in the reach were quantified. Results show that the sediment retention behind the main stem dams, the increase of natural runoff, and the decrease of sediment inputs from tributaries and upstream watershed were the main factors causing the transition from aggradation during 1955–1961 to degradation during 1962–1987. The reduction of natural runoff, the decrease of sediment retention behind dams, and the rise of sediment supply from tributaries were the key causes of the reversal from degradation in 1962–1987 to aggradation in 1988–2003. Water diversion has played an important role in the long‐term aggradation of the Inner Mongolia reach. The main stem dams had functioned to alleviate siltation after 1961, but their effects on siltation reduction had been gradually diminishing since the 1990s. Copyright © 2015 John Wiley & Sons, Ltd.     

Erosion,transport and deposition of a sediment replenishment under flood conditions

River reaches downstream of dams with constant residual discharge often lack sediment supply and periodic high flows due to dam sediment retention and flow regulation, respectively. To test a novel multi-deposit methodology for defining environmental flows for activating the dynamics of the river morphology downstream of dams, a flood was released from Rossens Dam in Switzerland. This event was combined for the first time with a multi-deposit configuration of sediment replenishment consisting of four artificial deposits allocated as alternate bars along the riverbanks as a restoration measure. To validate the sediment transport behaviour observed in laboratory tests, stones were equipped with radiofrequency identification (RFID) passive integrated transponder (PIT) tags, a fixed antenna was installed at the river bed and a mobile antenna was used to enable the investigation of the erosion, transport and deposition of replenished sediments. The duration of the erosion period was determined for the tracked stones, and average transport velocities were found to be on the order of 10^–3 m/s. To estimate the erosion efficiency of the flood, defined as the eroded tagged stones compared with the released water volume, the hydrograph was divided into different periods: rising limb, constant peak discharge, decreasing limb. During the rising limb of the flood, which lasted for 20% of the total flood duration, more than 40% of the PIT tags were transported. The defined erosion efficiency is a measure to support the hydrographic design of artificial flood releases from dams. The deposition of tagged stones resulted in a repeating cluster formation, as expected from previous laboratory experiments, creating an increase in hydraulic habitat diversity. Comparison of the results obtained in the field and from laboratory experiments confirmed the robustness of the multi-deposit sediment replenishment method. Combined with the knowledge gained on the erosion efficiency, these results could motivate further applications and research into multi-deposit sediment replenishment techniques as a habitat-oriented river restoration measure. © 2020 John Wiley & Sons, Ltd.     

Causes for the decline of suspended‐sediment discharge in the Mississippi River system, 1940–2007

Before 1900, the Missouri–Mississippi River system transported an estimated 400 million metric tons per year of sediment from the interior of the United States to coastal Louisiana. During the last two decades (1987–2006), this transport has averaged 145 million metric tons per year. The cause for this substantial decrease in sediment has been attributed to the trapping characteristics of dams constructed on the muddy part of the Missouri River during the 1950s. However, reexamination of more than 60 years of water‐ and sediment‐discharge data indicates that the dams alone are not the sole cause. These dams trap about 100–150 million metric tons per year, which represent about half the decrease in sediment discharge near the mouth of the Mississippi. Changes in relations between water discharge and suspended‐sediment concentration suggest that the Missouri–Mississippi has been transformed from a transport‐limited to a supply‐limited system. Thus, other engineering activities such as meander cutoffs, river‐training structures, and bank revetments as well as soil erosion controls have trapped sediment, eliminated sediment sources, or protected sediment that was once available for transport episodically throughout the year. Removing major engineering structures such as dams probably would not restore sediment discharges to pre‐1900 state, mainly because of the numerous smaller engineering structures and other soil‐retention works throughout the Missouri–Mississippi system. Published in 2009 by John Wiley & Sons, Ltd.     

Influence of storm-related sediment storage on the sediment delivery from tributary catchments in the upper Waipaoa River,New Zealand

Although much is known about overall sediment delivery ratios for catchments as components of sediment production and sediment yield, little is known about the component of temporary sediment storage. Sediment delivery ratios focused on the influence of storm-related sediment storage are measured at Matakonekone and Oil Springs tributaries of the Waipaoa River basin, east coast of New Zealand. The terrace deposits of both tributaries show abundant evidence of storm-related sedimentation, especially sediment delivered from Cyclone Bola, a 50 year return rainfall event which occurred in 1988. The sediment delivery ratio is calculated by dividing the volume of sediment transported from a tributary to the main stream by the volume of sediment generated at erosion sites in the tributary catchment. Because the sediment delivery volume is unknown, it can be calculated as the difference between sediment generation volume and sediment storage volume in the channel reach of the tributary. The volume of sediment generated from erosion sites in each tributary catchment was calculated from measurements made on aerial photographs dating from 1960 (1:44 000) and 1988 (1:27 000). The volume of sediment stored in the tributary can be calculated from measurements of cross-sections located along the tributary channel, which are accompanied by terrace deposits dated by counting annual growth rings of trees on terrace surfaces. Sediment delivery ratios are 0·93 for both Matakonekone catchment and Oil Springs catchment. Results indicate that Oil Springs catchment has contributed more than twice the volume of sediment to the Waipaoa River than the Matakonekone catchment (2·75 × 10⁶ m³ vs 1·22 × 10⁶ m³). Although large volumes of sediment are initially deposited during floods, subsequent smaller flows scour away much of these deposits. The sediment scouring rate from storage is 1·25 × 10⁴ m³ a⁻¹ for Matakonekone stream and 0·83 × 10⁴ m³ a⁻¹ for Oil Springs stream. Matakonekone and Oil Springs channels respond to extreme storms by instantaneously aggrading, then gradually excavating the temporarily stored sediment. Results from Matakonekone and Oil Springs streams suggest a mechanism by which event recurrence interval can strongly influence the magnitude of a geomorphic change. Matakonekone stream with its higher stream power is expected to excavate sediment deposits more rapidly and allow more rapid re-establishment of storage capacity. Copyright © 1999 John Wiley & Sons, Ltd.     

Starved versus alluvial river bedforms: an experimental investigation

Laboratory experiments were conducted to investigate the formation of river bedforms under sediment supply-limited conditions, i.e. when a motionless substratum is bared by the dynamics of the mobile sediments. Three series of experiments were organized in a laboratory flume by fixing all the hydrodynamic and morphodynamic parameters but varying the thickness of the initial layer of mobile sediments which covers the rigid bottom of the flume. At the end of all the experiments, which lasted for the same amount of time, the formation of transverse sand dunes was observed. For decreasing , the rigid bottom of the flume was bared progressively earlier during the experiment and the measurements showed a clear tendency of the bedforms to lengthen, i.e. to increase their crest-to-crest distance. Moreover, under strong supply limitation, the two-dimensional transverse dunes turned into three-dimensional barchanoid forms and into isolated barchan dunes characterized by an abrupt reduction in bedform heights. A two-dimensional Fourier analysis of the bottom profile was performed, providing the amplitude of the main streamwise and spanwise harmonic components of the bottom morphology as a function of . © 2019 John Wiley & Sons, Ltd.     

Postglacial sediment budget of Chilliwack Valley,British Columbia

The paraglacial reworking of glacial sediments by rivers and mass wasting is an important conditioning factor for modern sediment yields in mountainous catchments in formerly glaciated regions. Catchment scale and patterns of sediment storage are important influences in the rate of postglacial adjustment. We develop a quantitative framework to estimate the volume, sediment type, and fractional size distribution of legacy glacial materials in a large (1230 km²) watershed in the North Cascade Mountains in south‐western British Columbia, Canada. Chilliwack Valley is exceptional because of the well‐dated bounds of deglaciation. Interpolation of paleo‐surfaces from partially eroded deposits in the valley allows us to estimate the total evacuated sediment volume. We present a chronology of sediment evacuation from the valley and deposition in the outlet fan, based on infrared stimulated luminescence (IRSL) and ¹⁴ C dating of river terraces and fan strata, respectively. The effects of paraglacial sedimentation in Chilliwack Valley were intensified through a major fall in valley base‐level following ice retreat. The steepened mainstem valley gradient led to deep incision of valley fills and fan deposits in the lower valley network. The results of this integrated study provide a postglacial chronology and detailed sediment budget, accounting for long‐term sorting of the original sediments, lag deposit formation in the mainstem, deposition in the outlet fan, and approximate downstream losses of suspended sediment and wash load. The mass balance indicates that a bulk volume of approximately 3.2 km³ of glacial material has been evacuated from the valley. Copyright © 2012 John Wiley & Sons, Ltd.     

Erosion-control mechanism of sediment check dams on the Loess Plateau

Severe soil erosion occurs on the Loess Plateau in China, which makes the Yellow River the most sediment-laden river in the world. Construction of about 60,000 sediment check dams has remarkably controlled soil erosion on the Loess Plateau and reduced the sediment load of the middle and lower Yellow River. Nonetheless, little is known about the mechanism of erosion control and vegetation development of sediment check dams. The function of a single check dam mainly is trapping sediment, while the function of a train of check dams comprising dozens of or over hundreds of check dams in a gully encompasses controlling bed incision and reducing erosion energy. A formula was proposed to calculate the potential energy of bank failure and slope failure in a gully, which essentially constitutes the erosion energy. The erosion energy increases when gully incision occurs, which is induced by the incision of the Yellow River and its tributaries on the Loess Plateau. Sediment deposition in many gullies due to construction of check dams reduces the erosion energy to almost zero, which in turn greatly reduces soil erosion and sediment yield. Construction of check dams promotes vegetation development. The vegetation-erosion dynamics model was used to study the effect of check dams on vegetation development. Simulation results show that reforestation without check dam construction might result in an increase of vegetation cover in the first ten years and then a drop of vegetation cover to less than 10% in the later years. The check dams provide a foundation for vegetation development.     

Variation in the sediment deposition behind check‐dams under different soil erosion conditions on the Loess Plateau,China

To maintain a reasonable sediment regulation system in the middle reaches of the Yellow River, it is critical to determine the variation in sediment deposition behind check‐dams for different soil erosion conditions. Sediment samples were collected by using a drilling machine in the Fangta watershed of the loess hilly–gully region and the Manhonggou watershed of the weathered sandstone hilly–gully (pisha) region. On the basis of the check‐dam capacity curves, the soil bulk densities and the couplet thickness in these two small watersheds, the sediment yields were deduced at the watershed scale. The annual average sediment deposition rate in the Manhonggou watershed (702.0 mm/(km²·a)) from 1976 to 2009 was much higher than that in the Fangta watershed (171.6 mm/(km²·a)) from 1975 to 2013. The soil particle size distributions in these two small watersheds were generally centred on the silt and sand fractions, which were 42.4% and 50.7% in the Fangta watershed and 60.6% and 32.9% in the Manhonggou watershed, respectively. The annual sediment deposition yield exhibited a decreasing trend; the transition years were 1991 in the Fangta watershed and 1996 in the Manhonggou watershed (P < 0.05). In contrast, the annual average sediment deposition yield was much higher in the Manhonggou watershed (14011.1 t/(km²·a)) than in the Fangta watershed (3149.6 t/(km²·a)). In addition, the rainfalls that induced sediment deposition at the check‐dams were greater than 30 mm in the Fangta watershed and 20 mm in the Manhonggou watershed. The rainfall was not the main reason for the difference in the sediment yield between the two small watersheds. The conversion of farmland to forestland or grassland was the main reason for the decrease in the soil erosion in the Fangta watershed, while the weathered sandstone and bare land were the main factors driving the high sediment yield in the Manhonggou watershed. Knowledge of the sediment deposition process of check‐dams and the variation in the catchment sediment yield under different soil erosion conditions can serve as a basis for the implementation of improved soil erosion and sediment control strategies, particularly in semi‐arid hilly–gully regions. Copyright © 2018 John Wiley & Sons, Ltd.     

A revised soil erosion budget for India: role of reservoir sedimentation and land‐use protection measures

Among the different controls of erosion budget at basin level, the relative impact of dams and land management is yet to be investigated. In this paper, the impact of dams on sediment yield has been assessed by using a conceptual modelling framework which considers the gross erosion and the cascade of dams constructed on a river network. The sediment budget has been estimated based on the gross erosion, deposition of sediment in reservoirs, and sediment yields of 23 mainland river basins of India. The gross erosion of the country is estimated as 5.11 ± 0.4 Gt yr^?1 or 1559 t km^?2 yr^?1, out of which 34.1 ± 12% of the total eroded soil is deposited in the reservoirs, 22.9 ± 29% is discharged outside the country (mainly to oceans), and the remaining 43.0 ± 41% is displaced within the river basins. The river basins of northern India contribute about 81% of the total sediment yield from landmass while the share of southern river basins is 19%. The components of revised sediment budget for India are prominently influenced by the sediment trapped in reservoirs and the treatment of catchment areas by soil and water conservation measures. Analysis of sediment deposition in 4937 reservoirs indicated the average annual percentage capacity loss as 1.04% though it varies from 0.8% to >2% per year in smaller dams (1–50 Mm³ capacity) and from <0.5% to 0.8% per year in larger dams (51 to >1000 Mm³ capacity). Siltation of smaller dams poses a serious threat to their ecosystem services as they cater to a wider population for domestic, agricultural, and industrial purposes. Amongst the environment controls, land use significantly impacts the gross erosion rate and specific sediment yield as compared to climatic and topographic parameters. However, to analyse their integrated effect on the complex processes of sediment fluxes in a basin, further research efforts are needed. Copyright © 2016 John Wiley & Sons, Ltd.     

Large landslides and their effect on sediment flux in South Westland,New Zealand

Landslides and runoff are dominant erosional agents in the tectonically active alpine South Westland area of New Zealand, characterized by high uplift rates and extreme orographic precipitation. Despite a high density of shallow debris slides and flows, the geomorphic imprints of deep‐seated bedrock failures are dominant and persistent. Over 50 large (>1 km²) landslides comprising rock slide[sol ]avalanches, complex rotational and rock‐block slides, wedge failures, and deep‐seated gravitational slope deformation were detected on air photos and shaded‐relief images. Major long‐term impacts on alpine rivers include (1) forced alluviation upstream of landslide dams, (2) occlusion of gorges and triggering of secondary riparian landslides, and (3) diversion of channels around deposits to form incised meandering gorges. Remnants of large prehistoric (i.e. pre‐1840) landslide deposits possibly represent the low‐frequency (in terms of total area affected yet dominant) end of the spectrum of mass wasting in the western Southern Alps. This is at odds with high erosion rates in an active erosional landscape. Large landslides appear to have dual roles of supplying and retaining sediment. The implications of these roles are that (1) previous models of (shallow) landslide‐derived sediment flux need to be recalibrated, and (2) geomorphic effects of earthquake‐induced landsliding may persist for at least 10² years. Copyright © 2005 John Wiley & Sons, Ltd.     

Does variable channel morphology lead to dynamic salmon habitat?

Stream channel morphology forms the template upon which hydraulic aspects of aquatic habitat are created, yet spatial and temporal variability in habitat imposed by changing morphology is not well understood. This paper presents a conceptual model linking sediment supply patterns to spatial and temporal variability in channel form and aquatic habitat. To evaluate this model, change over time in three habitat variables is quantified using a 2D hydrodynamic modeling approach. A 45-year record of topographic data from Carnation Creek, a catchment in coastal British Columbia, is used for the flow modeling. Using the Nays2DH modeling platform, water depths and velocities are simulated in eight channel segments located at different positions relative to locations of historical colluvial input using seven flow levels ranging from 3% to 400% of mean annual discharge (0.02 to 3.31 m s ). Results indicate that habitat availability changes through time as a result of sediment supply-driven changes to channel morphology and wood loads, but patterns in habitat vary as a function of dominant channel segment morphology. Spatial and temporal variability in morphology also influences the relationship between habitat availability and river discharge, leading to non-stationary habitat-discharge rating curves. When habitat areas are predicted by applying these curves to daily flow series spanning annual dry seasons, over 50% of the variance in cumulative seasonal habitat area can be explained by year-to-year changes in channel morphology and wood loading, indicating that changing morphology is an important factor for driving temporal habitat variability. This variance is related to the morphological variability of a channel segment, which in turn is associated with the segment position relative to zones of colluvial input. Collectively, these results suggest that variability in habitat is impacted by channel morphology, and can be evaluated partly on the basis of a channel's sediment supply regime. © 2019 John Wiley & Sons, Ltd.     

The distribution and residence time of suspended sediment stored within the channel margins of a gravel‐bed bedrock river

Previously undocumented deposits are described that store suspended sediment in gravel‐bedded rivers, termed ‘fine‐grained channel margin’ (FGCM) deposits. FGCM deposits consist of sand, silt, clay, and organic matter that accumulate behind large woody debris (LWD) along the margins of the wetted perimeter of the single‐thread, gravel‐bed South River in Virginia. These deposits store a total mass equivalent to 17% to 43% of the annual suspended sediment load. Radiocarbon, ²¹⁰Pb and ¹³⁷C dating indicate that sediment in FGCM deposits ranges in age from 1 to more than 60 years. Reservoir theory suggests an average turnover time of 1·75 years and an annual exchange with the water column of a mass of sediment equivalent to 10% to 25% of the annual sediment load. The distribution of ages in the deposits can be fitted by a power function, suggesting that sediment stored in the deposits has a wide variety of transit times. Most sediment in storage is reworked quickly, but a small portion may remain in place for many decades. The presence of FGCM deposits indicates that suspended sediment is not simply transported downstream in gravel‐bed rivers in agricultural watersheds: significant storage can occur over decadal timescales. South River has a history of mercury contamination and identifying sediment sources and sinks is critical for documenting the extent of contamination and for developing remediation plans. FGCM deposits should be considered in future sediment budget and sediment transport modeling studies of gravel‐bed rivers in agricultural watersheds. Copyright © 2010 John Wiley & Sons, Ltd.     

Magnitude and variation in the contribution of bank erosion to the suspended sediment load of the River Severn,UK

The wide range of studies describing the role of bank erosion in fluvial sediment supply have mostly lumped amounts of bank erosion into coarse temporal units, such as years. This paper investigates sediment yields from individual bank erosion events within the upper River Severn, UK (basin area 380 km²). Manual erosion pins and photo-electronic erosion pins were used to estimate bank erosion, and turbidity meters were used to determine suspended sediment transport. At the annual time-scale, the silt-clay fraction of bank-derived sediment accounted for an equivalent of 17 per cent of the suspended load, increasing to an average of 38 per cent at the monthly timescale, and then to an average of 64 per cent at the event timescale. This research highlighted that for an upland catchment, bank erosion was an important supply of suspended sediment, and that for some flood events bank erosion can supply more sediment than is transported. © 1997 John Wiley & Sons, Ltd.     

Spatio‐temporal sedimentation patterns in beaver ponds along the Chevral river,Ardennes, Belgium

With the recovery of the European beaver (Castor fiber) and their capacity to engineer fluvial landscapes, questions arise as to how they influence sediment transport, including the spatio‐temporal trends and patterns of sedimentation in beaver ponds. The Chevral river (Ardennes, Belgium) contains two beaver dam sequences, which appeared in 2004. Volumes of sediment deposited behind the dams were measured, and grain‐size distribution patterns were determined. Flow discharges and sediment fluxes were measured at the inflow and outflow of each dam sequence. Between 2004 and 2011, 1710.1 m³ of sediment was deposited behind the beaver dams, with an average sediment thickness of 25.1 cm. The thickness of the sediment layer was significantly (p < 0.001) related to the area of the beaver ponds. Along the stream, beaver pond sediment thickness displayed a sinusoidal deposition pattern, in which ponds with thick sediment layers were preceded by a series of ponds with thinner sediment layers. A downstream textural coarsening in the dam sequences was also observed, probably because of dam failures subsequent to surges. Differences in sediment flux between the inflow and outflow at the beaver pond sequence were related to the river hydrograph, with deposition taking place during the rising limbs and slight erosion during the falling limbs. The 7‐year‐old sequences have filtered 190.19 ton of sediment out of the Chevral river, which is of the same order of magnitude as the 374.4 ton measured in pond deposits, with the difference between the values corresponding to beaver excavations (60.24 ton), inflow from small tributaries, and runoff from the valley flanks. Hydrogeomorphic effects of C. fiber and Castor canadensis activity are similar in magnitude. The detailed analysis of sedimentation in beaver pond sequences confirms the potential of beavers to contribute to river and wetland restoration, and catchment management. Copyright © 2013 John Wiley & Sons, Ltd.     

Post-fire management effects on sediment (dis)connectivity in Mediterranean forest ecosystems: Channel and catchment response

Forest fires and post-fire practices influence sediment connectivity (SC). In this study, we use the ‘aggregated index of connectivity’ (AIC) to assess SC in five Mediterranean catchments (198–1090 ha) affected by a wildfire in 2012 in south-eastern Spain. Two temporal scenarios were considered, immediately after the fire and before post-fire management, and 2 years after the fire including all practices (hillslope barriers, check-dams, afforestation, salvage logging and skid trails). One LiDAR (light detection and ranging)-derived digital elevation model (DEM, 2 m × 2 m resolution) was generated, per scenario. The five catchment outlets were established as the computation target (AIC_OUT), and structural and functional SC were calculated. Index outputs were normalized to make the results of the non-nested catchments comparable (AIC_N-OUT). The output analysis includes the SC distribution along the catchments and at local scale (929 sub-catchments, 677 in the burned area), the hillslope and channel measures' effect on SC, and a sedimentological analysis using observed area-specific sediment yield (SSY) at 10 new (built after post-fire practices) concrete check-dams located in the catchments (SSY = 1.94 Mg ha⁻¹ yr⁻¹; σ = 1.22). The catchments with more circular shapes and steeper slopes were those with higher AIC_N-OUT. The structural SC maps – removing the rainfall erosivity influence – allowed evaluating the actual role played by the post-fire practices that reduced SC ( $\overline{x}$= − 1.19%; σ = 0.41); while functional SC was linked to the actual change of SC ( $\overline{x}$= + 5.32%; σ = 0.62). Hillslope treatments resulted in significant changes on AIC_N-OUT at sub-catchment scale with certain disconnectivity. A good and positive correlation was found between the SSY and the changes of AIC_N-OUT. However, the coarse DEM resolution explained the lack of effect of the rock check-dams – located on the secondary channels – on AIC_N-OUT. AIC_N-OUT proved to be a useful tool for decision making in post-fire restoration, but an optimal input data is still necessary to refine calculations.     

Sediment retention by check dams in the Hekouzhen-Longmen Section of the Yellow River

Coarse sediment retention by check dams is analyzed for five typical catchments in the Hekou-Longmen section of the midstream of the Yellow River, which is an area of high .coarse sediment concentration. The catchments are the Huangfuchuan, Kuye, Wuding, Sanchuan and Qiushui River Basins. The amount of coarse sediment retained by check clams in these areas for different periods was measured. Sediment reduction due to check clams is compared with other soil conservation measures and the results show that check clams are the most effective to rapidly reduce the amount of coarse sediment entering the Yellow River. If the average percentage of the drainage area with check clams for the five typical catchments reaches 3.0%, the average sediment reduction ratio can reach 60%. Therefore, to rapidly and effectively reduce the amount of sediment, especially coarse sediment, entering the Yellow River, the area percentage of check clams in the Hekou-Longmen section should be kept around 3%. The Kuye and Huangfuchuan River Basins are the preferred main catchments in which such water conservation measures are implemented.