Elevation adjustments of paired natural levees during flooding of the Saskatchewan River

Natural levees control the exchange of water between an alluvial channel and its floodplain, but little is known about the spatial distribution and evolution of levee heights. The summer 2005 flood of the Saskatchewan River (Cumberland Marshes, east‐central Saskatchewan) inundated large areas of floodplain for up to seven weeks, forming prominent new deposits on natural levees along main‐stem channels. Measurements of flood‐deposit thickness and crest heights of 61 levee pairs show that the thickest deposits occur on the lower pre‐flood levee in 80% of the sites, though no clear relationship exists between deposit thickness and magnitude of height difference. Only 16% of the pairs displayed thicker deposits on the higher levee, half of which occurred at sites where relatively clear floodbasin waters re‐entered turbid channels during general flooding. Difference in crest elevation (ΔE) between paired levees is approximately log‐normally distributed, both before and after the flood, though with different mean values. Supplemental observations from tank experiments indicate that during near‐bankfull flows, temporally and spatially variable deposition and erosion occur on levees due to backwater effects associated with nearby channel bars and irregular rises of the channel bed forced by channel extension. During floods, preferential deposition in lows tends to even out crest heights. Copyright © 2009 John Wiley & Sons, Ltd.     

Morphology and dynamics of the intertidal floodplain along the Amazon tidal river

Depositional environments along the tidal river downstream of Óbidos have been proposed as important sinks for up to one third of the sediment discharge from the Amazon River. However, the morphology of the intertidal floodplain and the dynamics of sediment exchange along this reach have yet to be described. River-bank surveys in five regions along the Amazon tidal river reveal a distinct transition in bank morphology between the upper, central and lower reaches of the tidal river. The upper tidal-river floodplain is defined by prominent natural levees that control the transfer of water and sediment between the mainstem Amazon River and its floodplain. Greater tidal influence in the central tidal river suppresses levee development, and tidal currents increase sediment transport into the distal parts of the floodplain. In the lower tidal river, the floodplain morphology closely resembles marine intertidal environments (e.g. mud flats, salt marshes), with dendritic tidal channels incising elevated vegetated flats. Theory, morphology and geochronology suggest that the dynamics of sediment delivery to the intertidal floodplain of the Amazon tidal river vary along its length due to the relative influence and coupling of fluvial and tidal dynamics. © 2018 John Wiley & Sons, Ltd.     

The effect of tide on the hydrology and morphology of a freshwater river

How does river hydrology and morphology change due to tidal influence? We contend that this is a question of particular consequence to many earth surface disciplines, but one that has not been adequately addressed. Previous studies have relied on gradients in channel morphology and stratigraphy to infer energy regime of channels. However, in tidal rivers geomorphology influences the energy regime while the energy regime influences morphology; thus, geomorphic and stratigraphic patterns do not fully resolve the mechanisms which lead to change. We addressed this problem by comparing measurements of hydraulic energy and channel morphology along a tidal gradient to predictions of these characteristics in the absence of tides, and attributed the differences to tidal processes. Measurements of discharge, channel area, and energy dissipation (in kJ day^–1) were made over a 24·8 hour period at four sites spanning the non‐tidal to tidal freshwater Newport River, NC. We then predicted those characteristics under non‐tidal conditions using hydraulic geometry relationships and literature values from coastal plain rivers. Discharge was enhanced more than 10‐fold by tide, and this tidal effect increased from upstream to downstream along the tidal gradient. Cross‐sectional area increased three‐fold due to tide. Energy dissipation measured in the upper tidal river was four‐fold lower than predicted to occur in the absence of tide because tides decreased average velocity and discharge. Energy dissipation measured downstream was similar to that predicted to occur without tides, although there was large uncertainty in predicted values downstream. While this limited dataset does not permit us to make broad generalizations for definitive models, it does provide a proof‐of‐concept for a new approach to addressing a critical problem at the interface of fluvial and coastal morphology. Copyright © 2013 John Wiley & Sons, Ltd.     

Non-symmetrical levee breaching processes in a channel bend due to overtopping

A series of experiments were done to reveal the overtopping breaching process of non-cohesive and cohesive levees in a U-bend flume. The flood hydrograph and breaching geometry were measured and analyzed in detail. The results show that the levee breaching processes can be briefly divided into four stages: slope erosion, longitudinal headward gully-cutting, lateral erosion, and relative stabilization. For non-cohesive levees, non-symmetrical lateral development of the breach occurs throughout the four stages, and the final non-symmetrical coefficient is approximately 2.2–2.6. Larger flow discharge or higher water level can accelerate the breaching process, while coarser sands tend to accelerate the process initially but depress the process at the end. The fluvial erosion rate of a non-cohesive breach shows a power-function relation with the excess wall shear stress. For cohesive levees, a plateau forms in the breach partially blocking the flow in the first two stages. The breach flow is approximately perpendicular to the levee body, and, thus, the erosion rates of the two breach sides are almost the same. Non-symmetrical lateral development mainly occurs in the third stage when the deep gully forms. The final non-symmetrical coefficient is approximately 2.7–3.3. It is expected that these findings can provide a valuable experimental dataset and a theoretical basis for breach closure and flood alleviation.     

Mathematical modeling of flooding due to river bank failure

Modeling of flooding events resulting from bank overflooding and levee breaching is of relevant social and environmental interest. Two-dimensional (2D) hydrodynamic models integrating the shallow water equations turn out to be very effective tools for the purpose at hand. Many of the available models also use 1D channel elements, fully coupled to the 2D model, to simulate the flow of small channels dissecting the urban and rural areas, and 1D elements, referred to as 1D-links, to efficiently model the flow over levees, road and rail embankments, bunds, the flow through control gates, either free or submerged, and the operation of other hydraulic structures. In this work we propose a physically-based 1D-link to model breach formation and evolution in fluvial levees, and levee failure due to either piping or overtopping. The proposed 1D-link is then embedded in a 1D–2D hydrodynamic model, thus accounting for critical feedbacks between breach formation and changes in the hydrodynamic flow field. The breach model also includes the possibility of simulating breach closure, an important feature particularly in the view of hydraulic risk assessment and management of the emergency. The model is applied to five different case studies and the results of the numerical simulations compare favorably with field observations displaying a good agreement in terms of urban and rural flooded areas, water levels within the channel, final breach widths, and water volumes flowed through the breach.     

Tidal channel meander formation by depositional rather than erosional processes: examples from the prograding Skagit River Delta (Washington,USA)

Channel meander dynamics in fluvial systems and many tidal systems result from erosion of concave banks coupled with sediment deposition on convex bars. However, geographic information system (GIS) analysis of historical aerial photographs of the Skagit Delta marshes provides examples of an alternative meander forming process in a rapidly prograding river delta: deposition‐dominated tidal channel meander formation through a developmental sequence beginning with sandbar formation at the confluence of a blind tidal channel and delta distributary, proceeding to sandbar colonization and stabilization by marsh vegetation to form a marsh island opposite the blind tidal channel outlet, followed by narrowing of the gap between the island and mainland marsh, closure of one half of the gap to join the marsh island to the mainland, and formation of an approximately right‐angle blind tidal channel meander bend in the remaining half of the gap. Topographic signatures analogous to fluvial meander scroll bars accompany these planform changes. Parallel sequences of marsh ridges and swales indicate locations of historical distributary shoreline levees adjacent to filled former island/mainland gaps. Additionally, the location of marsh islands within delta distributaries is not random; islands are disproportionately associated with blind tidal channel/distributary confluences. Furthermore, blind tidal channel outlet width is positively correlated with the size of the marsh island that forms at the outlet, and the time until island fusion with mainland marsh. These observations suggest confluence hydrodynamics favor sandbar/marsh island development. The transition from confluence sandbar to tidal channel meander can take as little as 10 years, but more typically occurs over several decades. This depositional blind tidal channel meander formation process is part of a larger scale systemic depositional process of delta progradation that includes distributary elongation, gradient reduction, flow‐switching, shoaling, and narrowing. Copyright © 2010 John Wiley & Sons, Ltd.     

The anomalous tides near Broad Sound

Observations of tidal current and height, in conjunction with theoretical mathematical models are used to investigate the propagation of the tide near Broad Sound, a narrowing estuary situated on a wide section of continental shelf toward the southern end of the Great Barrier Reef. The observations indicate that the dense offshore reefs severely inhibit tidal flow, with the result that tides flood toward Broad Sound from the north and from the south, along the main lagoon. There is a local magnification of the semi-diurnal tides within Broad Sound itself.Models of flow across reefs confirm the effectiveness of dense, shallow, and broad reefs in acting as a barrier to the tide. The diffraction of tides through large gaps in the reef is modelled using conformal mapping techniques and with the inclusion of energy leakage, the diffraction model predicts magnification of the semi-diurnal tidal heights by a factor of about 4 and a phase lag of 3 h on the shelf near Broad Sound, these values being consistent with observation. The observed convergence of the tide close to, and within Broad Sound itself is consistent with the proximity of the semi-diurnal tidal period to the natural period for flow in Broad Sound, considered as a narrowing estuary. This results in further amplification, by an additional factor of about 1.5, so that the tides in Broad Sound are increased by a factor of between 5 and 6, altogether, compared with those elsewhere on the east Australian coast.     

The predictability of near-coastal currents using a baroclinic unstructured grid model

A limited domain, coastal ocean forecast system consisting of an unstructured grid model, a meteorological model, a regional ocean model, and a global tidal database is designed to be globally relocatable. For such a system to be viable, the predictability of coastal currents must be well understood with error sources clearly identified. To this end, the coastal forecast system is applied at the mouth of Chesapeake Bay in response to a Navy exercise. Two-day forecasts are produced for a 10-day period from 4 to 14 June 2010 and compared to real-time observations. Interplay between the temporal frequency of the regional model boundary forcing and the application of external tides to the coastal model impacts the tidal characteristics of the coastal current, even contributing a small phase error. Frequencies of at least 3 h are needed to resolve the tidal signal within the regional model; otherwise, externally applied tides from a database are needed to capture the tidal variability. Spatial resolution of the regional model (3 vs 1 km) does not impact skill of the current prediction. Tidal response of the system indicates excellent representation of the dominant M ₂ tide for water level and currents. Diurnal tides, especially K ₁, are amplified unrealistically with the application of coarse 27-km winds. Higher-resolution winds reduce current forecast error with the exception of wind originating from the SSW, SSE, and E. These winds run shore parallel and are subject to strong interaction with the shoreline that is poorly represented even by the 3-km wind fields. The vertical distribution of currents is also well predicted by the coastal model. Spatial and temporal resolution of the wind forcing including areas close to the shoreline is the most critical component for accurate current forecasts. Additionally, it is demonstrated that wind resolution plays a large role in establishing realistic thermal and density structures in upwelling prone regions.     

Revising the paradigm of tidal analysis – the uses of non-stationary data

Surface elevation and current records contain non-tidal variance, often dismissed as noise. The processes responsible for the non-tidal component may also modulate the tidal signal, altering its strength and frequency structure. Because of their manner of generation and propagation, internal tides are inherently irregular. The non-stationary character of these and other tidal processes provides an integral and useful property of tidal records, because it provides an opportunity to obtain insights into tidal dynamics and the interaction of tidal and non-tidal processes. It is, moreover, productive to use multiple approaches in analyzing coastal and estuarine tidal processes so that both the time-varying and average frequency content are determined. Only by confronting the causes of non-stationary behaviour in this way can some of the remaining challenges in tidal analysis and prediction be overcome, e.g. shelf and estuarine currents, river tides, internal tides, tide-surge interactions and tidally influenced ecological processes. Several examples illustrate the utility of non-stationary tidal analysis methods.Responsible Editor: Jens Kappenberg     

A simple approach to adjust tidal forcing in fjord models

To model currents in a fjord accurate tidal forcing is of extreme importance. Due to complex topography with narrow and shallow straits, the tides in the innermost parts of a fjord are both shifted in phase and altered in amplitude compared to the tides in the open water outside the fjord. Commonly, coastal tide information extracted from global or regional models is used on the boundary of the fjord model. Since tides vary over short distances in shallower waters close to the coast, the global and regional tidal forcings are usually too coarse to achieve sufficiently accurate tides in fjords. We present a straightforward method to remedy this problem by simply adjusting the tides to fit the observed tides at the entrance of the fjord. To evaluate the method, we present results from the Oslofjord, Norway. A model for the fjord is first run using raw tidal forcing on its open boundary. By comparing modelled and observed time series of water level at a tidal gauge station close to the open boundary of the model, a factor for the amplitude and a shift in phase are computed. The amplitude factor and the phase shift are then applied to produce adjusted tidal forcing at the open boundary. Next, we rerun the fjord model using the adjusted tidal forcing. The results from the two runs are then compared to independent observations inside the fjord in terms of amplitude and phases of the various tidal components, the total tidal water level, and the depth integrated tidal currents. The results show improvements in the modelled tides in both the outer, and more importantly, the inner parts of the fjord.     

Levee effects upon flood levels: an empirical assessment

This study used stream gauge records to assess the impact of levees on flood levels, providing an empirical test of theoretical and model predictions of the effects on local flood response. Focusing upon a study area in Illinois and Iowa for which levee records were available, we identified 203 gauges with ≥ 50 years hydrological record, including 15 gauges where a levee was constructed during the period of record. At these sites, step‐change analysis utilizing regression residuals tested levee‐related stage changes and levels of significance and quantified the magnitudes of stage changes. Despite large differences in stream sizes, levee alignments, and degree of floodplain constriction, the post‐levee rating‐curve adjustments showed consistent signatures. For all the study sites, stages for below bankfull (non‐flood) conditions were unaffected by levee construction. For above bankfull (flood) conditions, stages at sites downstream of their associated levees also were statistically indistinguishable before versus after levee construction. However, at all sites upstream of levees or within leveed reaches, stages increased for above bankfull conditions. These increases were abrupt, statistically significant, and generally large in magnitude – ranging up to 2.3 m (Wabash River at Mt. Carmel, IL). Stage increases began when discharge increased above bankfull flow and generally increased in magnitude with discharge until the associated levee(s) were overtopped. Detailed site assessments and supplementary data available from some sites helped document the dominant mechanisms by which levees can increase flood levels. Levee construction reduces the area of the floodplain open to storage of flood waters and reduces the width of the floodplain open to conveyance of flood flow. Floodplain conveyance often is underestimated or ignored, but Acoustic Doppler Current Profiler (ADCP) measurements analysed here confirm previous studies that up to 70% or more of the total discharge during large floods (~3% chance flood) can move over the floodplain. Upstream of levees and levee‐related floodplain constriction, backwater effects reduce flow velocities relative to pre‐levee conditions and, thus, increase stages for a given discharge. The empirical results here confirm a variety of theoretical predictions of levee effects but suggest that many one‐dimensional model‐based predictions of levee‐related stage changes may underestimate actual levee impacts. Copyright © 2011 John Wiley & Sons, Ltd.     

Generation and evolution of a topographically linked,mesoscale eddy under steady and variable wind-forcing

Numerical simulations with the Regional Ocean Modeling System (ROMS) are used to study the initial spin-up and the evolution of a mesoscale, topographically linked eddy under steady and variable wind conditions. The development of a pool of dense water on the southern Vancouver Island shelf allows cyclonic eddies formed by coastal upwelling off Cape Flattery to spread westward, ultimately contributing to the shelf-wide circulation known as the Juan de Fuca Eddy. This dense water arises through upwelling of water present in the underlying canyon system and tidal mixing over several shallow banks to the north. Tidal mixing is critical to the separation of the eddy from the coast. Although steady upwelling winds with a seasonal mean magnitude (combined with estuarine flow and tides) produce an eddy, only fluctuating winds with timescales and magnitudes typical of the region result in an eddy with a westward extent similar to seasonal observations. With each period of upwelling-favorable winds, newly upwelled water from the coast is entrained into the eddy which grows in size and moves westward. Wind events also significantly affect the baroclinic structure of the eddy. Specifically, during typical summer wind reversals, model surface drifters continue to move cyclonically within the eddy for several days after each downwelling wind event. Under upwelling-favorable wind conditions, model drifters exit the eddy to the southeast as the eddy and coastal upwelling fronts merge into a continuous southeastward shelf break jet.     

A two-dimensional analytical solution of groundwater responses to tidal loading in an estuary and ocean

Previous studies on tidal dynamics of coastal aquifers have focussed on the inland propagation of oceanic tides in the cross-shore direction, a configuration that is essentially one-dimensional. Aquifers at natural coasts can also be influenced by tidal waves in nearby estuaries, resulting in a more complex behaviour of head fluctuations in the aquifers. We present an analytical solution to the two-dimensional depth-averaged groundwater flow equation for a semi-infinite aquifer subject to oscillating head conditions at the boundaries. The solution describes the tidal dynamics of a coastal aquifer that is adjacent to a cross-shore estuary. Both the effects of oceanic and estuarine tides on the aquifer are included in the solution. The analytical prediction of the head fluctuations is verified by comparison with numerical solutions computed using a standard finite-difference method. An essential feature of the present analytical solution is the interaction between the cross- and along-shore tidal waves in the aquifer area near the estuary’s entry. As the distance from the estuary or coastline increases, the wave interaction is weakened and the aquifer response is reduced, respectively, to the one-dimensional solution for oceanic tides or the solution of Sun (Sun H. A two-dimensional analytical solution of groundwater response to tidal loading in an estuary, Water Resour Res 1997;33:1429–35) for two-dimensional non-interacting tidal waves.     

Perturbation of regional ocean tides due to coastal dikes

The tidal regime modeling system for ocean tides in the seas bordering the Korean Peninsula is designed to cover an area that is broad in scope and size, yet provide a high degree of resolution in coastal development areas, including the Saemangeum area in the eastern Yellow Sea and the Ariake Sea in Japan, where serious environmental problems have occurred after the completion of interior tidal dikes. With this simulation system, we have estimated the changes in tidal regime due to barriers at Saemangeum and Isahaya Bay in the Ariake Sea. Some results in terms of perturbations in tidal elevations due to the construction of coastal dikes are presented and discussed.     

Simulating the role of tides and sediment characteristics on tidal flat sorting and bedding dynamics

Understanding sediment sorting and bedding dynamics has high value to unravelling the mechanisms underlying geomorphological, geological, ecological and environmental imprints of tidal wetlands and hence to predicting their future changes. Using the Nanhui tidal flat on the Changjiang (Yangtze) Delta, China, as a reference site, this study establishes a schematized morphodynamic model coupling flow, sediment dynamics and bed level change to explore the processes that govern sediment sorting and bedding phenomena. Model results indicate an overall agreement with field data in terms of tidal current velocities, suspended sediment concentrations (SSCs), deposition thicknesses and sedimentary structures. Depending on the variation of tidal current strength, sand-dominated layers (SDLs) and mud-dominated layers (MDLs) tend to form during spring and neap tides, respectively. Thinner tidal couplets are developed during daily scale flood–ebb variations. A larger tidal level variation during a spring–neap tidal cycle, associated with a stronger tidal current variation, favours the formation of SDLs and tidal couplets. A larger boundary sediment supply generally promotes the formation of tidal bedding, though the bedding detail is partially dependent on the SSC composition of different sediment types. Sediment properties, including for example grain size and settling velocity, are also found to influence sediment sorting and bedding characteristics. In particular, finer and coarser sediment respond differently to spring and neap tides. During neap tides, relatively small flow velocities favour the deposition of finer sediment, with limited coarser sediment being transported to the upper tidal flat because of the larger settling velocity. During spring tides, larger flow velocities transport more coarser sediment to the upper tidal flat, accounting for distinct lamination formation. Model results are qualitatively consistent with field observations, but the role of waves, biological processes and alongshore currents needs to be included in further studies to establish a more complete understanding.     

Eemian landscape response to climatic shifts and evidence for northerly Neanderthal occupation at a palaeolake margin in northern Germany

The prevailing view suggests that the Eemian interglacial on the European Plain was characterized by largely negligible geomorphic activity beyond the coastal areas. However, systematic geomorphological studies are sparse. Here we present a detailed reconstruction of Eemian to Early Weichselian landscape evolution in the vicinity of a small fingerlake on the northern margin of the Salzwedel Palaeolake in Lower Saxony (Germany). We apply a combination of seismics, sediment coring, pollen analysis and luminescence dating on a complex sequence of colluvial, paludal and lacustrine sediments. Results suggest two pronounced phases of geomorphic activity, directly before the onset and at the end of the Eemian period, with an intermediate period of pronounced landscape stability. The dynamic phases were largely driven by incomplete vegetation cover, but likely accentuated by fluvial incision in the neighbouring Elbe Valley. Furthermore, we discovered Neanderthal occupation at the lakeshore during Eemian pollen zone (PZ) E IV, which is chronologically in line with other known Eemian sites of central Europe. Our highly-resolved spatio-temporal data substantially contribute to the understanding of climate-induced geomorphic processes throughout and directly after the last interglacial period. It helps unraveling the landscape dynamics between the coastal areas to the north and the loess belt to the south.     

Near-bed sediment transport in a heavily modified coastal plain estuary

Numerous estuaries of the world have been strongly modified by human activities.These interferences can make great adjustments of not only sediment transport processes,but also the collective behavior of the estuary.This paper provides a typical case of a heavily modified coastal plain estuary of Sheyang on the China coast,where a sluice barrage was built in 1956 to stop the intrusions of storm surges and saline water.Four sets of instrumented tripods were simultaneously deployed along a cross-shore transect to continuously observe near-bed flow currents and sediment transport.The in-situ surveys lasted over a spring and neap tide cycle when a strong wind event occurred in the neap tide.Comparisons of flows and sediment transport between tide-dominated and wind-dominated conditions demonstrated the important role of episodic wind events in flows and sediment transport.The wind-induced currents,bottom stresses,and sediment transport rates were significantly greater when wind was present than corresponding quantities induced by the tides.The long-shore sediment transport induced by winds exceeds the cross-shore component,especially near the river mouth bar.These results indicate the noticeable importance of wave-dominated coastal processes in shaping topographic features.A regime shift of estuarine evolution under highly intense human forcing occurs from fluvial to marine processes.This finding suggests that the management strategy of the estuarine system should focus on the restoration of estuarine processes,rather than the present focus on inhibition of marine dynamics.     

Modelling of groundwater–vegetation interactions in a tidal marsh

Wetting and drying due to tidal fluctuations affect soil conditions and hence plant growth in tidal marshes. Here, a coupled one-dimensional model was developed to simulate interacting groundwater flow and plant growth in these wetlands. The simulation results revealed three characteristic zones of soil conditions for plant growth along a cross-creek section subjected to the combined influences of spring-neap tides and evapotranspiration: (1) a near-creek zone affected by semi-diurnal tides over the whole spring-neap cycle, where the soil is well aerated although the plant growth could be slightly limited by the local water content dropping periodically below the wilting point on the ebb tide; (2) a less well-drained zone where drainage occurs only during neap tides (for which the daily inundation is absent) and plant growth is aeration-limited; and (3) an interior zone where evapotranspiration determines the soil–water saturation. Plant growth dynamics, which depend on these soil conditions, lead to spatial biomass distributions that are consistent with the characteristic zonation. The simulations shed light on the feedback mechanism for groundwater–vegetation interactions in the marsh system. It was demonstrated that the growth of pioneer plants can improve the soil aeration condition as a result of transpiration. The strength of this feedback varies spatially in accordance with the three characteristic zones of soil–water saturation. However, the development of another species in the marsh system is likely to be more complicated than suggested by the “positive feedback” mechanism proposed previously, due to the influence of inter-species competition. The feedback effects are generally more complex, involving both plant growth enhancement and inhibition depending on the combined influence of the intra- and inter-species competition, the ecosystem’s carrying capacity and plant transpiration. These findings demonstrate the interplay of ecological and hydrological processes in tidal marshes, and provide guidance for future research, including field investigations that aim to establish the principle relationship between marsh morphology and plant zonation.     

Quantifying sediment storage on the floodplains outside levees along the lower Yellow River during the years 1580–1849

The lower Yellow River channel was maintained by artificial levees between 1580 and 1849. During this period, 280 levee breaches occurred. To estimate sediment storage on the floodplains outside the levees, a regression model with a decadal time step was developed to calculate the outflow ratio for the years when levee breaching occurred. Uncertainty analysis was used to identify the likely outflow ratio. Key variables of the model include annual water discharge, a proxy for levee conditions, and potential bankfull discharge of the channel before flood season. Uncertainty analysis reveals an outflow ratio of 0.35–0.56. We estimate that during this period, 18.8–30.1% of the total ~312 Gt of sediment load was deposited on the floodplains outside the levees. Human-accelerated erosion in the Loess Plateau caused a 4-fold increase in sediment delivery to the lower Yellow River, which could not be accommodated by channel morphodynamic changes. As a result, 21.2–27.5% of the total sediment load was deposited within the levees, creating a super-elevated channel bed that facilitated an uncommonly high breach outflow ratio. Hence, the factor of a large super-elevation relative to the mean main channel depth should be considered when designing diversions to restore floodplains. © 2018 John Wiley & Sons, Ltd.     

Seasonal,tidal, and geomorphic controls on sediment export to Amazon River tidal floodplains

Mainstem–floodplain material exchange in the tidal freshwater reach of major rivers may lead to significant sequestration of riverine sediment, but this zone remains understudied compared to adjacent fluvial and marine environments. This knowledge gap prompts investigation of floodplain-incising tidal channels found along the banks of tidal rivers and their role in facilitating water and suspended-sediment fluxes between mainstem and floodplain. To evaluate this role, and how it evolves along the tidal river and with time, we measured water level, flow velocity, temperature, and suspended-sediment concentration (SSC) in four tidal channels along the tidal Amazon River, Brazil. Eleven deployments were made during low, rising, high, and falling seasonal Amazon discharge. Generally, channels export high-SSC water from the mainstem to the tidal floodplain on flood tides and transfer low-SSC water back to the mainstem on ebbs. Along the length of the tidal river, the interaction between tidal and seasonal water-level variations and channel–floodplain morphology is a primary control on tidal-channel sediment dynamics. Close to the river mouth, where tides are large, this interaction produces transient flow features and current-induced sediment resuspension, but the importance of these processes decreases with distance upstream. Although the magnitude of the exchange of water and sediment between mainstem and floodplain via tidal channels is a small percentage of the total mainstem discharge in this large tidal-river system, tidal channels are important conduits for material flux between these two environments. This flux is critical to resisting floodplain submergence during times of rising sea level. © 2019 John Wiley & Sons, Ltd.