危岩体在地震作用过程中的失稳模式及稳定性评价

地震作用过程中地震加速度通常呈先增大后减小的特征。利用拟静力法对危岩的稳定性进行分析时,考虑地震过程中地震加速度的变化,对山西太原天龙山危岩体加固工程中的同一危岩体分别以滑塌式和倾倒式破坏模式进行计算,发现地震作用过程中危岩体可能在两种破坏失稳模式之间相互转化。将此问题扩展至一般情况进行计算并讨论,得出如下结论:地震力对危岩体破坏作用的贡献大小不同,通常情况下,地震作用力对危岩的倾覆力矩贡献相对较大;进行稳定性评价时应考虑地震作用过程,以安全系数最先达到1.0的破坏模式作为危岩体的可能破坏模式进行计算;对危岩体进行抗震加固设计时应对加固设计进行多种工况下的校核,保证其在地震作用过程中不同危险状态的稳定性。     

Toppling failures from alpine cliffs on ben Lomond,Tasmania

Large cliff failures involving forward toppling over a basal hinge have occurred on more than half of the plateau edge of Ben Lomond, northeastern Tasmania. This mode of failure, which is readily identified from the columnar structure of the dolerite involved, has affected up to 10⁷ m³ of rock at a time and a total of more than 50 × 10⁶ m³ in all the cases which can still be identified. It represents perhaps the most important form of cliff retreat, amounting to a rate of 0.2 mm yr^?1 over the last 100,000 years. Topographic evidence and joint surveys suggest that two different mechanisms have produced the topples on Ben Lomond. One has involved failure in the sediments underlying the dolerite with consequent foundering and cambering of large sections of the plateau edge. This mechanism accounts for relatively few of the Ben Lomond topples, though it includes the largest individual cases. The second mechanism, dominant in most of the topples, involved slab failure in the cliffs. Both modes of failure have been facilitated by vertical weaknesses within the bedrock and both require an initially steep cliff profile. Because of the latter requirement, which is not met on the other mountains of northeastern Tasmania, large-scale topples are found only on Ben Lomond, and only there where glacial steepening of the cliff has been possible. Following the initial failure, topples of both types have migrated downslope by block sliding for distances up to 2 km.     

Rock fall dynamics and deposition: an integrated analysis of the 2009 Ahwiyah Point rock fall,Yosemite National Park,USA

We analyzed a combination of airborne and terrestrial LiDAR, high‐resolution photography, seismic, and acoustic data in order to gain insights into the initiation, dynamics, and talus deposition of a complex rock fall. A large (46 700 m³) rock fall originated from near Ahwiyah Point in eastern Yosemite Valley and fell a total of 730 m to the valley floor on 28 March 2009. Analyses of remote sensing, seismic, and acoustic data were integrated to reconstruct the rock fall, which consisted of (1) the triggering of a 25 400 m³ rock block in an area of intersecting and sometimes highly weathered joint planes, (2) the sliding and subsequent ballistic trajectory of the block from a steeply dipping ledge, (3) dislodging of additional rock from the cliff surface from beneath the rock fall source area, (4) a mid‐cliff ledge impact that detached a volume of rock nearly equivalent in volume to the initial block, (5) sliding of the deteriorating rock mass down the remainder of the cliff, and (6) final impact at the base of the cliff that remobilized the existing talus downward and outward and produced an airblast that knocked down hundreds of trees. The depositional geomorphology indicates that the porosity of the fresh talus is significantly lower than that expected for typical blocky talus slopes, likely because the rock debris from this event was pulverized into smaller, more poorly sorted fragments and densified via dynamic compaction when compared to less energetic, fragmental‐type rock falls. These results suggest that accumulation of individual rock‐fall boulders tends to steepen talus slopes, whereas large, energetic rock falls tend to flatten them. Detachment and impact signals were recorded by seismic and acoustic instruments and highlight the potential use of this type of instrumentation for generalized rock fall monitoring, while LiDAR and photography data were able to quantify the cliff geometry, rock fall volume, source and impact locations, and geomorphological changes to the cliff and talus. Published in 2012. This article is a US Government work and is in the public domain in the USA.     

Progressive failure of sheeted rock slopes: the 2009–2010 Rhombus Wall rock falls in Yosemite Valley,California, USA

Progressive rock‐fall failures in natural rock slopes are common in many environments, but often elude detailed quantitative documentation and analysis. Here we present high‐resolution photography, video, and laser scanning data that document spatial and temporal patterns of a 15‐month‐long sequence of at least 14 rock falls from the Rhombus Wall, a sheeted granitic cliff in Yosemite Valley, California. The rock‐fall sequence began on 26 August 2009 with a small failure at the tip of an overhanging rock slab. Several hours later, a series of five rock falls totaling 736 m³ progressed upward along a sheeting joint behind the overhanging slab. Over the next 3 weeks, audible cracking occurred on the Rhombus Wall, suggesting crack propagation, while visual monitoring revealed opening of a sheeting joint adjacent to the previous failure surface. On 14 September 2009 a 110 m³ slab detached along this sheeting joint. Additional rock falls between 30 August and 20 November 2010, totaling 187 m³, radiated outward from the initial failure area along cliff (sub)parallel sheeting joints. We suggest that these progressive failures might have been related to stress redistributions accompanying propagation of sheeting joints behind the cliff face. Mechanical analyses indicate that tensile stresses should occur perpendicular to the cliff face and open sheeting joints, and that sheeting joints should propagate parallel to a cliff face from areas of stress concentrations. The analyses also account for how sheeting joints can propagate to lengths many times greater than their depths behind cliff faces. We posit that as a region of failure spreads across a cliff face, stress concentrations along its margin will spread with it, promoting further crack propagation and rock falls. Published in 2012. This article is a US Government work and is in the public domain in the USA.     

Geometrical simulation studies of coastal cliff failures in liassic strata,South Wales,U.K.

Three numerical models of cliff failure have been developed, based on analyses of rockfalls along the 22 km Liassic coastline of the Glamorgan Heritage Coast, U.K. Detailed field investigation of the bucklandi (limestone dominated) and angulata (mudstone dominated) Lias series at four locations confirm the veracity of the models. Translation failure was correctly predicted at the mainly limestone buttressed cliff sites in the bucklandi and at locations where the angulata series formed a high proportion of the cliff mass. Toppling was predicted for vertical and overhanging cliffs with basal undercutting. The factor of safety reduces as the ratio of undercutting depth (d) to tension fracture distance (D) from the cliff face increases. Instability can be triggered by thrust forces generated by wave/tide impact, freeze/thaw and expansion/contraction associated with clay infill. Thrust forces can be modest, ranging from 1·7 to 2·7 MN m², but can exceed the cross-joint strength as weathering proceeds.     

Conceptual model of fracture-limited sea cliff erosion: Erosion of the seaward tilted flyschs of Socoa,Basque Country,France

Sea cliff morphology and erosion rates are modulated by several factors, including rock control that reflects both lithology and rock structure. Erosion is anticipated to preferentially exploit ‘fractures’, broadly meant as any discontinuity in an otherwise continuous medium, where the rock mass is weakest. Unpicking the direct control of such fractures on the spatial and temporal pattern of erosion remains, however, challenging. To analyse how such fractures control erosion, we monitored the evolution of a 400 m-long stretch of highly structured sedimentary cliffs in Socoa, Basque Country, France. The rock is known as the Socoa flysch formation. This formation combines decimetre-thick turbidites composed of repeat triplets of medium to strong calcareous sandstone, laminated siltstones and argillaceous marls. The sequence plunges at 45° into the sea with a shore-parallel strike. The cliffs are cross-cut by two normal and reverse fault families, with 10–100 m alongshore spacing, with primary and secondary strata-bound fractures perpendicular to the bedding, which combined delimit the cliff rock mass into discrete blocks that are exploited by the erosion process. Erosion, and sometimes plucking, of such beds and blocks on the cliff face was monitored using ground-based structure-from-motion (SfM) photogrammetry, over the course of 5.7 years between 2011 and 2017. To compare with longer time change, cliff-top retreat rate was assessed using SfM-orthorectified archive aerial photographs spanning 1954–2008. We show that the 13,250 m² cliff face released 4500 blocks exceeding 1.45 × 10⁻³ m³, removing a total volume of 170 m³. This equates to an average cliff erosion rate of 3.4 mm/year, which is slightly slower than the 54-year-long local cliff-top retreat (10.8 ± 1.8 mm/year). The vertical distribution of erosion reflects the height of sea water inundation, where the maximum erosion intensity occurs ca. 2 m above high spring-tide water level. Alongshore, the distribution of rockfall scars is concentrated along bed edges bounding cross-cutting faults; the extent of block detachment is controlled by secondary tectonic joints, which may extend through several beds locally sharing similar mechanical strength; and rockfall depth is always a multiple of bed thickness. Over the longer term, we explain block detachment and resultant cliff collapse as a cycle. Erosion nucleates on readily exploitable fractures but elsewhere, the sea only meets defect-free medium-strong to strong rock slabs offering few morphological features for exploitation. Structurally delimited blocks are quarried, and with sufficient time, carve semi-elliptic scars reaching progressively deeper strata to be eroded. Lateral propagation of erosion is directed along mechanical weaknesses in the bedding, and large episodic collapses affect the overhanging slabs via sliding on the weak marl beds. Collapse geometry is confined to one or several triplets of turbidite beds, but never reaches deeper into the cliff than the eroded depth at the foot. We contend that this fracture-limited model of sea-cliff erosion, inferred from the Socoa site dynamics and its peculiar sets of fractures, applies more broadly to other fractured cliff contexts, albeit with site-specific geometries. The initiation of erosion, the propagation of incremental block release and the ultimate full failure of the cliff, have each been shown to be fundamentally directly controlled by structure, which remains a vital control in understanding how cliffed coasts have changed in the past and will change in the future.     

Salt marsh cliff stability in the oosterschelde

Salt marsh cliff erosion in the Oosterschelde, due to basal scour and small-scale failure, was monitored during a two-year period using reference stakes. The composite marsh cliffs have a cantilever profile. Their stability is evaluated from beam failure analysis. A model is proposed, in which the cantilever weight is taken as the motive force; the major resistive force is the tensile strength. By substituting height, undermining width and soil mechanical properties of the cliff in the model, one can identify the cliffs that are likely to fail. Salt marsh cliffs, which combine a large tensile strength due to roots at the top of the profile with a large compressive stress at the cliff base due to the sandy texture of the subsoil, display the highest resistance to beam failure. The critical cliff dimensions, observed in the field, correspond with the values calculated from the proposed model of beam failure.     

地震与水压力耦合作用下岩质边坡倾覆解析方法

以往对平面破坏模式的岩质边坡稳定性评价,主要关注潜在滑坡体在自重、坡体内静水压力和地震荷载耦合作用下沿破坏面的抗滑稳定性,并未涉及各类外荷载作用线不通过潜在滑体重心而引起的绕坡趾倾覆稳定性。针对这一问题,提出地震与张裂缝水压耦合作用下的岩质边坡倾覆稳定性解析方法,基于力矩平衡原理推导出岩质边坡抗倾覆稳定性系数的一般表达式;通过深入的变动参数比较研究,探讨张裂缝水压和地震荷载对抗倾覆安全系数的影响,认为水压是控制岩质边坡倾覆破坏的决定性因素,而地震荷载处于次要因素,其在一定程度上增加或减小抗倾覆稳定性。在此基础上建立不同参数组合下的岩质边坡抗倾覆稳定图,为工程技术人员快速评估饱水岩质边坡地震倾覆稳定性提供直接依据。     

Critical notch depths for failure of coastal limestone cliffs: case study at Kuro‐shima Island,Okinawa, Japan

Development of a notch at the base of a cliff reduces cliff stability and often induces a collapse. Pleistocene limestone coastal cliffs of elevation 5?m in Kuro‐shima, Ryukyu Islands, have a prominent notch with a depth of 3–4?m at their bases. Around these coastal cliffs, collapses different from previous studies of cliff collapses in the Ryukyu Islands were found; collapses in Kuro‐shima have a horizontal failure surface. The horizontal failure surface, situated at the height of the failure surface corresponding to the retreat point of the notch, is bounded by vertical joints cutting the whole cliff and the reef flat in front of the cliff. Two types of horizontal failure surface were found, triangular and quadrangular; the distinction appears to depend on the angle between the vertical joints and the front face of the cliff. Prior to collapse, these cliffs appear to have been separated from the adjacent cliffs by the development of vertical joints. Consequently, a cliff that will collapse can be identified in advance; cliff instability is strongly dependent on the development of a notch. To study the effect of notch development on cliff collapse, the notch depth at which collapse occurs was calculated using stability analysis. Instability of a cliff increases with notch depth; collapse occurs at the horizontal failure surface when the ratio of the notch depth to the seaward length of the cliff is approximately 0·5–0·7 for a triangular failure surface, and 0·7–0·9 for a quadrangular failure surface. Copyright © 2010 John Wiley & Sons, Ltd.     

Catastrophic rock avalanche 3600 years BP from El Capitan,Yosemite Valley,California

Large rock slope failures from near‐vertical cliffs are an important geomorphic process driving the evolution of mountainous landscapes, particularly glacially steepened cliffs. The morphology and age of a 2·19 × 10⁶ m³ rock avalanche deposit beneath El Capitan in Yosemite Valley indicates a massive prehistoric failure of a large expanse of the southeast face. Geologic mapping of the deposit and the cliff face constrains the rock avalanche source to an area near the summit of ～8·5 × 10⁴ m². The rock mass free fell ～650 m, reaching a maximum velocity of 100 m s^?1, impacted the talus slope and spread across the valley floor, extending 670 m from the base of the cliff. Cosmogenic beryllium‐10 exposure ages from boulders in the deposit yield a mean age of 3·6 ± 0·2 ka. The ～13 kyr time lag between deglaciation and failure suggests that the rock avalanche did not occur as a direct result of glacial debuttressing. The ～3·6 ka age for the rock avalanche does coincide with estimated late Holocene rupture of the Owens Valley fault and/or White Mountain fault between 3·3 and 3·8 ka. The coincidence of ages, combined with the fact that the most recent (AD 1872) Owens Valley fault rupture triggered numerous large rock falls in Yosemite Valley, suggest that a large magnitude earthquake (≥M7.0) centered in the south‐eastern Sierra Nevada may have triggered the rock avalanche. If correct, the extreme hazard posed by rock avalanches in Yosemite Valley remains present and depends on local earthquake recurrence intervals. Published in 2010 by John Wiley & Sons, Ltd.     

基于数值流形法的反倾层状岩质边坡倾倒破坏分析

边坡破坏是累积性过程,从变形到破坏的过程中会产生永久位移,如果永久位移过大,极有可能产生滑坡.因此根据不同工况下采集到的位移数据,分析地震作用下反倾层状岩质边坡在不同内摩擦角下的破坏特征.利用二维数值流形法(NMM),以青藏高原金沙江流域西藏昌都地区芒康县索多西乡贡扎倾倒滑坡为研究对象,依据实地考察数据及室内力学试验得...     

Influence of rock mass strength on the erosion rate of alpine cliffs

Collapse of cliff faces by rockfall is a primary mode of bedrock erosion in alpine environments and exerts a first‐order control on the morphologic development of these landscapes. In this work we investigate the influence of rock mass strength on the retreat rate of alpine cliffs. To quantify rockwall competence we employed the Slope Mass Rating (SMR) geomechanical strength index, a metric that combines numerous factors contributing to the strength of a rock mass. The magnitude of cliff retreat was calculated by estimating the volume of talus at the toe of each rockwall and projecting that material back on to the cliff face, while accounting for the loss of production area as talus buries the base of the wall. Selecting sites within basins swept clean by advancing Last Glacial Maximum (LGM) glaciers allowed us to estimate the time period over which talus accumulation occurred (i.e. the production time). Dividing the magnitude of normal cliff retreat by the production time, we calculated recession rates for each site. Our study area included a portion of the Sierra Nevada between Yosemite National Park and Lake Tahoe. Rockwall recession rates determined for 40 alpine cliffs in this region range from 0·02 to 1·22 mm/year, with an average value of 0·28 mm/year. We found good correlation between rockwall recession rate and SMR which is best characterized by an exponential decrease in erosion rate with increasing rock mass strength. Analysis of the individual components of the SMR reveals that joint orientation (with respect to the cliff face) is the most important parameter affecting the rockwall erosion rate. The complete SMR score, however, best synthesizes the lithologic variables that contribute to the strength and erodibility of these rock slopes. Our data reveal no strong independent correlations between rockwall retreat rate and topographic attributes such as elevation, aspect, or slope angle. Copyright © 2009 John Wiley & Sons, Ltd.     

Effects of seismic devices on transverse responses of piers in the Sutong Bridge

The Sutong Bridge in China opened to traffic in 2008, and is an arterial connection between the cities of Nantong and Suzhou. It is a cable-stayed bridge with a main span of 1,088 m. Due to a tight construction schedule and lack of suitable seismic devices at the time, fixed supports were installed between the piers and the girder in the transverse direction. As a result, significant transverse seismic forces could occur in the piers and foundations, especially during a return period of a 2500-year earthquake. Therefore, the piers, foundations and fixed bearings had to be designed extraordinarily strong. However, when larger earthquakes occur, the bearings, piers and foundations are still vulnerable. The recent rapid developments in seismic technology and the performance-based design approach offer a better opportunity to optimize the transverse seismic design for the Sutong Bridge piers. The optimized design can be applied to the Sutong Bridge(as a retrofit), as well as other bridges. Seismic design alternatives utilizing viscous fluid dampers(VFD), or friction pendulum sliding bearings(FPSB), or transverse yielding metallic dampers(TYMD) are thoroughly studied in this work, and the results are compared with those from the current condition with fixed transverse supports and a hypothetical condition in which only sliding bearings are provided on top of the piers(the girder can move "freely" in the transverse direction during the earthquake, except for frictional forces of the sliding bearings). Parametric analyses were performed to optimize the design of these proposed seismic devices. From the comparison of the peak bridge responses in these configurations, it was found that both VFD and TYMD are very effective in the reduction of transverse seismic forces in piers, while at the same time keeping the relative transverse displacements between piers and the box girder within acceptable limits. However, compared to VFD, TYMD do not interact with the longitudinal displacements of the girder, and have simpler details and lower initial and maintenance costs. Although the use of FPSB can also reduce seismic forces, it generally causes the transverse relative displacements to be higher than acceptable limits.     

Statistical and empirical analyses of the triggers of coastal chalk cliff failure

The triggering factors of rock falls remain unknown due to a lack of exhaustive, regular and accurate surveys. Based on an inventory of 331 rock falls collected weekly between 2002 and 2009 from Veules‐les‐Roses to Le Treport (Upper Normandy), the relationships between coastal chalk cliff rock falls (dates and geomorphological features) and external factors commonly agreed as triggering (rainfall, temperature variations, tide and wind) are studied. The combination of multivariate statistical and empirical analyses indicates that (1) ‘cold and dry weather’ and ‘high rainfall and high wind’ are the conditions most likely to trigger rock falls, (2) the main triggering factors of rock falls are effective rainfall (for rock falls mostly between 200 and 1400 m³ or larger than 10 000 m³ and coming from the whole cliff face), freeze/thaw cycles (especially for rock falls smaller than 200 m³ and coming from the foot and top of the cliff face) and marine roughness (rock falls mainly smaller than 200 m³ and coming from the cliff foot). However, the contribution of each factor to triggering is difficult to determine because of combinations of factors (85% of 331 cases), relays of processes and hysteresis phenomena. In view of these first results, it is still presumptuous to predict the location and time of triggering of rock falls. However, the statistical and naturalistic approaches adopted and the observations made in this study are from an original database, and constitute a real starting point for the prediction and prevention of the hazard of coastal chalk cliff rock falls in Upper Normandy. Copyright © 2015 John Wiley & Sons, Ltd.     

Field observations of infragravity waves and their behaviour on rock shore platforms

Infragravity wave (IGW) transformation was quantified from field measurements on two shore platforms on New Zealand's east coast, making this the first study to describe the presence, characteristics and behaviour of IGWs on rock platform coasts. Data was collected using a cross‐shore array of pressure transducers during a 22 hour experiment on Oraka shore platform and a 36 hour experiment at Rothesay Bay shore platform. A low pass Fourier filter was used to remove gravity wave frequency oscillations, allowing separate analysis of IGWs and the full wave spectrum. Offshore IGW heights were measured to be 7 cm (Oraka) and 9 cm (Rothesay Bay), which were 21% (Oraka) and 7.5% (Rothesay Bay) the height of incident wave height. At the cliff toe, significant IGW height averaged 15 cm at Oraka and 13 cm at Rothesay Bay. This increase in IGW height over the platform during both experiments is attributed to shoaling of 40 to 55% over the last 50–60 m before the cliff toe, respectively. Shoaling across the platform was quantified as the change in IGW height from the platform edge to cliff toe, resulting in a maximum increase of 1·88 and 2·63 on Rothesay Bay and Oraka platforms. IGW height at the cliff toe showed a strong correlation with incident wave height. The proportional increase in IGW height shows a strong correlation to water level on each platform. The rate of shoaling of long period waves on the shallow, horizontal platforms increased at higher water levels resulting in a super elevation in water level at the cliff toe during high tide. Greater IGW shoaling was also observed on the wider (Oraka) shore platform. Results from this study show the first measurements of IGWs on shore platforms and identify long wave motion a significant process in a morphodynamic understanding of rock coast. Copyright © 2011 John Wiley & Sons, Ltd.     

地壳内岩石的化学组成与地震成因之间关系的探讨

本文从岩石的物理化学性质方面讨论了地壳内含量较少的基性、超基性岩对地震孕育的作用,通过理论上的探讨并与实际情况对比,分析了各类岩石的粘度特性,建立了一个确定构造运动粘滑或蠕滑的地面参考指标。     

Computation of sliding displacements of bridge abutments by pseudo-dynamic method

The paper focuses on seismic sliding displacement calculations of gravity wall bridge abutments when subjected to passive condition during earthquakes. Pseudo-dynamic approach has been used for the calculation of the passive seismic earth pressure. A novel element of the present investigation is the computation of seismic passive earth pressure coefficients by considering the composite curved rupture surface behind the abutment wall in the framework of limit equilibrium method. Sliding failure along the wall base is considered in the new pseudo-dynamic method. The critical seismic acceleration coefficient for sliding and sliding component of the displacement, resulting from horizontal and vertical sinusoidal ground accelerations, are computed by using Newmark's sliding block method. The effect of sliding on the response of earth structures is evaluated and comparisons are made between sliding displacements calculated using planar and composite failure mechanisms. Results of the comparative study showed that the assumption of planar failure mechanism for rough soil–wall interfaces significantly overestimates the critical seismic accelerations for sliding and underestimates the sliding displacements.     

太山龙泉寺舍利塔边坡地震稳定性研究

为了研究太原市太山龙泉寺拟建舍利塔边坡稳定性,对所在场地及外围地形地貌、地层、地质构造、水文条件进行了调查。结合7个探井,确定了塔址所在场地的土质边坡体可能失稳的模式,进行了边坡稳定性分析、计算。结果表明,场地在自然状态下边坡稳定系数为1.37,在烈度为Ⅷ、Ⅸ度地震影响下边坡稳定系数分别为1.24、1.15。根据《建筑边坡工程技术规范》（GB50330-2013）,塔址所在边坡是稳定的,不必对边坡进行处理;其次结合3个探槽揭露,发现场地北侧基岩边坡曾发生过滑动,据其滑动面倾角、滑动量及错断地层特征,认为是一种特殊边坡变形破坏-岩体错落,为崩塌与滑坡之间的中间类型,从现存的地形地貌特征分析,现阶段错落体已趋于基本稳定状态,稳定性较好;最后给出了预防边坡滑动的建议和措施,研究结果可为其他类似边坡场地地震稳定性研究提供参考借鉴。     

Modelling failure mechanisms to explain rock slope change along the Isle of Purbeck coast,UK

Results are presented of distinct element computer modelling used to examine rates and mechanisms of change in rock slopes and cliffs, where material intact properties determine process and form but the most significant controls are the joint pattern and cross-joint properties. The modelling approach does not appear to have been used before in a geomorphological context and provides an alternative approach for examining cliff development. Field and laboratory data have been collected for the Portland Limestone outcrop of the Isle of Purbeck, central southern England. The Portland Limestome is a hard, shelly, crystalline sediment of the Upper Jurassic. It has a regular discontinuity pattern throughout the outcrop in Purbeck. While joint orientation remains relatively constant, bedding changes from horizontal to vertical, a consequence of the Purbeck Monocline. There are resulting implications for spatial variations in rock slope evolution. The modelling exercise enhances previous knowledge on rock failure mechanisms and slope development along the Purbeck coast and demonstrates its potential in research where landforms are developed in lithified, jointed rock masses. © 1998 John Wiley & Sons, Ltd.     

Deformation structures associated with the Tazo landslide (La Gomera, Canary Islands)

Deformation structures below the basal plane of gravitational slides can provide useful information about the state of stress undergone by rocks prior to the sliding process and about the triggering forces acting at each particular sliding event. In the present work we conducted a structural analysis of the rocks below the surface of the gravitational slide of Tazo (La Gomera, Canary Islands) and determined the epigenetic processes involved in the filling of the amphitheatre. We also inferred the possible triggering phenomena related to the Tazo landslide. The rocks located below the surface of the gravitational slide of Tazo -i.e., the basaltic lava flows, sills and dikes of the Lower Old Edifice and the submarine volcanic rocks, gabbros, pyroxenites and dikes of the Basal Complex of La Gomera- are strongly deformed close to this sliding surface. The lava flows and dikes of the Lower Old Edifice are folded, with fault breccias and gouges, and locally foliated, defining the sliding surface. The dikes of the Basal Complex are also folded, and the gabbros and pyroxenites are affected by a large number of small faults. In the Basal Complex, the sliding surface is defined by a foliated granular gouge. In the damage zone, the Basal Complex rocks show an incipient fracture cleavage. The sliding amphitheatre has been filled by the debris avalanche or cohesive debris flow generated within the slide, as well as by later debris flows, hyperconcentrated flows, sheet flows, and by interspersed lava flows from the Upper Old Edifice. We suggest here that the collapse of the north-western flank of the Lower Old Edifice at Tazo could in part have been triggered by continuous magma injection, associated with the emplacement of dikes in a rift zone with an ENE-WSW direction, enhanced by the mechanical weakness of the Basal Complex unit, which was affected by hydrothermal metamorphism under greenschist facies conditions and by the displacement along the Montaña de Alcalá and Guillama normal faults, which are deeply entrenched in the altered rocks of the Basal Complex.