Study of P-wave velocities and attenuation coefficients of Gondwana rocks from Chanda-Wardha valley coalfield, Maharashtra, India

This paper describes the findings of the study pertaining to the laboratory measurements of longitudinal wave velocities and attenuation coefficients of various Gondwana rocks of Chikhalgaon, Saoner and Agarjhari areas of Chanda-Wardha valley coalfield. It is found that Barakar sandstones, in general, have higher longitudinal wave velocities than Barakar and Talchir shales and Kamthi sandstones. Of the Barakar sandstones, the fine grained feldspathised variety has the maximum velocity. Attenuation coefficients of coarse-grained rocks are higher than those of fine grained ones. Black carbonaceous shales of Barakar are characterised by moderately high longitudinal wave velocities and attenuation coefficients. Coals are characterized by low longitudinal wave velocities and high attenuation coefficients. Longitudinal wave velocities of the rocks along the bedding plane are always higher than those perpendicular to the bedding plane.     

Velocity anisotropy and attenuation of shale in under- and overpressured conditions

The seismic velocity and attenuation of fully saturated shales were measured for the first time under overpressured conditions, using the ultrasonic reflection technique. Shale cores from naturally overpressured horizons in the North Sea were tested in the laboratory, at confining and pore pressures relevant to in situ conditions.
A single-frequency tone-burst pulse wave was used to determine the seismic wave velocities and quality factors of the shale samples, with errors less than 0.3% and 0.1 dB/cm, respectively, at a frequency of 0.75 MHz. Sample length changes with varying confining and pore pressure were measured and the pore pressure equilibration time was monitored for each sample.
The anisotropy of the seismic attributes ( V _p, V _s, Q _p and Q _s) was determined over a range of differential pressures from 5 to 60 MPa, with respect to the predominant foliation. The ultrasonic velocity data followed a transversely isotropic pattern depending on the direction of wave propagation with respect to the laminations. The Poisson's ratio was found to rise by 5% as the shale material progressed from a normally pressured to an overpressured state. The quality factor ( Q ) characteristics were interpreted in terms of pore geometry and connectivity as well as the directional permeability of the transversely isotropic shale material. The results were converted to bulk and shear loss modulus defects, and a positive bulk loss was observed for waves propagating perpendicular to the lamination plane even above differential pressures of 20 MPa. This indicates different levels of Biot-flow and squirt-flow attenuation mechanisms acting within the shale structure, depending on the wave propagation and vibration directions.     

Texture and anisotropy analysis of Qusaiba shales

Scanning and transmission electron microscopy, synchrotron X‐ray diffraction, microtomography and ultrasonic velocity measurements were used to characterize microstructures and anisotropy of three deeply buried Qusaiba shales from the Rub’al‐Khali basin, Saudi Arabia. Kaolinite, illite‐smectite, illite‐mica and chlorite show strong preferred orientation with (001) pole figure maxima perpendicular to the bedding plane ranging from 2.4–6.8 multiples of a random distribution (m.r.d.). Quartz, feldspars and pyrite crystals have a random orientation distribution. Elastic properties of the polyphase aggregate are calculated by averaging the single crystal elastic properties over the orientation distribution, assuming a nonporous material. The average calculated bulk P‐wave velocities are 6.2 km/s (maximum) and 5.5 km/s (minimum), resulting in a P‐wave anisotropy of 12%. The calculated velocities are compared with those determined from ultrasonic velocity measurements on a similar sample. In the ultrasonic experiment, which measures the effects of the shale matrix as well as the effects of porosity, velocities are smaller (P‐wave maximum 5.3 km/s and minimum 4.1 km/s). The difference between calculated and measured velocities is attributed to the effects of anisotropic pore structure and to microfractures present in the sample, which have not been taken into account in the matrix averaging.     

Practical and robust experimental determination of c13 and Thomsen parameter δ

We analysed the complications in laboratory velocity anisotropy measurement on shales. There exist significant uncertainties in the laboratory determination of c₁₃ and Thomsen parameter δ. These uncertainties are primarily related to the velocity measurement in the oblique direction. For reliable estimation of c₁₃ and δ, it is important that genuine phase velocity or group velocity be measured with minimum uncertainty. The uncertainties can be greatly reduced if redundant oblique velocities are measured. For industrial applications, it is impractical to make multiple oblique velocity measurements on multiple core plugs. We demonstrated that it is applicable to make multiple genuine oblique group velocity measurements on a single horizontal core plug. The measurement results show that shales can be classified as a typical transversely isotropic medium. There is a coupling relation between c₄₄ and c₁₃ in determining the directional dependence of the seismic velocities. The quasi‐P‐wave or quasi‐S‐wave velocities can be approximated by three elastic parameters.     

Shear wave crustal velocity model of the Western Bohemian Massif from Love wave phase velocity dispersion

We propose a new quantitative determination of shear wave velocities for distinct geological units in the Bohemian Massif, Czech Republic (Central Europe). The phase velocities of fundamental Love wave modes are measured along two long profiles (~200 km) crossing three major geological units and one rift-like structure of the studied region. We have developed a modified version of the classical multiple filtering technique for the frequency-time analysis and we apply it to two-station phase velocity estimation. Tests of both the analysis and inversion are provided. Seismograms of three Aegean Sea earthquakes are analyzed. One of the two profiles is further divided into four shorter sub-profiles. The long profiles yield smooth dispersion curves; while the curves of the sub-profiles have complicated shapes. Dispersion curve undulations are interpreted as period-dependent apparent velocity anomalies caused both by different backazimuths of surface wave propagation and by surface wave mode coupling. An appropriate backazimuth of propagation is found for each period, and the dispersion curves are corrected for this true propagation direction. Both the curves for the long and short profiles are inverted for a 1D shear wave velocity model of the crust. Subsurface shear wave velocities are found to be around 2.9 km/s for all four studied sub-profiles. Two of the profiles crossing the older Moldanubian and Teplá-Barrandian units are characterized by higher velocities of 3.8 km/s in the upper crust while for the Saxothuringian unit we find the velocity slightly lower, around 3.6 km/s at the same depths. We obtain an indication of a shear wave low velocity zone above Moho in the Moldanubian and Teplá-Barrandian units. The area of the Eger Rift (Teplá-Barrandian–Saxothuringian unit contact) is significantly different from all other three units. Low upper crust velocities suggest sedimentary and volcanic filling of the rift as well as fluid activity causing the earthquake swarms. Higher velocities in the lower crust together with weak or even missing Moho implies the upper mantle updoming.     

How does water near clay mineral surfaces influence the rock physics of shales?

Clays and clay‐bearing rocks like shale are extremely water sensitive. This is partly due to the interaction between water and mineral surfaces, strengthened by the presence of nanometer‐size pores and related large specific surface areas. Molecular‐scale numerical simulations, using a discrete‐element model, show that shear rigidity can be associated with structurally ordered (bound or adsorbed) water near charged surfaces. Building on these and other molecular dynamics simulations plus nanoscale experiments from the literature, the water monolayer adjacent to hydrophilic solid surfaces appears to be characterised by shear stiffness and/or enhanced viscosity. In both cases, elastic wave propagation will be affected by the bound or adsorbed water. Using a simple rock physics model, bound water properties were adjusted to match laboratory measured P‐ and S‐wave velocities on pure water‐saturated kaolinite and smectite. To fit the measured stress sensitivity, particularly for kaolinite, the contribution from solid‐grain contact stiffness needs to be added. The model predicts, particularly for S‐waves, that viscoelastic bound water could be a source of dispersion in clay and clay‐rich rocks. The bound‐water‐based rock physics model is found to represent a lower bound to laboratory‐measured velocities obtained with shales of different mineralogy and porosity levels.     

裸眼井中弹性波传播的非对称模式的数值研究

本文从数值上研究了裸眼井中弹性波传播的非对称模式,给出了合成微地震图和导波（弯曲波）的频散曲线,发现在“硬”地层和“软”地层的井中,导波都是高度频散的,其最大相速度等于地层的横波速度,其截止频率低于对称模式的伪瑞利波的截止频率;在低频（2-3kHz）和长源距（3-4m）的条件下,由非对称的声源（如声偶极子）所产生的微地震图中,初至信号是以横波速度传播的,而以纵波速度传播的信号被抑制。本文的结果对研制横波速度测井仪是有意义的。     

Distribution of gas hydrate in fractured reservoirs: Insights from anisotropic seismic measurements

Seismic properties of hydrate-bearing reservoirs that are affected significantly by the hydrate distribution are key for quantitative assessment of the reservoir. The knowledge of hydrate distribution in fractured reservoirs remains poorly understood. To obtain such knowledge, we measured and analyzed five anisotropic velocities needed to fully characterize the seismic anisotropy in an artificial sandstone with aligned fractures during hydrate formation associated with varying distribution. We showed that while the formation of hydrate improved the velocities, the improvement was more significant for hydrate saturation above 10%. We also showed that the increasing trends varied among the anisotropic velocities when hydrate saturation was above 10%. Specifically, the compressional wave velocity travelling vertical to the bedding plane and the shear wave velocity with polarization perpendicular to the bedding plane increased more rapidly than the other compressional and shear wave velocities, respectively. Interpretation of the anisotropic seismic results suggested that the hydrate tends to bind to the grains in the fractures at low hydrate saturation, and becomes to bridge the fracture surfaces when the hydrate saturation exceeds 10%. The results have provided new insights into the hydrate distribution and its resulting anisotropic seismic properties in fractured reservoirs. This will pave the way for the successful assessment of hydrate in fractured reservoirs.     

Physical modeling observations of wave velocity and apparent attenuation in isotropic and anisotropic two-phase media

We study wave propagation through isotropic and anisotropic scatterer distributions in order to observe azimuthal variations in velocity and apparent attenuation. Using thin aluminum plates as physical models, we obtained seismograms for compressional and shear wave propagation through heterogeneous media. Three random distributions of scatterers are studied: circular scatterers in isotropic distributions (modeling circular scatterers), elongated scatterers in isotropic distributions (modeling randomly oriented elliptical scatterers), and elongated scatterers in anisotropic distributions (modeling aligned elliptical scatterers). All scatterers had approximately the same cross-sectional area and were filled with epoxy in order to reduce the impedance contrast. In addition to seismograms recorded for no scatterers, seismograms were recorded for several scatterer volume fractions. Azimuths were measured relative to the long axis of the aligned elongated scatterers. Velocities were calculated using travel times and phase shifts at low frequencies. The velocities measured from the data were compared to simple low-frequency average-velocity theories based on thin lamellae or on distributions of penny-shaped cracks. The apparent attenuation for different scatterer distributions was computed using spectral ratios.Comparisons of the results for circular and randomly oriented elongated scatterers were made to determine the effects of scatterer shape. As expected, the circular and randomly oriented elongated scatterers showed no systematic azimuthal variation in velocity. The velocity anomalies were systematically larger for the randomly oriented elongated scatterers than for the circular scatterers. Both methods of theoretical estimation for the isotropic velocities produced velocities significantly larger than those measured. The spectral ratios showed more apparent attenuation for the randomly oriented elongated scatterers than for the circular scatterers.Comparisons of the results for the randomly oriented and aligned elongated scatterers were made to determine the effects of anisotropy in the scatterer distribution. Compressional waves for the aligned elongated scatterers with wave propagation parallel to the scatterers had larger velocities than for the aligned elongated scatterers with wave propagation perpendicular to the scatterers for all velocity calculations. Shear wave velocities were complicated by an anomalous phase change in the shear wave seismograms for azimuths less than 40° and were not as conclusive. The general trend of the theoretical velocities is similar to the velocities calculated from the data. There are, however, what appear to be significant differences. The spectral ratios showed more apparent attenuation for the randomly oriented elongated scatterers than for the aligned elongated scatterers with wave propagation parallel to the scatterers, and less attenuation than for the aligned elongated scatterers with wave propagation perpendicular to the scatterers.     

Pore fluid viscosity effects on P‐ and S‐wave anisotropy in synthetic silica‐cemented sandstone with aligned fractures

Ultrasonic (500 kHz) P‐ and S‐wave velocity and attenuation anisotropy were measured in the laboratory on synthetic, octagonal‐shaped, silica‐cemented sandstone samples with aligned penny‐shaped voids as a function of pore fluid viscosity. One control (blank) sample was manufactured without fractures, another sample with a known fracture density (measured from X‐ray CT images). Velocity and attenuation were measured in four directions relative to the bedding fabric (introduced during packing of successive layers of sand grains during sample construction) and the coincident penny‐shaped voids (fractures). Both samples were measured when saturated with air, water (viscosity 1 cP) and glycerin (100 cP) to reveal poro‐visco‐elastic effects on velocity and attenuation, and their anisotropy. The blank sample was used to estimate the background anisotropy of the host rock in the fractured sample; the bedding fabric was found to show transverse isotropy with shear wave splitting (SWS) of 1.45 ± 1.18% (i.e. for S‐wave propagation along the bedding planes). In the fractured rock, maximum velocity and minimum attenuation of P‐waves was seen at 90° to the fracture normal. After correction for the background anisotropy, the fractured sample velocity anisotropy was expressed in terms of Thomsen's weak anisotropy parameters ε, γ & δ. A theory of frequency‐dependent seismic anisotropy in porous, fractured, media was able to predict the observed effect of viscosity and bulk modulus on ε and δ in water‐ and glycerin‐saturated samples, and the higher ε and δ values in air‐saturated samples. Theoretical predictions of fluid independent γ are also in agreement with the laboratory observations. We also observed the predicted polarisation cross‐over in shear‐wave splitting for wave propagation at 45° to the fracture normal as fluid viscosity and bulk modulus increases.     

Finite difference modeling of seismic wave propagation in monoclinic media

Reported in the present paper are the results of the study of propagation of SH waves in the plane of mirror symmetry of a monoclinic multilayered medium with displacement normal to the plane. Dispersion equation has been obtained analytically ussing Haskell’s matrix method, while the finite-difference method has been employed to model the SH-wave propagation to study its phase and group velocities. The stability analysis has been carried out to minimize the exponential growth of the error of finite difference approximation in order to make the finite difference method stable and convergent. Further, variations of phase velocity with respect to both wave number and dispersion parameter for different stability ratios in monoclinic media have been examined and shown graphically. The effect of change of stability ratio on the group velocity of the wave propagation has been also investigated. Likewise, the effects of change of dispersion parameter on phase velocity and the variation of frequency with increase of wave number have been graphically represented and discussed.     

低孔隙度泥页岩应力依赖的各向异性裂纹演化特性研究

本文在实验室对所获取的东营地区层理发育的低孔隙度页岩和泥岩的各向异性裂纹演化特性进行了研究,获得了各向同性条件下泥页岩的力学与超声波响应特性,分析了应力幅度对于页岩声波速度和各向异性的影响.主要结论包括:(1)泥页岩在循环载荷下存在滞后效应,表明其经历了去压实或油气产生导致的超压;(2)泥岩和页岩具有不同程度的各向异性,随着各向同性压力的增高微裂隙逐渐闭合,样品的各向异性程度减弱;(3)分析了岩石韧度和裂纹损伤参数随压力的变化特征,相比泥岩,页岩各向异性程度更高,随压力变化更明显,其裂纹导致的附加各向异性更强;(4)分析了各向异性岩石的动态弹性模量特征,由于软裂隙空间的闭合,动态弹性模量在低压条件下都随着围压的增加有硬化趋势.     

MEASURED ANISOTROPY IN PIERRE SHALE*

The five elastic coefficients which characterize a transversely isotropic medium have been measured for the Pierre Shale. The first-arrival times deduced from two closely spaced vertical seismic profiles provide values of magnitude and direction of the phase velocity at a given depth for different locations of the sources. From these velocities, we can estimate the five elastic coefficients by assuming that the P- and SV-wave velocities have only a small dependence on the angle of propagation. On the other hand, it is shown that the accuracy in the difference between the directions of propagation and particle motion is not sufficient to determine the anisotropy. This work was industrially sponsored through the Integrated Geophysics Project.     

Crustal and upper mantle structures of the brazilian coast

The Rayleigh wave phase and group velocities in the period range of 24–39 sec, obtained from two earthquakes which occurred in northeastern brazil and which were recorded by the Brazilian seismological station RDJ (Rio de Janeiro), have been used to study crustal and upper mantle structures of the Brazilian coastal region. Three crustal and upper mantle models have been tried out to explain crustal and upper mantle structures of the region. The upper crust has not been resolved, due basically to the narrow period range of the phase and group velocities data. The phase velocity inversions have exhibited good resolutions for both lower crust and upper mantle, with shear wave velocities characteristic of these regions. The group velocity data inversions for these models have showed good results only for the lower crust. The shear wave velocities of the lower crust (3.86 and 3.89 km/sec), obtained with phase velocity inversions, are similar to that (=3.89 km/sec) found byHwang (1985) to the eastern South American region, while group velocity inversions have presented shear velocity (=3.75 km/sec) similar to that (=3.78 km/sec) found byLazcano (1972) to the Brazilian shield. It was not possible to define sharply the crust-mantle transition, but an analysis of the phase and group velocity inversions results has indicated that the total thickness of the crust should be between 30 and 39 km. The crustal and upper mantle model, obtained with phase velocity inversion, can be used as a preliminary model for the Brazilian coast.     

Anisotropic reverse-time migration for tilted TI media

Seismic anisotropy in dipping shales results in imaging and positioning problems for underlying structures. We develop an anisotropic reverse‐time depth migration approach for P‐wave and SV‐wave seismic data in transversely isotropic (TI) media with a tilted axis of symmetry normal to bedding. Based on an accurate phase velocity formula and dispersion relationships for weak anisotropy, we derive the wave equation for P‐wave and SV‐wave propagation in tilted transversely isotropic (TTI) media. The accuracy of the P‐wave equation and the SV‐wave equation is analyzed and compared with other acoustic wave equations for TTI media. Using this analysis and the pseudo‐spectral method, we apply reverse‐time migration to numerical and physical‐model data. According to the comparison between the isotropic and anisotropic migration results, the anisotropic reverse‐time depth migration offers significant improvements in positioning and reflector continuity over those obtained using isotropic algorithms.     

OnP F and other phases in the early part of seismogram

Summary It has been found that when seismic energy propagates along the surface of the homogeneous crust beside usual Rayleigh waves, it produces certain instability in layers through which it propagates. In the light of this instability, a type of motion corresponding to longitudinal wave will be prominent in horizontal component compared to the vertical component; while transverse wave will be prominent in the vertical component but weak in the horizontal component, a contradiction with the existing knowledge. This has been identified withP _F phase. On taking the medium of propagation as slightly heterogeneous which allows existence of low velocity layer, a few larger number of such instabilities have been found. Velocity equation for Rayleigh waves for such media reveals existence of different velocities corresponding to vertical and horizontal components. Table for these velocities has been furnished.     

Explicit use of the Biot coefficient in predicting shear-wave velocity of water-saturated sediments

Predicting the shear‐wave (S‐wave) velocity is important in seismic modelling, amplitude analysis with offset, and other exploration and engineering applications. Under the low‐frequency approximation, the classical Biot–Gassmann theory relates the Biot coefficient to the bulk modulus of water‐saturated sediments. If the Biot coefficient under in situ conditions can be estimated, the shear modulus or the S‐wave velocity can be calculated. The Biot coefficient derived from the compressional‐wave (P‐wave) velocity of water‐saturated sediments often differs from and is less than that estimated from the S‐wave velocity, owing to the interactions between the pore fluid and the grain contacts. By correcting the Biot coefficients derived from P‐wave velocities of water‐saturated sediments measured at various differential pressures, an accurate method of predicting S‐wave velocities is proposed. Numerical results indicate that the predicted S‐wave velocities for consolidated and unconsolidated sediments agree well with measured velocities.     

不同温压条件下蛇纹岩和角闪岩中波速与衰减的各向异性

在实验室中研究了蛇纹岩和角闪岩样品在不同温压条件下的纵、横波速度和Q值．这两种岩样对应的主要组成矿物叶蛇纹石和普通角闪石都具有很强的晶格优选方位（LPO）．随着围压的增加,波速和Q值均增大,但是在相互正交的三个方向上（垂直或平行于层理面及线理方向）增大的速度并不相同,这与微裂隙的逐渐闭合密切相关．在600MPa的围压下升高温度直到600℃以上,由于微裂隙的热扩张受到约束,波速和Q值下降幅度很小．观测到的波速和Q值的各向异性具有不同的机理,波速各向异性主要与定向分布的微裂隙和主要矿物的LPO等构造因素有关;高围压下纵波Q值各向异性与速度各向异性正好相反,可能是由于形成层理面的定向排列的平板状矿物晶体沿不同方向边界之间接触程度不同造成的．     

六种不同变质程度煤的纵横波速度特征及其与密度的关系

对采自不同地区和煤矿的六种不同变质程度煤样进行常温常压条件下的超声测量.测量发现:煤的纵波与横波速度均与密度存在良好的线性正相关关系,且沿煤层走向、倾向和垂直煤层层理方向的纵横波速度逐渐降低;走向、倾向和垂向上的纵波速度与同一方向的横波速度也存在良好的线性正相关性;六种煤样三个方向间的速度各向异性一般都大于10%.通过与经典经验公式—Gardner与Castagna公式理论换算值的对比发现:由于煤层的软岩特征,理论换算煤的纵波速度、横波速度与实验室实测值之间存在较大误差.因此,在煤田地震勘探中应使用根据煤的岩石物理测试而形成的关系式.     

Experimental verification of the fracture density and shear‐wave splitting relationship using synthetic silica cemented sandstones with a controlled fracture geometry

We present laboratory ultrasonic measurements of shear‐wave splitting from two synthetic silica cemented sandstones. The manufacturing process, which enabled silica cementation of quartz sand grains, was found to produce realistic sandstones of average porosity 29.7 ± 0.5% and average permeability 29.4 ± 11.3 mD. One sample was made with a regular distribution of aligned, penny‐shaped voids to simulate meso‐scale fractures in reservoir rocks, while the other was left blank. Ultrasonic shear waves were measured with a propagation direction of 90° to the coincident bedding plane and fracture normal. In the water saturated blank sample, shear‐wave splitting, the percentage velocity difference between the fast and slow shear waves, of <0.5% was measured due to the bedding planes (or layering) introduced during sample preparation. In the fractured sample, shear‐wave splitting (corrected for layering anisotropy) of 2.72 ± 0.58% for water, 2.80 ± 0.58% for air and 3.21 ± 0.58% for glycerin saturation at a net pressure of 40 MPa was measured. Analysis of X‐ray CT scan images was used to determine a fracture density of 0.0298 ± 0.077 in the fractured sample. This supports theoretical predictions that shear‐wave splitting (SWS) can be used as a good estimate for fracture density in porous rocks (i.e., SWS = 100ε_f, where ε_f is fracture density) regardless of pore fluid type, for wave propagation at 90° to the fracture normal.