Lithology‐controlled evolution of stream bed sediment and basin‐scale sediment yields in adjacent mountain watersheds,Idaho, USA

The composition, grain‐size, and flux of stream sediment evolve downstream in response to variations in basin‐scale sediment delivery, channel network structure, and diminution during transport. Here, we document downstream changes in lithology and grain size within two adjacent ~300 km² catchments in the northern Rocky Mountains, USA, which drain differing mixtures of soft and resistant rock types, and where measured sediment yields differ two‐fold. We use a simple erosion–abrasion mass balance model to predict the downstream evolution of sediment flux and composition using a Monte Carlo approach constrained by measured sediment flux. Results show that the downstream evolution of the bed sediment composition is predictably related to changes in underlying geology, influencing the proportion of sediment carried as bedload or suspended load. In the Big Wood basin, particle abrasion reduces the proportion of fine‐grained sedimentary and volcanic rocks, depressing bedload in favor of suspended load. Reduced bedload transport leads to stronger bed armoring, and coarse granitic rocks are concentrated in the stream bed. By contrast, in the North Fork Big Lost basin, bedload yields are three times higher, the stream bed is less armored, and bed sediment becomes dominated by durable quartzitic sandstones. For both basins, the geology‐based mass balance model can reproduce within ~5% root‐mean‐square error the composition of the bed substrate using realistic erosion and abrasion parameters. As bed sediment evolves downstream, bedload fluxes increase and decrease as a function of the abrasion parameter and the frequency and size of tributary junctions, while suspended load increases steadily. Variable erosion and abrasion rates produce conditions of variable bed‐material transport rates that are sensitive to the distribution of lithologies and channel network structure, and, provided sufficient diversity in bedrock geology, measurements of bed sediment composition allow for an assessment of sediment source areas and yield using a simple modeling approach. Copyright © 2016 John Wiley & Sons, Ltd.     

Suspended sediment dynamics at high and low storm flows in two small watersheds

A record spanning almost 20 years of suspended sediment and discharge measurements on two reaches of an agricultural watershed is used to assess the influence of in‐channel sediment supplies and bed composition on suspended sediment concentrations (SSC). We analyse discharge‐SSC relationships from two small streams of similar hydrology, climate and land use but widely different bed compositions (one dominated by sand, the other by gravel). Given that sand‐dominated systems have more fine sediment available for transport, we use bed composition and the relative proportion of surface sand and gravel to be representative of in‐channel sediment supply. Both high flow events and lower flows associated with onset and late recessional storm flow (‘low flows’) are analysed in order to distinguish external from in‐channel sources of sediment and to assess the relationship between low flows and sediment supply. We find that SSC during low flows is affected by changes to sediment supply, not just discharge capacity, indicated by the variation in the discharge‐SSC relationship both within and between low flows. Results also demonstrate that suspended sediment and discharge dynamics differ between reaches; high bed sand fractions provide a steady supply of sediment that is quickly replenished, resulting in more frequent sediment‐mobilizing low flow and relatively constant SSC between floods. In contrast, SSC of a gravel‐dominated reach vary widely between events, with high SSC generally associated with only one or two high‐flow events. Results lend support to the idea that fine sediment is both more available and more easily transported from sand‐dominated streambeds, especially during low flows, providing evidence that bed composition and in‐channel sediment supplies may play important roles in the mobilization and transport of fine sediment. In addition, the analysis of low‐flow conditions, an approach unique to this study, provides insight into alternative and potentially significant factors that control fine sediment dynamics. Copyright © 2007 John Wiley & Sons, Ltd.     

Relationship between bed shear stress and suspended sediment concentration:annular flume experiments

In this study,annular flume experiments were carried out,using the sediment samples collected from the lower part of the inter-tidal zone at Xiaoyangkou,Jiangsu coast,China.The Ariathurai-Partheniades equation was used to determine the bed shear stress,by evaluating variations in the suspended sediment concentration within the water column.The derived relation between the bed shear stress and suspended sediment concentration shows that,at various stages of seabed erosion, suspended sediment concentration increases rapidly when the flow velocity is increased,but the pattern of change in the bed shear stress does not follow suit.At low concentrations,bed shear stress initially increases markedly with increasing flow velocity.However,when the concentration reaches an apparently critical level around 0.55 kg m"3,the rate of change in the bed shear stress abruptly slows down,or becomes almost constant,in response to further increases in the flow velocity.Results of experiments indicate that,from a critical level onward,suspended sediment concentration has a strong influence on the bed shear stress.     

Sediment production and yield from an alluvial gully in northern Queensland,Australia

Sediment production, transport and yield were quantified over various timescales in response to rainfall and runoff within an alluvial gully (7 · 8 ha), which erodes into dispersible sodic soils of a small floodplain catchment (33 ha) along the Mitchell River, northern Australia. Historical air photographs and recent global positioning system (GPS) surveys and LiDAR data documented linear increases in gully area and volume, indicating that sediment supply has been relatively consistent over the historic period. Daily time lapse photography of scarp retreat rates and internal erosion processes also demonstrated that erosion from rainfall and runoff consistently supplied fine washload (< 63 µm) sediment in addition to coarse lags of sand bed material. Empirical measurements of suspended sediment concentrations (10 000 to >100 000 mg/L) and sediment yields (89 to 363 t/ha/yr) were high for both Australian and world data. Total sediment yield estimated from empirical washload and theoretical bed material load was dominated by fine washload (< 63 µm). A lack of hysteresis in suspended sediment rating curves, scarp retreat and sediment yield correlated to rainfall input, and an equilibrium channel outlet slope supported the hypothesis that partially or fully transport‐limited conditions predominated along the alluvial gully outlet channel. This is in contrast to sediment supply‐limited conditions on uneroded floodplains above gully head scarps. While empirical data presented here can support future modelling efforts to predict suspended sediment concentration and yield under the transport limiting situations, additional field data will also be needed to better quantify sediment erosion and transport rates and processes in alluvial gullies at a variety of spatial and temporal scales. Copyright © 2013 John Wiley & Sons, Ltd.     

三峡水库运用后荆江段非均匀悬沙恢复特性

三峡工程运用后,坝下游荆江段来沙量大幅度减小,处于严重的不平衡输沙状态,次饱和水流冲刷河床使悬沙量沿程恢复.基于实测水沙资料,分析了三峡工程运用后荆江段非均匀悬沙恢复特点.提出了恢复效率的概念用以表征悬移质沿程恢复的程度,并根据实测水沙资料计算了荆江段1994-2017年非均匀悬沙的恢复效率.结果表明：三峡工程运用前,荆江段各粒径组悬沙恢复效率绝对值均接近0,故该时期内各粒径组泥沙冲淤幅度不大;三峡工程运用后,各粒径组悬沙恢复效率绝对值均明显增大,且粗沙（d>0.125 mm）恢复效率绝对值远大于细沙（d<0.125 mm）,故粗沙恢复程度更高.这主要是由于荆江段床沙组成中粗沙部分含量大,而细沙含量小.最后建立了三峡水库蓄水后非均匀悬沙恢复效率与来水来沙条件（来沙系数）的关系,结果表明：各粒径组悬移质恢复效率均与来沙系数呈正相关关系,全沙、细沙和中沙的决定系数（R²）分别为0.89、0.67和0.69,相关性较高,故荆江段各粒径组悬移质泥沙恢复效率较大程度上受到来水来沙条件的影响.     

Numerical modelling of alternate bar formation,development and sediment sorting in straight channels

A two‐dimensional shallow water hydro‐sediment‐morphodynamic model is applied to investigate alternate bar formation, development and sediment sorting in straight channels. The model is coupled, explicitly incorporating the flow–sediment–bed interactions by using the full mass and momentum conservation equations, which are numerically solved by a well‐balanced version of the finite volume Slope Limiter Centred (SLIC) scheme. The model is first tested against a flume experiment on alternate bars formed over a uniform sediment bed, which clearly exhibits processes of bar formation, migrating and finally approaching an equilibrium state. Then it is applied to another flume experiment on alternate bars due to non‐uniform sediment transport. The computational results are evaluated, with a focus on the longitudinal and vertical sediment sorting. It is argued for the first time that the inconsistent sediment sorting patterns observed in previous studies are determined by different sediment transport conditions, i.e. full versus partial transport. When a condition of full transport is achieved, under which all size fractions are fully mobilized and transported, the longitudinal surface sediment shows a sorting pattern of coarse‐on‐head and fine‐in‐pool, and the vertical substrate sediment exhibits an immobile‐fine‐coarse structure upwards. In contrast, for a partial transport condition, under which only finer fraction participates in the transport process, an opposite longitudinal pattern (i.e. fine‐on‐head and coarse‐in‐pool) and a different vertical structure (i.e. immobile‐coarse‐fine) are observed. Concurrently, numerical experiments with specified conditions show that the critical aspect ratio for the formation of migrating alternate bars is approximately equal to 12. With the increase of the aspect ratio, the bar length grows gradually, while the bar height increases rapidly for moderate values of the aspect ratio and then keeps nearly stable. The bar celerity, however, is weakly sensitive to the variation of this ratio. Copyright © 2016 John Wiley & Sons, Ltd.     

Particle size characteristics of suspended sediment in hillslope runoff and stream flow

This study examines the particle size characteristics of hillslope soils and fluvial suspended sediments in an agricultural catchment. Samples of surface runoff and stream flow were collected periodically and analysed for the size distributions of the effective (undispersed) sediment. This sediment was subsequently dispersed and the ultimate size distributions determined. The median effective particle size of stream suspended sediment was considerably coarser than the median ultimate particle size, indicating that most of the load included a substantial proportion of aggregates. Moreover, the proportion of fine material (i.e. silt and clay) increased, and the proportion of sand-sized material decreased, with increasing discharge. This decrease in sediment size with increased flow, which is contrary to the traditional assumption of a positive discharge/particle size relationship, is thought to reflect: (i) the influx of silt and clay, predominantly the former, originating on the catchment slopes and brought to the stream by overland flow along vehicle wheelings, roads and tracks; and (ii) erosion of fine material from the channel bed and banks. During large storms, however, the proportion of sand-sized sediment increased during the rising limb of the hydrograph, as a result of the entrainment of coarser source material from the valley floor during overbank flooding. The stream suspended sediment was finer than the catchment soils and considerably finer than material eroding from the catchment slopes during storms. The degree of clay and silt enrichment in the suspended sediments was largely the result of preferential deposition of the coarser fraction during the transport and delivery of sediment from its source to basin outlet. The data from this study confirm that a significant mode of sediment transport in fluvial systems is in the form of aggregates, and that the dispersed sediment size distribution is inappropriate for determining the transportability of sediment by flow. © 1997 by John Wiley & Sons, Ltd.     

Transport of moderately sorted gravel at low bed shear stresses: The role of fine sediment infiltration

A reliable estimation of sediment transport in gravel‐bed streams is important for various practical engineering and biological studies (e.g., channel stability design, bed degradation/aggradation, restoration of spawning habitat). In the present work, we report original laboratory experiments investigating the transport of gravel particles at low bed shear stresses. The laboratory tests were conducted under unsteady flow conditions inducing low bed shear stresses, with detailed monitoring of the bed topography using a laser scanner. Effects of bed surface arrangements were documented by testing loose and packed bed configurations. Effects of fine sediments were examined by testing beds with sand, artificial fine sand or cohesive silt infiltrated in the gravel matrix. Analysis of the experimental data revealed that the transport of gravel particles depends upon the bed arrangement, the bed material properties (e.g., size and shape, consolidation index, permeability) and the concentration of fine sediments within the surface layer of moving grains. This concentration is directly related to the distribution of fine particles within the gravel matrix (i.e., bottom‐up infiltration or bridging) and their transport mode (i.e., bedload or suspended load). Compared to loose beds, the mobility of gravel is reduced for packed beds and for beds clogged from the bottom up with cohesive fine sediments; in both cases, the bed shear stress for gravel entrainment increases by about 12%. On the other hand, the mobility of gravel increases significantly (bed shear stress for particle motion decreasing up to 40%) for beds clogged at the surface by non‐cohesive sand particles. Copyright © 2017 John Wiley & Sons, Ltd.     

Bedform development and its effect on bed stabilization and sediment transport based on a flume experiment with non-uniform sediment

Non-uniform sediment deposited in a confined, steep mountain channel can alter the bed surface composition. This study evaluates the contribution of geometric and resistance parameters to bed sta-bilization and the reduction in sediment transport. Flume experiments were done under various hydraulic conditions with non-uniform bed material and no sediment supply from upstream. Results indicate that flume channels respond in a sequence of coarsening and with the formation of bedform-roughness features such as rapids, cascades, and steps. A bedform development coefficient is introduced and is shown to increase (i.e. vertical sinuosity develops) in response to increasing shear stress during the organization process. The bedform development coefficient also is positively correlated with the critical Shields number and Manning's roughness coefficient, suggesting the evolution of flow resistance with increasing bedform development. The sediment transport rate decreases with increasing bed shear stress and bedform development, further illustrating the effect of bed stabilization. An empirical sedi-ment transport model for an equilibrium condition is proposed that uses the bedform development coefficient, relative particle submergence (i.e. the ratio of mean water depth and maximum sediment diameter), modified bed slope, and discharge. The model suggests bedform development can play a primary role in reducing sediment transport (increasing bed stabilization). The model is an extension of Lane's (1955) relation specifically adapted for mountain streams. These results explain the significance of bedform development in heightening flow resistance, stabilizing the bed, and reducing sediment transport in coarse, steep channels.     

Storage,properties and seasonal variations in fine‐grained bed sediment within the main channel and headwaters of the River Sanginjoki,Finland

Lowland catchments in Finland are intensively managed, promoting erosion and sedimentation that negatively affects aquatic environments. This study quantified fine‐grained bed sediment in the main channel and upstream headwaters of the River Sanginjoki (399.93 km²) catchment, Northern Finland, using remobilization sediment sampling during the ice‐free period (May 2010–December 2011). Average bed sediment storage in river was 1332 g m^?2. Storage and seasonal variations were greater in small headwater areas (total bed sediment storage mean 1527 g m^?2, range 122–6700 g m^?2 at individual sites; storage of organic sediment: mean 414 g m^?2, range 27–3159 g m^?2) than in the main channel (total bed sediment storage: mean 1137 g m^?2, range 61–4945 g m^?2); storage of organic sediment: mean 329 g m^?2, range 13–1938 g m^?2). Average reach‐specific bed sediment storage increased from downstream to upstream tributaries. In main channel reaches, mean specific storage was 8.73 t km^?1, and mean specific storage of organic sediment 2.45 t km^?1, whereas in tributaries, it was 126.94 and 34.05 t km^?1, respectively. Total fine‐grained bed sediment storage averaged 563 t in the main channel and 6831 t in the catchment. The proportion of mean organic matter at individual sites was 15–47% and organic carbon 4–455 g C m^?2, with both being highest in small headwater tributaries. Main channel bed sediment storage comprised 52% of mean annual suspended sediment flux and stored organic carbon comprised 7% of mean annual total organic carbon load. This indicates the importance of small headwater brooks for temporary within‐catchment storage of bed sediment and organic carbon and the significance of fine‐grained sediment stored in channels for the suspended sediment budget of boreal lowland rivers. Copyright © 2013 John Wiley & Sons, Ltd.     

Trends in suspended sediment grain size in the upper Yangtze River and its tributaries,as influenced by human activities

Abstract

Based on data from five hydrometric stations, Pingshan station on the Jinshajiang River, Gaochang station on the Minjiang River, Wulong station on the Wujiang River, Wusheng station on the Jialingjiang River and Yichang station on the Yangtze River, a study has been made of the temporal variation in grain size of suspended sediment load in the upper Yangtze River. The results show that in the past 40 years, the grain size of the suspended sediment load in the main stem and major tributaries of the upper Yangtze River has had a decreasing trend, that can be explained by the effect of reservoir construction and implementation of soil conservation measures. The reservoirs in the upper Yangtze River Basin, all used for water storage for hydro-electric generation and/or irrigation, have trapped coarse sediment from the drainage area above the dam and, thus, the sediment released now is much finer than before the construction of the reservoirs. The downstream channels are all gravel-bedded or even in bedrock, with little fine sediment, and thus, the released flow can hardly get a supply of fine sediment through eroding the bed. Then, after the downstream adjustment, the grain size of suspended sediment is still fine. Large-scale soil conservation measures have significantly reduced sediment yield in some major sediment source areas. The relatively coarse sediment is trapped and, thus, the sediment delivered to the river becomes finer.     

Formation and erosion of sediment cover in an experimental bedrock‐alluvial channel

Sediment grains in a bedrock‐alluvial river will be deposited within or adjacent to a sediment patch, or as isolated grains on the bedrock surface. Previous analysis of grain geometry has demonstrated that these arrangements produce significant differences in grain entrainment shear stress. However, this analysis neglected potential interactions between the sediment patches, local hydraulics and grain entrainment. We present a series of flume experiments that measure the influence of sediment patches on grain entrainment. The flume had a planar bed with roughness that was much smaller than the diameters of the mobile grains. In each experiment sediment was added either as individual grains or as a single sediment pulse. Flow was then increased until the sediment was entrained. Analysis of the experiments demonstrates that: (1) for individual grains, coarse grains are entrained at a higher discharge than fine grains; (2) once sediment patches are present, the different in entrainment discharge between coarse and fine grains is greatly reduced; (3) the sheltering effect of patches also increases the entrainment discharge of isolated grains; (4) entire sediment patches break‐up and are eroded quickly, rather than through progressive grain‐by‐grain erosion; (5) as discharge increases there is some tendency for patches to become more elongate and flow‐aligned, and more randomly distributed across the bed. One implication of this research is that the critical shear stress in bedrock‐alluvial channels will be a function of the extent of the sediment cover. Another is that the influence of sediment patches equalizes critical shear stresses between different grain sizes and grain locations, meaning that these factors may not need to be accounted for. Further research is needed to quantify interactions between sediment patches, grain entrainment and local hydraulics on rougher bedrock surfaces, and under different types of sediment supply. Copyright © 2016 John Wiley & Sons, Ltd.     

Patterns of grain‐size dependent sediment transport in low‐ordered,ephemeral channels

Sediment data were analyzed to determine grain‐size dependant factors affecting sediment transport in a low‐ordered, ephemeral watershed. Sediment and flow samples were collected during 22 flow events at the outlet of a 4·53 ha sub‐watershed within the Walnut Gulch Experimental Watershed in south‐eastern Arizona. Measured concentrations ranged from 4191 to 115 045 mg l^?1 and included grain sizes up to 8·0 mm in diameter. Two grain‐size dependent transport patterns were observed, that of the finer grain‐size fraction (approximately < 0·25 mm) and that of a coarser grain‐size fraction (approximately ≥ 0·25 mm). The concentration of the fine fraction decreased with flow duration, peaking near the beginning of a flow event and declining thereafter. The concentration of the fine fraction showed slight trends with season and recovery period. The concentration of the coarse fraction displayed a slight negative trend with instantaneous discharge and was not correlated with event duration. These patterns typically produced a condition where the majority of the fine fraction of the sediment yield was evacuated out of the watershed before the hydrograph peak while the majority of the coarser sediment was evacuated during the falling limb of the hydrograph. Each grain‐size dependent transport pattern was likely influenced by the source of the associated sediment. At the flow event time scale, the fines were primarily wash load, supplied from the hillslopes and the coarser grains were entrained from the channel bed. Because transport patterns differ based on grain size, attempts to define the total sediment concentration and sediment yield by the behavior of a single grain‐size fraction may lead to erroneous results, especially when a large range of sediment grain sizes are present. Copyright © 2010 John Wiley & Sons, Ltd.     

Uniform and graded bed-load sediment transport in a degrading channel with non-equilibrium conditions

Bed-load transport plays a critical role in river morphological change and has an important impact on river ecology.Although there is good understanding of the role of the variation of river bed grain size on transport dynamics in equilibrium conditions,much less is understood for non-equilibrium conditions when the channel is either aggrading or degrading.In particular,the relative role of different grain sizes in the promotion and hindering of the transport of coarse and fine fractions in a degrading channel has yet to be investigated.The current study attempts to provide new understanding through a series of flume experiments done using uniform and graded sediment particles.The experiments revealed coarser grain-size fractions for a poorly-sorted sediment,relative to uniform-sized sediment,reduced the transport of finer grains and finer fractions enhanced the transport of coarse grains.This hinderingpromotion effect,caused by relative hiding and exposure of finer and coarse fractions,increased with bed slope and decreased with relative submergence.In particular,as relative submergence increased,the graded fractions tended towards behaving more like their unifo rm-sized counterparts.Also,the bed-load parameter of the graded fractions increased more with a rise in bed slope than observed for the uniformsized counterparts.These results revealed,for degrading channel conditions,such as downstream of a dam,bed-load equations developed for uniform bed sediment are inappropriate for use in natural river systems,particularly in mountain streams.Furthermore,changes in river bed composition due to activities that enhance the input of hill-slope sediment,such as fire,logging,and agricultural development,are likely to cause significant changes in river morphology.     

Flume‐ and field‐based evaluation of a time‐integrated suspended sediment sampler for the analysis of sediment properties

Suspended sediment has been identified as a vector for nutrient and contaminant transport in the fluvial environment. A time‐integrated sampler (the Phillips sampler), which emerged over a decade ago as a cost‐effective tool for in situ suspended sediment collection, is increasingly being used to collect samples for the analysis of sediment properties such as particle size composition, and nutrient and contaminant concentrations. This study evaluates the sampler under both flume and field conditions for efficiency in the mass and grain size of the suspended sediment collected. The sampler was tested in a flume using both kaolinite and sediment samples (sieved to < 180 µm) collected from the Quesnel River, British Columbia, Canada. In the kaolinite trails, the sampler preferentially collected coarser grain sizes compared to the original sediment, probably due to finer sediment remaining in suspension and therefore passing through the sampler, and also possibly due to flocculation of the kaolinite upon introduction to the flume. Conversely, the sampler collected river sediment that was finer than the original sediment, probably due to some settling of coarser sediment observed at the bottom of the flume. Once allowance was made for these operational issues associated with the flume, maximum sediment mass efficiency for kaolinite and river sediment was 43% and 87%, respectively. Sediment collected by the time‐integrated sampler during field deployment and adjacent channel bed sediment were also compared. The sampler collected sediment with a representative grain size distribution. However, there were differences in the geochemical (arsenic and selenium) concentrations of channel bed sediment and sediment collected by the Phillips sampler which may be a function of differences in the behavior of geochemical elements associated with the two types of sediment. This work suggests that further research is needed to evaluate the role of the Phillips sampler in collecting sediment for contaminant and nutrient analysis. Copyright © 2014 John Wiley & Sons, Ltd.     

Experimental investigation of the morphodynamic response of riffles and pools to unsteady flow and increased sediment supply

Gravel-bed rivers characteristically exhibit shallow riffles in wide sections and deeper pools where the channel becomes constricted and narrow. While rivers can adjust to changing flow and sediment supply through some combination of adjustments of channel slope, bed-surface sorting, and channel shape, the degree to which riffle-pools may adopt these changes in response to changing flows and sediment supplies remains unclear. This article presents results from a flume experiment investigating how constant- and variable-width channels adjust their morphology in response to changing flow and increased sediment supply. Two flume geometries were used: (1) constant-width and (2) variable-width, characterized by a sinusoidal pattern with a mean width equal to that of the first channel. The variable-width channel developed bed undulations in phase with the width, representing riffle-pools. The experiment consisted of three phases for each flume geometry: (1) steady flow, constant sediment supply; (2) unsteady flow, constant sediment supply; and (3) unsteady flow, doubled sediment supply. Unsteady flow was implemented in the form of repeated symmetrical stepped hydrographs, with a mean discharge equal to that in the steady flow phase. In all phases the bed and sediment supply were composed of a sand/gravel mixture ranging from 1 to 8 mm. In both the straight and variable-width channels, transitioning from steady flow to repeated hydrographs did not result in significant changes in bed morphology. The two channel geometries had different responses to increased sediment supply: the slope of the straight channel increased nearly 40%, while the variable-width channel reduced the relief between bars and pools and decreased the variability in cross-sectional elevation with a slight slope increase. Bar-pool relief varied with repeat discharge hydrographs. Pool elevation changed twice the distance of bar elevations, emphasizing the relevance of pool scour for riffle-pool self-maintenance in channels with width variations.     

Interannual variation of suspended sediment load and sediment yield in an alpine catchment

Abstract

The results are described of 16 years operation of a measuring station for the automatic recording of water discharge, bed load and suspended sediment transport in the Rio Cordon catchment, a small alpine basin (5 km²) located in northeastern Italy. Hillslope erosion processes were investigated by surveying individual sediment sources repeatedly. Annual and seasonal variations of suspended sediment load during the period 1986–2001 are analysed along with their contribution to the total sediment yield. The results show that suspended load accounted for 76% of total load and that most of the suspended sediment transport occurred during two flood events: an extreme summer flash flood in September 1994 (27% of the 16-years total suspended load) and a snowmelt-induced event in May 2001 accompanied by a mud flow which fed the stream with sediments. The role of active sediment source areas is discussed in relation to the changes in flood peak—suspended load trends which became apparent after both the 1994 and the 2001 events.     

Hyperconcentrated flows as influenced by coupled wind-water processes

Hyperconcentrated flow is a natural phenomenon, which is widely observed on the Loess Plateau of China[1,2]. So far, much research has been done with hyperconcentrated flows in China[1―7], although hy-perconcentrated flows are also observed in many riv-ers in other countries[8―10]. In the monograph edited by Chien[11], hyperconcnetrated flows were studied in depth, involving the physical properties, resistance, sediment-carry behavior and channel-forming pro- cesses. Wang and Chien el al.[…     

A field investigation of the sediment transport characteristics of a high sediment load intermittent river in Taiwan

Most rivers in Taiwan are intermittent rivers with relatively steep slopes and carry rapid sediment‐laden flows during typhoon or monsoon seasons. A series of field experiments was conducted to collect suspended load data at the Tzu‐Chiang Bridge hydrological station of the lower Cho‐Shui River, which is a major river with the highest sediment yield in Taiwan. The river reach was aggrading with a high aspect ratio during the 1980s. Because of sand mining and extreme floods, it was incised and has had a relatively narrow main channel in recent years. The experimental results indicated that typical sediment transport equations can correctly predict the bed material load for low or medium sediment transport rates (e.g. less than about 1000 tons/day‐m). However, these equations far underestimate the bed material load for high sediment transport rates. The effects of cross‐sectional geometry change (i.e. river incision) and earthquakes on the sediment load were investigated in this study. An empirical sediment transport equation with consideration of the aspect ratio was also derived using the field data collected before and after river incision. Copyright © 2012 John Wiley & Sons, Ltd.     

长江中游沙质河段床沙级配调整过程计算

三峡工程运用后,长江中游荆江河段持续冲刷,床沙与推移质、悬移质泥沙不断交换,从而造成该河段床沙发生不同程度的调整,对长江中下游河床演变及非平衡输沙机理的研究具有重要影响.在新水沙条件下,总结分析了沙波运动特性及床沙交换方式,引入Markov三态转移概率及非均匀沙隐暴系数,得到基于状态转移概率的沙质河段床沙级配调整的计算模型.研究结果表明:(1)20092014年,沙市站年内床沙中值粒径有先增大后减小的趋势,而监利站年内床沙中值粒径则先减小后增大,且荆江河段年际床沙中值粒径总体呈上升趋势,粗化程度约为6.9%~9.3%;(2)20092014年,沙市站床沙组成中粒径d<0.062 mm的泥沙所占比重不变,0.062 mm≤d<0.25 mm的泥沙所占比重逐年减少(累计减少11.4%),d≥0.25 mm的泥沙所占比重逐年增加(累计增加11.4%),而监利站床沙组成均存在波动性变化;(3)荆江河段床沙转换为推移质的概率随着泥沙粒径的增大而增大,床沙转换为悬移质的概率随着泥沙粒径的增大而减小,而推移质和悬移质转换为床沙的概率均随着泥沙粒径的增大而增大,河床发生冲刷粗化时泥沙输移的主要形式为悬移质(概率为81%~87%),而淤积细化时床沙补给主要来源于推移质(概率为8%~12%).通过验证,本文概率模型的计算结果与实测资料符合较好,能够应用于长江中游沙质河段年际床沙粗化及年内床沙级配调整过程预报,为进一步开展三峡工程下游非均匀悬移质泥沙沿程恢复机理的研究提供理论基础.