高架桥地震反应半主动控制分析

本文探讨了高架桥结构地震反应LQR(Linear Quadratic Regulator)半主动控制算法以及考虑刚度退化的桥墩非线性计算模型，并利用Matlab语言编制的程序对其进行了数值仿真计算。结果表明，将隔震技术与利用MR阻尼器的半主动控制技术相结合，能够有效地减小高架桥的地震反应；MR阻尼器的设置位置以及结构的参数对控制效果有较大影响。考虑桥墩非线性影响将能得到更为接近实际的计算结果。     

ER/MR智能阻尼器对空间网壳结构地震反应的半主动控制

本文提出了ER/MR智能阻尼器对空间网壳结构地震反应半主动控制的设计计算方法.文中,在推导了ER/MR智能阻尼器杆件有限单元模型的基础上,建立了设置ER/MR智能杆件的网壳结构地震反应的运动方程.应用本文提出的局域半主动控制策略,我们得到了ER/MR智能阻尼器对空间网壳结构地震反应半主动控制的计算方法.工程实例的计算结果表明:ER/MR智能杆件是一种不会失稳的控制装置,在结构上合理布置ER/MR智能杆件和合理选取ER/MR智能杆件的参数可获得较好的减震效果.     

ER／MR智能阻尼器耦联的带裙房高层建筑结构地震反应的半主动控制

本文建立了用ER／MR智能阻尼器耦联的带裙房高层建筑结构地震反应半主动控制的设计计算方法,文中,在导出ER／MR智能阻尼器力学模型的基础上,建立了ER／MR智能阻尼器耦联的带裙房层建筑结构地震反应的基本方程,并根据瞬时最优主动控制的原则,提出了ER／MR智能阻尼器耦联的带裙房高层建筑地震反应半主动控制的基于最优主动控制位移的“开关－耗能”半主动控制策略,应用本文方法对主楼20层,裙房5层的计算结构;受控地震反应的模拟计算结构表明,耦联主楼和裙房的半主动的ER／MR智能阻尼器可有效地抑制带裙房高层建筑结构地震反应的鞭梢效应,并可均匀地减小结构各层的震反应,是一种简单,方便和有效的智能控制装置。     

安装复合MR阻尼器的结构振动台试验研究

对不同控制策略下安装有复合MR(磁流变)阻尼器的模型结构进行了振动台试验研究.在El Centro地震动激励下,基于线性二次高斯(LQG)和广义预测(GP)两种控制算法,针对半主动控制系统、MR阻尼器以恒定电流(-0.5A(Passive-on 1)、0A(Passive-off)、2A(Passive-on 2)的控制系统,以及由半主动控制方式和基础隔震组合而成的混合控制系统,在WINCON/SIMULINK实时控制软件平台下对一个1:4的三层钢框架模型进行了地震模拟振动台试验.试验结果表明:基于复合MR阻尼器的控制系统是有效的,无论是被动控制、半主动控制还是混合控制,都显著降低了模型结构各层的加速度、位移响应;复合MR阻尼器在不通入电流时具有一定的被动控制效果;采用考虑时滞自补偿的广义预测控制效果要好于LQG控制,并且这两种控制策略的都能以较被动控制小的控制力达到较好的控制效果.     

相邻结构地震反应MR阻尼器控制的仿真分析

本文仿真分析了应用磁流变(MR)阻尼器对相邻结构地震反应的控制效果,为进一步开展模型试验研究奠定了基础。建立了地震激励下相邻结构MR阻尼器控制系统的运动方程,提出了描述MR阻尼器阻尼力滞回特性的改进S igmoid模型,分别对应用开关控制、半主动控制以及最小或最大电流被动控制的四种控制方法的相邻结构地震反应的控制效果进行了仿真分析。结果表明,在相邻结构间连接安装MR阻尼器可以有效地控制相邻结构的地震反应,且开关控制方法和半主动控制方法的控制效果均好于两种被动控制方法,体现了MR阻尼器阻尼力可调的优点;在四种控制方法中,半主动控制方法的控制效果最好,体现了MR阻尼器阻尼力具有连续调节能力的优点;若能解决MR阻尼器的剩磁问题,半主动控制方法的控制效果会得到进一步的提高。     

变阻尼半主动结构控制振动台试验

在一个１：４的五层模型刚架结构上进行了变阻尼半主动结构控制振动台试验．在结构的底层安装了一个溢流阀式变阻尼控制器,输入几种不同的地震动并采用几种不同的控制算法对结构进行了变阻尼半主动控制。振动台试验结果表明,受阻尼半主动结构控制仅需要很少的电能,就可以达到较好的控制效果,是一种很有应用前景的结构振动控制方案。结合溢流阀式变阻尼控制器的特点,分析了一些因素对控制效果的影响．     

变阻尼半主动结构振动台试验

在一个1：4的五层模型刚架结构上进行了变阻尼半主动结构控制振动台试验,在结构的底层安装了一个溢流阀式变阻尼控制器,输入几种不同的地震动并采用几种不同的控制算法对结构进行了变阻尼半主动控制,振动台试验结果表明,变阻尼半主动结构控制仅需要很少的电能,就可以达到较好的控制效果,是一种很有效的前景的结构振动控制方案,结合溢流阀式变阻尼控制器的特点,分析了一些因素对控制效果的影响。     

变刚度半主动结构振动控制的试验研究

本文成功地完成了五层框架的变刚度半主动结构振动控制的模拟地震振动试验,这不仅是我国的第一个变刚度半主动结构振动控制的试验,在国际上也是少数几例之一。本文介绍了试验系统的构成,试验内容,试验结果的分析及试验结论等。     

结构地震反应的瞬时KCE控制

提出了地震作用下结构主动控制的瞬时ＫＣＥ控制，给出参数的优化确定方法，并针对某试验用模型结构进行了计算和分析。结果表明，瞬时ＫＣＥ控制算法明显优于瞬时最优控制算法。     

MR阻尼器对桅杆结构风振响应的智能半主动控制

本文基于修正的拉格朗日坐标描述法，推导了空间四节点纤绳单元的大位移刚度矩阵的具体表达式。在将桅杆结构离散为空间四节点纤绳单元和梁单元的计算模型的基础上，建立了桅杆结构非线性风振响应分析的有限元方法。根据瞬时最优主动控制的原则，提出了MR阻尼器对桅杆结构风振反应智能半主动控制基于阻尼器位移的“开关—耗能”半主动控制策略。算例结果表明MR阻尼器能有效地减小桅杆结构的风振反应。     

Semi‐active fuzzy control for seismic response reduction using magnetorheological dampers

A semi‐active fuzzy control strategy for seismic response reduction using a magnetorheological (MR) damper is presented. When a control method based on fuzzy set theory for a structure with a MR damper is used for vibration reduction of a structure, it has an inherent robustness, and easiness to treat the uncertainties of input data from the ground motion and structural vibration sensors, and the ability to handle the non‐linear behavior of the structure because there is no longer the need for an exact mathematical model of the structure. For a clipped‐optimal control algorithm, the command voltage of a MR damper is set at either zero or the maximum level. However, a semi‐active fuzzy control system has benefit to produce the required voltage to be input to the damper so that a desirable damper force can be produced and thus decrease the control force to reduce the structural response. Moreover, the proposed control strategy is fail‐safe in that the bounded‐input, bounded‐output stability of the controlled structure is guaranteed. The results of the numerical simulations show that the proposed semi‐active control system consisting of a fuzzy controller and a MR damper can be beneficial in reducing seismic responses of structures. Copyright © 2004 John Wiley & Sons, Ltd.     

Predictive control of seismic structures with semi‐active friction dampers

In this paper a predictive control method especially suitable for the control of semi‐active friction dampers is proposed. By keeping the adjustable slip force of a semi‐active friction damper slightly lower than the critical friction force, the method allows the damper to remain in its slip state throughout an earthquake of arbitrary intensity, so the energy dissipation capacity of the damper can be improved. The proposed method is formulated in a discrete‐time domain and cast in the form of direct output feedback for easy control implementation. The control algorithm is able to produce a continuous and smooth slip force for a friction damper and thus avoid exerting the high‐frequency structural response that usually exists in structures with conventional friction dampers. Using a numerical study, the control performance of a multiple degrees of freedom (DOF) structural system equipped with passive friction dampers and semi‐active dampers controlled by the proposed method are compared. The numerical case shows that by merely using a single semi‐active friction damper and a few sensors, the proposed method is able to achieve better acceleration reduction than the case using multiple passive dampers. Copyright © 2004 John Wiley & Sons, Ltd.     

Experimental and analytical study on pounding reduction of base‐isolated highway bridges using MR dampers

Pounding between adjacent superstructures has been a major cause of highway bridge damage in the past several earthquakes. This paper presents an experimental and analytical study on pounding reduction of highway bridges subjected to earthquake ground motions by using magnetorheological (MR) dampers. An analytical model, which incorporates structural pounding and MR dampers, is developed. A series of shaking table tests on a 1:20 scaled base‐isolated bridge model are performed to investigate the effects of pounding between adjacent superstructures on the dynamics of the structures. Based on the test results, the parameters of the linear and the nonlinear viscoelastic impact models are identified. Performance of the semiactive system for reducing structural pounding is also investigated experimentally, in which the MR dampers are used in conjunction with the proposed control strategy, to verify the effectiveness of the MR dampers. Structural responses are also simulated by using the established analytical model and compared with the shaking table test results. The results show that pounding between adjacent superstructures of the highway bridge significantly increases the structural acceleration responses. For the base‐isolated bridge model considered here, the semiactive control system with MR dampers effectively precludes pounding. Copyright © 2009 John Wiley & Sons, Ltd.     

Semi‐active multi‐step predictive control of structures using MR dampers

A semi‐active multi‐step predictive control (SAMPC) system with magnetorheological (MR) dampers is developed to reduce the seismic responses of structures. This system can predict the next multi‐step responses of structure according to the current state and has a function of self‐compensation for time delay that occurred in real application. To study the performance of the proposed control algorithm for addressing time delay and reducing the seismic responses, a numerical example of an 11‐story structure with MR dampers is presented. Comparison with the uncontrolled structure indicates that both the peak and the norm values of structural responses are all clearly reduced when the predictive length l?10 and the delayed time step d?20 are selected, and the SAMPC strategy can guarantee the stability of the controlled structure and reduce the effects of time delay on controlled responses to a certain extent. A performance comparison is also made between the SAMPC strategy and the passive‐off and passive‐on methods; results indicate that this SAMPC system is more effective than the two passive methods in reducing structural responses subjected to earthquakes. Copyright © 2008 John Wiley & Sons, Ltd.     

Experimental verification of seismic vibration control using a semi‐active friction tuned mass damper

A tuned mass damper (TMD) system consists of an added mass with properly functioning spring and damping elements for providing frequency‐dependent damping in a primary structure. The advantage of a friction‐type TMD, that is, a nonlinear TMD, is its energy dissipation via a friction mechanism. In contrast, the disadvantages of a passive friction TMD (PF‐TMD) are its fixed and predetermined slip load and loss of tuning and energy dissipation capabilities when it is in a stick state. A semi‐active friction TMD (SAF‐TMD) is used to overcome these disadvantages. The SAF‐TMD can adjust its slip force in response to structure motion. To verify its feasibility, a prototype SAF‐TMD was fabricated and tested dynamically using a shaking table test. A nonsticking friction control law was used to keep the SAF‐TMD activated and in a slip state in earthquakes at varying intensities. The shaking table test results demonstrated that: (i) the experimental results are consistent with the theoretical results; (ii) the SAF‐TMD is more effective than the PF‐TMD given a similar peak TMD stroke; and (iii) the SAF‐TMD can also prevent a residual TMD stroke in a PF‐TMD system. Copyright © 2011 John Wiley & Sons, Ltd.     

Experimental verification of torsional response control of asymmetric buildings using MR dampers

This paper proposes a semiactive control system to reduce the coupled lateral and torsional motions in asymmetric buildings subjected to horizontal seismic excitations. Magnetorheological (MR) dampers are applied as semiactive control devices and the control input determination is based on a clipped‐optimal control algorithm which uses absolute acceleration feedback. The performance of this method is studied experimentally using a 2‐story building model with an asymmetric stiffness distribution. An automated system identification methodology is implemented to develop a control‐oriented model which has the natural frequencies observed in the experimental system. The parameters for the MR damper model are identified using experimental data to develop an integrated model of the structure and MR dampers. To demonstrate the performance of this control system on the experimental structure, a shake table is used to reproduce an El Centro 1940 N–S earthquake as well as a random white noise excitation. The responses for the proposed control system are compared to those of passive control cases in which a constant voltage is applied to the MR damper. Copyright © 2003 John Wiley & Sons, Ltd.     

Semiactive fuzzy control of the seismic response of building frames with MR dampers

A fuzzy‐logic control algorithm, based on the fuzzification of the MR damper characteristics, is presented for the semiactive control of building frames under seismic excitation. The MR damper characteristics are represented by force–velocity and force–displacement curves obtained from the sinusoidal actuation test. The method does not require any analytical model of MR damper characteristics, such as the Bouc‐Wen model, to be incorporated into the control algorithm. The control algorithm has a feedback structure and is implemented by using the fuzzy‐logic and Simulink toolboxes of MATLAB. The performance of the algorithm is studied by using it to control the responses of two example buildings taken from the literature—a three‐storey building frame, in which controlled responses are obtained by clipped‐optimal control and a ten‐storey building frame. The results indicate that the proposed scheme provides nearly the same percentage reduction of responses as that obtained by the clipped‐optimal control with much less control force and much less command voltage. Position of the damper is found to significantly affect the controlled responses of the structure. It is observed that any increase in the damper capacity beyond a saturation level does not improve the performance of the controller. Copyright © 2011 John Wiley & Sons, Ltd.     

Semi‐active neuro‐control for base‐isolation system using magnetorheological (MR) dampers

Vibration mitigation using smart, reliable and cost‐effective mechanisms that requires small activation power is the primary objective of this paper. A semi‐active controller‐based neural network for base‐isolation structure equipped with a magnetorheological (MR) damper is presented and evaluated. An inverse neural network model (INV‐MR) is constructed to replicate the inverse dynamics of the MR damper. Next, linear quadratic Gaussian (LQG) controller is designed to produce the optimal control force. Thereafter, the LQG controller and the INV‐MR models are linked to control the structure. The coupled LQG and INV‐MR system was used to train a semi‐active neuro‐controller, designated as SA‐NC, which produces the necessary control voltage that actuates the MR damper. To evaluate the proposed method, the SA‐NC is compared to passive lead–rubber bearing isolation systems (LRBs). Results revealed that the SA‐NC was quite effective in seismic response reduction for wide range of motions from moderate to severe seismic events compared to the passive systems. In addition, the semi‐active MR damper enjoys many desirable features, such as its inherent stability, practicality and small power requirements. The effectiveness of the SA‐NC is illustrated and verified using simulated response of a six‐degree‐of‐freedom model of a base‐isolated building excited by several historical earthquake records. Copyright © 2006 John Wiley & Sons, Ltd.     

Experimental verification of a wireless sensing and control system for structural control using MR dampers

The performance aspects of a wireless ‘active’ sensor, including the reliability of the wireless communication channel for real‐time data delivery and its application to feedback structural control, are explored in this study. First, the control of magnetorheological (MR) dampers using wireless sensors is examined. Second, the application of the MR‐damper to actively control a half‐scale three‐storey steel building excited at its base by shaking table is studied using a wireless control system assembled from wireless active sensors. With an MR damper installed on each floor (three dampers total), structural responses during seismic excitation are measured by the system's wireless active sensors and wirelessly communicated to each other; upon receipt of response data, the wireless sensor interfaced to each MR damper calculates a desired control action using an LQG controller implemented in the wireless sensor's computational core. In this system, the wireless active sensor is responsible for the reception of response data, determination of optimal control forces, and the issuing of command signals to the MR damper. Various control solutions are formulated in this study and embedded in the wireless control system including centralized and decentralized control algorithms. Copyright © 2007 John Wiley & Sons, Ltd.     

Semi‐active control of sliding isolated bridges using MR dampers: an experimental and numerical study

Sliding base‐isolation systems used in bridges reduce pier drifts, but at the expense of increased bearing displacements under near‐source pulse‐type earthquakes. It is common practice to incorporate supplemental passive non‐linear dampers into the isolation system to counter increased bearing displacements. Non‐linear passive dampers can certainly reduce bearing displacements, but only with increased isolation level forces and pier drifts. The semi‐active controllable non‐linear dampers, which can vary damping in real time, can reduce bearing displacements without further increase in forces and pier drifts; and hence deserve investigation. In this study performance of such a ‘smart’ sliding isolation system, used in a 1:20 scaled bridge model, employing semi‐active controllable magneto‐rheological (MR) dampers is investigated, analytically and experimentally, under several near‐fault earthquakes. A non‐linear analytical model, which incorporates the non‐linearities of sliding bearings and the MR damper, is developed. A Lyapunov control algorithm for control of the MR damper is developed and implemented in shake table tests. Analytical and shake table test results are compared. It is shown that the smart MR damper reduces bearing displacements further than the passive low‐ and high‐damping cases, while maintaining isolation level forces less than the passive high‐damping case. Copyright © 2005 John Wiley & Sons, Ltd.