改进的遍布节理模型及其在层状岩体地下工程中的应用

基于显式有限差分程序FLAC3D,针对层状岩体建立了可以考虑其横观各向同性变形特性的遍布节理模型。通过FLAC3D程序的预留接口导入程序,将该改进的遍布节理模型中植入FLAC3D动态链接库。在此基础上进行了层状岩体变形与强度各向异性特性的研究,最后将该模型应用于龙滩水电站巨型地下硐室群的层状岩体围岩变形及破裂特征分析。研究表明,围岩变形主要表现为岩层同性面内的变形,其左右边墙变形不对称性主要受断层切割控制;围岩破坏型式以剪切破坏为主,其中岩体整体破坏受断层控制,表现为中低应力条件下的拉剪或压剪破坏;而开挖引起的岩层破坏受制于陡倾角层状岩体结构,表现为层间错动引起的剪切破坏。     

迭加断裂形成机制及其与构造应力场演化关系

地质体是在地壳演化中形成的,它是建造和构造形变的综合体。断裂化的地质体在较晚期构造力或工程载荷作用下沿已存在的断裂发生形变和位移的现象被称为迭加断裂,其形成过程即是迭加断裂作用。 本文以莫尔-库仑理论为基楚,探讨断裂发育与迭加断裂作用、构造应力场的关系,并对地质构造研究中的“断裂继承”,“断裂复活”进行定量的探讨。研究过程中承谷德振老师指导和鼓励,于此表示衷心的感谢。     

Role of shear along horizontal plane in the formation of helicoidal structures

An unusual structural paragenesis, complicated by brachyanticlines, is revealed for the first time in the sedimentary cover of the West Siberian Plate by 3D seismic surveying. These are linear (in plan view) systems of en-echelon arranged low-amplitude normal faults related to wrench faults in the basement. On different sides off a wrench fault, the planes of normal faults dip in opposite directions, forming a helicoidal structure that resembles the blades of a propeller. In the section parallel to the wrench fault, the boundaries of the beds and normal fault planes dip in opposite directions as well. In the section across the strike of the normal faults converging toward the basement, the beds take the shape of an antiform with a crest sagged along the normal faults (flower structure). This structural assembly was formed as a result of interference of stress fields of horizontal shear in the vertical plane (induced by faulting in the basement) and in the horizontal plane (caused by gravity resistance of the cover). In this case, the displacements along the normal faults develop in both the vertical and, to a greater extent, horizontal directions, so that the faults in cover are actually characterized by normal-strike-slip kinematics. The regional N-S-trending compression of the West Siberian Plate is the main cause of shearing along the NW- and NE-trending faults in the basement, which make up a rhomb-shaped system in plan view. Petroliferous brachyanticlines, whose axes, notwithstanding tectonophysical laws, are oriented in the direction close to the maximum compression axis, are known in the large wrench fault zones of Western Siberia. Our experiments with equivalent materials showed that a local stress field arising at the ends of echeloned Riedel shears within a wrench fault zone may be a cause of the formation of such brachyanticlines. The progressive elongation of Riedel shears leads to the corresponding elongation of the brachyanticlines located between their ends. The performed study has shown that the known types of interference of elementary geodynamic settings such as horizontal shear along the vertical plane + horizontal compression (transpression) and horizontal shear along the vertical plane + horizontal extension (transtension) may be supplemented by combination of horizontal shears along the vertical and horizontal planes, resulting in tectonic lamination. By analogy, we propose to name this type of interference of elementary shear settings translamination. Petroliferous helicoidal structures arise in the given geodynamic setting of translamination.     

Faults in Quaternary cover as a relfection of basement tectonics: Kolguev island,barents sea

The paper is concerned with the results of the detailed study of dislocations in the Pliocene-Quaternary loose sediments exposed as cliffs extending for ～30 km along the rectilinear shore of Kolguev Island. According to seismic data, this lineament is related to the Coastal Fault in the lower part of the sedimentary cover. A system of faults longitudinal, diagonal, and transverse relative to the shoreline is established from observations at the cliffs. Their arrangement in plan view corresponds to the geometry of the right-lateral shear zone, the axis of which almost coincides with the shoreline. This has allowed us to identify the faults as secondary disturbances in the region of dynamic effect of the Coastal Fault in the basement. The kinematics of the secondary faults and their dip azimuth are consistent with echeloned geometry in plan view. The low-angle dip of the reverse-strike-slip faults observed at the outcrops is caused by their near-surface flattening toward the subsided block. The shallow-seated dislocations are related to ductile lateral shear in the vertical plane. The lower layers of the sedimentary cover mimic the horizontal movements in the basement more closely than the upper layers. The data obtained indicate high neotectonic activity of the Barents Sea shelf and specify the geodynamic setting of the region in the Pliocene and Quaternary.     

岩体锚固效应及锚杆的解析本构模型研究

利用Mohr-Coulomb、Hoek-Brown以及Duncan-Chang理论分别分析了块状和碎块状岩体锚固后的物理效应,通过分析认为,岩体锚固后可以有效地提高岩体的凝聚力和软弱结构面的抗剪强度,增强岩体的弹性模量,改善岩体的力学性质。通过对拉拔试验测试结果分析,在一定的假设条件下,推导了锚杆与注浆体或岩体耦合情况下的解析本构方程,并对其进行了参数分析,认为提高拉拔力、增大锚杆直径和锚固段长度可以有效地改善其锚固效果,并提出了锚固临界值的概念。在前人工作的基础上,利用提出的耦合解析本构模型建立了非耦合状态下锚杆的解析本构模型,通过计算认为,该解析模型是合理的。     

Neoproterozoic collisional metamorphism in overthrust terranes of the Trans-Angarian Yenisey Ridge,Siberia

Four polymetamorphic complexes in the vicinity of regional faults in the Trans-Angarian region of the Yenisey Ridge were studied to determine their metamorphic evolution and to elucidate distinctive features of the regional geodynamic processes. Based on our geological and petrological studies using geothermobarometry and P–T path calculations, we show that a Neoproterozoic medium-pressure metamorphism of the kyanite-sillimanite type at c. 850 Ma overprinted regionally metamorphosed low-pressure andalusite-bearing rocks. A positive correlation between rock ages and P–T estimates for the kyanite-sillimanite metamorphism provides evidence for regional structural and tectonic heterogeneity. The medium-pressure recrystallization was characterized by (1) localized distribution of metamorphic zones in the area directly underlying thrust faults with a measured thickness of 2.5–8 km; (2) syntectonic formation of kyanite-bearing mineral assemblages related to thrusting; (3) gradual increase in metamorphic pressure towards the thrust faults associated with a low metamorphic field gradient (from 1–7 to 12°C/km); and (4) equally steep burial P–T paths recorded for the highest grade rocks. These specific features are typical of collisional metamorphism during overthrusting of continental blocks and are evidence of near-isothermal loading in accordance with the transient emplacement of thrust sheets. The proposed model for tectono-metamorphic evolution of the study areas due to crustal thickening at high thrusting rates and subsequent rapid exhumation explains these tectonic features. Data analysis allowed us to consider the medium-pressure kyanite-bearing metapelites as a product of collisional metamorphism, reflecting unidirectional thrusting of Siberian cratonal blocks onto Yenisey Ridge along regional deep faults (Angara, Mayakon, and Chapa areas) and by opposite movements in the zone of secondary splay faults (Garevka area).     

Late Panafrican evolution of the main Hoggar fault zones: Implications of magnetic fabric study in the In Telloukh pluton (Tin Serririne basin,Algeria)

The Late Panafrican evolution of the Hoggar shield is characterized by emplacement of magmatic intrusions and by occurrence of major shear zones separating different terranes. In Telloukh granite is close to the In Guezzam faults (western border of the Tin Serririne basin). Analysis of its visible and magnetic fabrics suggests an emplacement mode and deformation that are not related to the In Guezzam faults, but most likely to a N–S compression, an event not yet identified. Dioritic dykes crosscutting the granite have a very different magnetic fabric, which is related on the contrary to dextral strike-slip movements along the In Guezzam faults. In both cases, no visible fabric can be correlated with the magnetic fabric, which has been likely acquired during late magmatic stages. This magnetic fabric was not significantly affected by the tectonic events that took place after entire crystallization of the magma. The In Guezzam faults and the major 7°30 and 4°50 shear zones are close to intrusions such as In Telloukh dykes and the Alous En Tides and Tesnou plutons where quite similar magnetic fabrics are observed, all related with dextral strike-slip movements along these structures.     

The structure of the Tuapse shear zone according to the field tectonophysical data

The results of field structural studies of the Tuapse shear zone in the Northwest Caucasus are presented. This zone is characterized by shear displacements of various scales with a dominant horizontal shear, viz., a geodynamic type of the stress state, which leads to the formation of faults with mostly lateral displacement of wings, i.e., along the strike of the fault surface. The quantitative characteristics of the local stress conditions in the shear zone (the positions of principal axes and the Lode–Nadai coefficient) are determined on the basis of cataclastic analysis and geological indicators of the paleostresses. The differences between these characteristics are considered for the large tectonic zones. Significant spatial (areal) variations in orientations of the axes of major normal stresses in the shear zone and their local weak gentle variations are evidence of a consistent general stress direction during the formation of faults during the Late Eocene–Miocene deformation epoch.     

Late Panafrican evolution of the main Hoggar fault zones: Implications of magnetic fabric study in the In Telloukh pluton (Tin Serririne basin, Algeria)

The Late Panafrican evolution of the Hoggar shield is characterized by emplacement of magmatic intrusions and by occurrence of major shear zones separating different terranes. In Telloukh granite is close to the In Guezzam faults (western border of the Tin Serririne basin). Analysis of its visible and magnetic fabrics suggests an emplacement mode and deformation that are not related to the In Guezzam faults, but most likely to a N–S compression, an event not yet identified. Dioritic dykes crosscutting the granite have a very different magnetic fabric, which is related on the contrary to dextral strike-slip movements along the In Guezzam faults. In both cases, no visible fabric can be correlated with the magnetic fabric, which has been likely acquired during late magmatic stages. This magnetic fabric was not significantly affected by the tectonic events that took place after entire crystallization of the magma. The In Guezzam faults and the major 7°30 and 4°50 shear zones are close to intrusions such as In Telloukh dykes and the Alous En Tides and Tesnou plutons where quite similar magnetic fabrics are observed, all related with dextral strike-slip movements along these structures.     

Model of crustal block movement in the South Yakutia geodynamic testing area based on GPS data

The results of the analysis of crustal block movement obtained from the GPS data in 2009–2012 in the South Yakutia geodynamic testing area located at the junction of two major tectonic structures—the Aldan shield of the Siberian platform and the Stanovoi fold-block area—are presented. The drift of the block in the southeastern direction corresponds to the main azimuth of the strike of the activated fault systems and is consistent with the results of the geodetic observations performed in the 1970–1980s. Based on the periodic components of the complete displacement vector, hinge-type movements along the local faults are established. It is shown that, in the annual cycles, the rotational, oscillational, and translational movements of the block have a nonlinear character, and solitary strain waves are likely to be formed in the zones of activated faults.     

Recent tectonics in the northern part of the Knipovich Ridge,Atlantic ocean

The walls of the Knipovich Ridge are complicated by normal and reverse faults revealed by a high-frequency profilograph. The map of their spatial distribution shows that the faults are grouped into domains a few tens of kilometers in size and are a result of superposition of several inequivalent geodynamic factors: the shear zone oriented parallel to the Hornsunn Fault and superposed on the typical dynamics of the midocean ridge with offsets along transform fracture zones and rifting along short segments of the Mid-Atlantic Ridge (MAR). According to the anomalous magnetic field, the Knipovich Ridge as a segment of the MAR has formed since the Oligocene including several segments with normal direction of spreading separated by a multitransform system of fracture zones. In the Quaternary, the boundary of plate interaction along the tension crack has been straightened to form the contemporary Knipovich Ridge, which crosses the previously existing magmatic spreading substrate and sedimentary cover at an angle of about 45° relative to the direction of accretion. The sedimentary cover along the walls of the Knipovich is Paleogene in age and has subsided into the rift valley to a depth of 500–1000 m along the normal faults.     

冀东“长城式”金矿的成因探讨

区域构造和成矿特征研究表明,进入燕山期,华北地区开始了幔枝构造活动期,沿冀东茅山－金厂峪－肖营子EW向韧性剪切带与NNE向迁安－青龙韧性剪切带强烈活动。特别是2条韧性剪切带并汇部位的肖营子一带,岩浆大规模侵入,形成了以肖营子斑状花岗岩为主体的一系列大小侵入体。并带动变质围岩一起强烈隆升,中上元古界盖层则向外大幅度拆离滑脱,以致于轴部岩浆－变质杂岩呈揭顶式裸露,冷口－清河沿岸块就是由于受冷口断裂或反向铲状断理解活动影响,而残留在岩浆－变质杂岩之上的中元古界岩块。在岩块拆离滑脱过程中所形成的主拆离滑脱带、次级拆离滑脱带及层间滑动断裂成为较发育的构造扩容空间。主成矿期含矿流体沿构造扩容带贯入、聚集和成矿,形成一系列构造蚀变岩型、脉型矿体。新房子金矿的深部钻孔已证实了这种认识。矿体顶部的变宽及变富则是隆升过程中崩塌及风化淋滤造成的浅部表现,因此,应注意寻找深部矿体。     

NON-LINEAR FAULT BEHAVIOUR NEAR UNDERGROUND EXCAVATIONS — A BOUNDARY ELEMENT APPROACH

A boundary element model for stress/stability analysis of underground excavations in the vicinity of faults is presented. The boundary element formulation adopts the fictitious stress method for the simulation of excavation boundaries and the displacement discontinuity method for the representation of faults. The numerical model employs the Barton–Bandis non-linear joint model for the modelling of the fault behaviour and linear elastic behaviour for the rock. An incremental-iterative in situ stress relaxation algorithm is implemented for the non-linear analysis of the faults. Both deformation and peak strength models of Barton–Bandis are incorporated for modelling the mechanical behaviour of the fault. The non-linear deformation of fault considers the effects of coupling between shear and normal stresses and displacement, joint closure, joint separation, hardening followed by post-peak or residual behaviour. The peak strength model employs a mobilized non-linear shear strength envelope. The differences between linear and non-linear simulation of the fault models are discussed. A comparison of model predictions with the classical Mohr–Coulomb peak strength model with constant joint stiffness is presented. The numerical model is used for a case study of Canadian hard rock underground mine. The shear and normal displacements along the fault during four mining sequences with backfill simulation are presented and discussed.     

岩石破裂滑动过程及其声发射数值模拟

运用岩石破裂与失稳过程分析RFPA2D系统, 对滑动形成过程进行了数值模拟研究。滑动岩体似为非均匀弹 -脆岩石材料, 模拟结果再现了滑动形成从变形到破坏直至失稳的全过程及其声发射规律。     

白鹤滩水电站左岸坝肩开挖边坡稳定性分析

白鹤滩水电站左岸坝基边坡地质构造错综复杂,坡内多条陡倾断层和顺坡向错动带是控制边坡稳定性的主要因素。结合现场地质资料、监测数据及勘察认识,利用通用离散元软件UDEC建立左岸边坡开挖变形分析模型。首先在无支护开挖工况下研究主要结构面F17、LS331、LS3319上下盘岩体关键点应力及位移变化,并指出潜在失稳破坏区;同时采用预应力锚索单元在不同施工时序下对潜在不稳定块体进行加固计算,对比研究了不同方案下左岸边坡的变形破坏机制和整体稳定性。计算结果和现场监测表明：左岸边坡变形破坏与结构面密切相关,在开挖卸荷作用下主要表现为沿错动带的压剪破坏和陡倾断层的张拉破坏,采用预应力锚索加固处理能够有效提高边坡稳定性,并且在开挖后及时跟进支护可以有效抑制边坡剪切变形。研究结果对白鹤滩左岸坝基边坡后续工程加固和施工工序具有一定的参考价值。     

非贯通节理岩体直剪试验研究进展

基于典型的直剪试验,国内外学者提出了非贯通节理岩体贯通破坏机理,并建立了相应的强度准则,如Jennings方法,即加权平均强度理论和强度准则、Lajtai岩桥破坏理论和强度准则、断裂力学的II型破坏理论和强度准则,拉剪复合破坏和强度准则。然而,非贯通节理岩体破坏机理目前还没有完全弄清楚,已建立的强度准则所包含的重要参数还需深入研究,如：如节理面的传压系数、传剪系数、弱化了的岩桥内摩擦力和内摩擦角等;非贯通节理岩体节理闭合和剪切的本构关系有待建立;不共面非贯通节理岩体全过程最大抗剪强度需进一步研究。伺服直剪试验机、静态应变测试仪、声发射仪、X射线测量等无损检测技术能够为进一步研究非贯通节理岩体的破坏机理,提出新的理论和建立新的强度准则提供强有力的技术支持。     

The structural history of the Mont Blanc massif with regard to models for its recent exhumation

The tectonic evolution of the Mont Blanc range with regard to its cooling and exhumation history has been discussed and debated over many years and is still controversial. Recently, several low-temperature thermochronology studies have determined the cooling history of the massif in considerable detail and various tectonic models proposed to explain the young and fast exhumation signal established from these studies. Here we present detailed field data from the wider Mont Blanc area and assess possible exhumation processes in terms of these field constraints. Our observations indicate that none of the major faults or shear zones around the Mont Blanc massif (i.e. Mont Blanc shear zone, Mont Blanc back-thrust, Penninic thrust) was active in Late Neogene times and that young exhumation is therefore not controlled by movements along these structures. We demonstrate that the position of Mont Blanc in the bend of the western Alps plays an important role in its tectonic history and that simple 2D models are insufficient to explain its evolution. Interference between NW–SE compression and orogen-parallel extension along the Rhône-Simplon fault system resulted in a complex regional structural pattern, with strike-slip movements on both sides of the Mont Blanc massif. Young brittle faults are predominantly strike slip without significant vertical offset. The young (<2 Ma) rapid exhumation of Mont Blanc is more broadly distributed and cannot be directly linked to discrete faults bounding the massif. The mechanisms driving this recent accelerated exhumation must similarly be of broader scale.     

连通节理岩质边坡稳定性分析

节理岩体的剪切强度由结构面和相邻完整岩块的剪切强度共同决定,当结构面完全连通时,岩体的剪切强度完全由结构面决定。蒙特卡罗法能够根据结构面几何参数模拟岩体结构面的空间分布,通过深度优先搜索算法可搜索到连通的结构面,相对岩体而言,连通的结构面的剪切强度最小,即为节理岩质边坡的潜在滑动面,通过极限平衡法可以对一系列滑面进行稳定性分析。该方法是对节理岩质边坡稳定分析的补充。     

岩体结构面剪切流变试验及模型参数反演分析

针对锦屏二级水电站地下洞室群围岩富含节理的实际情况,采用弱面直剪流变仪对组成隧洞围岩的主要岩样（板岩、大理岩）进行了含软弱夹层岩石的剪切流变试验,得出岩石夹层的剪应力-剪切位移时程曲线。通过对岩石夹层试验结果的分析,得出了岩石的长期强度参数,与快剪试验获得抗剪强度参数相比较发现长期抗剪强度参数有所降低,且凝聚力对剪切流变特性的影响略高于内摩擦系数。最后通过对6种模型的拟合分析,得出了适合岩石夹层的标准线性体流变模型,在此基础上通过反演分析得到了岩石夹层标准线性体黏弹-塑性剪切流变模型,并反演了该模型的参数。     

Failure Characteristics of Complicated Random Jointed Rock Mass Under Compressive-Shear Loading

Most natural rock masses contain a large number of random joints and fissures, and most of the rock masses at the rock engineering are commonly in both compression and shear stress environment. However, the research on the failure characteristics of complex random jointed rock mass under compressive-shear loading is still limited. To address this gap, this paper uses the particle flow code 2D to establish a discrete fractured rock mass model and carry out a series of numerical tests with different compressive-shear angles (α) and different joint geometric parameters. The effects of compressive-shear angle and joint geometric parameters on the strength and failure characteristics of fractured rock masses are studied. The results indicate that with the increase of α, the peak strength of the specimen decreases gradually, and the failure mode changes from the composite shear failure mode (Mode-I) to a plane shear failure mode (Mode-II) and then to intact shear failure mode (Mode-III). Specifically, the three failure modes occur in the specimens with α?=?15°, 30° or 45°, 60°, respectively. The existence of joints affects stress distribution on rock mass during the loading process. Furthermore, the stress at the joint tip is relatively concentrated, while on both sides of the joint is smaller. Three kinds of crack coalescence patterns are observed: tensile, shear, and tensile-shear mixed coalescence. The inclination angle of the rock bridge between adjacent joints affects the specific type of coalescence.