Field Study of Vertical Screening Distance Criteria for Vapor Intrusion of Ethylene Dibromide

Several regulatory agencies recommend screening petroleum vapor intrusion (PVI) sites based on vertical screening distance between a petroleum hydrocarbon source in soil or groundwater and a building foundation. U.S. Environmental Protection Agency (U.S. EPA) indicate the risk of PVI is minimal at buildings that are separated by more than 6 feet (1.8 m) from a dissolved-phase source and 15 feet (4.6 m) from a light nonaqueous phase liquid (LNAPL) source. This vertical screening distance method is not, however, recommended at sites with leaded gasoline sources containing ethylene dibromide (EDB) because of a lack of field data to document EDB attenuation in the vadose zone. To help address this gap, depth-discrete soil-gas samples were collected at a leaded gasoline release site in Sobieski, Minnesota (USA). The maximum concentration of EDB in groundwater (175 μg/L) at the site was high relative to those observed at other leaded gasoline release sites. Soil gas was analyzed for EDB using a modification of U.S. EPA Method TO-14A that achieved analytical detection limits below the U.S. EPA Vapor Intrusion Screening Level (VISL) for EDB based on a 10⁻⁶ cancer risk (<0.16 μg/m³). Concentrations of EDB in soil gas above LNAPL reached as high as 960 μg/m³ and decreased below the VISL within a source-separation distance of 7 feet. This result coupled with BioVapor model predictions of EDB concentrations indicate that vertical screening distances recommended by regulatory agencies at PVI sites are generally applicable for EDB over the range of anticipated source concentrations and soil types at most sites.     

Simulated Soil Vapor Intrusion Attenuation Factors Including Biodegradation for Petroleum Hydrocarbons

Aerobic biodegradation can contribute significantly to the attenuation of petroleum hydrocarbons vapors in the unsaturated zone; however, most regulatory guidance for assessing potential human health risks via vapor intrusion to indoor air either neglect biodegradation in developing generic screening levels or allow for only one order of magnitude additional attenuation for aerobically degradable compounds, which may be overly conservative in some cases. This paper describes results from three-dimensional numerical model simulations of vapor intrusion for petroleum hydrocarbons to assess the influence of aerobic biodegradation on the attenuation factor for a variety of source concentrations and depths for residential buildings with basements and slab-on-grade construction. The simulations conducted in this study provide a framework for understanding the degree to which bioattenuation will occur under a variety of scenarios and provide insight into site conditions that will result in significant biodegradation. This improved understanding may be used to improve the conceptual model of contaminant transport, guide field data collection and interpretation, and estimate semi-site-specific attenuation factors for combinations of source concentrations, source depth, oxygen distribution, and building characteristics where site conditions reasonably match the scenarios simulated herein.     

1,4‐Dioxane Soil Remediation Using Enhanced Soil Vapor Extraction: I. Field Demonstration

1,4‐Dioxane is totally miscible in water, sequestering in vadose pore water that can serve as a source of long‐term groundwater contamination. Although some 1,4‐dioxane is removed by conventional soil vapor extraction (SVE), remediation is typically inefficient. SVE efficiency is hindered by low Henry’s Law constants at ambient temperature and redistribution to vadose pore water if SVE wells pull 1,4‐dioxane vapors across previously clean soil. It was hypothesized that heated air injection and more focused SVE extraction (“Enhanced SVE” or XSVE) could increase the efficiency of 1,4‐dioxane vadose treatment, and this new process was tested at former McClellan Air Force Base, CA. The XSVE system had four peripheral heated air injection wells surrounding a 6.1 m × 6.1 m × 9.1 m deep treatment zone with a central vapor extraction well. After 14 months of operation, soil temperatures reached as high as ~90 °C near the injection wells and the treatment zone was flushed with ~20,000 pore volumes of injected air. Post‐treatment sampling results showed reductions of ~94% in 1,4‐dioxane and ~45% in soil moisture. Given the simplicity of the remediation system components and the promising demonstration test results, XSVE has the potential to be a cost‐effective remediation option for vadose zone soil containing 1,4‐dioxane.     

Soil Gas Sampling for 1,4‐Dioxane during Heated Soil Vapor Extraction

Soil gas sampling for 1,4‐dioxane at elevated soil temperatures, such as those experienced during in‐situ thermal treatment, has the potential to yield low results due to condensation of water vapor in the ambient temperature sampling vessel and the partitioning of 1,4‐dioxane into that condensate. A simple vapor/condensate sampling apparatus was developed to collect both condensate and vapor samples to allow for determination of a reconstituted effective soil gas concentration for 1,4‐dioxane. Results using the vapor/condensate sampling apparatus during a heated air injection SVE field demonstration are presented, along with those of a comparable laboratory system. Substantial 1,4‐dioxane mass was found in the condensate in both the lab and field (as high as ~50% in field). As soil temperatures increased, less 1,4‐dioxane mass was detected in field condensate samples than expected based on laboratory experiments. Extraction well effluent sampling at the wellhead by direct vapor canister sampling provided erratic results (several biased low by a factor of 5 or more) compared to those of the vapor/condensate apparatus. Direct vapor canister sampling of extraction well effluent after the air‐water separator, however, provided results reasonably comparable (within 35%) to those using the vapor/condensate apparatus at the wellhead. Soil gas sampling at elevated temperatures using the vapor/condensate apparatus alleviates potential low sampling bias due to condensation.     

Multimedia Risk-Based Soil Cleanup at a Gasoline-Contaminated Site Using Vapor Extraction

At a utility service center, gasoline from an underground storage tank had leaked into subsurface vadose zone soils for several years. To remediate the site, a soil vapor extraction (SVE) system was installed and operated. At the completion of the SVE operation, gasoline-containing residues in several confirmation soil borings exceeded agency-mandated cleanup levels. Rather than continue with SVE, a risk-based approach was developed to evaluate what levels of gasoline-containing residues could be left in the soil and still protect human health. The risk-based approach consisted of simulating the fate of chemical residues through the vadose zone and then into both the ground water and atmosphere. Receptor point concentrations were predicted, and health risks were assessed. The risk assessment concluded that ingestion of contaminated ground water and inhalation of air while showering were the largest potential contributors to risk, and that risks associated with inhalation of vapor-containing ambient air are small. However, all predicted risks are below the acceptable risk levels of 10⁻⁶ individual cancer risk probability and 1.0 hazard index. Therefore, the lead agency accepted the recommendation that the site requires no further remediation. The service center continues normal operations today.     

Estimation of Generic Subslab Attenuation Factors for Vapor Intrusion Investigations

Generic indoor air:subslab soil gas attenuation factors (SSAFs) are important for rapid screening of potential vapor intrusion risks in buildings that overlie soil and groundwater contaminated with volatile chemicals. Insufficiently conservative SSAFs can allow high‐risk sites to be prematurely excluded from further investigation. Excessively conservative SSAFs can lead to costly, time‐consuming, and often inconclusive actions at an inordinate number of low‐risk sites. This paper reviews two of the most commonly used approaches to develop SSAFs: (1) comparison of paired, indoor air and subslab soil gas data in empirical databases and (2) comparison of estimated subslab vapor entry rates and indoor air exchange rates (IAERs). Potential error associated with databases includes interference from indoor and outdoor sources, reliance on data from basements, and seasonal variability. Heterogeneity in subsurface vapor plumes combined with uncertainty regarding vapor entry points calls into question the representativeness of limited subslab data and diminishes the technical defensibility of SSAFs extracted from databases. The use of reasonably conservative vapor entry rates and IAERs offers a more technically defensible approach for the development of generic SSAF values for screening. Consideration of seasonal variability in building leakage rates, air exchange rates, and interpolated vapor entry rates allows for the development of generic SSAFs at both local and regional scales. Limitations include applicability of the default IAERs and vapor entry rates to site‐specific vapor intrusion investigations and uncertainty regarding applicability of generic SSAFs to assess potential short‐term (e.g., intraday) variability of impacts to indoor air.     

Development of a Default Vapor Intrusion Attenuation Factor for Industrial Buildings

An investigation at a major industrial facility in the Midwestern United States provides insights regarding the amount of attenuation of sub-surface vapors occurring at industrial buildings. The buildings at the facility were ranked in terms of vapor intrusion potential and testing began in October 2016 and is ongoing. Results have been evaluated for data collected at 718 unique locations across 77 buildings. A total of 1646 sample pairs (sub-slab and indoor air) have been collected and analyzed for 65 analytes, resulting in a total of 106,990 data pairs. As many as 49 sample pairs were collected within a given building during a single sampling event and up to 11 rounds of seasonal testing have been performed at selected buildings. Seasonal variability in sub-slab soil-gas concentrations was found to be negligible. Data analysis was performed to look for data trends across the entire data set and identify inter-building comparisons. This data evaluation focused on individual volatile organic compounds (e.g., tetrachloroethylene, trichloroethylene) present in the sub-slab soil gas at concentrations exceeding 1000 μg/m³. A total of 157 building-specific attenuation coefficients (α) were evaluated. This evaluation demonstrated that large industrial buildings have a much greater attenuation than that assumed for single-family residential buildings. All attenuation coefficient values were lower than 0.03, which is the standard regulatory default for non-residential buildings. The median value was 9.3E-05 and the 95% upper confidence limit was 2.7E-04. There is some evidence of lower attenuation under wintertime conditions. The data suggests that the default attenuation factor of 0.03 over-predicts indoor air impacts at this industrial facility by at least two orders of magnitude.     

The Influence of Surface Covers on the Performance of a Soil Vapor Extraction System

This study looks at the influence of surface covers on the performance of a single pumping well system. Pilot tests were conducted on a sandy soil to determine the influence of surface confinement based upon both induced vacuum and pore gas velocity design criteria. The results demonstrate how covering the surface can significantly alter the associated air flow patterns and velocity distribution. Comparison of streamline iso‐contours obtained in covered scenarios reveals that the surface seal tended to prevent air from entering the subsurface near the extraction well and force air to be drawn from a greater distance. Calculated and measured pressure differentials, for open and semi‐confined scenarios, clearly show that adding a clay layer as a surface cover increased the vacuum induced within the soil. Pore gas velocity analysis showed that when the cover clay layer was used, the zone of capture of the soil vapor extraction system increased. The radius of influence of soil vapor extraction (SVE) systems, based on the attainment of a critical vacuum or pore gas velocity, can then be increased by including a surface seal in the design of such systems. The focus of this study is limited to air flow patterns contrasted between covered and uncovered conditions and not on the nuances of a full scale remediation implementation.     

Utility of Compound‐Specific Isotope Analysis for Vapor Intrusion Investigations

Different types of data can be collected to evaluate whether or not vapor intrusion is a concern at sites impacted with volatile organic compound (VOC) contamination in the subsurface. Typically, groundwater, soil gas, or indoor air samples are collected to determine VOC concentrations in the different media. Sample results are evaluated using a “multiple lines of evidence” approach to interpret whether vapor intrusion is occurring. Data interpretation is often not straightforward because of many complicating factors, particularly in the evaluation of indoor air. More often than not, indoor air sample results are affected by indoor or other background sources making interpretation of concentration‐based data difficult using conventional sampling approaches. In this study, we explored the practicality of compound‐specific isotope analysis (CSIA) as an additional type of evidence to distinguish between indoor sources and subsurface sources (i.e., vapor intrusion). We developed a guide for decision‐making to facilitate data interpretation and applied the guidelines at four different test buildings. To evaluate the effectiveness of the CSIA method for vapor intrusion applications, we compared the interpretation from CSIA to interpretations based on data from two different investigation approaches: conventional sampling and on‐site GC/MS analysis. Interpretations using CSIA were found to be generally consistent with the other approaches. In one case, CSIA provided the strongest line of evidence that vapor intrusion was not occurring and that a VOC source located inside the building was the source of VOCs in indoor air.     

A New Analytical Treatment of Airflow to Inlet Wells in Soil Vapor Extraction Systems

This paper provides a new analytical model of airflow to inlet wells in soil vapor extraction systems. It is based on a recent analytical solution of airflow to a single vapor extraction well by Bahr and Joss (1995), which updated the previous model of Baehr and Hult (1991). Baehr and Joss (1995) treated the air leakage through the surface as an air flux boundary condition, whereas Baehr and Hult (1991) approximated the leakage as a distributed source imposed in the governing airflow equation. The new analytical model shows significant improvement on air-flow assessment over the previous model by Ge and Liao (1996), which could underestimate the efficiency of airflow to inlet wells by as much as 27% in a typical vapor extraction system.     

Analysis of Soil Vapor Extraction Data to Evaluate Mass-Transfer Constraints and Estimate Source-Zone Mass Flux

Methods are developed to use data collected during cyclic operation of soil vapor extraction (SVE) systems to help characterize the magnitudes and time scales of mass flux associated with vadose zone contaminant sources. Operational data collected at the Department of Energy’s Hanford site are used to illustrate the use of such data. An analysis was conducted of carbon tetrachloride vapor concentrations collected during and between SVE operations. The objective of the analysis was to evaluate changes in concentrations measured during periods of operation and nonoperation of SVE, with a focus on quantifying temporal dynamics of the vadose zone contaminant mass flux, and associated source strength. Three mass flux terms, representing mass flux during the initial period of an SVE cycle, during the asymptotic period of a cycle, and during the rebound period, were calculated and compared. It was shown that it is possible to use the data to estimate time frames for effective operation of an SVE system if a sufficient set of historical cyclic operational data exists. This information could then be used to help evaluate changes in SVE operations, including system closure. The mass flux data would also be useful for risk assessments of the impact of vadose zone sources on groundwater contamination or vapor intrusion.