隔震与非隔震支座对混凝土箱梁桥地震易损性的影响

为评估隔震和非隔震支座对桥梁地震易损性的影响,以一座3跨连续混凝土箱梁桥为分析对象,首先建立采用铅芯橡胶隔震支座与非隔震型盆式橡胶支座下桥梁的数值模型,求得不同程度地震作用下墩顶与支座的最大位移响应;再定义转角延性比损伤指标,结合支座剪应变,分析桥墩和支座的地震易损性情况;最后通过宽界限法建立全桥地震易损性曲线.研究结...     

Optimal design of superelastic‐friction base isolators for seismic protection of highway bridges against near‐field earthquakes

The seismic response of a multi‐span continuous bridge isolated with novel superelastic‐friction base isolator (S‐FBI) is investigated under near‐field earthquakes. The isolation system consists of a flat steel‐Teflon sliding bearing and a superelastic NiTi shape memory alloy (SMA) device. The key design parameters of an S‐FBI system are the natural period of the isolated bridge, the yielding displacement of the SMA device, and the friction coefficient of the sliding bearings. The goal of this study is to obtain optimal values for each design parameter by performing sensitivity analysis of a bridge isolated by an S‐FBI system. First, a three‐span continuous bridge is modeled as two‐degrees‐of‐freedom with the S‐FBI system. A neuro‐fuzzy model is used to capture rate‐ and temperature‐dependent nonlinear behavior of the SMA device. Then, a set of nonlinear time history analyses of the isolated bridge is performed. The variation of the peak response quantities of interest is shown as a function of design parameters of the S‐FBI system and the optimal values for each parameter are evaluated. Next, in order to assess the effectiveness of the S‐FBI system, the response of the bridge isolated by the S‐FBI system is compared with the response of the non‐isolated bridge and the same bridge isolated by pure‐friction (P‐F) sliding isolation system. Finally, the influence of temperature variations on the performance of the S‐FBI system is evaluated. The results show that the optimum design of a bridge with the S‐FBI system can be achieved by a judicious specification of design parameters. Copyright © 2010 John Wiley & Sons, Ltd.     

应用SMA复合橡胶支座的桥梁隔震

本文提出了一种基于形状记忆合金的复合橡胶支座（简称SMA复合橡胶支座）的智能桥梁隔震系统，应用SMA复合橡胶支座对一受El Centro地震激励的多跨简支桥的一标准跨进行了时程分析，并与应用普通橡胶支座进行了减震、隔震效果的比较，结果表明，应用SMA复合橡胶支座隔震，不仅能取得更为显著的减震、隔震效果，而且能使地震后隔震桥梁的梁体得以复位，从而验证了SMA复合橡胶支座在桥梁隔震中的有效性、智能性和自恢复能力。     

Seismic performance of cable-sliding friction bearing system for isolated bridges

During past strong earthquakes, highway bridges have sustained severe damage or even collapse due to excessive displacements and/or very large lateral forces. For commonly used isolation bearings with a pure friction sliding surface, seismic forces may be reduced but displacements are often unconstrained. In this paper, an alternative seismic bearing system, called the cable-sliding friction bearing system, is developed by integrating seismic isolation devices with displacement restrainers consisting of cables attached to the upper and lower plates of the bearing. Restoring forces are provided to limit the displacements of the sliding component. Design parameters including the length and stiffness of the cables, friction coefficient, strength of the shear bolt in a fixed-type bearing, and movements under earthquake excitations are discussed. Laboratory testing of a prototype bearing subjected to vertical loads and quasi-static cyclic lateral loads, and corresponding numerical finite element simulation analysis, were carried out. It is shown that the numerical simulation shows good agreement with the experimental force-displacement hysteretic response, indicating the viability of the new bearing system. In addition, practical application of this bearing system to a multi-span bridge in China and its design advantages are discussed.     

考虑支座滑移及挡块破坏的中小跨径梁桥地震易损性研究

从板式橡胶支座及混凝土挡块抗震设计角度,以一座典型的3跨预应力混凝土连续梁桥为例,结合概率地震需求分析及桥墩、支座等抗震关键构件极限破坏状态,建立不同支座及挡块分析模型的中小跨径梁桥地震易损性曲线,研究考虑支座滑移效应及挡块破坏的中小跨径梁桥的易损性特征。研究结果表明：不考虑橡胶支座的滑移效应及混凝土挡块破坏,桥墩地震破坏概率明显增大,且会低估支座破坏概率;桥梁系统易损性受支座破坏状态的影响显著,需设置合理的限位装置;在中小跨径梁桥地震易损性分析中,考虑支座的滑移效应及混凝土挡块的破坏十分必要。     

公民科学素质视角下的防震减灾科普研究——以日本和美国为例

防震减灾科普教育是提升公民防震减灾科学素质的重要途经。日本和美国是在防震减灾科普教育方面走在世界前列的国家。本文通过研究日本和美国关于公民防震减灾科学素质建设文献资料,分类归纳日本和美国公民防震减灾科学素质建设的历史背景、发展特点及主要路径,由此对我国公民防震减灾科学素质建设提出思考和建议。     

采用SMA拉索的摇摆自复位桥墩试验研究与动力分析

为了提升桥梁结构的抗震韧性,提出了一种采用超弹性形状记忆合金（SMA）拉索的摇摆自复位桥墩。首先对单根SMA拉索进行变幅循环拉伸试验,随后以SMA拉索的预张拉应力为试验参数,针对新型桥墩开展缩尺模型试验,详细考察了试件的力学行为与损伤模式,讨论了桥墩的滞回曲线和复位能力;提出了新型桥墩的初步设计建议,并利用OpenSees进行非线性时程分析验证。研究表明:得益于摇摆机制以及SMA拉索良好的可恢复变形性能,桥墩试件在4%滑移率内几乎不产生损伤;与传统梁桥相比,采用SMA拉索桥墩的新型梁桥可有效降低结构残余变形以及桥墩本身的损伤。虽然最大变形有所放大,但仍处在可控范围。     

Performance of seismic‐isolated bridges with and without elastic‐gap devices in near‐fault zones

In this paper, the efficiency of providing elastic‐gap devices (EGDs) to improve the performance of seismic‐isolated bridges (SIBs) in near‐fault (NF) zones is investigated. The device is primarily made of an assembly of circular rubber bearings and steel plates to provide additional elastic stiffness to the SIB upon closure of a gap. The EDG is intended to function at two performance levels under service and maximum considered design level (MCDL) NF earthquakes to reduce isolator displacements while keeping the substructure forces at reasonable levels. A parametric study, involving more than 500 nonlinear time history analyses of realistic and simplified structural models of typical SIBs, is conducted using simulated and actual NF ground motions to investigate the applicability of the proposed solution. It is found that providing EGD is beneficial for reducing the isolator displacements to manageable ranges for SIBs subjected to MCDL NF ground motions regardless of the distance from the fault and characteristics of the isolator. It is also found that providing EGD resulted in an improved performance of the isolators in terms of the reduction of heat generated by the isolators. Further analyses conducted using a realistic structural model of an existing bridge and five NF earthquakes confirmed that EGD may be used to reduce the displacement of the isolators while keeping the substructure base shear forces at reasonable ranges for SIBs located in NF zones. Copyright © 2008 John Wiley & Sons, Ltd.     

超弹性-复摩擦摆隔震支座的性能试验与数值模拟

利用复摩擦支座（Double friction pendulum bearing,DFPB）和形状记忆合金（Shape Memory alloy,SMA）拉索,提出了一种超弹性-复摩擦支座（Superelastic-double friction pendulum bearing,SDFPB）。该新型滑动隔震支座在水平方向可适应多水准地震激励,且在竖向拥有抵抗拉拔的功能。阐述了SDFPB的构造特点和工作原理。通过性能试验考察了这一隔震装置的力学特性。建立了SDFPB的恢复力模型,利用其模拟了试验条件下的滞回响应。研究结果表明:SDFPB的耗能能力优良,且具有较好的多级抗震自适应能力;模拟值与试验值吻合较好,验证了上述力学模型的正确性。     

An advanced numerical model of elastomeric seismic isolation bearings

The nuclear accident at Fukushima Daiichi in March 2011 has led the nuclear community to consider seismic isolation for new large light water and small modular reactors to withstand the effects of beyond design basis loadings, including extreme earthquakes. The United States Nuclear Regulatory Commission is sponsoring a research project that will quantify the response of low damping rubber (LDR) and lead rubber (LR) bearings under loadings associated with extreme earthquakes. Under design basis loadings, the response of an elastomeric bearing is not expected to deviate from well‐established numerical models, and bearings are not expected to experience net tension. However, under extended or beyond design basis shaking, elastomer shear strains may exceed 300% in regions of high seismic hazard, bearings may experience net tension, the compression and tension stiffness will be affected by isolator lateral displacement, and the properties of the lead core in LR bearings will degrade in the short‐term because of substantial energy dissipation. New mathematical models of LDR and LR bearings are presented for the analysis of base isolated structures under design and beyond design basis shaking, explicitly considering both the effects of lateral displacement and cyclic vertical and horizontal loading. These mathematical models extend the available formulations in shear and compression. Phenomenological models are presented to describe the behavior of elastomeric isolation bearings in tension, including the cavitation and post‐cavitation behavior. The elastic mechanical properties make use of the two‐spring model. Strength degradation of LR bearing under cyclic shear loading due to heating of lead core is incorporated. The bilinear area reduction method is used to include variation of critical buckling load capacity with lateral displacement. The numerical models are coded in OpenSees, and the results of numerical analysis are compared with test data. The effect of different parameters on the response is investigated through a series of analyses. Copyright © 2014 John Wiley & Sons, Ltd.     

SMA负刚度双曲面减震装置的优化及抗震性能研究

SMA负刚度双曲面隔震装置的试验结果表明：绕支座布置的SMA索在支座转弯处不能自由滑动,导致SMA索的受力与设计目标严重不符。为解决上述问题,拟提出一种优化升级的SMA负刚度双曲面减震装置。基于某一连续梁桥,比较研究了正刚度、零刚度与该负刚度装置的抗震性能。结果表明：该优化装置具有良好的耗能能力、自恢复性能以及强震下的限位能力。与正刚度装置及零刚度装置相比,该装置具有更好的抗震性能。     

SMA绞线-叠层橡胶复合支座振动台试验研究

对一组SMA绞线-叠层橡胶复合支座进行了振动台试验。根据试验结果比较分析了SMA绞线-叠层橡胶复合支座与普通叠层橡胶支座的隔震性能,着重分析了位移幅值对支座工作性能基本参数如等效水平刚度、最大恢复力、单位循环耗能和等效阻尼比的影响以及这些参数的变化规律。从而证明了在罕遇地震作用下发生较大水平位移幅值时,SMA绞线-叠层橡胶复合支座比普通叠层橡胶支座可提供更大的恢复力和阻尼,更有利于阻隔地震对上部结构的作用和强震作用后上部结构的自动复位。     

SMA复合支座-巨型框架结构体系减震效果分析

在研究形状记忆合金（SMA）绞线-叠层橡胶复合支座基础上,本文提出了SMA复合支座-巨型框架减震结构体系,建立了SMA复合支座-巨型框架减震结构体系的计算模型和运动方程,研究了该结构的动力反应特性,并将其与普通巨型框架结构、应用普通橡胶支座巨型框架结构进行了非线性时程对比分析。结果表明,SMA复合支座-巨型框架减震结构体系能有效地减小结构的地震响应,同时避免了地震时主次结构之间产生碰撞破坏。     

Effects of vertical excitation on the seismic performance of a seismically isolated bridge with sliding friction bearings

A finite element model is constructed for a sliding friction bearing in a seismically isolated bridge under vertical excitation with contact/friction elements. The effects of vertical excitation on the seismic performance of a seismically isolated bridge with sliding friction bearings and different bearing friction coefficients and different stiffness levels (pier diameter) are discussed using example calculations, and the effects of excitation direction for vertical excitation on the analysis results are explored. The analysis results shows that vertical excitation has a relatively large impact on seismic performance for a seismically isolated bridge with sliding friction bearings, which should be considered when designing a seismically isolated bridge with sliding friction bearings where vertical excitation dominates.     

Pounding of superstructure segments in isolated elevated bridge during earthquakes

Past severe earthquakes indicate that pounding may cause considerable damage or even lead to collapse of colliding structures. The aim of this paper is to present an analysis of pounding between superstructure segments of an isolated elevated bridge induced by the propagating seismic wave. High-damping rubber bearings (HDRBs), used as isolation devices, are modelled by proposed non-linear formulation and the significance of the bearings model for pounding is indicated. The results of the study show that pounding leads to the increase or decrease of the forces acting on piers, depending on the gap size between superstructure segments. © 1998 John Wiley & Sons, Ltd.     

地震作用下简支梁桥支座-挡块-桥墩相互作用研究

为了提高中小跨径简支梁桥的抗震能力,促进多级抗震设计思想的完善,以汶川地震中的寿江大桥为背景,构建了支座-挡块-桥墩相互作用分析模型,采用增量动力分析（IDA）方法,以挡块强度和墩高作为变化参数,研究了支座滑移、挡块限位和桥墩塑性三者之间抗震性能状态的耦合关系。研究表明:提高挡块强度可有效地控制支座的滑移,但会增大桥墩的曲率延性系数,且桥墩越矮,曲率延性系数增长越快;随着挡块强度的变化,支座滑移比的变化幅度明显大于桥墩曲率延性系数;随着墩高的增大,挡块的相对限位能力会提高;对于中小跨径简支梁桥而言,理想的抗震状态为:允许挡块破坏,使得支座出现小幅滑移,桥墩出现可修复的塑性损伤。因此,在挡块设计中,可优先考虑支座的限位效果,再综合考虑桥墩的地震响应,当桥墩为矮墩时,挡块的设计强度不可过大。     

设置负刚度装置的大跨长联连续梁桥地震反应分析

为完善大跨长联连续梁桥的减震和隔震技术,提出将负刚度装置引入某带有摩擦摆支座隔震的大跨长联连续梁桥中组成新型减震和隔震系统。基于CSIBridge软件建立全桥有限元模型,负刚度装置采用弹性多段线模拟,摩擦摆支座采用双线性恢复力模型,输入7条地震波进行了非线性时程分析,考查了新型减震和隔震系统下桥梁结构的地震反应,探究了负刚度系统对大跨长联隔震连续梁桥地震反应的影响。研究结果表明：在大跨长联隔震连续梁桥上布置负刚度装置后,梁体加速度及支座位移可被有效降低,近场地震动下的墩底内力也有明显减小。负刚度装置可有效提高大跨长联摩擦摆支座连续梁桥的抗震性能,负刚度装置也适用于大跨长联隔震连续梁桥。     

基于状态空间法的SMA-复合支座隔震结构分析

研究了SMA(shape memory alloy)绞线-叠层橡胶复合支座的工作原理,将结构控制理论中的结构状态空间法应用到该复合支座隔震结构的数值模拟分析中。建立了普通框架、安装叠层橡胶支座和安装SMA复合支座框架的结构状态方程,应用SIMULINK工具箱建立结构仿真模型,得出不同条件下框架结构的时程反应曲线。通过对比分析可以看出SMA-复合支座能很好地改变结构的隔震效果,应用状态空间法进行SMA-复合支座隔震结构的数值模拟分析简单准确。     

多维多点激励下考虑支座摩擦滑移及结构碰撞的非规则桥梁抗震性能研究

以一座典型山区非规则梁桥为研究对象,建立了该桥梁多维多点激励下的多自由度动力计算模型,研究了该桥梁在多维多点激励下考虑支座摩擦滑移及结构碰撞等非线性因素时的抗震性能。研究结果表明:相比一维地震输入,多维地震可使结构的动力响应增加,桥墩底部弯矩需求增大;相比一致激励,多点激励可使得支座的位移需求增大,且地震波最后到达的桥墩上方支座位移最大;同时考虑多点激励和碰撞效应可使桥墩的弯矩需求增加;水平地震作用下,矮墩上部的支座容易滑动,且双向地震较单向地震更明显,三向地震输入较双向有所增强。因此,对山区非规则梁桥进行抗震设计时应有针对性地进行多维多点地震输入计算,找出结构的最大地震需求,以期指导设计。     

Investigation of the seismic response of high‐rise buildings supported on tension‐resistant elastomeric isolation bearings

In many applications of seismic isolation, such as in high‐rise construction, lightweight construction, and structures with large height‐to‐width aspect ratios, significant tension forces can develop in bearings, raising concerns about the possible rupture of elastomeric bearings and the uplift of sliding bearings. In this paper, a novel tension‐resistant lead plug rubber bearing (TLRB) with improved tension‐resisting capabilities is developed and experimentally and numerically assessed. This TLRB consists of a common lead plug rubber bearing (LRB) and several helical springs. After describing the theory underlying the behavior of the TLRB, the mechanical properties of reduced‐scale prototype bearings are investigated through extensive horizontal and vertical loading tests. The test results indicate that TLRBs can improve the shear stiffness and tension resistance capacity even under significant tensile loads. A series of shaking table tests on scaled models of high‐rise buildings with different aspect ratios were conducted to investigate the dynamic performance of the TLRB and the seismic responses of base‐isolated high‐rise buildings. Three different cases were considered in the shaking table tests: a fixed base condition and the use of TLRB and LRB isolation systems. The results of the shaking table test show that (a) base‐isolated systems are effective in reducing the structural responses of high‐rise buildings; (b) an isolated structure's aspect ratio is an important factor influencing its dynamic response; (c) TLRBs can endure large tensile stresses and avoid rupture on rubber bearings under strong earthquakes; and (d) the experimental and numerical results of the responses of the models show good agreement. Copyright © 2016 John Wiley & Sons, Ltd.