基于修正应力法的横观各向同性摩尔-库仑准则及被动土压力公式

采用修正应力法考虑各向异性对土的抗剪强度的影响,该方法引入组构张量调整不同方向应力分量的相对大小,使得各向异性土在修正应力空间中等效成各向同性土。用修正应力张量代替真实应力张量,就能将摩尔-库仑强度准则发展至横观各向同性,公式的形式不发生改变,强度参数仍为与加载方向无关的常量。通过对比根据3种不同的修正应力公式得到的内摩擦角与加载方向的关系曲线,分析了组构值对内摩擦角变化规律的影响,在偏平面上绘出了连续规则的强度包线,并预测了不同各向异性岩土类材料的三轴压缩和真三轴试验结果。最后,根据横观各向同性摩尔-库仑准则计算水平沉积地层中挡土墙上的被动土压力,得到了简洁的显式表达式,验证了修正应力法的实用性。     

基于SMP的岩土各向异性强度准则

基于SMP准则,假定材料的摩擦角随沉积面和SMP的夹角而变化,通过主应力空间和物理空间的变换,将SMP的法向量变换到物理空间,以沉积面和SMP的最小夹角α为参数提出了一个各向异性强度峰值Mα。从而得到一个各向异性强度准则,适用于横观各向同性岩土材料,通过试验条件下的数据验证表明,该各向异性强度准则能够较好地描述各向异性土的强度变化规律。     

一种适用于各向异性土体的破坏准则

自然界的土体通常具有各向异性的特点,而传统的破坏准则大多只适用于各向同性的土体。结合应力张量和反映材料各向异性状态的组构张量,定义了修正偏应力及其不变量,提出了适用于各向异性土体材料的破坏准则。给出了共轴条件下正交各向异性和横向各向异性材料在一般应力空间的破坏曲线以及不同应力区中主应力系数b与摩擦角的关系曲线,并分析了它们的特性以及与各向同性材料相应曲线的区别。通过与真三轴试验数据的比较,表明该准则能很好地描述各向异性土体材料的强度特点。     

软黏土的各向异性临界状态模型

剑桥模型只适用于正常固结软黏土,不能描述不等向固结土的应力-应变行为的各向异性特性。基于剑桥模型,在其椭圆屈服面中引入各向异性张量和一个形状参数,建立了一个各向异性屈服面,提出了一个适用于等向和不等向固结软黏土的本构模型。各向异性张量的初始值由初始固结应力状态确定,其演化过程由一个与塑性剪应变和塑性体应变都有关的硬化法则描述。形状参数的引入保证了各向异性屈服面的灵活性和适应性。通过对Boston Blue黏土、高岭土和Otaniemi黏土的三轴试验结果的模拟,验证了模型的模拟能力。     

考虑饱和黏土初始各向异性的循环边界面塑性模型

天然土体的初始各向异性通常可对其后继循环特性产生显著影响。现有考虑循环载荷作用的土体弹塑性模型,往往采用类似修正剑桥模型的椭圆形屈服面,已有研究表明,该椭圆形屈服面因其拉伸弹性区域偏大,针对天然K0固结状态的土体,其计算精度较差。基于新近提出的广义各向同性硬化准则,在边界面方程中引入初始各向异性张量,并采用空间滑动面破坏准则（SMP）的变换应力法,建立了能考虑饱和黏土初始各向异性的循环边界面塑性模型。分别针对等压和偏压固结的饱和黏土静、动三轴试验进行模拟,结果表明,该模型能合理反映土体的初始各向异性及其后继循环动力特性。     

初始应力各向异性结构性土的二元介质模型

天然岩土材料具有结构性和各向异性。在岩土破损力学的理论框架下,建立了初始应力各向异性结构性土的二元介质模型。岩土破损力学把结构性岩土材料抽象成由胶结强的胶结块（胶结元）和无胶结的软弱带（摩擦元）组成的二元结构体,变形过程中胶结块逐步破损并向软弱带转化。假定胶结块为横观各向同性的理想弹脆性体,胶结块破损后转化成的软弱带为可用邓肯-张模型描述的非线性弹性体。通过引入考虑各向异性影响的破损率和局部应变系数,建立了初始应力各向异性结构性土的二元介质本构模型,并给出了模型参数的确定方法。最后给出了模型的表现,且通过人工制备初始应力各向异性结构性土的三轴压缩试验结果验证了模型的适用性。计算结果表明,所提出的本构模型可以较好地模拟初始应力各向异性结构性土的应力-应变和体积变形特性。     

基于微结构张量理论的柱状节理岩体各向异性强度分析

复杂的结构面是控制岩体力学性质的主要因素,由结构面引起的岩体各向异性一直是岩体力学研究的热点问题。柱状节理是一类特殊的岩体地质结构面,具有强烈的各向异性特性,微结构张量理论是目前国际岩石力学领域一种较有效地探讨结构面各向异性问题的新方法。材料的微结构张量和加载向量是微结构张量法描述的两个重要参量。采用多组节理面局部坐标系与整体坐标系的投影关系,定义了材料的微结构张量计算方法,引入各向异性参数ψ表述微结构张量在加载方向的投影,将其引入Jaeger针对岩体沿节理面滑动破裂提出的基于Mohr-Coulomb强度准则,得到了多组节理岩体的各向异性强度准则。同时,结合白鹤滩坝址区的柱状节理特性,分析柱状节理引起的各向异性对坝址区稳定性的影响     

一种适用于饱和黏土循环动力分析边界面塑性模型的隐式积分算法

修正了传统隐式回映算法,建立了适用于饱和黏土循环动力分析的边界面塑性模型的完全隐式积分格式。该模型基于无弹性域概念和临界状态理论,采用各向同性、运动硬化准则、旋转的边界面,并引入表征土体结构损伤和重塑程度的损伤变量以反映循环载荷作用下饱和黏土的各向异性、刚度、强度软化及塑性变形累积等特征。针对等压固结 和偏压固结 的饱和高岭黏土的不排水三轴试验进行模拟,采用不同的应变增量步长进行计算,并与试验数据对比,结果表明,修正隐式回映算法应用于该类边界面模型的合理性、积分格式的精确性和稳定性;另外,结合有限元软件自动时间步长的增量迭代解法,对饱和黏土应力控制的不排水动三轴试验进行预测,结果表明,修正的适用于该边界面的塑性模型隐式回映算法可以得到比较合理的数值分析结果,能够反映饱和黏土的循环刚度的退化和强度的弱化等动力特性。     

沉积岩的一种各向异性模型

给出了沉积岩的一种各向异性模型。用一个各向异性参数描述这类材料的固有各向异性，各向异性参数和单轴抗压强度是一个分布函数，其分布用一个微结构张量和加载方向表示。建立了一个描述各向异性沉积岩变形过程的全塑性模型。用该模型对这一些三轴试验进行了模拟，结果表明该模型能有效地描述沉积岩的固有各向异性。     

宏-细观结合的砂土单剪试验非共轴特性分析

针对传统本构理论无法描述土体单剪试验非共轴变形的不足,采用非共轴修正模型进行改进。模型基于材料状态相关临界状态理论,采用宏-细观结合的方法,将1个新的各向异性状态变量引入本构模型来描述砂土的各向异性。考虑细观组构张量和应力张量的几何关系的变化,模型可以描述砂土在主应力轴旋转条件下材料状态的变化,材料状态变化直接导致模型的硬化规律和剪胀性发生变化,因此,模型可以描述该条件下原生向异性对砂土变形的影响。引入非共轴理论对本构模型进行修正,建立了三维非共轴各向异性模型。单剪试验的加载条件会造成主应力轴相对土体沉积面发生旋转,修正模型不但能够描述砂土在主应力轴旋转条件下其原生各向异性对变形的影响,而且可以描述主应力轴旋转造成的应力诱发各向异性对土体变形的影响,因此,该模型能够对整个单剪试验的变形规律进行描述,而且物理意义清晰。通过铝棒堆积体和Toyoura砂单剪试验验证表明,非共轴修正各向异性模型能对单剪试验的整个变形过程进行较好的模拟。     

Anisotropic UH model for soils based on a simple transformed stress method

A simple method called anisotropic transformed stress (ATS) method is proposed to develop failure criteria and constitutive models for anisotropic soils. In this method, stress components in different directions are modified differently in order to reflect the effect of anisotropy. It includes two steps of mapping of stress. First, a modified stress tensor is introduced, which is a symmetric multiplication of stress tensor and fabric tensor. In the modified stress space, anisotropic soils can be treated to be isotropic. Second, a TS tensor is derived from the modified stress tensor for the convenience of developing anisotropic constitutive models to account for the effect of intermediate principal stress. By replacing the ordinary stress tensor with the TS tensor directly, the unified hardening model is extended to model the anisotropic deformation of soils. Anisotropic Lade's criterion is adopted for shear yield and shear failure in the model. The form of the original model formulations remains unchanged, and the model parameters are independent of the loading direction. Good agreement between the experimental results and predictions of the anisotropic unified hardening model is observed. Copyright © 2016 John Wiley & Sons, Ltd.     

An anisotropic strength criterion for jointed rock masses and its application in wellbore stability analyses

In this paper, an anisotropic strength criterion is established for jointed rock masses. An orientation distribution function (ODF) of joint connectivity, is introduced to characterize the anisotropic strength of jointed rock masses related to directional distributed joint sets. Coulomb failure condition is formulated for each plane of jointed rock masses by joint connectivity, where the friction coefficient and cohesion of the jointed rock mass are related to those of the intact rock and joint and become orientation dependent. When approximating joint connectivity by its second‐order fabric tensor, an anisotropic strength criterion is derived through an approximate analytical solution to the critical plane problem. To demonstrate the effects of joint distribution on the anisotropic strength of jointed rock masses, the failure envelopes are worked out for different relative orientations of material anisotropy and principal stress axes. The anisotropic strength criterion is also applied to wellbore stability analyses. It is shown that a borehole drilled in the direction of the maximum principal in situ stress is not always the safest due to the anisotropic strength of the jointed rock mass. Copyright © 2007 John Wiley & Sons, Ltd.     

Constitutive modelling of granular materials using a contact normal-based fabric tensor

This paper presents a fabric tensor-based bounding surface model accounting for anisotropic behaviour (e.g. the dependency of peak strength on loading direction and non-coaxial deformation) of granular materials. This model is developed based on a well-calibrated isotropic bounding surface model. The yield surface is modified by incorporating the back stress which is proportional to a contact normal-based fabric tensor for characterising fabric anisotropy. The evolution law of the fabric tensor, which is dependent on both rates of the stress ratio and the plastic strain, rules that the material fabric tends to align with the loading direction and evolves towards a unique critical state fabric tensor under monotonic shearing. The incorporation of the evolution law leads to a rotational hardening of the yield surface. The anisotropic critical state is assumed to be independent of the initial values of void ratio and fabric tensor. The critical state fabric tensor has the same intermediate stress ratio (i.e. b value) and principal directions as the critical state stress tensor. A non-associated flow rule in the deviatoric plane is adopted, which is able to predict the non-coaxial flow naturally. The stress–strain relation and fabric evolution of model predictions show a satisfactory agreement with DEM simulation results under monotonic shearing with different loading directions. The model is also validated by comparing with laboratory test results of Leighton Buzzard sand and Toyoura sand under various loading paths. The comparison results demonstrate encouraging applicability of the model for predicting the anisotropic behaviour of granular materials.

     

A simple method to describe three-dimensional anisotropic failure of soils

In order to describe the anisotropic failure of soils caused by the internal fabric, isotropic failure criterion should be generalized to be anisotropic. This paper achieves the generalization by introducing a simple method, called anisotropic transformed stress method, which apparently differs from the common way. Physical interpretation of this method are analyzed further. Using this method, many existing isotropic criteria can become anisotropic in the same way, and will be expressed by a unified formula finally. To verify this method, anisotropic Unified Strength Criterion is used to predict the peak strength of anisotropic soils in different loading conditions.     

A micromechanics-based model for estimating localized failure with effects of fabric anisotropy

This paper presents a micromechanics-based approach to investigate the effects of fabric anisotropy on the behavior of localized failure in granular materials. Based on a micromechanical analysis, the origin of deviatoric stress is decomposed into two components: contact force anisotropy and fabric anisotropy. Using a micro–macro approach, the back stress is interpreted as an contribution to the change of the fabric’s principal direction. The evolution of the back stress is deduced from the stress–fabric relationship and determined with reference to the deviation of the principal directions between the rate of the reduced stress tensor and the actual reduced stress tensor. With this micro–macro framework, a mixed (isotropic–kinematic) hardening model is developed based on the classical isotropic hardening theory. A laboratory simple shear test is first analyzed to validate the proposed model and illustrate the kinematic-hardening mechanism which is usually displayed under non-proportional loading. The analysis further focuses on the anisotropic aspect of localized failure. It has been discovered that the fabric anisotropy can play an important role in the occurrence of shear banding. An increasing degree of fabric anisotropy tends to delay the initiation of the strain localization and result in higher failure strength. The effects of fabric anisotropy have also been illustrated by comparing the theoretical predictions and measured results on the shear band inclination angle, shear strain level and dilatancy at bifurcation.     

A critical state sand plasticity model accounting for fabric evolution

Fabric and its evolution need to be fully considered for effective modeling of the anisotropic behavior of cohesionless granular sand. In this study, a three‐dimensional anisotropic model for granular material is proposed based on the anisotropic critical state theory recently proposed by Li & Dafalias [2012], in which the role of fabric evolution is highlighted. An explicit expression for the yield function is proposed in terms of the invariants and joint invariants of the normalized deviatoric stress ratio tensor and the deviatoric fabric tensor. A void‐based fabric tensor that characterizes the average void size and its orientation of a granular assembly is employed in the model. Upon plastic loading, the material fabric is assumed to evolve continuously with its principal direction tending steadily towards the loading direction. A fabric evolution law is proposed to describe this behavior. With these considerations, a non‐coaxial flow rule is naturally obtained. The model is shown to be capable of characterizing the complex anisotropic behavior of granular materials under monotonic loading conditions and meanwhile retains a relatively simple formulation for numerical implementation. The model predictions of typical behavior of both Toyoura sand and Fraser River sand compare well with experimental data. Copyright © 2013 John Wiley & Sons, Ltd.     

A hypoplastic model for granular soils incorporating anisotropic critical state theory

It is well known that soil is inherently anisotropic and its mechanical behavior is significantly influenced by its fabric anisotropy. Hypoplasticity is increasingly being accepted in the constitutive modeling for soils, in which many salient features, such as nonlinear stress-strain relations, dilatancy, and critical state failure, can be described by a single tensorial equation. However, within the framework of hypoplasticity, modeling fabric anisotropy remains challenging, as the fabric and its evolution are often vaguely assumed without a sound basis. This paper presents a hypoplastic constitutive model for granular soils based on the newly developed anisotropic critical state theory, in which the conditions of fabric anisotropy are concurrently satisfied along with the traditional conditions at the critical state. A deviatoric fabric tensor is introduced into the Gudehus-Bauer hypoplastic model, and a scalar-valued anisotropic state variable signifying the interplay between the fabric and the stress state is used to characterize its impact on the dilatancy and strength of the soils. In addition, fabric evolution during shearing can explicitly be addressed. Modifications have also been undertaken to improve the performance of the undrained response of the model. The anisotropic hypoplastic model can simulate experimental tests for sand under various combinations of principle stress direction, intermediate principal stress (or mode of shearing), soil densities, and confining pressures, and the associated drastic effect of different principal stress orientations in reference to the material axes of anisotropy can be well captured.