Structural investigation of the synthetic CaAn(PO4)2 (An = Th and Np) cheralite-like phosphates

The crystallographic structures of the synthetic cheralite, CaTh(PO₄)₂, and its homolog CaNp(PO₄)₂ have been investigated by X-ray diffraction at room temperature. Rietveld analyses showed that both compounds crystallize in the monoclinic system and are isostructural to monazite LnPO₄ (Ln = La to Gd). The space group is P2₁/n (I.T. = 14) with Z = 2. The refined lattice parameters of CaTh(PO₄)₂ are a = 6.7085(8) Å, b = 6.9160(6) Å, c = 6.4152(6) Å, and β = 103.71(1)° with best fit parameters R _wp = 4.87%, R _p = 3.69% and R _B = 3.99%. For CaNp(PO₄)₂, we obtained a = 6.6509(5) Å, b = 6.8390(3) Å, c = 6.3537(8) Å, and β = 104.12(6)° and R _wp = 6.74%, R _p = 5.23%, and R _B = 6.05%. The results indicate significant distortions of bond length and angles of the PO₄ tetrahedra in CaTh(PO₄)₂ and to a lesser extent in CaNp(PO₄)₂. The structural distortions were confirmed by Raman spectroscopy of CaTh(PO₄)₂. A comparison with the isostructural compounds LnPO₄ (Ln = Ce and Sm) confirmed that the substitution of the large rare earth trivalent cations with Ca²⁺ and Th⁴⁺ introduces a distortion of the PO₄ tetrahedra.     

High-pressure and high-temperature Raman spectroscopic study of hydrous wadsleyite (β-Mg2SiO4)

In situ Raman spectra of hydrous wadsleyite (β-Mg₂SiO₄) with ~1.5 wt% H₂O, synthesized at 18 GPa and 1,400°C, have been measured in an externally heated diamond anvil cell up to 15.5 GPa and 673 K. With increasing pressure (at room temperature), the three most intense bands at ~549, 720 and 917 cm⁻¹ shift continuously to higher frequencies, while with increasing temperature at 14.5 GPa, these bands generally shift to lower frequencies. The temperature-induced frequency shifts at 14.5 GPa are significantly different from those at ambient pressure. Moreover, two new bands at ~714 and ~550 cm⁻¹ become progressively significant above 333 and 553 K, respectively, and disappear upon cooling to room temperature. No corresponding Raman modes of these two new bands were reported for wadsleyite at ambient conditions, and they are thus probably related to thermally activated processes (vibration modes) at high-pressure and temperature conditions.     

Experimental determination of activity-composition relations in Ni2SiO4− Mg2SiO4 and Co2SiO4-Mg2SiO4 olivine solid solutions at 1200 K and 0.1 MPa and 1573 K and 0.5 GPa

Activity-composition relations in the olivine solid solutions Ni₂SiO₄⁻ -Mg₂SiO₄ and Co₂SiO₄-Mg₂SiO₄ have been determined at 1200 K and 0.1 MPa and at 1573 K and 0.5 GPa by equilibration with the corresponding oxide solutions. Both olivine solutions show small positive deviations from ideal (two site) mixing, which, within the limits of accuracy of the method, may be described by the simple regular solution model with parameters W_Ni+Mg^ol= 0.35 ± 1.0 kJ/g-atom and W_Co-Mg^ol = 1.37 ± 0.9 kJ/g-atom. The requirements of internal consistency between the two systems also show that the recent determination by Brousse et al. (1984) of the enthalpy of formation of Mg₂SiO₄is to be preferred over earlier work, and that their value is also probably more accurate than the uncertainty in their own measurements indicates; activities in the NiO-MgO system are close to ideal.     

Development of a facility for analysis of natural ~(32)Si

The use of peat and sediment cores to reconstruct historical trends in levels of environmental contamination, or to provide palaeoclimatic information, depends critically on the development of accurate chronologies. Radionuclides have been exploited in th…     

The nonlinear elasticity and related properties of anhydrous and hydrous γ-Mg2SiO4: a theoretical study

The second-order elastic constants up to 30 GPa, which encompass the stability field of the spinel forms, their pressure derivatives and the third-order elastic constants of both hydrous and anhydrous -Mg₂SiO₄ have been obtained theoretically. A combination of deformation theory and finite strain elasticity theory has been employed to arrive at the expressions for second-order and third-order elastic constants from the strain energy of the lattice. The strain energy is calculated by taking into account the interactions up to second nearest neighbours in the -Mg₂SiO₄ lattice. This is then compared with the strain-dependent lattice energy from continuum model approximation to obtain the expression of elastic constants. The second-order elastic constants C_ij compare favourably with the measurements in the case of anhydrous as well as hydrous -Mg₂SiO₄ and with other calculations on the anhydrous phase. All the third-order elastic constants of both the compounds are negative. The third-order elastic constant C₁₄₄(–52.41 and –45.07 GPa for anhydrous and hydrous -Mg₂SiO₄, respectively) representing the anisotropy of shear mode has a smaller value than C₁₁₁ (–2443.94 and –2101.25 GPa for anhydrous and hydrous phases, respectively), which corresponds to the longitudinal mode. The pressure-induced variations in the longitudinal elastic constants (i.e.,dC₁₁/dp) are relatively large (4.08 and 4.09 for dry and hydrous ringwoodite, respectively) compared with those for the shear (0.22 and 0.32 for dry and hydrous ringwoodite, respectively) and off-diagonal constants (1.40 and 1.41 for dry and hydrous ringwoodite, respectively). The variation of the shear moduli C_s and anisotropy factor A with pressure have also been studied. The average value of elastic anisotropy is 0.835 in the case of anhydrous -Mg₂SiO₄ and 0.830 in the hydrous phase. The reversal of sign of the Cauchy pressure C₁₂ – C₄₄, which describes the angular character of atomic bonding in metals and other compounds, at around 21 GPa for both the compounds may be a precursor to the phase transition from ringwoodite to periclase and perovskite at an elevated temperature. The aggregate elastic properties like the adiabatic bulk modulus K (175.4 and 150.2 GPa for anhydrous and hydrous phases, respectively), and the isotropic compressional (P) and shear (S) wave velocities were calculated and the mode Grüneisen Parameters (GPs) of the acoustic waves were determined based on the quasi-harmonic approximation. The low temperature limit of both hydrous and anhydrous phases of -Mg₂SiO₄ are positive (1.69 and 1.78, respectively, for hydrous and anhydrous phases) and hence we expect the thermal expansion to be positive down to absolute zero. The Anderson–Grüneisen parameter obtained for hydrous as well as anhydrous phases of -Mg₂SiO₄ from the second-order and third-order elastic constants are 2.30 and 2.29, respectively.     

Phase equilibria in the silica-undersaturated part of the KAlSiO4– Mg2SiO4– Ca2SiO4– SiO2– F system at 1 atm and the larnite-normative trend of melt evolution

The evolution of nephelinitic melts in equilibrium with mica-bearing liquidus assemblages and melting relations have been studied on two silica-undersaturated joins of the KAlSiO₄– Mg₂SiO₄– Ca₂SiO₄– SiO₂– F system at atmospheric pressure by quench runs in sealed platinum capsules. Fluorine has been added to the batch compositions by the direct exchange of fluorine for oxygen (2F⁻ = O²⁻). The first join is the pseudo-ternary Forsterite – Diopside – KAlSiO₃F₂ system. Forsterite, diopside, F-phlogopite and leucite crystallisation fields and a fluoride-silicate liquid immiscibility solvus are present on the liquidus surface of the join. Sub-liquidus and sub-solidus phases include akermanite, cuspidine, spinel, fluorite and some other minor fluorine phases. The second system is the pseudo-binary Akermanite – F-phlogopite join that intersects the Forsterite – Diopside – KAlSiO₃F₂ join. Akermanite, forsterite, diopside, F-phlogopite, leucite and cuspidine are found to crystallise on the join. Forsterite (fo) and leucite (lc) are related to F-phlogopite (phl) by a reaction with the fluorine-bearing liquid: fo + lc + l = phl, and the reaction proceeds until forsterite or leucite are completely consumed. The reaction temperature and resulting phase association depend on batch composition. Thus, leucite is not stable in the sub-solidus of the Akermanite – F-phlogopite join, but is preserved in a part of the Forsterite – Diopside – KAlSiO₃F₂ system where forsterite reacts out, or does not crystallise at all. The phlogopite-in reaction has an important effect on the composition of the coexisting liquid. The liquids initially saturated in forsterite evolve to extremely Ca rich, larnite-normative residuals. The experimental data show that larnite-normative melilitolites can crystallise from evolved melilititic melts generated from “normal” melanephelinitic parental magmas with no normative larnite. The evolution towards melilitites requires fractionation of phlogopite-bearing assemblages under volatile pressure. Received: 3 June 1997 / Accepted: 5 January 1998     

High-pressure elastic behavior of Ca4La6(SiO4)6(OH)2 a synthetic rare-earth silicate apatite: a powder X-ray diffraction study up to 9.33 GPa

The compression behavior of a synthetic Ca₄La₆(SiO₄)₆(OH)₂ has been investigated to about 9.33 GPa at 300 K using in situ angle-dispersive X-ray diffraction and a diamond anvil cell. No phase transition has been observed within the pressure range investigated. The values of zero-pressure volume V ₀, K ₀, and $K_{0}^{'}$ refined with a third-order Birch–Murnaghan equation of state are V ₀ = 579.2 ± 0.1 Å³, K ₀ = 89 ± 2 GPa, and $K_{0}^{'} = 10.9 \pm 0.8$ . If $K_{0}^{'}$ is fixed at 4, K ₀ is obtained as 110 ± 2 GPa. Analysis of axial compressible modulus shows that the a-axis (K _a0 = 79 ± 2 GPa) is more compressible than the c-axis (K _c0 = 121 ± 7 GPa). A comparison between the high-pressure elastic response of Ca₄La₆(SiO₄)₆(OH)₂ and the iso-structural calcium apatites is made. The possible reasons of the different elastic behavior between Ca₄La₆(SiO₄)₆(OH)₂ and calcium apatites are discussed.     

EPR investigation of NO2 and CO2 − and other radicals in beryl

A number of different impurities are located in the open channels of natural beryl crystals. The rare Maxixe beryl contains an unusual amount of NO₂. The isoelectronic CO₂ ⁻ radical is found in the irradiated Maxixe-type beryl. The NO₂ radicals are distributed in the Be–Al plane of the crystal, with the nitrogen atom close to the oxygens of the beryl cavity wall. These oxygens repel the negative CO₂ ⁻ radical, which is located at the center of the beryl cavity and rotates around its O–O axis, which is parallel to the crystal c-axis. When there is a nearby alkali ion at the center of the beryl channel, it reorients the CO₂ ⁻ radical so that its bisector is parallel to the c-axis and points toward the positive ion. Different signals are analyzed for Li⁺, Na⁺, and another counter-ion, which probably is Cs⁺. The related NO₃ and CO₃ ⁻ radicals are the color centers in the investigated deep blue beryls. The slow decay of the color, which makes these beryls useless as gem stones, is related to the decay of the hydrogen atoms which are present in these crystals. Evidence is given that NO₃ is created in Maxixe beryl by a natural process, while CO₃ ⁻ in Maxixe-type beryl has been created by irradiation. The temperature dependence of the EPR signals of these two radicals was investigated, but a definitive proof that they rotate at the center of the beryl cavity could not be given. EPR signals from some other radicals in beryl have been observed and described.     

Polymorphism of As4S3 (tris-(μ2-sulfido)-tetra-arsenic): accurate structure refinement on natural α- and β-dimorphites and inferred room temperature thermodynamic properties

An accurate structure refinement, using single-crystal X-ray diffraction data, on natural α- and β-dimorphites collected at Solfatara di Pozzuoli, in the Phlegraean Fields, near Naples and at Vesuvius (Italy) is reported. Theoretical calculations at various levels of sophistication have been used to calculate molecular vibrational frequencies and gas-phase specific heats, to analyze the crystal packing, and to estimate lattice energies of both phases. All computational methods contribute to demonstrate that the β-phase is the thermodynamically stable one at room temperature.     

Hydrostatic compression of γ-(Mg0.6, Fe0.4)2SiO4 to 50.0 GPa

The bulk modulus, K ₀, and its pressure derivative K₀, of -(Mg_0.6, Fe_0.4)₂SiO₄ have been accurately determined to 50.0 GPa under hydrostatic conditions at room temperature in a diamond cell using synchrotron radiation. Our results agree with Brillouin and ultrasonic measurements on -Mg₂SiO₄ at low pressure, indicating normal elastic behaviour in the metastable pressure range of this high pressure mineral. Our values of K ₀ and k₀ are 183.0 GPa and 5.4, respectively.     

A combined IR and XRD study of natural well crystalline goethites (α-FeOOH)

Acta Geochimica - Goethite (α-FeOOH) is one of the most abundant minerals on the Earth surface, occurring in temperate, tropical and equatorial climates. Fe in goethite can be substituted by...     

Radon as a “Deterministic” indicator of natural and industrial geodynamic processes

Doklady Earth Sciences -     

Discovery of a Huge Early Permian Reef Zone and Its Significance in theTethyan Evolution

AhugeEarlyPermianorganicreefzonehasbeendiscoveredrecentlyintheEastKunlunMts.ofsouthernXinjiang,duringajointgeologicalsurveyofChina--France.Thereefzonecropsoutonbothlimbsofacompoundsynclinewhichisabout25-50kmwideinSNdirection,andextendsabout300kminEWdirection,fromtheBuhadabanPeaktothewesternAqikekuleLake,whichformsthemainridgeoftheEastKunlunMts.Thestrataofthereefzoneare3000-4000minthickness,whichfarexceedsthatofPermianreefspreviouslyreportedinChina,e.g.ca.100mthickinthenorthwesternHunan…     

Mg-Fe partitioning between silicate spinel and magnesiowüstite at high pressure: experimental determination and calculation of phase relations in the system Mg2SiO4-Fe2SiO4

 Mg-Fe partitioning experiments between (Mg,Fe)₂SiO₄ spinel and (Mg,Fe)O magnesiowüstite were carried out at pressures of 17–21.3 GPa at temperatures of 1400 and 1600 °C, using a multi-anvil apparatus, in order to determine interaction parameters of spinel and magnesiowüstite solid solutions and also to constrain the equilibrium boundaries of the postspinel transition in the Fe-rich side in the system Mg₂SiO₄-Fe₂SiO₄. The obtained values of the interaction parameters were 3.4 ± 1.5 and 13.9 ± 1.4 kJ mol⁻¹, respectively, for spinel and magnesiowüstite solid solutions at 19 GPa and 1600 °C. The partitioning data in the system Mg₂SiO₄-Fe₂SiO₄ at 1400 and 1600 °C showed that the transition boundary between spinel and the mixture of magnesiowüstite and stishovite has a negative dP/dT slope. Using the above interaction parameters and available thermodynamic data of the Mg₂SiO₄ and Fe₂SiO₄ end members, the transition boundaries of spinel to the mixture of magnesiowüstite and stishovite were calculated. Within the uncertainties of the data used, the calculated boundaries are in good agreement with the boundaries at 1400 and 1600 °C experimentally determined in this study. The dissociation boundary of Fe₂SiO₄ spinel to wüstite and stishovite, calculated from the thermodynamic data, has a negative slope of −1.5 ± 0.6 MPa K⁻¹. Received: 18 February 1998 / Revised, accepted: 18 October 1999     

β(Mg0.9, Fe0.1)2SiO4: Single crystal structure,cation distribution,and properties of coordination polyhedra

The synthesis boundaries of the phase transformation; ++ in (Mg_0.9, Fe_0.1)SiO₄, have been clarified at temperatures to 2000° C and pressures up to 20 GPa in order to synthesize single crystals of high quality. A single crystal of (Mg_0.9, Fe_0.1)₂SiO₄ was grown successfully to a size of 500 m. The crystal structure has been refined from single-crystal X-ray intensities. The ferrous ions prefer M1 and M3 sites to over the larger M2 site. The volume change of all the occupied polyhedra does not contribute to the decrease of total volume in the transformation; rather it tends to increase the bulk volume through the expansion of occupied tetrahedra. The volume reduction in the phase transformations is accounted for by unoccupied polyhedra, with the octahedra contributory 60% and the tetrahedra 40% to the V of the transition. The volume change in the transformation is caused also partly by the volume decrease of MO ₆ (25%), partly the unoccupied tetrahedra (45%) and octahedra (30%).     

Hydrogen incorporation into forsterite in Mg2SiO4–K2Mg(CO3)2–H2O and Mg2SiO4–H2O–C at 7.5–14.0 GPa

Experiments on water solubility in forsterite in the systems Mg₂SiO₄–K₂Mg(CO₃)₂–H₂O and Mg₂SiO₄–H₂O–C were conducted at 7.5–14.0 GPa and 1200–1600 °C. The resulting crystals contain 448 to 1480 ppm water, which is 40–70% less than in the forsterite–water system under the same conditions. This can be attributed to lower water activity in the carbonate-bearing melt. The water content of forsterite was found to vary systematically with temperature and pressure. For instance, at 14 GPa in the system forsterite–carbonate–H₂O the H₂O content of forsterite drops from 1140 ppm at 1200 °C to 450 ppm at 1600 °C, and at 8 GPa it remains constant or increases from 550 to 870 ppm at 1300–1600 °C. Preliminary data for D-H-bearing forsterite are reported. Considerable differences were found between IR spectra of D-H- and H-bearing forsterite. The results suggest that CO₂ can significantly affect the width of the olivine-wadsleyite transition, i.e., the 410-km seismic discontinuity, which is a function of the water content of olivine and wadsleyite.     

Solubility of Ca6[Al(OH)6]2(CrO4)3·26H2O,the chromate analog of ettringite; 5–75°C

Ca₆[Al(OH)₆]₂(CrO₄)₃·26H₂O, the chromate analog of the sulfate mineral ettringite, was synthesized and characterized by X-ray diffraction, Fourier transform infra-red spectroscopy, thermogravimetric analyses, energy dispersive X-ray spectrometry, and bulk chemical analyses. The solubility of the synthesized solid was measured in a series of dissolution and precipitation experiments conducted at 5–75°C and at initial pH values between 10.5 and 12.5. The ion activity product (IAP) for the reaction Ca₆[Al(OH)₆]₂(CrO₄)₃·26H₂O⇌6Ca²⁺+2Al(OH)⁻₄+3CrO²⁻₄+4OH⁻+26H₂O varies with pH unless a CaCrO_4(aq) complex is included in the speciation model. The log K for the formation of this complex by the reaction Ca²⁺+CrO²⁻₄=CaCrO_4(aq) was obtained by minimizing the variance in the IAP for Ca₆[Al(OH)₆]₂(CrO₄)₃·26H₂O. There is no significant trend in the formation constant with temperature and the average log K is 2.77±0.16 over the temperature range 5–75°C. The log solubility product (log K_SP) of Ca₆[Al(OH)₆]₂(CrO₄)₃·26H₂O at 25°C is −41.46±0.30. The temperature dependence of the log K_SP is log K_SP=A−B/T+D log(T) where A=498.94±48.99, B=27,499±2257, and D=−181.11±16.74. The values of ΔG⁰_r,298 and ΔH⁰_r,298 for the dissolution reaction are 236.6±3.9 and 77.5±2.4 kJ mol⁻¹. the values of ΔC⁰_P,r,298 and ΔS⁰_r,298 are −1506±140 and −534±83 J mol⁻¹ K⁻¹. Using these values and published standard state partial molal quantities for constituent ions, ΔG⁰_f,298=−15,131±19 kJ mol⁻¹, ΔH⁰_f,298=−17,330±8.6 kJ mol⁻¹, ΔS⁰₂₉₈=2.19±0.10 kJ mol⁻¹ K⁻¹, and ΔC⁰_Pf,298=2.12±0.53 kJ mol⁻¹ K⁻¹, were calculated.     

Mobility of Radiogenic Isotopes 4Не and 3Не and Their Retention in a Mineral (by the Example of Amphibole)

Doklady Earth Sciences -