Conceptual model of recharge to southeastern Badain Jaran Desert groundwater and lakes from environmental tracers

Sources of groundwater recharge to the Badain Jaran Desert in China have been investigated using geochemical and isotopic techniques. Stable isotope compositions (δ¹⁸O and δ²H) of shallow groundwater and surface water from oasis lakes evolve from a starting composition considerably depleted compared to local unsaturated zone moisture, confirming inferences from chloride mass balance that direct infiltration of precipitation is not a volumetrically important source of recharge to the shallow aquifer in the study area. Shallow phreatic and deeper confined groundwater bodies appear unconnected based on chemical composition and radiocarbon activities. Hydrogeologic evidence points toward a bordering mountain range (Yabulai) as a likely recharge zone, which is consistent with tracer results. A mean residence time in the range of 1–2 ka for the desert’s southeastern margin is inferred from radiocarbon. These results reveal that some replenishment to the desert aquifer is occurring but at a rate much lower than previously suggested, which is relevant for water resources planning in this ecologically sensitive area.     

Quantification of groundwater–surface water interactions using environmental isotopes: A case study of Bringi Watershed,Kashmir Himalayas,India

Environmental isotopes including \({\updelta }^{18}\)O, \({\updelta }^{2}\)H and \(^{3}\)H of precipitation, streams and springs were determined in the mountainous Bringi catchment of Kashmir Himalaya, dominated by carbonate lithology. The isotopic signature of winter precipitation is reflected in stream and spring water in late spring and is, therefore, representative of snow melting. The spring waters in September bear the enriched isotopic signatures of summer rainfall. The strong correlation (\(r^{2} = 0.97\)) between the isotopic composition of streams and springs indicates the streams and springs either share similar catchments or the springs are recharged by the streams. Chloride mass balance and isotopic mass balance studies suggest that the surface recharge component averages 337.35 m\(^{3}\)/s, which is about 75% of total stream discharge during the high flow period. Similarly, the contribution of surface water to groundwater recharge during the low flow period averages 7.5 m\(^{3}\)/s, which is about 18.6% of total stream flow. Furthermore, the mean residence time of the springs calculated from the tritium decay equation is very short (<1 year). The residence time is longer for Kongamnag and short for Achabalnag, which is further supported by dye testing.     

Geochemistry and stable isotopic composition of tufa waters and precipitates from the Interlake Region, Manitoba, Canada: Constraints on groundwater origin, calcitization, and tufa formation

New major, trace and isotopic geochemical results from a regional study of springs discharging from the major carbonate rock aquifer in the Interlake Region of Manitoba, Canada, are used to understand water–rock reactions, timing of recharge/discharge, tufa formation processes, and as baseline data. Spring waters are fresh with total dissolved solids (TDS) concentrations ranging from 150 to 880 mg/L. Waters discharging in the northern part of the study area have lower TDS, are dominantly Ca–Mg–HCO₃ waters with low SO₄ concentrations (<< 50 mg/L), and appear to have interacted primarily with Silurian carbonate lithologies. In contrast, waters in the southeastern part of the study area have higher TDS and have elevated SO₄ concentrations (up to 210 mg/L). Spring waters have elevated Mg/Ca_molar (1.23 ± 0.23), typically greater than congruent dissolution of dolomite. Ca and Mg concentrations and Mg/Ca_molar indicate that groundwater residence times were sufficient to allow equilibration with bedrock dolomite lithologies; elevated tritium in northern waters indicates a significant recharge component in the 1960's and 1970's. Tufa precipitates that have formed from many of the spring waters are low-Mg calcite (MgO = 1.70 to 5.80 wt.%). Sr concentrations are variable (57 to 657 ppm) and tufa Sr/Ca_molar ratios appear to be entirely controlled by spring water Sr/Ca_molar. Empirically determined Sr distribution coefficients (D_Sr = 0.389 ± 0.083) indicate rapid crystallization following CO₂ degassing, consistent with heavier δ¹³C_VPDB compared to spring waters. Sulfate concentrations are generally too low for calcitization (dedolomitization) reactions driven by anhydrite dissolution to be the dominant control on the elevated groundwater Mg/Ca_molar, implying either extensive sulfate reduction along the flow paths (however, δ¹³C_DIC suggests the elevated SO₄ is more consistent with Fe-sulfide oxidation), or that other processes are involved. Major ion ratios suggest that the waters in the southern part of the study area are more consistent with interaction with siliciclastic rocks than with anhydrite dissolution. We suggest that calcitization (dedolomitization) reactions driven by anhydrite dissolution may not dominate all carbonate aquifers and that mixing of waters in karst conduits combined with ion exchange reactions are important controls on water chemistry in these systems.     

Oxygen and hydrogen isotope geochemistry of thermal springs of the Western Cape, South Africa: Recharge at high altitude?

A number of thermal springs with temperature up to 64°C are found in the Western Cape Province of South Africa. The average δ¹³C value of gas (CO₂+CH₄) released at three springs is −22, which is consistent with an entirely biogenic origin for the C and supports previous investigations which showed that the springs are not associated with recent or nascent volcanic activity. Most springs issue from rocks of the Table Mountain Group, where faulted and highly jointed quartzites and sandstones of the Cape Fold Belt act as the main deep aquifer. The δD and δ¹⁸O values of the springs range from −46 to −18 and from −7.3 to −3.9, respectively. Although the thermal springs have isotope compositions that plot close to the local meteoric water line, their δD and δ¹⁸O values are significantly lower than ambient meteoric water or groundwater. It is, therefore, suggested that the recharge of most of the thermal springs is at a significantly higher altitude than the spring itself. The isotope ratios decrease wuth increasing distance from the west coast of South Africa, which is in part related to the continental effect. However, a negative correlation between the spring water temperature and the δ¹⁸O value in the thermal springs closest to the west coast indicates a progressive in increase in the average altitude of recharge away from the coast.     

Isotopic evidence for glacial meltwater recharge to the Cambrian-Ordovician aquifer, north-central United States

The chemistry of water in the Cambrian-Ordovician aquifer in six midwestern states has been studied as part of the Northern Midwest Regional Aquifer-System Analysis of the U.S. Geological Survey. Dissolved-solids concentrations generally increase perpendicular to the direction of regional groundwater flow, from less than 400 mg/liter in southeast Minnesota, southwest Wisconsin, and northeast Iowa to more than 10,000 mg/liter in northwest Missouri. Isotopic ratios of hydrogen and oxygen are significantly depleted from north to south, with an areal distribution approximately parallel to the distribution of dissolved solids. For example, δ¹⁸O in southern Iowa and northern Missouri is about 6 parts per thousand lighter than δ¹⁸O of modern recharge water in Minnesota and Wisconsin. Covariance between δ¹⁸O and δD of the groundwater, similar to that of modern precipitation, suggests that the differences in isotopic ratios between groundwater and modern recharge water reflect meteoric signatures of water during past recharge events rather than geochemical processes such as isotopic exchange with aquifer materials. The pronounced parallelism between the distribution of isotopes and dissolved solids over large areas probably reflects largescale recharge of Pleistocene glacial meltwater into the aquifer system, which probably had a paleoflow system with a gradient from northeast to southwest rather than from northwest to southeast.     

Groundwater recharge history and hydrogeochemical evolution in the Minqin Basin, North West China

The Minqin Basin is a type area for examining stress on groundwater resources in the Gobi Desert, and has been investigated here using a combination of isotopic, noble gas and chemical indicators. The basin is composed of clastic sediments of widely differing grain size and during the past half century over 10 000 boreholes have been drilled with a groundwater decline of around 1 m a⁻¹. Modern diffuse recharge is unlikely to exceed 3 mm a⁻¹, as determined using unsaturated zone profiles and Cl⁻ mass balance. A small component of modern (<50 a) groundwater is identified in parts of the basin from ³H–³He data, probably from irrigation returns. A clear distinction is found between modern waters with median δ¹⁸O values of 6.5 ± 0.5‰ and most groundwaters in the basin with more depleted isotopic signatures. Radiocarbon values as pmc range from 0.6% to 85% modern, but it is difficult to assign absolute ages to these, although a value of 20% modern C probably represents the late Pleistocene to Holocene transition. The δ¹³C compositions remain near-constant throughout the basin (median value of −8.1‰ δ¹³C) and indicate that carbonate reactions are unimportant and also that little reaction takes place. There is a smooth decrease in ¹⁴C activity accompanied by a parallel increase in ⁴He accumulations from S–N across the basin, which define the occurrence of a regional flow system. Noble gas temperatures indicate recharge temperatures of about 5.6 °C for late Pleistocene samples, which is some 2–3 °C cooler than the modern mean annual air temperature and the recharge temperature obtained from several Holocene samples. Groundwaters in the Minqin Basin have salinities generally below 1 g/L and are aerobic, containing low Fe but elevated concentrations of U, Cr and Se (mean values of 27.5, 5.8 and 5.3 μg L⁻¹, respectively). Nitrate is present at baseline concentrations of around 2 mg L⁻¹ but there is little evidence of impact of high NO₃ from irrigation returns. Strontium isotope and major ion ratios suggest that silicate reactions predominate in the aquifer. The results have important implications for groundwater management in the Minqin and other water-stressed basins in NW China – a region so far destined for rapid development. The large proportion of the water being used at present is in effect being mined and significant changes are urgently needed in water use strategy.     

Assessing the past thermal and chemical history of fluids in crystalline rock by combining fluid inclusion and isotopic investigations of fracture calcite

Fluid inclusion studies combined with the isotope geochemistry of several generations of fracture calcite from the Olkiluoto research site, Finland, has been used to better understand the past thermal and fluid history in the crystalline rock environment. Typically, fracture mineral investigations use O and C isotopes from calcite and an estimate of the isotopic composition of the water that precipitated the calcite to perform δ¹⁸O geothermometry calculations to estimate past temperature conditions. By combining fluid inclusion information with calcite isotopes, one can directly measure the temperature at which the calcite formed and can better determine past fluid compositions. Isotopic, petrologic and fluid inclusion studies at the Olkiluoto research site in Finland were undertaken as part of an investigation within the Finnish nuclear waste disposal program. The study revealed that four fluids were recorded by fracture calcites. From petrologic evidence, the first fluid precipitated crystalline calcite at 151–225°C with a δ¹³C signature of −21 to −13.9‰ PDB and a δ¹⁸O signature of 12.3–13.0‰ SMOW. These closed fracture fillings were found at depths greater than 500 m and were formed from a high temperature, low salinity, Na–Cl fluid of possible meteoric water altered by exchange with wallrock or dilute basinal origin. The next fluid precipitated crystalline calcite with clay at 92–210°C with a δ¹³C signature of −2.6 to +3.8‰ PDB and a δ¹⁸O signature of 19.4–20.7‰ SMOW. These closed fracture fillings were found at depths less than 500 m and were formed from a moderate to high temperature, low to moderate salinity, Na–Cl fluid, likely of magmatic origin. The last group of calcites to form, record the presence of two distinct fluid types. The platy (a) calcite formed at 95–238°C with a δ¹³C signature of −12.2 to −3.8‰ PDB and a δ¹⁸O signature of 14.9–19.6‰ SMOW, from a high temperature, low salinity, Na–Cl fluid of possible magmatic origin. The platy (b) calcite formed at 67–98°C with a δ¹³C signature of −13.0 to −6.2‰ PDB and a δ¹⁸O signature of 15.1–20.1‰ SMOW, from a low temperature, high salinity, Ca–Na–Cl fluid of possible basinal brine origin. The two calcites are related through a mixing between the two end members. The source of the fluids for the platy grey (a) calcites could be the olivine diabase dykes and sills that cut through the site. The source of fluids for the platy (b) calcites could be the Jotnian arkosic sandstone formations in the northern part of the site. At the Olkiluoto site, δ¹⁸O geothermometry does not agree with fluid inclusion data. The original source of the water that forms the calcite has the largest effect on the isotopic signature of the calcites formed. Large isotopic shifts are seen in any water by mineral precipitation during cooling under rock–water equilibrium fractionation conditions. Different calcite isotopic signatures are produced depending on whether cooling occurred in an open or closed system. Water–rock interaction, at varying W/R ratios, between a water and a host rock can explain the isotopic shifts in many of the calcites observed. In some cases it is possible to shift the δ¹⁸O of the water by +11.5‰ (SMOW) using a realistic water–rock ratio. This process still does not explain some of the very positive δ¹⁸O values calculated using fluid inclusion data. Several other processes, such as low temperature recrystallization, boiling, kinetic effects and dissolution of calcite from fluid inclusion walls can affect isotopic signatures to varying degrees. The discrepancy between fluid inclusion data and δ¹⁸O geothermometry at the Olkiluoto site was most likely due to poor constraint on the original source of the water.     

Hydrology of a spring complex, studied by geochemical time-series data, Acquarossa, Switzerland

A case study of three springs in Switzerland is used to demonstrate the value of geochemical time-series data as a powerful tool to study the dynamics of groundwater systems. Values of repeatedly measured parameters revealed intermixings of two water types: (a) a 29°C water, circulating to a depth of 1100 m and containing approximately 700 mg/l Ca, 2000 mg/l SO₄, 700 mg/l HCO₃, 20 mg/l of Na and Cl, 6 mg/l Fe, at least 47 mg/l SiO₂, and with an isotopic composition of δD = − 73.0‰ and δ¹⁸ O = −10.9‰, and (b) a 12°C or colder water, shallow, and of a post-1953 age, containing 420 mg/l TDI or less, very low in Na and Cl (4 mg/l or less), isotopic values of δD = −71.0‰ and δ¹⁸ O = −10.5‰ and tritium as in recent (post-bomb) precipitation.     

Geochemical and isotopic characterization of groundwater from shallow and deep limestone aquifers system of Aleppo basin (north Syria)

Stable isotopes (δ¹⁸O, δ²H and ¹³C) and radioactivity (³H, ¹⁴C) have been used in conjunction with chemical data to evaluate the processes generating the chemical composition, reconstruct the origin of the water and groundwater residence time. The Aleppo basin is comprised of two main limestone aquifers: the first one is unconfined of Paleogene age and the second is confined of Upper Cretaceous age. The chemical data indicate that the dissolution of minerals and evaporation are the main processes controlling groundwater mineralization. The groundwater from the two aquifers is characterized by distinctive stable isotope signatures. This difference in water isotopes is interpreted in terms of difference origin and recharge period. Fresh and brackish shallow groundwater were mostly recharged during the Holocene period. The presence of ³H in several groundwater samples of this aquifer gives evidence that groundwater recharge is going on. Brackish water of the deep confined aquifer has depleted stable isotope composition and very low ¹⁴C activity that indicates recharge during the late Pleistocene cold period.     

Chemistry and sulfur isotopic composition of precipitation at Bologna, Italy

Individual and monthly precipitation samples from the polluted atmosphere of Bologna (Emilia-Romagna province) were collected during March 1996 to May 1997 and analyzed for major ions in solution and S isotopes in dissolved SO₄.Weighted mean enrichment factors relative to seawater are found to be 1.0 for Na, 15.2 for K, 105 for Ca, 3.3 for Mg, 17.3 for SO₄ and 663 for HCO⁻₃. Very good positive correlations are observed for the Ca²⁺–Mg²⁺–HCO⁻₃–SO²⁻₄–NO⁻₃ system, indicating that dissolution of Ca (±Mg)-carbonate particles by H₂SO₄ and HNO₃ from combustion of oil and gas is a major process controlling the chemical composition of rain and snow. Na⁺ and Cl⁻ in monthly precipitation derive essentially from sea spray, but the contribution of Na⁺ from continental sources is appreciable in a number of individual rains. NH⁺₄ appears to be on average more abundant in spring and summer precipitation, its main sources being microbial activity in soils and application of fertilizers. K⁺ is probably of continental origin from soil dust.The S isotopic composition of SO₄ is systematically positive, with mean δ³⁴S values of +3.2±1.6‰ (n=40) in individual precipitation and +2.8±1.4‰ (n=12) in monthly precipitation. These isotopic compositions are interpreted in terms of a dominant contribution of S from anthropogenic emissions and subordinate contributions from biogenic and marine sources. Pollutant SO₄ is estimated to have a δ³⁴S value in the range +2.5 to +4.5‰, whereas a distinctive δ³⁴S of −4.5‰ or lower indicates SO₄ from oxidation of biogenic gases.The isotopic and chemical compositions of SO₄ do not depend on wind direction, thus testifying to a mostly local source for pollutant S in the Bologna atmosphere.     

Oxygen isotope composition of annually banded modern and mid-Holocene travertine and evidence of paleomonsoon floods, Grand Canyon, Arizona, USA

Holocene and modern travertine formed in spring-fed Havasu Creek of the Grand Canyon, Arizona, was studied to determine the factors governing its oxygen-isotope composition. Analysis of substrate-grown travertine indicates that calculated calcite-formation temperatures compare favorably with measured water temperatures, and include silt-rich laminae deposited by monsoon-driven floods. Ancient spring-pool travertine is dated by U-series at 7380 ± 110 yr and consists of 14 travertine-silt couplets of probable annual deposition. One hundred eighty high-resolution δ¹⁸O analyses of this mid-Holocene sample average −11.0‰ PDB. The average value for modern travertine is 0.5‰ lower, perhaps because mid-Holocene temperature was higher or there was proportionally greater summer recharge. δ¹⁸O cyclicity in the mid-Holocene travertine has average amplitude of 1.9 ± 0.5‰ PDB, slightly less than the inferred modern-day annual temperature range of Havasu Creek. The annual temperature range might have been reduced during the 14-yr interval compared to present, although other non-temperature factors could account for the muted annual variation. Silt-rich laminae within isotopically lower calcite in the modern and mid-Holocene travertine verifies the seasonal resolution of both samples, and suggests that similar temperature-precipitation conditions, as well as monsoon-generated summer floods, prevailed in the mid-Holocene as they do throughout the Grand Canyon region today.     

Stable isotope evidence for multiple fluid regimes during carbonate cementation of the Upper Tertiary Hazeva Formation, Dead Sea Graben, southern Israel

Stable carbon- and oxygen-isotope compositions of calcite and dolomite cements have been used to understand porewater evolution in the Upper Tertiary Hazeva Formation within the Dead Sea Graben, southern Israel. Sandstone samples were obtained from four boreholes in three tectonic blocks of the graben over depths of 253–6448 m, a variation that largely reflects differential subsidence of individual fault-bounded blocks. Early carbonate cements dominate diagenesis. Calcite occurs at <1600 m, but was replaced by dolomite at greater depths. Dolomite at 1600–2700 m is Fe-poor (<0.8 mol% FeCO₃), and at 4700–6200 m, Fe-rich (0.5–7.2 mol% FeCO₃). Magnesite, anhydrite and halite are the final diagenetic phases. Calcite has positively correlated δ¹⁸O (+21‰ to +25‰) and δ¹³C (−6‰ to −2‰) values that generally decrease with depth. Dolomite has a wider variation in δ¹⁸O (+18‰ to +30‰) and δ¹³C (−8‰ to −1‰) values, which also generally are lower with increasing depth. However, the δ¹³C and δ¹⁸O values of dolomite from the uppermost 400 m of the Hazeva Formation in the Sedom Deep-1 borehole are anomalous in spanning the entire range of stable carbon and oxygen isotopic compositions over this relatively small interval.The decreasing dolomite δ¹³C values likely indicate an increased contribution of carbon from organic sources with increasing depth. Except for the uppermost 400 m, Hazeva Formation dolomite in the Sedom Deep-1 borehole has stable carbon-isotope compositions that imply initial dolomitization at much shallower levels, prior to the preferential subsidence of this tectonic block. The oxygen isotopic compositions of the calcite cement are best explained by equilibration at present burial temperatures (≤55 °C) with porewater of meteoric origin. Its δ¹⁸O values increased from −5‰ at the shallowest depths to 0‰ at 1600 m. The dolomite oxygen isotopic compositions also reflect equilibration at present burial temperatures with porewaters ranging from 0‰ at 1600 m to +7‰ at 3600 m (100 °C). In the deepest fault block (Sedom Deep-1 borehole), however, increasingly Fe-rich dolomite has (re)equilibrated with porewater whose δ¹⁸O values decreased from +9‰ at 4750 m (120 °C) to +1‰ to +2‰ by 6200 m (150 °C).Much of the dolomite likely formed at relatively shallow depths from saline brines derived from precursors to the Dead Sea. These infiltrated the Hazeva Formation, mixing with and largely displacing meteoric water, and dolomitizing calcite. Rock–water ratios tended to be high during these processes. However, the upper 400 m of the Hazeva Formation in the deepest fault block were likely deposited during its rapid tectonic subsidence, and largely escaped the initial style of dolomitization pervasive elsewhere in the study area. These sediments were also capped by evaporites. This relatively thin interval likely became a preferential conduit for brines that escaped underlying and overlying strata, including the Fe-rich, lower ¹⁸O fluids (evolved seawater?) present in the deepest part of the graben. These rocks present the most promising target for the passage and accumulation of hydrocarbons in the study area.     

Sandstone diagenesis in the Pattani Basin (Gulf of Thailand): history of water-rock interaction and comparison with the Gulf of Mexico

In the Pattani Basin, a failed-rift basin, extensive water-rock interaction has occurred between subquartzose alluvial sandstones of Miocene age and their pore fluids. Diagenetic rates and pathways have been strongly influenced by high geothermal gradients, high CO₂ fugacities, and low pore water salinities. Depositional pore water was fresh to brackish, depending on the depositional environment of the sediments. Chloride concentrations in modern formation water are believed primarily to reflect the proportions of river and sea water in the depositional environment. However, the concentration of other important solutes and the isotopic composition of the formation waters can not be explained by roportional mixing of these two end-member waters. Dissolution of detrital plagioclase (An = 3) and K- feldspar are reactions of major significance that are reflected chemically in the Na/Cl and K/Cl ratios of the formation water. Despite the high temperature of the sandstones (120–200°C), diagenetic albite does not occur. Geochemical calculations indicate the formation water is undersaturated with respect to both orthoclase and albite. This style of feldspar diagenesis differs significantly from that of sandstones of similar composition in other basins, and has probably influenced other aspects of silicate diagenesis.Important authigenic minerals are: 1. locally abundant calcite cement (δ¹³C= −12.8, δ¹⁸O= −17.3 PDB), an early diagenetic phase that formed at about 60°C; 2. pore-filling kaolinite (δ¹⁸O= 9.9, δD= −83.5SMOW) that was closely associated with feldspar dissolution and formed over a range of temperatures; and 3. fibrous pore-lining and pore-bridging illite (δ¹⁸O = 9.8, δD = − 86.7 SMOW, the last significant cement, formed at temperatures of 120 to 150°C. Potassium/argon dates on illite indicate that sandstone diagenesis took place during a period of rapid sedimentation in the first two-thirds of the burial history.Comparison of Pattani Basin diagenesis with diagenesis of sandstones of similar age in other sedimentary basins demonstrates that chemical diagenesis, relative to mechanical compaction, has been especially rapid in the Pattani Basin. This reflects the effect of high temperatures on reaction rates. The net effect is a high average rate of porosity loss with burial (11% km).     

Characterizing groundwater recharge using oxygen and hydrogen isotopes: a case study in a temperate forested region,South Korea

In the cool temperate region of South Korea, oxygen and hydrogen isotopes of groundwater, lake water, and precipitation were studied to determine the season of groundwater recharge. All the groundwater samples, irrespective of season, on δ¹⁸O–δ²H scale plotted along the summer precipitation, suggesting summer precipitation largely modulates recharge. The deuterium excess values of groundwater (d-excess) show clear seasonal difference, higher in winter (> 18‰) and lower in summer (< 10‰). And its resemblance to the summer precipitation d-excess value further suggests dominant role of summer precipitation in groundwater recharge. Based on the mass balance equation, with end-member d-excess values of seasonal precipitation and groundwater as input variables, groundwater is composed of 66% summer and 34% winter precipitation. Despite the study area being heavily forested, summer rainfall contribution higher than winter suggests that evapotranspiration effect is minimal in the region; may be due to thin sand–gravel-based porous soil overlying highly weathered granitic rock system.     

Hydrogeochemical and isotopic evidence of groundwater evolution and recharge in aquifers in Beijing Plain, China

An investigation was conducted in Beijing to identify the groundwater evolution and recharge in the quaternary aquifers. Water samples were collected from precipitation, rivers, wells, and springs for hydrochemical and isotopic measurements. The recharge and the origin of groundwater and its residence time were further studied. The groundwater in the upper aquifer is characterized by Ca-Mg-HCO₃ type in the upstream area and Na-HCO₃ type in the downstream area of the groundwater flow field. The groundwater in the lower aquifer is mainly characterized by Ca-Mg-HCO₃ type in the upstream area and Ca-Na-Mg-HCO₃ and Na-Ca-Mg-HCO₃ type in the downstream area. The δD and δ¹⁸O in precipitation are linearly correlated, which is similar to WMWL. The δD and δ¹⁸O values of river, well and spring water are within the same ranges as those found in the alluvial fan zone, and lay slightly above or below LMWL. The δD and δ¹⁸O values have a decreasing trend generally following the precipitation → surface water → shallow groundwater → spring water → deep groundwater direction. There is evidence of enrichment of heavy isotopes in groundwater due to evaporation. Tritium values of unconfined groundwater give evidence for ongoing recharge in modern times with mean residence times <50 a. It shows a clear renewal evolution along the groundwater flow paths and represents modern recharge locally from precipitation and surface water to the shallow aquifers (<150 m). In contrast, according to ¹⁴C ages in the confined aquifers and residence time of groundwater flow lines, the deep groundwater is approximately or older than 10 ka, and was recharged during a period when the climate was wetter and colder mainly from the piedmont surrounding the plain. The groundwater exploitation is considered to be “mined unsustainably” because more water is withdrawn than it is replenished.     

Simulated diagenesis and catagenesis of marine kerogen precursors: Melanoidins as model systems for light hydrocarbon generation

Amino acids and sugars are principal constituents of marine organisms. The condensation of amino acids and sugars is one possible nonenzymatic, early diagenetic pathway for the incorporation of these compounds into more complex geopolymers. In this study, aqueous solutions consisting of l-lysine, l-histidine, l-arginine and d-(+)-glucose were heated (100°C) for up to 288 h. Portions of the melanoidin polymer isolated after heating were reheated in the presence of water (hydrous pyrolysis) for 72 h at 325°C. Reaction products were identified by GC and GC/MS. Stable isotopic (δ¹³C) and elemental analyses were used to follow thermal evolution.While the initial melanoidin was synthesized from a simple, four component system, the products generated during hydrous pyrolysis are of considerable complexity, and include straightchain and branched alkanes, alkadienes, alkynes, indole, dimethyl indane, ethyl phenol, quinoline, and xylenes, in addition to a multitude of as yet, unidentified components. Stable carbon isotopic values for the reactants and products correspond to trends observed for naturally generated geopolymers and light gases. Elemental analyses of the melanoidin prior and subsequent to hydrous pyrolysis indicate a kerogen evolution pathway similar to that observed for natural samples. Considering the intractable nature of kerogen, laboratory simulation studies of simple systems can provide an alternative approach for elucidating the origins of geopolymers and their potential for hydrocarbon generation.     

Initial assessment of recharge areas for large karst springs: a case study from the central Zagros Mountains,Iran

Sousan Spring emerges from the Keyno Anticline, Zagros Mountains (Iran), and the mean annual discharge is ~24 m³/s. Geological and hydrochemical evaluations suggest that the spring recharge is from the limestone Ilam-Sarvak Formation (Cretaceous) but the Mafaroon Fault, a major thrust feature, influences the regional groundwater flow path by juxtaposing other strata. Geological, geochemical, stable isotope and water balance studies were employed to interpret this behavior. Using the isotope data, the sources and elevations of the recharge area were found. Temporal variations of the isotopic data were compared with variations of electrical conductivity (EC). Unexpectedly, high EC was associated with a relative increase of discharge and depletion of δ¹⁸O. Several hypotheses were investigated and approximate water balance studies employed for validation. It was found that an elongated catchment on the Keyno Anticline plus a lesser catchment on a pair of parallel anticlines recharge the aquifer. While the long groundwater flow path along the Keyno Anticline plus guidance by Mafaroon Fault and the adjacent Garou shaly strata lead to increased EC in the Sousan Spring at the end of the dry season, a flow pulse from two adjoining anticlines (Mahalbakh and Shirgoon) arrives at the same time to increase the discharge and deplete the δ¹⁸O signal. Apparently the spring did not experience true base flow conditions during the recorded hydrological year. Although the spring response to specific precipitation events was similar to typical karst aquifers, standard interpretation of recession curves and related coefficients will not be practical at Sousan.     

A multi-tracer approach to delineate groundwater dynamics in the Rio Actopan Basin,Veracruz State,Mexico

Geochemistry and environmental tracers were used to understand groundwater resources, recharge processes, and potential sources of contamination in the Rio Actopan Basin, Veracruz State, Mexico. Total dissolved solids are lower in wells and springs located in the basin uplands compared with those closer to the coast, likely associated with rock/water interaction. Geochemical results also indicate some saltwater intrusion near the coast and increased nitrate near urban centers. Stable isotopes show that precipitation is the source of recharge to the groundwater system. Interestingly, some high-elevation springs are more isotopically enriched than average annual precipitation at higher elevations, indicating preferential recharge during the drier but cooler winter months when evapotranspiration is reduced. In contrast, groundwater below 1,200 m elevation is more isotopically depleted than average precipitation, indicating recharge occurring at much higher elevation than the sampling site. Relatively cool recharge temperatures, derived from noble gas measurements at four sites (11–20 °C), also suggest higher elevation recharge. Environmental tracers indicate that groundwater residence time in the basin ranges from 12,000 years to modern. While this large range shows varying groundwater flowpaths and travel times, ages using different tracer methods (¹⁴C, ³H/³He, CFCs) were generally consistent. Comparing multiple tracers such as CFC-12 with CFC-113 indicates piston-flow to some discharge points, yet binary mixing of young and older groundwater at other points. In summary, groundwater within the Rio Actopan Basin watershed is relatively young (Holocene) and the majority of recharge occurs in the basin uplands and moves towards the coast.     

拉萨河流域地表径流氢氧同位素空间分布特征

为了探析径流过程中稳定同位素变化特征及其控制因子, 利用2008年拉萨河流域地表径流中δ18O和δD的监测数据以及相关气象和水文资料, 初步研究了流域δ18O和δD的空间分布特征.研究发现: (1)拉萨河流域以大气降水为主要补给来源, 且干流体现了较明显的蒸发效应; (2)河水偏正的d过量参数特征指示了冰雪融水的补给特征; (3)季风降水期间, 拉萨河流域由高程效应和水平距离所造成的δ18O递减率约为0.16‰·(100 m)-1; (4)大循环尺度下, 流域内河水呈现了明显的大陆效应.研究表明高海拔地区地表径流氧氘同位素分布特征能够有效示踪流域水文循环过程, 并提供古高度变化研究的稳定同位素证据.      

Fluid geochemistry in the Ivigtut cryolite deposit, South Greenland

The 1.27 Ga old Ivigtut (Ivittuut) intrusion in South Greenland is world-famous for its hydrothermal cryolite deposit [Na₃AlF₆] situated within a strongly metasomatised A-type granite stock. This detailed fluid inclusion study characterises the fluid present during the formation of the cryolite deposit and thermodynamic modelling allows to constrain its formation conditions.Microthermometry revealed three different types of inclusions: (1) pure CO₂, (2) aqueous-carbonic and (3) saline-aqueous inclusions. Melting temperatures range between − 23 and − 15 °C for type 2 and from − 15 to − 10 °C for type 3 inclusions. Most inclusions homogenise between 110 and 150 °C into the liquid.Stable isotope compositions of CO₂ and H₂O were measured from crushed inclusions in quartz, cryolite, fluorite and siderite. The δ¹³C values of about − 5‰ PDB are typical of mantle-derived magmas. The differences between δ¹⁸O of CO₂ (+ 21 to + 42‰ VSMOW) and δ¹⁸O of H₂O (− 1 to − 21.7‰ VSMOW) suggest low-temperature isotope exchange. δD (H₂O) ranges from − 19 to − 144‰ VSMOW. The isotopic composition of inclusion water closely follows the meteoric water line and is comparable to Canadian Shield brines. Ion chromatography revealed the fluid's predominance in Na, Cl and F. Cl/Br ratios range between 56 and 110 and may imply intensive fluid–rock interaction with the host granite.Isochores deduced from microthermometry in conjunction with estimates for the solidification of the Ivigtut granite suggest a formation pressure of approximately 1–1.5 kbar for the fluid inclusions. Formation temperatures of different types of fluid inclusions vary between 100 and 400 °C. Thermodynamic modelling of phase assemblages and the extraordinary high concentration in F (and Na) may indicate that the cryolite body and its associated fluid inclusions could have formed during the continuous transition from a volatile-rich melt to a solute-rich fluid.