Development of an incised valley‐fill at an evolving rift margin: Pleistocene eustasy and tectonics on the southern side of the Gulf of Corinth,Greece

This study from the southern margin of the Gulf of Corinth documents a Late Pleistocene incised valley‐fill succession that differs from the existing facies models, because it comprises gravelly shoal‐water and Gilbert‐type deltaic deposits, shows strong wave influence and lacks evidence of tidal activity. The valley‐fill is at least 140 m thick, formed in 50 to 100 ka between the interglacials Marine Isotope Stage 9a and Marine Isotope Stage 7c. The relative sea‐level rise left its record both inside and outside the incised valley, and the age of the valley‐fill is estimated from a U/Th date of coral‐bearing deposits directly outside the palaeovalley outlet. Tectonic up‐warping due to formation of a valley‐parallel structural relay ramp contributed to the valley segmentation and limited the landward extent of marine invasions. The valley segment upstream of the ramp crest was filled with a gravelly alluvium, whereas the downstream segment accumulated fluvio‐deltaic deposits. The consecutive deltaic systems nucleated in the ramp‐crest zone, forming a bathymetric gradient that promoted the ultimate growth of thick Gilbert‐type delta. The case study contributes to the spectrum of conceptual models for incised valley‐fill architecture. Four key models are discussed with reference to the rates of sediment supply and accommodation development, and it is pointed out that not only similarity, but also all departures of particular field cases from these end‐member models may provide valuable information on the system formative conditions. The Akrata incised valley‐fill represents conditions of high sediment supply and a rapid, but stepwise development of accommodation that resulted from the spatiotemporal evolution of normal faulting at the rift margin and overprinted glacioeustatic signals. This study adds to an understanding of valley‐fill architecture and provides new insights into the Pleistocene tectonics and palaeogeography of the Corinth Rift margin.     

Stratigraphic architecture and infill history of a deglaciated bedrock valley based on georadar, seismic profiling and drilling

The sediment fill of a silled bedrock valley in Western Norway has been investigated with respect to stratigraphy and infill history using a combination of mapping, georadar, seismic profiling and drilling. A small outlet glacier occupies the head of the valley that displays a stepwise down-valley profile and terminates in a lake at 29 m above sea-level. The valley is surrounded by high, steep bedrock slopes and is characterized by a series of filled basins each limited by sills of bedrock or moraine accumulations. Till, glacial outwash and/or rockslide deposits fill in the lower half of the two larger basins. (Fan) delta deposits fringed by the deposits of alluvial fans and colluvial cones dominate the upper fill of most basins. (Fan) delta deposits interfinger downstream with lake sediments in the larger basins and fluvial deposits comprise the top fill. The overall infill pattern was controlled by deglaciation as well as basin size and shape. An overall decreasing sediment supply following deglaciation is shown in the fill of a larger basin down-valley, whereas a recently increasing sediment supply during glacier growth is reflected primarily in an upstream basin. Only the lowermost basin was exposed to a sea-level drop from 75 m above sea-level to the present lake level associated with incision and river migration. This observation is in contrast to the basins above marine influence where incision has been limited due to fixed downstream sills resulting in insignificant erosion except for some fan-head entrenchment. It follows that the fills of these small valley basins display progradational and aggradational trends of deposition and paraglacial reworking has been limited. Additionally, the study demonstrates that georadar profiling, combined with other methods, is very useful for comprehensive investigation of valley basins.     

Architecture and evolution of a fjord‐head delta,western Vancouver Island,British Columbia

The architectural framework and Holocene evolution of the Zeballos fjord‐head delta on west‐central Vancouver Island was established through a multidisciplinary field‐based study. The Zeballos delta is a composite feature, consisting of an elevated, incised, late Pleistocene delta and an inset Holocene delta graded to present sea level. Both deltas have a classic Gilbert‐type tripartite architecture, with nearly flat topset and bottomset units and an inclined foreset unit. Time domain electromagnetic (TDEM) and ground‐penetrating radar (GPR) surveys, borehole data, and gravel pit exposures provided information on the internal form, lithologies and substrate of both deltas. Both sets of deltaic deposits coarsen upward from silt in the bottomset unit to gravel in the topset unit. The TDEM survey revealed a highly irregular, buried bedrock surface, ranging from 20 m to 190 m in depth, and it delineated saltwater intrusion into the deltaic sediments. Late Quaternary sea‐level change at Zeballos was inferred from delta morphology and the GPR survey. The elevated, late Pleistocene delta was constructed when the sea was about 21 m higher relative to the land than it is today. It was dissected when sea‐level fell rapidly as a result of glacio‐isostatic rebound. Relative sea‐level reached a position about 20 m below the present datum during the early Holocene. Foreset beds that overlap and progressively climb in a seaward direction and topset beds that thicken to 26 m landward imply that the delta aggraded and prograded into Zeballos Inlet during the middle and late Holocene transgression. Sea‐level may have risen above the present datum during the middle Holocene, creating a delta plain at about 4 m a.s.l. Remnants of this surface are preserved along the valley margins. Copyright © 2004 John Wiley & Sons, Ltd.     

Alluvial architecture of the Holocene Rhine–Meuse delta (the Netherlands)

Ancient fluvial successions often act as hydrocarbon reservoirs. Sub‐surface data on the alluvial architecture of fluvial successions are often incomplete and modelling is performed to reconstruct the stratigraphy. However, all alluvial architecture models suffer from the scarcity of field data to test and calibrate them. The purposes of this study were to quantify the alluvial architecture of the Holocene Rhine–Meuse delta (the Netherlands) and to determine spatio‐temporal trends in the architecture. Five north–south orientated cross‐sections, perpendicular to the general flow direction, were compiled for the fluvial‐dominated part of the delta. These sections were used to calculate the width/thickness ratios of fluvial sandbodies (SBW/SBT) and the proportions of channel‐belt deposits (CDP), clastic overbank deposits (ODP) and organic material (OP) in the succession. Furthermore, the connectedness ratio (CR) between channel belts was calculated for each cross‐section. Distinct spatial and temporal trends in the alluvial architecture were found. SBW/SBT ratios decrease by a factor of ca 4 in a downstream direction. CDP decreases from ca 0·7 (upstream) to ca 0·3 (downstream). OP increases from less than 0·05 in the upstream part of the delta to more than 0·25 in the downstream delta. ODP is approximately constant (0·4). CR is ca 0·25 upstream, which is approximately two times larger than in the downstream part of the delta. Furthermore, CDP in the downstream Rhine–Meuse delta increases after 3000 cal yr BP. These trends are attributed to variations in available accommodation space, floodplain geometry and channel‐belt size. For instance, channel belts tend to narrow in a downstream direction, which reduces SBW/SBT, CDP and CR. Tectonics cause local deviations in the general architectural trends. In addition, the positive correlation between avulsion frequency and the ratio of local to regional aggradation rate probably influenced alluvial architecture in the Rhine–Meuse delta. The Rhine–Meuse data set can be a great resource when developing more sophisticated models for alluvial architecture simulation, which eventually could lead to better characterizations of hydrocarbon reservoirs. To aid such usage of the Rhine–Meuse data set, constraints for relevant parameters are provided at the end of the paper.     

Stratigraphic architecture of a tide‐influenced shelf‐edge delta,Upper Cretaceous Dorotea Formation,Magallanes‐Austral Basin,Patagonia

The Magallanes‐Austral Basin of Patagonian Chile and Argentina is a retroforeland basin associated with Late Cretaceous–Neogene uplift of the southern Andes. The Upper Cretaceous Dorotea Formation records the final phase of deposition in the Late Cretaceous foredeep, marked by southward progradation of a shelf‐edge delta and slope. In the Ultima Esperanza district of Chile, laterally extensive, depositional dip‐oriented exposures of the Dorotea Formation contain upper slope, delta‐front and delta plain facies. Marginal and shallow marine deposits include abundant indicators of tidal activity including inclined heterolithic stratification, heterolithic to sandy tidal bundles, bidirectional palaeocurrent indicators, flaser/wavy/lenticular bedding, heterolithic tidal flat deposits and a relatively low‐diversity Skolithos ichnofacies assemblage in delta plain facies. This work documents the stratigraphic architecture and evolution of the shelf‐edge delta that was significantly influenced by strong tidal activity. Sediment was delivered to a large slump scar on the shelf‐edge by a basin‐axial fluvial system, where it was significantly reworked and redistributed by tides. A network of tidally modified mouth bars and tidal channels comprised the outermost reaches of the delta complex, which constituted the staging area and initiation point for gravity flows that dominated the slope and deeper basin. The extent of tidal influence on the Dorotea delta also has important implications for Magallanes‐Austral Basin palaeogeography. Prior studies establish axial foreland palaeodrainage, long‐term southward palaeotransport directions and large‐scale topographic confinement within the foredeep throughout Late Cretaceous time. Abundant tidal features in Dorotea Formation strata further suggest that the Magallanes‐Austral Basin was significantly embayed. This ‘Magallanes embayment’ was formed by an impinging fold–thrust belt to the west and a broad forebulge region to the east.     

全新世长江三角洲的发育及其对相邻海岸沉积体系的影响

依据钻孔资料和已发表的文献,对全新世长江三角洲的形成和发育及其对相邻沉积体系的影响作了综合和概括.在末次冰期低海平面时,现今长江三角洲地区可分为下切河谷和两侧的河间地两个古地貌单元.冰后期海平面上升,下切河谷被淹,并转化为河口湾,海水随之扩展到两侧的古河间地.全新世最大海侵时形成以镇江-扬州为顶点的古河口湾.7000～7500年以来,当沉积速率超过海平面上升速度时,长江带来的物质大量沉积,河口湾被充填,并逐渐转变为潮汐平原和三角洲.河口湾被充填之后,长江带来的河流泥沙随之溢出河口湾,进入相邻的河口海岸地区,影响相邻沉积体系的形成和发育.长江泥沙向南进入钱塘江河口湾,在湾顶形成沙坎;向北输运,成为苏北南黄海潮成沙脊的重要物源,影响该潮成体系的形成和发展.舟山群岛海蚀平台上直接覆盖泥质沉积是以退积为主的河口湾向进积的三角洲环境转变的又一证据.长江输沙量在不断减少,而河口滩涂围垦力度在增加,这将导致相邻的河口海岸沉积体系增长速度减缓,出现侵蚀或侵蚀加剧.     

Late Quaternary depositional history of the Reuss delta,Switzerland: constraints from high‐resolution seismic reflection and georadar surveys

Glacial erosion has caused overdeepening of many alpine valleys. After retreat of the ice, they were filled with heterogeneous deposits of glacial, lacustrine and fluvial sediments. A typical example of such a valley segment and its infill is the Reuss delta on the southern shore of Lake Lucerne in Switzerland. To obtain a detailed three‐dimensional image of this valley segment, the ETH Institute of Geophysics has acquired several two‐dimensional, high‐resolution seismic and georadar profiles, and conducted a three‐dimensional georadar survey. Interpretations of these geophysical data were constrained by a geological core extracted from a borehole 300 m deep near the investigation site. The seismic profiles imaged ca. 600 m of sediment infill above bedrock. Based on their reflection characteristics, five different deposition units were distinguished. These units were interpreted as a succession of clay/silt at the base, followed by different sand units with variable but generally increasing amounts of gravel. This succession represented a prograding delta that filled the southern part of Lake Lucerne. The latest fluvial development of the region is best represented by the georadar data. In particular, the three‐dimensional georadar data set provides a detailed view of an ancient braided river channel Copyright © 2002 John Wiley & Sons, Ltd.     

Architecture and sedimentology of the Kerinitis Gilbert‐type fan delta,Corinth Rift,Greece

The Kerinitis Delta in the Corinth Rift, Greece, is a footwall derived, coarse‐grained, Gilbert‐type fan delta deposited in the hangingwall of a linked normal fault system. This giant Gilbert‐type delta (radius 3·8 km, thickness > 600 m) was supplied by an antecedent river and built into a brackish to marine basin. Although as yet poorly dated, correlation with neighbouring deltas suggests that the Kerinitis Delta was deposited during a period of 500 to 800 ka in the Early to early Middle Pleistocene. Facies characterizing a range of depositional processes are assigned to four facies associations (topset, foreset, bottomset and prodelta). The dominantly fluvial topset facies association has locally developed shallow marine (limestone) and fluvial‐shoreface sub‐associations. This delta represents a subsidence‐dominated system in which high fault displacement overwhelmed base‐level falls (creation of accommodation predominantly ≥ 0). Stratal geometries and facies stacking patterns were used to identify 11 key stratal surfaces separating 11 stratal units. Each key stratal surface records a landward shift in the topset breakpoint path, indicating a rapid increase in accommodation/sediment supply. Each stratal unit records a gradual decrease in accommodation/sediment supply during deposition. The cyclic stratal units and key stratal surfaces are interpreted as recording eustatic falls and rises, respectively. A 30 m thick package of foresets below the main delta records the nucleation of a small Proto‐delta probably on an early relay ramp. Based on changes in stratal unit geometries, the main delta is divided into three packages, interpreted as recording the initiation, growth and death of the controlling fault system. The Lower delta comprises stacked, relatively thin, progradational stratal units recording low displacement on the young fault system (relay ramp). The Middle delta comprises vertically stacked stratal units, each recording initial aggradation–progradation followed by progradation; their aggradational component increases up through the Middle delta, which records the main phase of increasing rate of fault displacement. The Upper delta records pure progradation, recording abrupt cessation of movement on the fault. A major erosion surface incising basinward 120 m through the Lower and Middle delta records an exceptional submarine erosion process (canyon or delta collapse).     

Evolution and architecture of a West Mediterranean Upper Pleistocene to Holocene coastal apron‐fan system

The Quaternary deposits of tectonically stable areas are a powerful tool to investigate high‐frequency climate variations (<10 ka) and to distinguish allogenic and autogenic factors controlling deposition. Therefore, an Upper Pleistocene–Holocene coastal apron‐fan system in north–western Sardinia (Porto Palmas, Italy) was studied to investigate the relations between climate changes, sea‐level fluctuations and sediment source‐supply that controlled its development. The sedimentary sequence records the strong influence of local (wet/dry) and worldwide (sea‐level) environmental variations in the sedimentation and preservation of the deposits. A multi‐disciplinary approach allowed subdivision of the succession into four major, unconformity‐bounded stratigraphic units: U1 U2, U3 and U4. Unit U1, tentatively dated to the warm and humid Marine Isotopic Stage (MIS) 5, consists of sandy, gravelly coastal/beach deposits developed during high sea‐level in low‐lying areas. Unit U2 consists of debris‐flow dominated fan‐deposits (ca 74 ka; MIS 4), preserved as partial fills of small valleys and coves. Unit U2 is mainly composed of reddish silty conglomerate to pebbly siltstones sourced from the Palaeozoic metamorphic inland hills (bedrock), superficially disintegrated during the preceding warm, vegetation‐rich MIS 5. The cold and semi‐arid climate strongly reduced vegetation cover along the valley flanks. Therefore, sediment gravity‐flow processes, possibly activated by rainstorms, led to deposition of debris‐flow dominated fans. Unit U3 consists of water‐flow dominated alluvial‐fan deposits (ca 47 to 23 ka; MIS 3), developed on a slightly inclined coastal plain. Unit U3 is composed of sandstone and sandy conglomerate fed from two main sediment sources: metamorphic inland bedrock and Quaternary bioclastic‐rich shelf‐derived sands. During this cold phase, sea‐level dropped sufficiently to expose bioclastic sands accumulated on the shelf. Frequent climate fluctuations favoured inland aeolian transport of sand during dry phases, followed by reworking of the aeolian bodies by flash floods during wet phases. Bedrock‐derived fragments mixed with water‐reworked, wind‐blown sands led to the development of water‐flow dominated fans. The Dansgaard–Oeschger events possibly associated with sand landward deflation and main fan formations are Dansgaard–Oeschger 13 (ca 47 ka), Dansgaard–Oeschger 8 (ca 39 ka) and Dansgaard–Oeschger 2 (ca 23 ka). No record of sedimentation during MIS 2 was observed. Finally, bioclastic‐rich aeolianites (Unit U4, ca 10 to 5 ka; MIS 1), preserved on a coastal slope, were developed during the Holocene transgression (ca 10 to 5 ka; MIS 1). The studied sequence shows strong similarities with those of other Mediterranean sites; it is, however, one of the few where the main MIS 4 and MIS 3 climatic fluctuations are registered in the sedimentary record.     

The Maesan fan delta, Miocene Pohang Basin, SE Korea: architecture and depositional processes of a high-gradient fan-delta-fed slope system

The Maesan fan-delta-fed slope system in the Miocene Pohang Basin occurs between two Gilbert-type fan deltas. Detailed analysis of sedimentary facies and bed geometry reveals that the sequence is represented by 13 sedimentary facies. These facies can be organized into three facies associations, representing distinct depositional environments: alluvial fan (facies association I), steep-faced slope (facies association II), and basin plain (facies association III). Subaerial debris flows and dense, inertia-dominated currents were transformed into subaqueous sediment gravity flows in steep-faced slope environments. Further downslope, these flows were channelized and formed lobate conglomerate and sandstone bodies at the terminal edge of the channels (or chutes). Interchannel and interlobe areas were dominated by homogeneous mudstone and muddy sandstone, deposited by suspension settling of fine-grained materials. Part of the steep-faced slope deposits experienced large-scale slides and slumps. The chutes/channels, lobes and splays on the steep-faced slope of the Maesan system are similar to those in modern subaqueous coarse-grained fan-delta systems.     

断陷湖盆浅水三角洲沉积特征:以Muglad盆地Unity凹陷Aradeiba组为例

浅水三角洲是沉积学和油气勘探开发领域的热点,目前研究主要集中在大型坳陷型盆地内,部分学者研究证明在断陷湖盆萎缩期或裂陷初期也存在浅水三角洲沉积,但研究较为薄弱.本文利用岩心、测井、地震以及分析化验资料,对Muglad盆地研究区内Aradeiba组浅水三角洲的沉积有利条件、沉积特征以及垂向演化特征进行了深入剖析,结合湖平...     

Soft‐sediment deformation structures in a Pleistocene glaciolacustrine delta and their implications for the recognition of subenvironments in delta deposits

The development of soft‐sediment deformation structures in clastic sediments is now reasonably well‐understood but their development in various deltaic subenvironments is not. A sedimentological analysis of a Pleistocene (ca 13·1 to 15 ¹⁰Be ka) Gilbert‐type glaciolacustine delta with gravity‐induced slides and slumps in the Mosty‐Danowo tunnel valley (north‐western Poland) provides more insight, because the various soft‐sediment deformation structures in these deposits were considered in the context of their specific deltaic subenvironment. The sediments show three main groups of soft‐sediment deformation structures in layers between undeformed sediments. The first group consists of deformed cross‐bedding (inclined, overturned, recumbent, complex and sheath folds), large‐scale folds (recumbent and sheath folds) and pillows forming plastic deformations. The second group comprises pillar structures (isolated and stress), clastic dykes with sand volcanoes and clastic megadykes as examples of water‐escape structures. The third group consists of faults (normal and reverse) and extensional fissures (small fissures and neptunian dykes). Some of the deformations developed shortly after deposition of the deformed sediment, other structures developed later. This development must be ascribed to hydroplastic movement in a quasi‐solid state, and due to fluidization and liquefaction of the rapidly deposited, water‐saturated deltaic sediments. The various types of deformations were triggered by: (i) a high sedimentation rate; (ii) erosion (by wave action or meltwater currents); and (iii) ice‐sheet loading and seasonal changes in the ablation rate. Analysis of these triggers, in combination with the deformational mechanisms, have resulted – on the basis of the spatial distribution of the various types of soft‐sediment deformation structures in the delta under study – in a model for the development of soft‐sediment deformation structures in the topsets, foresets and bottomsets of deltas. This analysis not only increases the understanding of the deformation processes in both modern and ancient deltaic settings but also helps to distinguish between the various subenvironments in ancient deltaic deposits.     

Cretaceous Sandbody Characters at Shallow‐Water Lake Delta Front and the Sedimentary Dynamic Process Analysis in Songliao Basin,China

Based on the abundant information from drilling, cores, and logging, the influence of topography, size of rivers and lakes, climate changes and the lake level’s fluctuation on the sandbodies at shallow-water delta front are systematically summarized and the sedimentary dynamic processes are analyzed. The interwell communication among the sandbodies and their planar distribution revealed from the hydrodynamic features of the development wells are integrated during the analysis. The fundamental requirements for the development of the shallow-water delta included flat topography and uniform subsiding rate. The delta plain was connected smoothly with the wide delta front and predelta, without the three-fold structure of topset, foreset, and bottomset as defined in the Gilbert Delta Model. Because of the weak fluvial effect and the lake energy is strong, the small and scattered shallow-water delta is destroyed by the scouring-backwashing, coastal current, and lake wave, resulting in the coastal sheet deposition. As the fluvial effect became stronger and the lake energy became weaker, the shape of the shallow-water deltas transferred from sheets to lumps and then branches.     

Evolution of a carbonate delta generated by gateway‐funnelling of episodic currents

Cool‐water carbonate sedimentation has dominated Mediterranean shelves since the Early Pliocene. Skeletal sand and gravel herein consist of remains of heterozoan organisms, which are susceptible to reworking due to weak early cementation in non‐tropical waters. This study documents the Lower Pleistocene carbonate wedge of Favignana Island (Italy), which prograded from a 5   km wide passage between two palaeo‐islands into a perpendicular, 10 to 15   km wide strait between the palaeo‐islands at one side and Sicily at the other during the Emilian highstand (1·6   Ma to 1·1   Ma). The clinoformed carbonate wedge, which is 50   m thick and 6   km long, formed by east/south‐east progradation of a platform on the submarine sill by currents that were funnelled between the two palaeo‐islands. Platform‐slope clinoforms evolved from initial aggradation (thin and low‐angle) into a progradation phase (thick and high‐angle). Both clinoform types are characterized by a bimodal facies stacking pattern defined by sedimentary structures created by: (i) subaqueous dunes associated with dilute subcritical currents; and (ii) upper‐flow‐regime bedforms associated with sediment‐laden supercritical turbidity currents. Focusing of episodic currents on the platform by funnelling between the islands controlled the downstream formation of a sediment body, here named carbonate delta. The carbonate delta interfingers with subaqueous dune deposits formed in the perpendicular strait. This study uses a reconstruction of bedform dynamics to unravel the evolution of this gateway‐related carbonate accumulation.     

Atlantic surface water inflow to the Nordic seas during the Pleistocene–Holocene transition (mid–late Younger Dryas and Pre‐Boreal periods, 12 450–10 000 a BP)

The inflow of Atlantic Water to the Nordic seas from mid–late Younger Dryas to earliest Holocene (12 450–10 000 a BP) is reconstructed on the basis of a high‐resolution core (LINK14) from 346 m water depth on the east Faroe shelf. We have analysed the distribution of planktic and benthic foraminifera, stable isotopes and ice‐rafted debris (IRD), and calculated absolute temperatures and salinities by transfer functions. During the investigated time period there was almost continuous inflow of Atlantic Water to the Nordic seas. Deposition of IRD during the mid–late Younger Dryas and Pre‐Boreal coolings indicates the presence of melting icebergs and that summer sea surface temperatures were low. The east–west temperature gradient across the Faroe–Shetland Channel was much steeper than today. The cold conditions around the Faroe Islands are attributed to stronger East Greenland and East Icelandic currents than at present. The near‐continuous inflow of Atlantic Water is consistent with published evidence suggesting that deep convection took place in the Nordic seas, although the convection sites probably had shifted to a more easterly position than at present. Around the time of deposition of the Saksunarvatn Tephra c. 10 350 a BP, sea surface temperatures increased to the present level. Copyright © 2011 John Wiley & Sons, Ltd.     

松辽盆地王府凹陷泉三、四段浅水三角洲沉积特征及模式

在岩心观察的基础上,结合测井、地震和区域背景资料分析,认为王府凹陷泉三、四段沉积时期普遍发育浅水三角洲沉积。由于受地形、古气候和水动力条件等多重因素的影响,研究区发育的浅水三角洲在沉积构造、沉积序列、微相类型、三角洲内部结构以及地球物理响应特征等方面呈现出与经典三角洲不同的沉积特征:具有建设性三角洲沉积特征,平面上呈网状,前缘相带延伸较远。具有相对发育的水下分流河道,河口砂坝欠发育;垂向上发育多次间断正韵律。紫红色泥岩大面积展布,生物扰动强烈;砂岩中发育强水动力浅水沉积构造,Gilbert型三角洲的3层结构不明显。浅水三角洲识别出两个亚相和7个微相。研究区具有良好的生储盖配置关系,利于岩性油气藏的形成,其中水下分流河道和分流河道砂体储层物性好,为最有利储层。     

Aggradation and carbonate accumulation of Holocene Norwegian cold‐water coral reefs

Cold‐water coral ecosystems present common carbonate factories along the Atlantic continental margins, where they can form large reef structures. There is increasing knowledge on their ecology, molecular genetics, environmental controls and threats available. However, information on their carbo‐nate production and accumulation is still very limited, even though this information is essential for their evaluation as carbonate sinks. The aim of this study is to provide high‐resolution reef aggradation and carbonate accumulation rates for Norwegian cold‐water coral reefs from various settings (sunds, inner shelf and shelf margin). Furthermore, it introduces a new approach for the evaluation of the cold‐water coral preservation within cold‐water coral deposits by computed tomography analysis. This approach allows the differentiation of various kinds of cold‐water coral deposits by their macrofossil clast size and orientation signature. The obtained results suggest that preservation of cold‐water coral frameworks in living position is favoured by high reef aggradation rates, while preservation of coral rubble prevails by moderate aggradation rates. A high degree of macrofossil fragmentation indicates condensed intervals or unconformities. The observed aggradation rates with up to 1500 cm kyr^?1 exhibit the highest rates from cold‐water coral reefs so far. Reef aggradation within the studied cores was restricted to the Early and Late Holocene. Available datings of Norwegian cold‐water corals support this age pattern for other fjords while, on the shelf, cold‐water coral ages are reported additionally from the early Middle Holocene. The obtained mean carbonate accumulation rates of up to 103 g cm^?2 kyr^?1 exceed previous estimates of cold‐water coral reefs by a factor of two to three and by almost one order of magnitude to adjacent sedimentary environments (shelf, slope and deep sea). Only fjord basins locally exhibit carbonate accumulation rates in the range of the cold‐water coral reefs. Furthermore, cold‐water coral reef carbonate accumulation rates are in the range of tropical reef carbonate accumulation rates. These results clearly suggest the importance of cold‐water coral reefs as local, maybe regional to global, carbonate sinks.     

浅水三角洲沉积体系与储层岩石学特征

浅水三角洲已经成为当前沉积学研究和油气勘探的重点领域,浅水三角洲常规和非常规砂岩储层中发现了丰富的油气资源。鄂尔多斯盆地中—古生界发育大型浅水三角洲沉积,结合岩芯、测井、分析化验等资料,对盆地西部地区山1—盒8段浅水三角洲的母岩特征、沉积充填、砂体展布与储层岩石学特征进行研究,为研究区常规砂岩储层和致密砂岩油气勘探提供地质依据。分析表明,研究区南部和北部砂岩重矿物组合相似,以锆石和白钛矿为主。综合La/Yb-REE与Dickinson三角图解、稀土元素配分模式和碎屑锆石定年分析认为,北部物源主要来自盆地西北部阿拉善古陆太古界和元古界花岗岩、片麻岩、石英砂岩,向南影响到陇东地区北部;南部物源主要来自盆地南部北秦岭地区太古界、元古界花岗岩、片麻岩和片岩,向北影响陇东地区中南部。山1段发育曲流河三角洲,盒8段发育辫状河三角洲,孤立型与垂向叠置型水下分支河道砂体是主要的砂体类型。盒8段沉积时期,古湖泊可能萎缩;南北物源形成的三角洲在研究区中部环县东南一带交汇混合。砂岩类型主要为岩屑质石英砂岩、石英砂岩和岩屑砂岩,结构成熟度中等—较差。砂岩成岩改造强烈,水—岩反应复杂,压实作用是储层致密化的主因,多期胶结作用使砂岩的孔喉结构变得十分复杂。孔隙类型以微米—纳米级的岩屑溶蚀孔、剩余粒间孔和高岭石晶间孔为主,整体上属于非常规致密砂岩储层。砂体分布与“甜点”预测是研究区致密油气勘探的关键。