波浪动力因素变化对沙质岸滩演变的影响

通过波浪水槽实验,对海平面变化造成的波浪动力因素改变引起的沙质岸滩形态响应开展机理性研究。实验采用1∶10单一沙质斜坡概化岸滩,利用3种不同实验水深模拟海平面变化,考虑椭圆余弦波、非规则波、规则波和孤立波4种类型波浪作用。实验对波浪在斜坡上的传播变形、破碎、上爬和回落过程的波高及波浪作用后的岸滩地形进行了测量。实验结果表明,椭圆余弦波、规则波和非规则波作用下,平衡岸滩呈现出滩肩形态,孤立波作用下则呈沙坝形态。海平面上升造成波浪动力增强,沙质岸滩平衡剖面形状基本保持不变向岸平移,槽谷、滩肩、沙坝位置以及岸线蚀退距离,均呈现出良好规律性。     

卷破波作用下沙质岸滩剖面形态判别式初探

通过波浪水槽实验,开展不同类型波浪作用下的沙质岸滩演化规律研究工作。本次实验研究不考虑比尺,采用1:10与1:20组成的复合沙质斜坡对岸滩进行概化,选取规则波和椭圆余弦波两种典型波浪作用,对波浪的传播、变形和破碎、上爬、回落过程以及波浪作用前后沙质岸滩床面地形进行了观测,探讨波浪作用下沙质岸滩剖面演化规律。本文实验工况中,规则波作用下,岸滩剖面呈现出沙坝剖面和滩肩剖面,椭圆余弦波作用下的岸滩剖面均呈滩肩形态,发现岸滩剖面形态不仅与波浪作用类型、强度、周期等因素相关,还与波浪破碎的强度等因素有关。通过对实验过程中现象的进行观察和分析,引入了卷破波水舌冲击角的概念。对波浪卷破破碎后形成的水流挟沙运动与岸滩剖面形态的关系进行定性分析,对水舌冲击角与Irribarren参数之间的关系进行定量分析,基于Irribarren参数与岸滩剖面形态的关系初步建立了波浪作用下沙质岸滩剖面形态判别关系式。通过本文实验结果和前人实验结果对趋势线进行拟合,求得其判别系数,判别式能够较好地划分淤积型岸滩、侵蚀型岸滩及过渡型岸滩三种岸滩形态。     

浅水极限波浪几何特征的实验研究

该文通过物理模型实验,对浅水区域内的波浪在破碎前极限状态下的几何特征进行了研究。实验基于JONSWAP谱对不规则波浪进行模拟,通过对波群中出现的单体极限波浪进行捕捉并对波形进行测量而得到研究样本。为了考察底坡因素对极限波浪几何特征的影响,实验共考虑了3组大小分别为β=1/15、1/30以及1/45的地形坡度。统计结果表明,在实验所采用的坡度范围内,当地波高与水深对近岸极限波浪的影响最为显著,随着水深与波高因素变化,极限波浪的几何特征也出现明显的改变。坡度因素对极限波陡和偏度的影响很小,可以被忽略,但是对不对称度参数的影响相对比较明显,坡度越陡,不对称程度越剧烈。最后,通过参数化,本文给出了极限波浪几何特征变化的经验公式。     

Physical impact on the reclamation area resulting from offshore dredging at the Changhwa coast, Taiwan

The physical impact of offshore dredging on the reclamation area at the Changhwa coast, Taiwan, is investigated using a three-dimensional movable-bed model test. A distorted modeling law consisting of maintaining similarity of the equilibrium beach profile between the model and prototype is proposed. The geometric distortion was verified through a series of preliminary experiments conducted in a wave flume. Experimental results show that the distorted modeling is able to reproduce the beach-face slope in nature. An appropriate long-term morphological time-scale was determined based on a comparison of model longshore littoral transport rates and equivalent prototype values. Seabed topographical changes before and after offshore dredging are evaluated in model tests. A suitable countermeasure to prevent beach erosion from wave attack along the reclamation area is suggested from the experimental results.     

Numerical modelling of erosion and accretion of plane sloping beaches at different scales

The paper focuses on the numerical simulation of erosion of plane sloping beaches by irregular wave attack in three wave flumes of different scales. One of the prime objectives of the tests was to provide a consistent data set for the improvement of numerical beach profile models. A practical application of this research with wave attack on plane sloping beaches is the erosion of the plane beaches after nourishment. Three models (CROSMOR, UNIBEST-TC and DELFT3D) have been used to simulate the flume experimental results focusing on the wave height distribution and the morphological development (erosion and deposition) along the beach profiles. Overall, the model predictions for wave heights show consistent results. Generally, the computed wave heights (H_rms and H_1/3) are within 10% to 15% of the measured values for all tests (under-prediction of the largest wave heights close to the shore). The three models can simulate the beach erosion of the wave flume tests (erosive tests) reasonably well using default values of the sand transport parameters. The model performance for the accretive tests is less good than that for the erosive tests. A practical field application of this research is the erosion of nourished beaches, as these beaches generally have rather plane beach slopes immediately after nourishment. Various graphs are given to estimate the beach erosion of nourished beaches.     

An experimental study on geometric characteristics of beach erosion profiles

The beach profile and sediment transport are very important factors in the design of coastal structures, and the beach profile is mainly affected by a number of parameters, such as wave height and period, beach slope, and the material properties of the bed. In this study, considering wave height (H₀=6.5, 11.5, 16, 20, 23, 26 and 30 cm), wave period (T=1.46 and 2.03 s), beach slope (m=1/10 and 1/15) and mean sediment diameter (d₅₀=0.18, 0.26, 0.33 and 0.40 mm), an experimental investigation of coastal erosion profile (storm profile) was carried out in a wave flume using regular waves, and geometric characteristics of erosion profile were determined by the resultant erosion profile. Dimensional and non-dimensional equations were obtained by using linear and non-linear regression methods through the experimental data and were compared with previously developed equations in the literature. The results have shown that the experimental data fitted well to the proposed equations with respect to the previously developed equations.     

Random wave runup and overtopping a steep sea wall: Shallow-water and Boussinesq modelling with generalised breaking and wall impact algorithms validated against laboratory and field measurements

A semi-implicit shallow-water and Boussinesq model has been developed to account for random wave breaking, impact and overtopping of steep sea walls including recurves. At a given time breaking is said to occur if the wave height to water depth ratio for each individual wave exceeds a critical value of 0.6 and the Boussinesq terms are simply switched off. The example is presented of waves breaking over an offshore reef and then ceasing to break as they propagate inshore into deeper water and finally break as they run up a slope. This is not possible with the conventional criterion of a single onset of breaking based on rate of change of surface elevation which was also found to be less effective generally. The runup distribution on the slope inshore of the reef was well predicted. The model is tested against field data for overtopping available for Anchorsholme, Blackpool and corresponding 1:15 scale wave flume tests. Reflection of breaking waves impacting a steep sea wall is represented as a partial reversal of momentum flux with an empirically defined coefficient. Offshore to nearshore significant wave height variation was reasonably predicted although nearshore model spectra showed distinct differences from the experiments. The breaking wave shape described by a shape parameter was also not well represented as might be expected for such a simple model. Overtopping agreement between model, field and flume was generally good although repeatability of two nominally identical flume experiments was only within 25%. Different distributions of random phase between spectral components can cause overall overtopping rates to differ by up to a factor of two. Predictions of mean discharge by EurOtop methods were within a factor of two of experimental measurements.     

海岸沙坝剖面和滩肩剖面特征研究

通过物理模型实验研究了海岸沙坝剖面和滩肩剖面的形成和演化过程,给出了稳定的沙坝剖面和滩肩剖面的几何特征。实验中考虑了两种初始坡度(1∶20和1∶10)和不同波高的规则波和不规则波,讨论了不同初始坡度海岸上破碎波空间分布特征。结果表明,沙坝产生后存在向岸和离岸两种运动形态,但最终将停留在稳定位置。稳定的沙坝剖面对应不同初始坡度和波浪存在不同的大沙坝和小沙坝分布。沙坝剖面由长时间小波高波浪序列作用后可转化为稳定滩肩剖面,该剖面不依赖于波浪和初始坡度。实验也给出了平衡剖面与理论曲线的对比以及剖面上泥沙粒径的分布。     

Establishing uniform longshore currents in a large-scale sediment transport facility

A large-scale laboratory facility for conducting research on surf-zone sediment transport processes has been constructed at the U.S. Army Engineer Research and Development Center. Successful execution of sediment transport experiments, which attempt to replicate some of the important coastal processes found on long straight beaches, requires a method for establishing the proper longshore current. An active pumping and recirculation system comprised of 20 independent pumps and pipelines is used to control the cross-shore distribution of the mean longshore current. Pumping rates are adjusted in an iterative manner to converge toward the proper settings, based on measurements along the beach. Two recirculation criteria proposed by Visser [Coastal Eng. 15 (1991) 563] were also used, and they provided additional evidence that the proper total longshore flow rate in the surf zone was obtained. The success of the external recirculation system and its operational procedure, and the degree of longshore uniformity achieved along the beach, are the subjects of this paper. To evaluate the performance of the recirculation system, and as a precursor to sediment transport experiments, two comprehensive test series were conducted on a concrete beach with straight and parallel contours (1:30 slope), one using regular waves and the other using irregular waves. In the regular wave case, the wave period was 2.5 s and the average wave height at breaking was approximately 0.25 m. In the irregular wave case, the peak wave period was 2.5 s and the significant breaking wave height was approximately 0.21 m. The longshore current recirculation system proved to be very effective in establishing uniform mean longshore currents along the beach in both cases. This facility and the data presented here are unique for the following reasons: (1) the high cross-shore resolution of the recirculation system and the ease with which changes can be made to the longshore current distribution, (2) the degree of longshore uniformity achieved as a percentage of the length of the basin (even near the downdrift boundary), (3) the scale of the wave conditions generated, and (4) the relatively gentle beach slope used in the experiments (compared to previous laboratory studies of the longshore current). Measured data are provided in an appendix for use in theoretical studies and numerical model development and validation.     

Estimation of incident and reflected waves in regular wave experiments

This paper presents a laboratory technique for measurement of reflected waves by a submerged horizontal plate. A simple method is proposed to decompose the composite wave record obtained from the wave reflection experiments in the wave flume. The data collected were used to compute the reflected wave height by means of two and three probe methods proposed by other investigators and compared with the directly computed reflected wave using the measured incident wave. The experiment was carried out for a horizontal plate of 1 m length spanning the full width of the flume with wave periods ranging from 0.8 to 1.8 sec with 0.1 sec increments and wave heights of 5, 10 and 15 cm. The methods using two and three probes with phase measurement yield better results than the three probe method without phase measurement, and in general they have a wider range of application. The method using three probes without the phase measurement generally fails due to numerical instability of the scheme. The results obtained by the proposed method are compared with the two and three probe methods and a comparative analysis of the four methods is presented and discussed.     

Wave run-up and overtopping on smooth and rough slopes of coastal structures

A series of hydraulic model tests has been carried out in a glass wave flume to investigate the influences of wave height, wave period, wave steepness, surf similarity parameter, roughness, layer thickness and porosity on wave run-up and overtopping of 1:2 sloped impermeable and permeable breakwaters fronted by a 1:10 gentle, smooth beach slope. The analysis of results involves the correlation between the overtopping energy transfer with the relative wall height and the relationship between wave run-up and overtopping rate. Further, measured wave run-up and overtopping rates are compared with the results given in the Shore Protection Manual (1984), Automated Coastal Engineering System (1992)and results of other investigators.     

Longshore sorting on a beach under wave action

Sorting of sediment on a beach under wave action takes several forms. Stratified layers of finer and coarser sediment, which depend on wave climate, grain size and beach slope are formed. This complex problem can be simplified by defining the cross-shore and longshore sorting according to the angle between the breaking wave and the coast. In the present study, longshore distribution of sediment as well as corresponding beach profiles was measured in a wave basin. Three-dimensional hydraulic model experiments were performed with regular waves. Eighteen sets of experiments performed in longshore sorting mechanism using two different sand beds. The sorting of the bed material and the formation of armour coats along the beach were defined by grain size distributions and dimensionless parameters for sandy beaches.The rate of sediment transport with grain size sorting was measured in a wave basin. A method introduced sorting process was presented in this study. The sediment rate based on sorting mechanism was also discussed with known methods. It has been found that the non-uniformity of the grain size and hence sorting of the beaches play a very important role in the sand transport due to wave motion in a similar way to the case of steady flow in alluvial channels.     

On the evolution and run-up of breaking solitary waves on a mild sloping beach

This paper presents new laboratory experiments carried out in a supertank (300 m × 5 m × 5.2 m) of breaking solitary waves evolution on a 1:60 plane beach. The measured data are employed to re-examine existing formulae that include breaking criterion, amplitude evolution and run-up height. The properties of shoreline motion, underwater particle velocity and scale effect on run-up height are briefly discussed. Based on our analyses, it is evidently found that there exist five zones during a wave amplitude evolution course on the present mild slope. A simple formula which is capable of predicting maximum run-up height for a breaking solitary wave on a uniform beach with a wide range of beach slope (1:15–1:60) is also proposed. The calculated results from the present model agree favorably with available laboratory data, indicating that our method is compatible with other predictive models.     

Experimental simulation of shoreface nourishments under storm events: A morphological,hydrodynamic, and sediment grain size analysis

This study focuses on barred beach shoreface nourishments physically simulated in a wave flume. The attack of a schematic storm on three different nourishments is analysed. The apex and waning storm phases lead respectively to offshore and onshore sediment transports. Nourishments in the trough and on the outer bar feed the bar and increase wave dissipation offshore. The bar acts as a wave filter and reduces shore erosion (lee effect). In contrast, nourishment on the beach face leads mostly to shore feeding and reconstruction (feeder effect). With successive nourishments, the beach face clearly becomes steeper and onshore sediment transport is reduced during moderate wave climates. The surface grain size analysis reveals marked variations. Coarser sediments are sorted on the bar and the upper beach face. These locations correspond to large wave dissipation zones during the storm apex.     

海岸破波带内悬沙空间分布试验研究和解析表达式

关于海岸破波带内悬沙浓度水平和垂向分布的研究对于计算海岸输沙率和地形演变具有重要意义。本研究进行了规则波、波群和不规则波三种波浪情况破波带内悬沙浓度的水平和垂向分布的试验测量。试验在大尺度波浪水槽进行,接近实际海岸波况尺度。给出了破波带内多断面悬沙垂向分布的细致测量结果,并以此为基础给出了预报实际海岸破波带内悬沙浓度水平和垂向分布解析表达式,讨论了形成这些分布的物理原因和不同波况、不同破波带区域对分布的影响。     

Experimental and Numerical Study of Wave-Induced Long-Shore Currents on A Mild Slope Beach

1.Introduction Long shorecurrenthasbecomethesubjectofextensiveworldwideresearchformanyyears.The purposeofthestudyistounderstandandpredicttheprocessesofsedimenttransport,shorelineevolu tionandpollutanttransportinthenear shorezoneundertheactionofwaves.Goda(2001)regarded thesuspendedsedimentastheprincipalloadinsedimenttransportandtheeffectoflong shorecurrents wasemphasized.Theeffectofwavesonpollutanttransportwasstudiedbynumericalmodelandfield experiment(TaoandHan,2002;Rodriguezetal.,1995),andth…     

Parameterization of nonlinear shallow water waves over sloping bottoms

Investigation of the bottom slope effects on the nonlinear transformation of irregular waves, which are generated based on JONSWAP spectra, is carried out in a physical wave flume with three slopes (β = 1/15, 1/30, 1/45). The slope effects on the estimation of representative wave height are examined first. To obtain a better estimation of wave height, the slope effect should be considered when slope is larger than 1/30. The nonlinear parameters (bicoherence, skewness and asymmetry) are estimated by using the wavelet-based bispectrum, and the empirical formulae regarding these nonlinear parameters as a function of the local Ursell number are derived based on the present data measured on each slope. The results indicate that the slopes have a negligible effect on the variations of the skewness. The fitted coefficients of the formulae for the other parameters on slope β = 1/15 are clearly different from the results on the slopes β = 1/30 and 1/45, indicating that slope influence on the parameterization cannot be ignored when β > 1/30. Hence, new formulae considering the slope effect are presented. Furthermore, the empirical formulae for the data in surf zone are recommended.     

Measured and modeled wave overtopping on a natural beach

The rate of wave overtopping of a barrier beach is measured and modeled. Unique rate of wave overtopping field data are obtained from the measure of the Carmel River, California, lagoon filling during a time when the lagoon is closed-off with no river inflow. Volume changes are based on measured lagoon height changes applied to a measured hypsometric curve. Wave heights and periods are obtained from directional wave spectra data in 15 m fronting the beach. Beach morphology was measured by GPS walking surveys. Three empirical overtopping models by Van der Meer and Janssen (1995), Hedges and Reis (1998) and Pullen et al. (2007) with differing parameterizations on wave height, period and beach slope and calibrated using extensive laboratory data obtained over plane, impermeable beaches are applied in a quasi-2D manner and compared with the field observations. Three overtopping events are considered when morphology data were available less than 2 weeks prior to the event. The models are tuned to fit the data using a reduction factor to account for beach permeability, berm characteristics, non-normal wave incidence and surface roughness influence. In addition, the run-up model by Stockdon et al. (2006) based on field data is examined and found to underestimate run-up as the calculated values were too small to predict any of the observed overtopping. The three overtopping models performed similarly well with values of 0.72–0.87 for the two narrow-banded wave cases, with an average reduction factor of 0.78. The European model (Pullen et. al., 2007) performed best overall and in particular for the case of the broad-banded, double peaked wave spectrum.     

楮岛沙滩不同时间尺度变化特征与波能流密度相关性探讨

在波浪和水流的作用下,泥沙在不同时间尺度下的运动会引起沙滩的冲淤演变,对海岸资源有重要的影响。因此,了解沙滩季节性演变规律,并采取针对性的防护措施,是近岸沙滩亟须解决的问题。目前,现场观测是研究沙滩剖面冲淤演变的重要方法,通过沉积物组成、岸滩坡度及波浪动力的时空变化,了解沙滩剖面的变化特性,对于沙滩管理和海岸保护具有十分重要的意义。基于2017年9月—2019年11月在荣成楮岛南岸沙滩每个月采集一次的剖面数据,以及波浪动力数据,分别探究了沙滩在不同时间尺度下的变化特征,并对沙滩变化特征与波浪动力因素的相关性进行了探讨。研究发现：楮岛南岸沙滩形态变化具有较强的季节性特征,春季沙滩比较稳定;夏季沙滩受台风影响侵蚀严重,但在风暴过后的短时间内,沙滩泥沙恢复较快;冬季沙滩恢复速度逐渐减缓并趋于稳定。在夏季和冬季期间,波能流密度的向岸分量对楮岛南沙滩的演变产生重要作用,而且波能流密度向岸分量的均值（选取数据采集前15 d的波浪条件参与计算）与沙滩体积的相关性最好,并给出了两者的线性拟合公式。