广州市排水管道检测结果分析及修复技术选择

为确定适合广州市地下排水管道的修复方法,对广州老城区近100kin2地区进行调查。调查采用管道潜望镜（Quick View,QV）、管道闭路电视（closed—Circuit Television,CCTV）、管道声纳（Sonar）进行综合探测,结果表明,调查区域内的地下排水管道存在的主要问题是破损断裂、错位、路基下沉、管道淤塞现象,其中小直径管道的损坏情况较为严重,尤其是300mm的管道将近报废。针对地下排水管道的调查情况,结合现有修复技术的特点,经过对修复成本及施工的难易性的研究讨论,得出适合多种管道和缺陷类型的翻转内衬法（Cured In Place Pipe,CIPP）和施工要求相对简单的U型折叠法（U-fold）满足要求,并能够产生较高经济社会效益。     

围堰工程对污水管线影响的数值模拟与评估

城市内新建工程周边环境复杂,地下管线种类繁多,在设计之初就需要考虑施工以及工程营运对其安全的影响,但目前缺乏统一的影响评价标准,须按照管线功能以及所属部门的相关规程作为其评价依据。该项目的管线为下穿围堰的2条直径为1.2 m、壁厚为12 mm的排污管,采用FLAC3D建立了围堰工程对大直径有压焊接薄壁排污管道的三维数值计算模型,分4种不同施工工况进行了管道变形和应力计算。依据相关规范的要求,从管道本身的安全性和正常使用要求出发,并采用第4强度理论计算了相当应力,最大值为136.61 MPa,出现在最后抽水工况下管1的外侧。最大沉降量39.3 mm对应的管体倾斜量为0.275%。将其结果与理论值进行对比,理论计算得到的相当应力最大值为188.18 MPa,高于数值计算结果,其原因为理论方法将各影响效应分别计算并进行简单相加。结果表明,拟建围堰工程对该管线的影响可控,数值方法较规范方法计算结果更为合理,为类似工程对管线影响评价提供了参考。     

一维均质与非均质土柱中溶质迁移的分数微分对流-弥散模拟

分数微分对流-弥散方程(FADE)是模拟溶质迁移问题的新理论,但应用FADE来模拟溶质迁移时能否克服弥散的尺度效应尚待验证。利用长土柱实验资料结合FADE的解析解拟合推求FADE的弥散系数,并分析其与尺度之间的相关关系。研究结果表明,FADE的弥散系数具有随尺度增大而增大的现象,且均质土柱中FADE的弥散系数尺度效应小于非均质土柱中弥散系数尺度效应。在均质土柱中,弥散系数与尺度之间成指数相关关系,在非均质土柱中,弥散系数与尺度之间成幂相关关系。考虑了弥散系数分别与迁移时间和迁移距离呈线性递增两种相关关系,进而分别构建了3种考虑弥散尺度效应的FADE模型,并提出了求解的差分方法。利用上述3种考虑弥散尺度效应的FADE来模拟和预测不同空间位置处的溶质迁移过程。结果表明,对均质土柱中的溶质迁移可得到较好的模拟结果;对于非均质土柱,其模拟结果与实测结果仍然存在一定的差异。     

倾斜布管采控天然冷量的青藏铁路路基温度场演变规律

Aiming at the stabilization of Qinghai-Tibetan Railway embankment during its construction and run, the method using tilt pipes to keep the permafrost embankment stabilization is put forward in the paper. By gathering natural cold energy in the winter and release it in the summer the tilt pipes can keep the permafrost embankment stabilizing. The temperature fields of the embankment and the stratums below are studied according to the condition of pipes diameter 250mm, length 7. 0m and tilt angle 30°,45°, 60° until the railway working for 20 years. It is shown that the embankment field using tilt pipes will eliminate the thawing core and come into subzero temperature phase ahead of 9 years compared with the original model. Different tilt angles have different efforts on the embankment and stratums, synthesis analysis of thermal income and expenses of the embankment and stratums should be carried out     

Steady infiltration from buried point source into heterogeneous cross‐anisotropic unsaturated soil

The paper presents the analytical solution for the steady‐state infiltration from a buried point source into two types of heterogeneous cross‐anisotropic unsaturated half‐spaces. In the first case, the heterogeneity of the soil is modelled by an exponential relationship between the hydraulic conductivity and the soil depth. In the second case, the heterogeneous soil is represented by a multilayered half‐space where each layer is homogeneous. The hydraulic conductivity varies exponentially with moisture potential and this leads to the linearization of the Richards equation governing unsaturated flow. The analytical solution is obtained by using the Hankel integral transform. For the multilayered case, the combination of a special forward and backward transfer matrix techniques makes the numerical evaluation of the solution very accurate and efficient. The correctness of both formulations is validated by comparison with alternative solutions for two different cases. The results from typical cases are presented to illustrate the influence on the flow field of the cross‐anisotropic hydraulic conductivity, the soil heterogeneity and the depth of the source. Copyright © 2004 John Wiley & Sons, Ltd.     

用分段定向钻进方法铺设弧形轨迹集束管

横穿开洛高速公路６５．４ｍ,贯通９个收费亭人井,１１段路基,按路面形状成中间高,两端低的菜钻孔;多级扩孔至孔径５００ｍｍ,在其中铺设Х１１４ｍｍ钢管４根,Х６０ｍｍ钢管３根。两组这样的管束平行间距始终保持４５０ｍｍ,按轨迹设计要求,准确无误的到达出口。     

Fine-grained colliery discard and its susceptibility to liquefaction and flow under cyclic stress

A spectrum of fine-grained colliery discards (tailings and slurries) has been tested in a cyclic loading triaxial rig.

The granular types are shown to be the most susceptible to liquefaction, compared with the more plastic discards which exhibit a slow build-up in pore-water pressure and gradual drop in effective stress with increasing shear strain. Plasticity index is consequently advocated as a useful physical parameter in assessing the general liquefaction potential of sediments of this type.

Observations of the mobile or “flowing” discards following liquefaction suggest that effective stress is the most important determinant of apparent viscosity. The post-liquefaction behaviour is believed to be pertinent to other inertia flows observed in nature.     

Detection of contaminant plumes released from landfills: numerical versus analytical solutions

Contaminant leaks released from landfills are a threat to groundwater quality. The groundwater monitoring systems installed in the vicinity of such facilities are vital. In this study the detection probability of a contaminant plume released from a landfill has been investigated by means of both a simulation and an analytical model for both homogeneous and heterogeneous aquifer conditions. Since the detection probability is a sensitive quantity, we first compare the two methods for homogeneous aquifer conditions to assess the errors that are encountered by performing simulations. The analysis shows that the simulation model yields the detection probabilities of a contaminant plume at a given monitoring well quite well in the homogeneous case. For heterogeneous aquifers we apply the approximated analytical model based on macro-dispersivities. Here we find that this model is insufficient in monitoring system design, since the obtained analytical values of the detection probabilities at a given monitoring well differ significantly from those computed by simulation.     

Classifications of retail stores and shopping centres: some methodological issues

This paper reviews current methods used in classifying retail outlets and areas devoted to retailing, in the geographical and town planning literature. For retail outlets, classifications based upon types of goods sold, and types of shopping trip, are discussed. This is followed by an analysis of modern large store development which reflects property developers' and retailers' concerns. Areas devoted to retail uses are subdivided into unplanned ‘retail areas’ and planned ‘shopping centres’. Traditional classifications based upon central place theory are reviewed for both of these types, and found wanting in the light of recent changes in retail development practice and consumer behaviour. Classifications based upon physical development characteristics and type of shopping trip are recommended. Finally, classifications of urban retail location are examined. This revised version was published online in July 2006 with corrections to the Cover Date.     

潜孔锤钻进孔口密封器流场数值模拟及优化设计

为定向收集风动潜孔锤钻进时排出的岩矿样,降低粉尘污染同时提高岩矿样采取率,对孔口密封器内流场进行了计算流体动力学分析（CFD）,分别讨论了传统密封器、隔板式密封器、流线型式密封器结构形式及其相关结构参数（隔板位置L、出口直径d、出口角度θ）对密封效果的影响规律并进行优化设计。分析表明,三类密封器密封效果受结构形式和出口直径d影响最为明显:当d为40～160 mm时,隔板式和流线式密封器密封效果远好于传统密封器;当d>160 mm时,隔板式密封器与传统密封器的效果相当,而流线式密封器的效果始终是三者当中最好的。经现场试验证明,采用优化过的孔口密封器对岩矿样实施定向收集,除尘效果很好,且岩矿样平均采取率可达97%。     

Raman spectroscopy at high pressure and high temperature. Phase transitions and thermodynamic properties of minerals

An outline of recent developments in Raman spectroscopy at high pressure, high temperature and combined high pressure and high temperature is presented. The instrumental and technical aspects of Raman spectroscopy, and coupling of diamond anvil cells and miniature furnaces to Raman microspectrometers are discussed. Some potential pitfalls, such as the thermal pressure in laser heated diamond anvil cells or the thermal radiation during high-temperature measurements, are presented. Special emphasis is given on processing of high-temperature Raman data. New recently discovered phase transformations in the SiO₂ system (quartz→ quartz II, pressure-induced amorphization of quartz) and structural changes in SiO₂ glass and melt are used to infer the capability of in-situ Raman spectroscopy for determining the microscopic behaviour of minerals, melts and glasses under extreme pressure and temperature conditions. Finally, it is shown how vibrational mode anharmonicity can be obtained from the pressure- and temperature-induced shifts of Raman modes. This anharmonicity can be introduced into the vibrational modeling of the thermodynamic properties (entropy and equation of state) of minerals. The example of calcite is briefly discussed.     

Optimization of the freeze pipe arrangement and the necessary refrigeration plant capacity by a femcomputer program

The number and the arrangement of freeze pipes and the energy needed to freeze a certain amount of soil are important factors for the economic success of a freeze project. A thermal design in which these factors are considered is based on the solution of a nonlinear unsteady heat conduction equation including phase transition. The equation is solved by means of a finite-element-method (FEM), considering boundary conditions related to artificial ground freezing.

In this paper the basic mathematical techniques to deal with the transient heat conduction problem, with temperature-dependent soil properties, and the release of latent heat are described. The significance of the convective heat transfer coefficient and the temperature distribution in the coolant running through the freeze pipes are shown and their dependencies to other factors as refrigeration plant capacity or type of flow in the pipes are considered. Finally an example is presented.     

Continuum model for simultaneous chemical reactions and mass transport in hydrothermal systems

A time-space continuum model for transport of hydrothermal fluids in porous media is presented which provides for simultaneous, reversible and irreversible chemical reactions involving liquids, gases and minerals. Homogeneous and heterogeneous reactions are incorporated in the model in a similar fashion through source/sink terms added to the continuity equation. The model provides for moving reaction fronts through surfaces of discontinuity across which occur jump discontinuities in the various field variables satisfying generalized Rankine-Hugoniot relations. Reversible reactions including aqueous complexing, oxidation-reduction reactions, mineral precipitation and dissolution reactions and adsorption are explicitly accounted for by imposing chemical equilibrium constraints in the form of mass action equations on the transport equations. This is facilitated by partitioning the reacting species into primary and secondary species corresponding to a particular representation of the stoichiometric reaction matrix referred to as the canonical representation. The transport equations for the primary species combined with homogeneous and heterogeneous equilibria result in a system of coupled, nonlinear algebraic/partial differential equations which completely describe the evolution of the system in time. Spatially separated phase assemblages are accommodated in the model by altering the set of independent variables across surfaces of discontinuity. Constitutive relations for the fluid flux corresponding to primary species are obtained describing transport of both neutral and charged species by advection, dispersion and diffusion. Numerical implementation of the transport equations is considered and both explicit and implicit finite difference algorithms are discussed. Analytical expressions for the change in porosity and permeability with time are obtained for an assemblage of minerals reacting reversibly with a hydrothermal fluid under quasi-steady state conditions. Fluid flow is described by Darcy's law employing a phenomenological expression relating permeability and porosity. Finally an expression for the local retardation factor of solute species is derived for the case of advective transport in a single spatial dimension which accounts for the effects of homogeneous and heterogeneous equilibria including adsorption on the rate of advance of a reaction front. The condition for the formation of shock waves is given.     

Strain softening of K0-consolidated Changi sand under plane-strain conditions

Experimental results are presented in this paper to study the strain softening behaviour of a marine dredged sand under plane-strain conditions. K₀ consolidated drained and undrained tests were conducted using a new plane-strain apparatus to characterize the strain softening behaviour of the sand under plane-strain conditions. For medium dense specimens, strain softening and shear bands were observed to occur under both drained and undrained conditions. For very loose specimens, no shear bands were observed and critical states were reached within the homogeneous deformation region in both drained and undrained tests. Strain softening was observed to occur at small strain for very loose specimens under undrained conditions. Two types of strain softening, the homogenous softening and banding softening, were identified and the conditions for strain softening were established. The results obtained from this study were compared with the studies by Han and Vardoulakis (Géotechnique 41(1):49–78, 1991), Finno et al. (J Geotech Eng ASCE 122(6):462–473, 1996, Géotechnique 47(1):149–165, 1997) and Mokni and Desrues (Mech Cohes-Frict Mat 4:419–441, 1998).     

Characterizing the rheology of laterite slurries

The viscous behaviour of laterite slurries was characterized by measurements of shear stress at constant and changing shear rates. Steady state stresses were obtained after accounting for the settling solids: the values show that the fluids possess viscosities of order 100 mPa s and are moderately shear-thinning, for solid volume fractions from 0.06 to 0.18 and for shear rates between 10 and 1000 s⁻¹. Transient stress measurements were made for steps down in shear rate and for ramps down and up in shear rate. It was found that the Bingham–Maxwell model provides good fits to the transient data, both at low concentrations, where yield behaviour is dominant, and at high concentrations, where elasticity is dominant. For volume fractions of 0.10 or greater, relaxation times were found from step tests to be of order 10 s, but relaxation times found from the ramp tests were generally several times higher.     

A constitutive law for rock salt based on creep and relaxation tests

Summary The paper deals with uniaxial relaxation tests on rock salt which are the basis for a constitutive equation. Since so far no regard was paid to relaxation behaviour, corresponding test results are not available and hence a special device for performing of uniaxial relaxation tests had to be constructed. Some interesting test results are discussed in the paper. These results are useful for the verification of constitutive equations. A critical analysis of conventional constitutive laws and their fundamentals shows that these material laws have considerable imperfections and are rested on substantial restrictions. Particularly, they are not able to describe relaxation behaviour sufficiently. Consequently, a constitutive law is proposed consisting of a strain hardening approach with separate creep and relaxation functions. By post-calculation of different laboratory tests it could be shown that in comparison to conventional steady-state creep equations this material law describes the viscous behaviour of rock salt more realistically.     

Stochastic analysis of the effect of heterogeneity and fractures on radionuclide transport in a low-permeability clay layer

Deep low-permeability clay layers are considered as safe environments for disposal of high-level radioactive waste. In Belgium, the Boom Clay is a candidate host rock for deep geological disposal. In this study, we analyze the effects of fractures and spatially variable hydraulic conductivity on radionuclide migration through the clay. Fracture geometry and properties are simulated with Monte Carlo simulation. The heterogeneity of hydraulic conductivity is simulated by direct sequential co-simulation using measurements of hydraulic conductivity and four types of secondary variables. The hydraulic conductivity and fracture simulations are used as input for a transport model. Radionuclide fluxes computed with this heterogeneous model are compared with fluxes obtained with a homogeneous model. The output fluxes of the heterogeneous model differ at most 8% from the homogeneous model. The main safety function of the Boom Clay is thus not affected by the fractures and the spatial variability of hydraulic conductivity.     

Vertical deformation of rigid foundations of arbitrary shape on layered soil media

A numerical procedure is described for the analysis of vertical deformation of smooth, rigid foundations of arbitrary shape on homogeneous and layered soil media. The contact area at the interface of the foundation and soil medium is approximated by square subdivisions. The response of the system is then obtained from the superposition of the influence of the individual subdivisions. The flexibility influence coefficients are based on equivalent smooth, rigid circular areas with the same contact area as the square subdivisions. For foundations on a homogeneous, isotropic elastic half-space, the flexibility coefficients are given analytically by the integrated forms of the Boussinesq's solution. For a layered soil medium, the flexibility coefficients are determined from an axisymmetric finite element analysis which is essentially two dimensional. Thus, there is no necessity for a full three-dimensional finite element analysis. Comparison with solutions obtained using the integral transform technique for smooth, rigid rectangular foundations on a homogeneous, isotropic elastic half-space shows good agreement. Parametric solutions are presented for the response of rectangular foundations on some ‘typical’ soil profiles. The use of a simplified method to estimate the settlement of rectangular foundations on a layered soil medium by superposing solutions for homogeneous, elastic strata is discussed.     

金伯利岩和钾镁煌斑岩的磁性特征与航空磁测普查效果

讨论了国内外用磁法普查金伯利岩的问题。与现代质子磁力仪的精度相适应,金伯利岩按磁性分为四类:实际无磁性的、弱磁性的、磁性的、强磁性的。大多数金伯利岩和钾镁煌斑岩是弱磁性的或磁性的。金伯利岩管的磁性无论在平面上和沿深度都是不均匀的。航空磁测普查金伯利岩和钾镁煌斑岩取得良好效果的3个条件中,最重要的是围岩磁性干扰水平低。