Studies of electrical properties of rocks under high temperature and pressure

Studies of the rocks′ electrical properties under high temperature and pressure have found favors in the geophysicist′s eyes, because those studies are becoming to be the important methods to understand the earth′s interior materials, their migration and evolution. This article introduces the development and significant of those studies from the measurements, instruments and affections, etc.     

The experimental studies on electrical con-ductivities and P-wave velocities of anortho-site at high pressure and high temperature

Introduction The measurements of the compressional wave velocity and electrical conductivity of minerals and rocks are of fundamental importance to look into the earths interior, including composition, geotherm, generation and distribution of fluids and melts. Hydrous minerals formed by metamatu-siom are abundant within the earth. Previous studies have been carried out on the dehydration effect on the electrical conductivity and wave velocity of rocks such as serpentine, amphibole, most of whi…     

高温高压下麻粒岩电导率研究

麻粒岩是下地壳的重要组成物质,模拟其在下地壳温压条件下的电导率对于认识下地壳的电导率分布具有十分重要的意义.本文用交流法在1 GPa下,373~1002 K范围内研究了麻粒岩样品的复阻抗,并且对测量结果进行了阻抗谱分析.研究结果表明,复阻抗对频率具有依赖性,且随温度的升高,复阻抗的实部、虚部均变小.在实验给出的温度范围内,电导率结果符合Arrhenius关系式.当温度在373~663 K范围内时,实验所获得的激化焓为0.31 eV,表明样品的电导率由低能带杂质离子所控制;当温度在673~1002 K范围内时,激化焓为0.67 eV,此时可能为小极化子导电.将所得电导率结果与西南峨边—马边地区以及华北应县―商河地区的大地电磁结果进行了对比,发现在所模拟的下地壳温压范围内,实验室测得的电导率位于野外MT数据范围内.     

高温高压下上地幔岩石电导率实验研究

为了建立具有普遍适用性的上地幔电性结构,本文利用Kawai-1000t压机和Solartron IS-1260阻抗/增益-相位分析仪,在4.0~14.0 GPa、873~1673 K的条件下,采用交流阻抗谱法（频率范围10^-1~10⁶Hz）测量了不含水的地幔岩电导率.实验结果显示,岩石的电导率随温度升高而大幅度的增大;在较大的温度范围内岩石的导电机制发生了变化,中低温时为小极化子导电,此时激活焓为0.94 eV（±0.13）eV,激活体积为0.11（±0.92）cm³·mol^-1,高温时为和镁空穴相关的离子导电,此时激活焓为1.6~3.17 eV,激活体积为6.75（±7.43）cm³·mol^-1;本次测量的电导率比低压下岩石的电导率要高,比矿物的电导率也要高.用本次的实验结果回归计算得到Fennoscandian地区的上地幔的一维电导率剖面,发现200 km以上本次实验计算的结果和大地电磁测深的电导率剖面吻合的比较好,在200 km以下本次实验得到的要比野外测量的电导率稍稍高一点,可能是因为实验过程中没有完全避免水的影响.本次的实验结果比用有效均匀介质方法计算得到的pyrolite矿物模型的电导率要高出两个数量级,这样的结果显示只用一种矿物的电导率或是几种矿物理论计算的结果有一定的不合理性.

     

高温高压下上地幔岩石电导率实验研究

为了建立具有普遍适用性的上地幔电性结构,本文利用Kawai-1000t压机和Solartron IS-1260阻抗/增益-相位分析仪,在4.0~14.0 GPa、873~1673 K的条件下,采用交流阻抗谱法（频率范围10^-1~10⁶Hz）测量了不含水的地幔岩电导率.实验结果显示,岩石的电导率随温度升高而大幅度的增大;在较大的温度范围内岩石的导电机制发生了变化,中低温时为小极化子导电,此时激活焓为0.94 eV （±0.13） eV,激活体积为0.11（±0.92） cm³·mol^-1,高温时为和镁空穴相关的离子导电,此时激活焓为1.6~3.17 eV,激活体积为6.75（±7.43） cm³·mol^-1;本次测量的电导率比低压下岩石的电导率要高,比矿物的电导率也要高.用本次的实验结果回归计算得到Fennoscandian地区的上地幔的一维电导率剖面,发现200 km以上本次实验计算的结果和大地电磁测深的电导率剖面吻合的比较好,在200 km以下本次实验得到的要比野外测量的电导率稍稍高一点,可能是因为实验过程中没有完全避免水的影响.本次的实验结果比用有效均匀介质方法计算得到的pyrolite矿物模型的电导率要高出两个数量级,这样的结果显示只用一种矿物的电导率或是几种矿物理论计算的结果有一定的不合理性.     

高温高压下地幔岩和苦橄质榴辉岩的电导率实验

为了探讨地幔岩模型和苦橄质榴辉岩模型在上地幔存在的合理性,建立上地幔的电性结构,本文利用YJ-3000t紧装式六面顶压机和Solartron IS-1260阻抗/增益-相位分析仪,在1.0~4.0 GPa、700~1150℃的条件下,采用交流阻抗谱法(频率范围10-1~106 Hz)分别测量了地幔岩和苦橄质榴辉岩的电导率.实验结果表明:随着温度的升高,地幔岩和苦橄质榴辉岩的电导率大幅增加;随着压力的增大,地幔岩的电导率略有增加,活化体积ΔV为-4.73 cm3·mol-1,而苦橄质榴辉岩的电导率几乎没有变化,活化体积ΔV为-0.11 cm3·mol-1;在电性方面,用苦橄质榴辉岩来表示深部的物质较为合理,地幔岩解释浅部可能更恰当,但浅部物质的分布不均匀,电导率随深度的变化主要受控于温度的影响,其次才是成分.     

高温高压下角闪片麻岩的电导率研究

在1.0 GPa压力、343～962 K温度和0.1～106Hz频率的条件下,使用Solartron 1260阻抗-增益/相位分析仪对含角闪石的片麻岩从平行和垂直面理两个不同方向分别进行了电阻抗的测定,并且进一步分析了片麻岩的微观导电机制.高温高压实验结果表明:片麻岩的复阻抗对温度、频率表现出明显的依赖性.片麻岩的电导...     

高温高压下碳酸盐熔体对地幔岩电导率的影响

为了观测含碳酸盐地幔岩部分熔融过程中电导率的变化,厘清碳酸盐熔体在金伯利岩岩浆形成过程中所起的作用,并探讨Slave克拉通中部Lac de Gras地区约80~120 km深处的高导成因,我们利用DS 3600 t六面顶压机和Solartron 1260阻抗/增益-相位分析仪在1.0~3.0 GPa、673~1873 K温压条件下分别测量了含碳酸钠（Na₂CO₃）、碳酸钙（CaCO₃）和大洋中脊玄武岩（MORB）的地幔岩样品的电导率.实验结果表明,地幔岩样品的电导率主要受到温度和组分的影响,而压力对其影响较小.在温度低于1023 K时,含Na₂CO₃地幔岩样品的电导率明显高于含同比重CaCO₃和MORB的;温度达到1023 K时,含Na₂CO₃地幔岩样品开始熔融;但在之后的200 K温度区间内,该部分熔融样品的电导率随温度的增加几乎不发生变化.这一现象或许揭示：地幔深部的碳酸质岩浆在快速上升过程中会同化吸收岩石圈地幔中的斜方辉石（Opx）,进而形成金伯利岩岩浆,期间岩浆的电导率几乎不发生变化.含CaCO₃和MORB的地幔岩样品分别在1723 K和1423 K开始熔融,其部分熔融样品的电导率随温度的增加而快速增加.依据前人的研究结果和我们的实验结果,我们认为可以用含碳酸盐的部分熔融样品来解释Slave克拉通中部Lac de Gras地区约80~120 km深处的异常高导现象,并推测熔体中碳酸盐的熔体比例小于2 wt.%.

     

高温高压下地幔矿物岩石电导率影响因素研究进展

实验室高温高压条件下获得的地幔矿物岩石电导率值可以帮助获得地球内部物质组成、物质运动变化状态和解释地球物理探测资料.研究表明,电导率测量影响因素(外部因素和内部因素)控制不当将使得测量的电导率值产生较大差异.本文综述了近20年来这些影响因素对地幔矿物岩石电导率的影响程度及进展情况,电导率随着温度,铁含量和水含量的增加而增加;不含水条件下,电导率随着氧逸度和压力的增加分别增加和减小,含水条件下则恰恰相反;忽略颗粒边界的影响;测量频率和结晶方向对电导率的影响尚存在一定争议;进行电导率测量时有必要考虑系统平衡时间和样品中铁含量的流失.最后探讨了高温高压条件下电导率实验研究的不足和发展方向.     

Experimental studies of electrical conductivities and P-wave velocities of gabbro at high pressures and high temperatures

The studies on the physical properties of minerals and rocks in combination with the work in petrology, mineralogy and geochemistry are not only a useful mean to look into the composition and structure of the earth抯 interior, but also can provide extreme…     

高温高压下斜长角闪岩电导率研究及其地球物理启示

中下地壳和俯冲带区域的高电导率异常（0.01~1 S·m^-1）可能与地球内部的特定物质及其变化有关.斜长角闪岩是中下地壳以及俯冲带区域的重要组成之一,高温高压下斜长角闪岩的电导率研究对认识电导率异常具有重要意义.本研究采用交流阻抗谱法,在0.5,1.0,1.5 GPa和473~1073 K条件下测量了天然斜长角闪岩样品的复阻抗,实验结果表明压力对斜长角闪岩的电导率影响非常小,而温度对于电导率影响非常显著,其电导率在1073 K可以达到10^-0.5 S·m^-1;实验获得的活化能值为52.21 kJ·mol^-1,推断其导电机制可能为小极化子传导（Fe²⁺的氧化）主导.结合本实验获得的结果与大陆岩石圈和俯冲带的温度结构,我们计算得到相应的电性结构剖面,并与三种不同构造背景下的大陆岩石圈（克拉通、大陆裂谷和活动造山带）和俯冲带区域的电磁剖面结构进行了对比研究,结果发现斜长角闪岩可以解释大陆裂谷和活动造山带构造背景下的莫霍面附近的高电导率异常现象,同时可能是导致较热的俯冲带区域（例如卡斯卡迪地区）高电导率异常现象的原因.

     

高温高压下斜长角闪岩电导率研究及其地球物理启示

中下地壳和俯冲带区域的高电导率异常（0.01~1 S·m^-1）可能与地球内部的特定物质及其变化有关.斜长角闪岩是中下地壳以及俯冲带区域的重要组成之一,高温高压下斜长角闪岩的电导率研究对认识电导率异常具有重要意义.本研究采用交流阻抗谱法,在0.5,1.0,1.5 GPa和473~1073 K条件下测量了天然斜长角闪岩样品的复阻抗,实验结果表明压力对斜长角闪岩的电导率影响非常小,而温度对于电导率影响非常显著,其电导率在1073 K可以达到10^-0.5 S·m^-1;实验获得的活化能值为52.21 kJ·mol^-1,推断其导电机制可能为小极化子传导（Fe²⁺的氧化）主导.结合本实验获得的结果与大陆岩石圈和俯冲带的温度结构,我们计算得到相应的电性结构剖面,并与三种不同构造背景下的大陆岩石圈（克拉通、大陆裂谷和活动造山带）和俯冲带区域的电磁剖面结构进行了对比研究,结果发现斜长角闪岩可以解释大陆裂谷和活动造山带构造背景下的莫霍面附近的高电导率异常现象,同时可能是导致较热的俯冲带区域（例如卡斯卡迪地区）高电导率异常现象的原因.     

Experimental studies on elastic and rheological properties of amphibolites at high pressure and high temperature

The experimental studies done at high temperature and high pressure find that increased temperature can lead to dramatic velocity and strength reductions of most of rocks at high confining pressure[1,2]. What causes this phenomenon? Is it due to dehydrati…     

大陆岩石圈流变研究进展与高温高压流变实验现状

大陆岩石圈类似于“三明治”的多层流变结构已经被广泛接受,并用于大陆动力学研究的各方面．然而近年来地震资料和高温高压流变实验结果表明,大陆岩石圈流变可能不是单一模式,流变结构具有多样性,而下地壳流变特性是其中最复杂的层次,这不仅受下地壳成分和结构本身的非均匀控制,而且与其含水程度相关．高温高压流变实验已经积累了大量的数据,但基性岩流变实验目前仍然处于数据积累阶段,缺乏系统性,特别是缺少含水基性岩的流变实验结果,因此,加强干的和含水的基性岩流变实验研究是深入认识下地壳岩石流变必不可少的手段和方法之一．     

高温高压条件下纳米材料强度的测试和分析方法

基于高温高压同步辐射X射线衍射和飞行时间中子衍射实验,我们提出了一种通过衍射研究纳米材料本征力学性能的方法.实验通过高压压缩实验对纳米晶和微米晶Ni的变形行为进行了对比研究;二者在不同压力下的晶胞体积数据表明,纳米晶Ni具有明显的弹性软化现象,体弹模量比微米晶Ni减小约10%.研究结果表明,纳米晶Ni的整体抗压缩性减小是由于该材料纳米晶壳层呈现为张应力状态,具有较低的抗压缩性,这与分子动力学模拟结果一致.基于该方法,通过定量分析衍射峰的宽化和偏移,我们可以获得晶粒之间的高应力聚集区所产生的"微观/局部"屈服,以及整个样品在应力下所产生的"宏观/整体"屈服.我们的应变/应力图形分析方法还可以研究材料的屈服强度、高温高压条件下的晶粒破碎/长大、加工硬化/软化,以及多晶体中的固有残余/表面应变.本文提出的方法可以用于岩石矿物的高温高压流变强度的定量测定,为研究岩石圈以及地幔物质的蠕变对流提供了高科技的研究手段.     

Effects of high pressure and temperature on the properties of nanocrystals in rocks: Evidences from Raman spectroscopy

A search is conducted to detect nanocrystals in a sample of apogranitic pseudotachylite, which is a product of extremely strong crushing of granite in a seismogenic fault. Raman spectroscopy revealed nanocrystals of quartz measuring approximately 17 to 25 nm and low-temperature albite ranging from 8 to 30 nm. The crystallographic cell in the nanocrystals is deformed. The internal stresses which might have been responsible for these deformations vary from approximately −300 (compression) to +480 (tension) MPa. It is found that after having been exposed to high pressure (1 GPa) and temperature (470–500°C for 10 minutes and 550–600°C for 16 minutes), the nanocrystals of quartz reduced in size to ≈10 nm, and the nanocrystals of albite, to 13 nm. At the same time, the level of tension in the lattice spacing of quartz increased.     

Multi‐depth monitoring of electrical conductivity and temperature of groundwater at a multilayered coastal aquifer: Jeju Island,Korea

To supplement conventional geophysical log data, this study presents temporal variations in electrical conductivity (EC) and temperature with depth in a multilayered coastal aquifer, on the eastern part of Jeju Island, Korea. One‐month time‐series data obtained at eight points from a multi‐depth monitoring system showed that semidiurnal and semimonthly tidal variations induced dynamic fluctuations in EC and temperature. At some depths, EC ranged from 1483 to 26 822 µS cm^?1, while some points showed no significant variations. The results of EC log and time‐series data revealed that a sharp fresh‐saltwater interface occurred at low tide, but the diffusion zone broadened to 20 m at high tide. EC, temperature, and tide level data were used for the cross‐correlation analysis. The response time of EC and temperature to tide appears to range from less than 30 min to 11 h. Using end‐member mixing analysis (EMMA), the fraction of variations of chloride concentration in the multilayered aquifer was explained, and a conceptual model was developed which subdivided the coastal aquifer into four vertical zones. The percentage of water derived from seawater varied from 2 to 48 at specific depth, owing to tidal fluctuations. Continuous observations of EC and temperature at multiple depths are powerful tools for quantifying the transport of saline water by tidal variations in multilayered coastal aquifers. Copyright © 2008 John Wiley & Sons, Ltd.     

高温高压下矿物岩石电导率的实验研究进展

高温高压下矿物、岩石电性性质的实验研究是了解地球内部物质成分、演化过程及进行地球物理探测资料解释的有力工具.本文主要介绍了高温高压下电导率实验在如何保持良好绝缘性能,如何消除或减小极化效应及如何减小外界电信号对测量信号的干扰等方面的技术、方法,阐述了温度、压力、氧逸度、水含量以及熔体等因素对矿物、岩石电导率的影响以及一些主要的研究结果和进展情况,讨论了电性研究的地球物理和地质意义,并指出了尚需研究的不足之处.     

Investigating plant root effects on soil electrical conductivity: An integrated field monitoring and statistical modelling approach

Plants have been shown to affect soil water content and temperature. Previous studies were conducted mainly in forestry and agricultural soils, where conditions of soil and vegetation are different from those in an urban landscape. In an urban landscape, the influence of plant roots on electrical conductivity, soil water content and temperature is still not clear. This study aims to investigate the effects of soil water content and temperature on electrical conductivity in vegetated soils through an integrated field monitoring and computational modelling approach. A new relationship between soil electrical conductivity and water content as well as temperature is proposed. Field monitoring was conducted in both vegetated (tree species) and bare soils. The monitoring included measurements of soil water content, soil temperature and soil electrical conductivity. This was followed by response surface regression modelling. Measured results show that soil temperature at shallow depths was lower in vegetated soil than that in the bare soil. This observation was also consistent with the higher soil water content and hence, higher electrical conductivity under tree canopy. The model developed could predict nonlinear relationships between electrical conductivity and soil temperature and water content. Uncertainty analysis indicated normal distribution for electrical conductivity under variation of soil temperature and water content. © 2018 John Wiley & Sons, Ltd.     

Accuracy and precision of different sampling strategies and flux integration methods for runoff water: comparisons based on measurements of the electrical conductivity

Because of their fast response to hydrological events, small catchments show strong quantitative and qualitative variations in their water runoff. Fluxes of solutes or suspended material can be estimated from water samples only if an appropriate sampling scheme is used. We used continuous in‐stream measurements of the electrical conductivity of the runoff in a small subalpine catchment (64 ha) in central Switzerland and in a very small (0·16 ha) subcatchment. Different sampling and flux integration methods were simulated for weekly water analyses. Fluxes calculated directly from grab samples are strongly biased towards high conductivities observed at low discharges. Several regressions and weighted averages have been proposed to correct for this bias. Their accuracy and precision are better, but none of these integration methods gives a consistently low bias and a low residual error. Different methods of peak sampling were also tested. Like regressions, they produce important residual errors and their bias is variable. This variability (both between methods and between catchments) does not allow one to tell a priori which sampling scheme and integration method would be more accurate. Only discharge‐proportional sampling methods were found to give essentially unbiased flux estimates. Programmed samplers with a fraction collector allow for a proportional pooling and are appropriate for short‐term studies. For long‐term monitoring or experiments, sampling at a frequency proportional to the discharge appears to be the best way to obtain accurate and precise flux estimates. Copyright © 2006 John Wiley & Sons, Ltd.