结构动力分析阻尼模型研究

提出了结构动力时程分析修正的Ｒａｙｌｅｉｇｈ阻尼模型和一个基于单元特性的阻尼参数方法,可用于合理确定复杂阻尼结构的阻尼参数,工程应用实例表明,阻尼参数的计算对时程响应计算结果的影响是十分明显的,必须在分析结构体系振动特性的基础上慎重确定阻尼参数,以避免为为放大或滤掉主要振型,造成虚假的结论。     

基于复阻尼理论的混合结构Rayleigh阻尼模型

混合结构的阻尼矩阵不满足经典阻尼条件,导致传统的模态叠加法无法适用。复阻尼理论无法适用于时域计算,其自由振动响应中存在发散现象。针对混合结构的阻尼矩阵非比例性和复阻尼理论的时域发散性,基于频域等效原则构建了求解Rayleigh阻尼系数的数学优化模型,进而得到与复阻尼理论等效的Rayleigh阻尼运动方程。算例分析表明:依据位移时程响应和结构等效阻尼比可证明Rayleigh阻尼运动方程的正确性。基于本文研究成果,等效复阻尼理论的混合结构Rayleigh阻尼运动方程可直接采用模态叠加法,结合其确定的结构等效阻尼比,为混合结构的振型分解反应谱法提供理论依据。     

正常工况下大型岸桥地震瑞利阻尼系数计算方法及试验研究

针对大型岸桥地震响应分析中不同的瑞利阻尼系数会导致计算结果存在较大偏差,基于相似模型试验数据与仿真计算结果的对比分析,并综合考虑岸桥边界约束等因素,借鉴工程中常用的瑞利阻尼系数计算方法改进了岸桥结构的阻尼系数计算方法及频率选取方式。利用仿真方法和振动台模型地震试验对比分析不同瑞利阻尼系数下岸桥结构的动力响应,结果表明：瑞利阻尼系数计算方法和频率选取对岸桥结构地震响应的影响随着地震加强而提高,当加速度峰值为0.4g、0.62g,现有的阻尼系数计算方法得到的仿真结果与试验值之间的平均误差超过20%,而采用改进后的阻尼系数计算方法,岸桥地震仿真结果与试验值误差都在10%以内。     

Damper placement optimization in a shear building model with discrete design variables: a mixed‐integer second‐order cone programming approach

Supplemental damping is known as an efficient and practical means to improve seismic response of building structures. Presented in this paper is a mixed‐integer programming approach to find the optimal placement of supplemental dampers in a given shear building model. The damping coefficients of dampers are treated as discrete design variables. It is shown that a minimization problem of the sum of the transfer function amplitudes of the interstory drifts can be formulated as a mixed‐integer second‐order cone programming problem. The global optimal solution of the optimization problem is then found by using a solver based on a branch‐and‐cut algorithm. Two numerical examples in literature are solved with discrete design variables. In one of these examples, the proposed method finds a better solution than an existing method in literature developed for the continuous optimal damper placement problem. Copyright © 2013 John Wiley & Sons, Ltd.     

Damping estimation of high-rise buildings considering structural modal directions

One widespread problem in damping estimation of high-rise buildings is the neglect of structural modal directions, which may induce beating in measured dynamic responses along building geometric axes and thereby induce errors in damping estimations to some extent. Based on a proposed two degrees of freedom (2-DOF) simulation model, the effects of neglecting the modal directions on damping estimate are systematically investigated. The results show that the angular differences between the modal directions and the building geometric axes, as well as the frequency difference between the involved modes, both have significant effects on the damping estimate of high-rise buildings. This paper proposes a spectral method to determine the modal directions of high-rise buildings and further validate this method by an analysis of full-scale measurements from four skyscrapers. The damping ratios estimated based on the responses along the identified modal directions are more accurate than those based on those measured along the building geometric axes. Furthermore, an empirical prediction model for damping ratio of high-rise buildings with heights over 200 m is proposed based on the field measured damping results of several buildings with consideration of the modal directions. The objective of this study is to improve the accuracy of damping estimation of high-rise buildings and therefore provide useful information for the structural design of future skyscrapers.     

Elemental damping formulation: an alternative modelling of inherent damping in nonlinear dynamic analysis

To date, nonlinear dynamic analysis for seismic engineering predominantly employs the classical Rayleigh damping model and its variations. Though earlier studies have identified issues with the use of this model in nonlinear seismic analysis, it still remains the popular choice for engineers as well as for software providers. In this paper a new approach to modelling damping is initiated by formulating the damping matrix at an elemental level. To this regard, two new elemental level discrete damping models adapted from their global counterparts are proposed for its application in nonlinear dynamic analysis. Implementation schemes for these newly proposed models using Newmark incremental method and revised Newmark total equilibrium method is outlined. The performance of these proposed models, compared to existing models, is illustrated by conducting nonlinear dynamic analyses on a four story RC frame designed to Eurocodes. The incremental dynamic analysis study presented in the paper illustrates the fact that both the proposed models seem to produce more reliable results from an engineering perspective in comparison to the global models. It is also shown that the proposed elemental damping models lead to smaller and more realistic damping moments in the plastic hinges. Furthermore, these models could be easily included in existing software frameworks without adding noticeably to the computational effort. The computation time required for these models is approximately equivalent to the one required when using the tangent Rayleigh damping matrix with constant coefficients.     

Seismic structural control using semi-active tuned mass dampers

This paper focuses on how to determine the instantaneous damping of the semi-active tuned mass damper (SATMD) with continuously variable damping. An off-and-towards-equilibrium (OTE) algorithm is employed to examine the control performance of the structure/SATMD system by considering the damping as an assumptive control action. The damping modification of the SATMD is carried out according to the proposed OTE algorithm, which is formulated based on analysis of the structural movement under external excitations, and the measured responses of the structure at every time instant. As examples two numerical simulations of a five-storey and a ten-storey shear structures with a SATMD on the roof are conducted. The effectiveness on vibration reduction of MDOF systems subjected to seismic excitations is discussed. Analysis results show that the behavior of the structure with a SATMD is significantly improved and the feasibility of applying the OTE algorithm to the structural control design of SATMD is also verified.     

Initial versus tangent stiffness‐based Rayleigh damping in inelastic time history seismic analyses

In the inelastic time history analyses of structures in seismic motion, part of the seismic energy that is imparted to the structure is absorbed by the inelastic structural model, and Rayleigh damping is commonly used in practice as an additional energy dissipation source. It has been acknowledged that Rayleigh damping models lack physical consistency and that, in turn, it must be carefully used to avoid encountering unintended consequences as the appearance of artificial damping. There are concerns raised by the mass proportional part of Rayleigh damping, but they are not considered in this paper. As far as the stiffness proportional part of Rayleigh damping is concerned, either the initial structural stiffness or the updated tangent stiffness can be used. The objective of this paper is to provide a comprehensive comparison of these two types of Rayleigh damping models so that a practitioner (i) can objectively choose the type of Rayleigh damping model that best fits her/his needs and (ii) is provided with useful analytical tools to design Rayleigh damping model with good control on the damping ratios throughout inelastic analysis. To that end, a review of the literature dedicated to Rayleigh damping within these last two decades is first presented; then, practical tools to control the modal damping ratios throughout the time history analysis are developed; a simple example is finally used to illustrate the differences resulting from the use of either initial or tangent stiffness‐based Rayleigh damping model. Copyright © 2013 John Wiley & Sons, Ltd.     

A note on classical damping matrices

An alternative damping matrix that leads to classical normal modes and that depends explicitly on a set of prescribed modal damping ratios is presented. The alternative damping matrix can be thought of as a factorized Caughey series that allows for a simple explicit solution for the coefficients of the series and thus avoids the need to solve a potentially ill‐conditioned system of algebraic equations. The relation between the proposed damping matrix and Rayleigh, Caughey and modal damping matrices is examined. Copyright © 2008 John Wiley & Sons, Ltd.     

Evaluation of the half‐power bandwidth method to estimate damping in systems without real modes

The objective of this work was to assess the significance of the values of damping obtained applying the half‐power bandwidth method to the frequency response records of the steady‐state response of a system that does not possess real modes either because the damping matrix does not satisfy the orthogonality condition or because its parameters are functions of frequency. A multi‐degree of freedom system with real modes and different types of damping is considered first. A two degree of freedom system with an arbitrary damping matrix, a rigid mass on an elastic foundation subjected to vertical and coupled horizontal/rocking vibrations, and a single degree of freedom model of a building accounting for inertial soil structure interaction effects are considered next in more detail. The results show that the predictions of the method, when applicable compare very well with those provided by approximate formulae and procedures used in practice. Copyright © 2010 John Wiley & Sons, Ltd.     

Evaluation of Rayleigh damping and its influence on engineering demand parameter estimates

The effects of Rayleigh damping model on the engineering demand parameters of two steel moment‐resisting frame buildings were evaluated. Two‐dimensional models of the buildings were created and response history analysis were conducted for three different hazard levels. The response history analysis results indicate that mass‐proportional damping leads to high damping forces compared with restoring forces and may lead to overestimation of floor acceleration demands for both buildings. Stiffness‐proportional damping, on the other hand, is observed to suppress the higher‐mode effects in the nine‐story building resulting in lower story drift demands in the upper floors compared with other damping models. Rayleigh damping models, which combine mass‐proportional and stiffness‐proportional components, that are anchored at reduced modal frequencies lead to reasonable damping forces and floor acceleration demands for both buildings and does not suppress higher‐mode effects in the nine‐story building. Copyright © 2012 John Wiley & Sons, Ltd.     

Rayleigh波场的数值模拟及其应用

本文总结了Rayleigh波场数值模拟的4种思路和各自特点,根据Lamb问题的理论分析成果提出了基于地表激振的Rayleigh波场数值模拟技术,论述了地表集中震源作用下引起地表波动场的特点及主要影响因素。在此基础上,利用Plaxis 2D有限元软件实现了Rayleigh波场的数值模拟,并结合算例验证了所提方法的可行性和结果的合理性。最后,针对多层建筑结构,研究了不同地震动输入模式下结构动力反应的特点。结果表明,Rayleigh波作用下结构的动力反应特性明显区别于在底部输入剪切波时的结果,不同地震动输入模式对结构的振动形态和破坏模式有着明显的影响。     

黏滞阻尼器用于层间位移角超限的既有建筑的优化研究

在水平地震作用下,结构产生较大的层间变形或者结构底部地震剪力较大导致了很多建筑发生破坏.对于既有建筑,可采用安装黏滞阻尼器的加固方法减小其层间位移角,而结构层间位移角和基底剪力等均受阻尼器的位置与参数影响.因此,阻尼器的位置及参数优化的研究有重要意义.对于层间位移角超过现行规范限值的既有建筑结构,文中综合考虑结构变形与...     

Damped resonant appendages to increase inherent damping in buildings

It is demonstrated that the addition of a tuned mass-spring-dashpot system with a relatively small mass and a high damping ratio can be an effective way to increase the inherent damping characteristics of buildings and reduce, thus, their response to earthquake excitations. The demonstration is based on a theoretical formulation and on numerical and experimental studies that confirm this formulation. In the theoretical formulation, it is shown first that, if certain conditions are satisfied, the damping ratios in two of the modes of the system that is formed by a building and an appendage in resonance are approximately equal to the average of the corresponding damping ratios of the building and the appendage. Based on this finding, it is then shown that an attached appendage with a high damping ratio and tuned to the fundamental frequency of a building may increase the damping ratio in the fundamental mode of the building to a value close to half the damping ratio of the appendage. In the numerical study, the response of a ten-storey shear building is analysed under two different earthquake ground motions with and without the proposed resonant appendages. Appendages with damping ratios of 20 and 30 per cent are considered. In this study, it is found that under one of the ground motions the maximum displacement of the building's roof is reduced 30 per cent with the appendage with 20 per cent damping and 39 per cent with the one with 30 per cent damping. Similarly, with these two appendages the building's base shear is reduced 31 and 41 per cent, respectively. In the experimental study, a wooden three-storey structural model is tested in a shaking table with and without an appendage designed and constructed to have a damping ratio of 53-5 per cent. The test is conducted under random and sinusoidal base excitations. In the shaking table test under random excitation, the attached appendage reduces the response of the model 38-6 per cent, while in that under sinusoidal vibration 45-2 per cent.     

瑞利波勘探中“之”形频散曲线的形成机理及反演研究

对瑞利波勘探中“之”字形频散曲线形成的物理机理进行了理论分析,研究了诸波模的传播特性及相互关系．指出在地表下存在具有水平界面的软弱夹层和地层裂缝时,瑞利波频散曲线中的“之”字形结构是低速夹层或地层裂缝中出现多模现象的结果．利用阻尼最小二乘法和遗传算法对瑞利波频散曲线反演介质参数进行了研究和分析,发现最小二乘法不适合瑞利波“之”字形反演问题研究,而用遗传算法得到了较好的结果．     

Modeling viscous damping in nonlinear response history analysis of buildings for earthquake excitation

The Rayleigh damping model, which is pervasive in nonlinear response history analysis (RHA) of buildings, is shown to develop ‘spurious’ damping forces and lead to inaccurate response results. We prove that a viscous damping matrix constructed by superposition of modal damping matrices—irrespective of the number of modes included or values assigned to modal damping ratios—completely eliminates the ‘spurious’ damping forces. This is the damping model recommended for nonlinear RHA. Replacing the stiffness‐proportional part of Rayleigh damping by the tangent stiffness matrix is shown to improve response results. However, this model is not recommended because it lacks a physical basis and has conceptual implications that are troubling: hysteresis in damping force–velocity relationship and negative damping at large displacements. Furthermore, the model conflicts with the constant‐damping model that has been the basis for fundamental concepts and accumulated experience about the inelastic response of structures. With a distributed plasticity model, the structural response is not sensitive to the damping model; even the Rayleigh damping model leads to acceptable results. This perspective on damping provides yet another reason to employ the superior distributed plasticity models in nonlinear RHA. OpenSees software has been extended to include a damping matrix defined as the superposition of modal damping matrices. Although this model leads to a full populated damping matrix, the additional computational demands are demonstrated to be minimal. Copyright © 2015 John Wiley & Sons, Ltd.     

Reliability‐based control algorithms for nonlinear hysteretic systems based on enhanced stochastic averaging of energy envelope

Current reliability‐based control techniques have been successfully applied to linear systems; however, incorporation of stochastic nonlinear behavior of systems in such control designs remains a challenge. This paper presents two reliability‐based control algorithms that minimize failure probabilities of nonlinear hysteretic systems subjected to stochastic excitations. The proposed methods include constrained reliability‐based control (CRC) and unconstrained reliability‐based control (URC) algorithms. Accurate probabilistic estimates of nonlinear system responses to stochastic excitations are derived analytically using enhanced stochastic averaging of energy envelope proposed previously by the authors. Convolving these demand estimates with capacity models yields the reliability of nonlinear systems in the control design process. The CRC design employs the first‐level and second‐level optimizations sequentially where the first‐level optimization solves the Hamilton–Jacobi–Bellman equation and the second‐level optimization searches for optimal objective function parameters to minimize the probability of failure. In the URC design, a single optimization minimizes the probability of failure by directly searching for the optimal control gain. Application of the proposed control algorithms to a building on nonlinear foundation has shown noticeable improvements in system performance under various stochastic excitations. The URC design appears to be the most optimal method as it reduced the probability of slight damage to 8.7%, compared with 11.6% and 19.2% for the case of CRC and a stochastic linear quadratic regulator, respectively. Under the Kobe ground motion, the normalized peak drift displacement with respect to stochastic linear quadratic regulator is reduced to 0.78 and 0.81 for the URC and CRC cases, respectively, at comparable control force levels. Copyright © 2017 John Wiley & Sons, Ltd.     

Three-dimensional dynamic soil–structure interaction analysis in the time domain

A new numerical procedure is proposed for the analysis of three-dimensional dynamic soil–structure interaction in the time domain. In this study, the soil is modelled as a linear elastic solid, however, the methods developed can be adapted to include the effects of soil non-linearities and hysteretic damping in the soil. A substructure method, in which the unbounded soil is modelled by the scaled boundary finite-element method, is used and the structure is modelled by 8–21 variable-number-node three-dimensional isoparametric or subparametric hexahedral curvilinear elements. Approximations in both time and space, which lead to efficient schemes for calculation of the acceleration unit-impulse response matrix, are proposed for the scaled boundary finite-element method resulting in significant reduction in computational effort with little loss of accuracy. The approximations also lead to a very efficient scheme for evaluation of convolution integrals in the calculation of soil–structure interaction forces. The approximations proposed in this paper are also applicable to the boundary element method. These approximations result in an improvement over current methods. A three-dimensional Dynamic Soil–Structure Interaction Analysis program (DSSIA-3D) is developed, and seismic excitations (S-waves, P-waves, and surface waves) and externally applied transient loadings can be considered in analysis. The computer program developed can be used in the analysis of three-dimensional dynamic soil–structure interaction as well as in the analysis of wave scattering and diffraction by three-dimensional surface irregularities. The scattering and diffraction of seismic waves (P-, S-, and Rayleigh waves) by various three-dimensional surface irregularities are studied in detail, and the numerical results obtained are in good agreement with those given by other authors. Numerical studies show that the new procedure is suitable and very efficient for problems which involve low frequencies of interest for earthquake engineering. Copyright © 1999 John Wiley & Sons Ltd     

Damping‐adjusted combination rule for the response spectrum analysis of base‐isolated buildings

The classical response spectrum method continues to be the most popular approach for designing base‐isolated buildings, therefore avoiding computationally expensive nonlinear time‐history analyses. In this framework, a new method for the seismic analysis and design of building structures with base isolation system (BIS) is formulated and numerically validated, which enables one to overcome the main shortcomings of existing techniques based on the response spectrum method. The main advantages are the following: first, reduced computational effort with respect to an exact complex‐valued modal analysis, which is obtained through a transformation of coordinates in two stages, both involving real‐valued eigenproblems; second, effective representation of the damping, which is pursued by consistently defining different viscous damping ratios for the modes of vibration of the coupled BIS‐superstructure dynamic system; and third, ease of use, because a convenient reinterpretation of the combination coefficients leads to a novel damping‐adjusted combination rule, in which just a single response spectrum is required for the reference value of the viscous damping ratio. The proposed approach is specifically intended for design situations where (i) the dynamic behaviour of seismic isolators can be linearised and (ii) effects of nonproportional damping, as measured by modal coupling indexes, are negligible in the BIS‐superstructure assembly. Copyright © 2012 John Wiley & Sons, Ltd.     

A METHOD OF ESTIMATING THE PARAMETERS OF TUNED MASS DAMPERS FOR SEISMIC APPLICATIONS

The optimum parameters of tuned mass dampers (TMD) that result in considerable reduction in the response of structures to seismic loading are presented. The criterion used to obtain the optimum parameters is to select, for a given mass ratio, the frequency (tuning) and damping ratios that would result in equal and large modal damping in the first two modes of vibration. The parameters are used to compute the response of several single and multi-degree-of-freedom structures with TMDs to different earthquake excitations. The results indicate that the use of the proposed parameters reduces the displacement and acceleration responses significantly. The method can also be used in vibration control of tall buildings using the so-called ‘mega-substructure configuration’, where substructures serve as vibration absorbers for the main structure. It is shown that by selecting the optimum TMD parameters as proposed in this paper, significant reduction in the response of tall buildings can be achieved. © 1997 John Wiley & Sons, Ltd.