低周反复荷载下Q460钢材框架柱抗震性能分析

为了进一步完善Q460钢材在抗震设计规范中相关限值的要求,本文利用有限元软件ABAQUS,以轴压比、翼缘宽厚比、腹板高厚比和壁板宽厚比为变量,建立了共48根“工”字型框架柱和“箱”型框架柱,分析了其抗震性能。结果表明:翼缘宽厚比对框架柱的能量耗散系数影响较小;能量耗散系数随轴压比、腹板高厚比（“工”字型）和壁板宽厚比（“箱”型）增大而明显减小;框架柱的极限承载力随轴压比的减小及壁板宽厚比和翼缘宽厚比的增大而逐渐增大,当腹板高厚比接近规范限值时,承载力下降趋势明显增大。与采用Q235钢材的框架柱相比,Q460钢材框架柱的延性较小,仅为2左右;当采用Q460钢材时,“工”字型框架柱的极限位移角限值建议取为0.03,“箱”型框架柱的极限位移角限值建议取为0.032。规范中对翼缘宽厚比限值的规定偏于保守,其值最大可取至9。无论是“工”字型框架柱还是“箱”型框架柱,其腹板高厚比均不宜过大。Q460钢材框架柱的刚度退化率随轴压比的增大而增强,且翼缘宽厚比越大,腹板高厚比越小,柱的初始刚度越大,刚度退化程度越明显。     

Recent progress of seismic research on tall buildings in China Mainland

To study the seismic behavior of high strength concrete fi lled double-tube(CFDT) columns,each consisting of an external square steel tube and an internal circular steel tube,quasi-static tests on eight CFDT column specimens were conducted.The test variables included the width-to-thickness ratio(β1) and the area ratio(β2) of the square steel tube,the wall thickness of the circular steel tube,and the axial force(or the axial force ratio) applied to the CFDT columns.The test results indicate that for CFDT columns with a square steel tube with β1 of 50.1 and 24.5,local buckling of the specimen was found at a drift ratio of 1/150 and 1/50,respectively.The lateral force-displacement hysteretic loops of all specimens were plump and stable.Reducing the width-to-thickness ratio of the square steel tube,increasing its area ratio,or increasing the wall thickness of the internal circular steel tube,led to an increased fl exural strength and deformation capacity of the specimens.Increasing the design value of the axial force ratio from 0.8 to 1.0 may increase the fl exural strength of the specimens,while it may also decrease the ultimate deformation capacity of the specimen with β1 of 50.1.     

应用OpenSees计算双钢管高强砼柱的水平力—位移滞回曲线

应用OpenSees计算外方内圆复合钢管高强混凝土柱（简称双钢管高强混凝土柱）的水平力—位移滞回曲线。分析了双钢管高强混凝土柱的单元和截面纤维划分。钢管材料采用双线性模型Steel02,混凝土模型采用Concrete02,圆钢管内和钢管之间的混凝土采用Susantha模型,考虑钢管对混凝土的约束作用,计算得到的水平力—位移滞回曲线与试验结果符合较好。在此基础上,应用OpenSees对双钢管高强混凝土柱进行参数影响分析,讨论了轴压比、方钢管壁厚（宽厚比）、径宽比、径厚比对双钢管高强混凝土柱抗震性能的影响。结果表明：增大轴压比,延性降低;增大方钢管壁厚（减小宽厚比）,水平承载力增大;增大圆钢管直径和壁厚,有助于提高双钢管高强混凝土柱的竖向和水平承载力能力,增大耗能能力。     

高轴压比下圆钢管钢渣混凝土柱抗震性能试验研究

通过2根圆钢管普通混凝土柱与5根圆钢管钢渣混凝土柱在高轴压比下的水平低周反复加载试验,研究圆钢管钢渣混凝土柱的轴压比、钢管壁厚、钢渣砂替代率和长细比对其破坏形态、滞回耗能能力、骨架曲线、延性及耗能、刚度退化的影响规律。研究结果表明:钢渣混凝土试件破坏过程和破坏形态与普通混凝土试件基本相同,主要表现为钢管底部鼓曲的压弯破坏;所有试件滞回曲线饱满,无明显“捏缩”现象;高轴压比试件存在明显承载力突降现象,合理的径厚比（钢管直径/钢管壁厚）对高轴压比试件承载力突降有明显改善作用;低轴压比试件延性系数大于4.0,高轴压比试件延性系数介于1.57～3.76之间,轴压比增大,试件延性下降;试件破坏时等效粘滞阻尼系数ξ_eq介于0.259～0.437之间;建议采用《钢管混凝土混合结构技术标准》（GB/T51446－2021）或《钢管混凝土结构技术规程》（DBJ/T13－51－2010）计算地震作用下钢管钢渣混凝土柱压弯承载力,但高轴压比钢管钢渣混凝土柱计算结果需乘以折减系数0.8。     

Seismic performance of recycled concrete-filled square steel tube columns

An experimental study on the seismic performance of recycled concrete-filled square steel tube (RCFST) columns is carried out. Six specimens were designed and tested under constant axial compression and cyclic lateral loading. Two parameters, replacement percentage of recycled coarse aggregate (RCA) and axial compression level, were considered in the test. Based on the experimental data, the hysteretic loops, skeleton curves, ductility, energy dissipation capacity and stiffness degradation of RCFST columns were analyzed. The test results indicate that the failure modes of RCFST columns are the local buckling of the steel tube at the bottom of the columns, and the hysteretic loops are full and their shapes are similar to normal CFST columns. Furthermore, the ductility coefficient of all specimens are close to 3.0, and the equivalent viscous damping coefficient corresponding to the ultimate lateral load ranges from 0.323 to 0.360, which demonstrates that RCFST columns exhibit remarkable seismic performance.     

Seismic behavior and strength capacity of steel tube‐reinforced concrete composite columns

The steel tube‐reinforced concrete (ST‐RC) composite column is a novel type of composite column, which consists of a steel tube embedded in RC. In this paper, the seismic behavior of ST‐RC columns is examined through a series of experiments in which 10 one‐third scale column specimens were subjected to axial forces and lateral cyclic loading. The test variables include the axial force ratio applied to the columns and the amount of transverse reinforcement. All specimens failed in a flexural mode, showing stable hysteresis loops. Thanks to the steel tube and the high‐strength concrete it is filled with, the ST‐RC column specimens had approximately 30% lower axial force ratios and 22% higher maximum bending moments relative to the comparable RC columns when subjected to identical axial compressive loads. The amount of transverse reinforcement made only a small difference to the lateral load‐carrying capacity but significantly affected the deformation and energy dissipation capacity of the ST‐RC columns. The specimens that satisfied the requirements for transverse reinforcement adopted for medium ductile RC columns as specified by the Chinese Code for Seismic Design of Buildings (GB 50011‐2010) and EuroCode 8 achieved an ultimate drift ratio of around 0.03 and a displacement ductility ratio of approximately 5. The design formulas used to evaluate the strength capacity of the ST‐RC columns were developed on the basis of the superposition method. The predictions from the formulas showed good agreement with the test results, with errors no greater than 10%. Copyright © 2013 John Wiley & Sons, Ltd.     

Seismic vulnerability evaluation of axially loaded steel built-up laced members Ⅱ: evaluations

The test results described in Part 1 of this paper (Lee and Bruneau, 2008) on twelve steel built-up laced members(BLMs) subjected to quasi-static loading are analyzed to provide better knowledge on their seismic behavior. Strengthcapacity of the BLM specimens is correlated with the strength predicted by the AISC LRFD Specifications. Assessmentsof hysteretic properties such as ductility capacity, energy dissipation capacity, and strength degradation after buckling of thespecimen are performed. The compressive strength of BLMs is found to be relatively well predicted by the AISC LRFDSpecifications. BLMs with smaller kl/r were ductile but failed to reach the target ductility of 3.0 before starting to fracture,while those with larger kl/r could meet the ductility demand in most cases. The normalized energy dissipation ratio, ECETand the normalized compressive strength degradation, Cr"/Cr of BLMs typically decrease as normalized displacements δ/δbexpincrease, and the ratios for specimens with larger kl/r dropped more rapidly than for specimens with smaller kl/r; similartrends were observed for the monolithic braces. The BLMs with a smaller slenderness ratio, kl/r, and width-to-thickness ratio,b/t, experienced a larger number of inelastic cycles than those with larger ratios.     

高强钢筋混凝土短肢剪力墙抗震性能试验研究

通过对采用高强钢筋的6片T形混凝土短肢剪力墙和采用高强钢筋高强混凝土的6片L形短肢剪力墙进行低周往复加载试验,研究了T形和L形的破坏形态与性能差异,分析了高厚比、轴压比、配箍间距等参数对构件破坏形态、滞回耗能、骨架曲线、延性及耗能等抗震性能的影响,对比分析了构件与普通短肢剪力墙的抗震性能差异。试验结果表明:采用腹板端部箍筋加密的方式可减轻构件端部的损伤和降低正负向加载时承载力和延性的不对称性;T形构件中高厚比为5的试件表现为弯曲破坏,其他构件表现为弯剪破坏;试验中高厚比小的构件相对于高厚比大的试件延性耗能更好,轴压比增大,构件承载力提高但延性降低;与普通短肢剪力墙相比,T形短肢剪力墙承载力和变形能力提高,耗能增加,L形短肢剪力墙承载力提高较大,极限位移增大,构件后期变形能力略有降低,但可以满足抗震性能要求。     

Hysteretic behavior of special shaped columns composed of steel and reinforced concrete (SRC)

This paper describes a series of experimental investigations on seventeen specimens of steel reinforced concrete special shaped(SRCSS) columns under low cyclic reversed loading using parallel crosshead equipment. Nine T-shaped SRC columns, four L-shaped SRC columns and four +-shaped SRC columns were tested to examine the effects of shape steel confi guration, loading angle, axial compressive ratio and shear-span ratio on the behavior(strength, stiffness, energy dissipation, ductility, etc.) of SRCSS column specimens. The failure modes and hysteretic performance of all the specimens were obtained in the tests. Test results demonstrate that the shear-span ratio is the main parameter affecting the failure modes of SRCSS columns. The specimens with small shear-span ratio are prone to shear failure, and the primary failure planes in SRCSS columns are parallel to the loading direction. As a result, there is a symmetry between positive and negative loading directions in the hysteretic curves of the SRCSS columns. The majority of displacement ductility coeffi cients for all the specimens are over 3.0, so that the SRCSS columns demonstrate a better deformation capacity. In addition, the equivalent viscous damping coeffi cients of all the specimens are greater than 0.2, indicating that the seismic behavior of SRCSS columns is adequate. Finally, the superposition theory was used to calculate the limits of axial compressive ratio for the specimens, and it is found that the test axial compressive ratio is close to or smaller than the calculated axial compressive ratio limit.     

Experimental study on seismic behavior of circular RC columns strengthened with pre-stressed FRP strips

Bonding fiber reinforced polymer （FRP） has been commonly used to improve the seismic behavior of circular reinforced concrete （RC） columns in engineering practice. However, FRP jackets have a significant stress hysteresis effect in this strengthening method, and pre-tensioning the FRP can overcome this problem. This paper presents test results of 25 circular RC columns strengthened with pre-stressed FRP strips under low cyclic loading. The pre-stressing of the FRP strips, types of FRP strips and longitudinal reinforcement, axial load ratio, pre-damage degree and surface treatments of the specimens are considered as the primary factors in the tests. According to the failure modes and hysteresis curves of the specimens, these factors are analyzed to investigate their effect on bearing capacity, ductility, hysteretic behavior, energy dissipation capacity and other important seismic behaviors. The results show that the initial lateral confined stress provided by pre-stressed FRP strips can effectively inhibit the emergence and development of diagonal shear cracks, and change the failure modes of specimens from brittle shear failure to bending or bending-shear failure with better ductility. As a result, the bearing capacity, ductility, energy dissipation capacity and deformation capacity of the strengthened specimens are all significantly improved.     

底部加强型多腔钢管混凝土巨型柱抗震性能试验研究

为适应巨型框架结构发展,提出了一种底部加强型多腔钢管混凝土巨型柱。为了比较它与相应普通多腔钢管混凝土巨型柱抗震性能的差异,进行了6个1/25缩尺的巨型柱模型在轴向压力或轴向拉力下的低周反复荷载试验研究。6个模型中:按底部截面构造区分,3个试件为底部加强型巨型柱模型,3个试件为相应普通巨型柱模型;按轴力作用方向区分,4个试件为轴压试件,轴压比分别为0.5、0.25,2个试件为轴拉试件,轴拉比为0.2。比较分析了各试件的承载力、刚度及其退化过程、延性、滞回特性、耗能和破坏特征。研究表明:底部加强型巨型柱与普通巨型柱相比,承载力、延性、耗能能力明显提高,刚度退化速度减慢,工作性能较稳定;轴压试件与轴拉试件相比,轴压试件抗震性能相对较好。     

高强钢筋高延性纤维增强混凝土框架结构的屈服机制和抗震性能

为了对混凝土框架结构的地震破坏机制和抗震性能进行控制,在框架柱中配置高强钢筋,并将纤维增强混凝土(FRC)用于框架结构的预期损伤部位。结构柱中的高强钢筋用来减小结构的残余变形,FRC材料用来增加结构的耗能能力和损伤容限。设计了三个框架,采用动力弹塑性时程分析方法进行分析。研究结果表明,采用高强钢筋提高了结构的整体承载能力,在层间侧移角达到3%之前避免了柱铰的出现(包括底层柱底),并且减小了结构的残余变形;预期损伤部位采用FRC材料能够提高结构的塑性耗能。     

腹板开孔形状影响耗能支撑滞回性能试验研究

腹板开孔耗能支撑有效地避免了传统中心支撑斜杆的失稳破坏,具有较强的耗能能力.为研究腹板开孔形状对支撑滞回性能的影响,对腹板开菱形孔、椭圆孔及长圆孔耗能支撑试件进行了低周往复加载试验,分析了试件在循环荷载作用下的破坏机理、滞回性能、承载能力、刚度退化及耗能能力.试验结果表明:耗能支撑试件滞回曲线饱满,耗能性能优越.耗能支...     

A study on using wide‐flange section web under out‐of‐plane flexure for passive energy dissipation

It is not common to purposely subject the web of wide‐flange or I‐sections to out‐of‐plane bending. However, yielding the web under this loading condition can be a stable source of energy dissipation as the transition at the corner from the web to the flanges is smooth and weld‐free; this prevents stress concentrations causing premature failure and eliminates uncertainties and imperfections associated with welding. Further, short segments of wide‐flange or I‐sections constitute a simple and inexpensive energy dissipating device as minimum manufacturing is required and leftovers not useful for other structural purposes can be re‐utilized. This paper proposes a new type of seismic damper in the form of braces based on yielding the web of short length segments of wide‐flange or I‐shaped steel sections under out‐of‐plane bending. The hysteretic behavior and ultimate energy dissipation capacity is investigated via component tests under cyclic loads. The experimental results indicate that the damping device has stable restoring force characteristics and a high energy dissipation capacity. Based on these results, a simple hysteretic model for predicting the load–displacement curve of the seismic damper is proposed, along with a procedure for predicting its ultimate energy dissipation capacity and anticipating its failure under arbitrarily applied cyclic loads. The procedure considers the influence of the loading path on the ultimate energy dissipation capacity. Finally, shaking table tests on half‐scale structures are conducted to further verify the feasibility and effectiveness of the new damper, and to assess the accuracy of the hysteretic model and the procedure for predicting its failure. Copyright © 2010 John Wiley & Sons, Ltd.     

T形配钢钢骨混凝土柱抗震性能数值分析

为研究非对称配钢钢骨混凝土柱的抗震性能,基于12根T形配钢钢骨混凝土柱的拟静力试验研究进行非线性数值模拟,了解其破坏机制、承载力、延性及耗能能力,探讨轴压比、配钢率、剪跨比对抗震性能的影响。结果表明,低周反复荷载作用下T形配钢钢骨混凝土柱滞回曲线饱满,具有良好的延性和耗能能力。在峰值荷载前,数值模拟结果与试验结果吻合较好。轴压力在一定范围内提高了试件承载力,但降低了延性;增大配钢率能提高试件的承载力、刚度和延性,使得峰值荷载后试件的性能退化趋于平缓;剪跨比对试件破坏形态有显著影响,随剪跨比的增大试件延性性能提高。     

Research on seismic behavior and shear strength of SRHC frame columns

The seismic behavior of steel reinforced high strength and high performance concrete(SRHC)frame columns was investigated through pseudo-static experiments of 16 frame columns with various shear span ratios,axial compression ratios,concrete strengths,steel ratios and stirrup ratios.Three kinds of failure mechanisms are presented and the characteristics of experimental hysteretic curves and skeleton curves with different design parameters are discussed.The columns’ductility and energy dissipation were quantitatively evaluated based on seismic resistance.The research results indicate that SRHC frame columns can withstand extreme bearing capacity,but the abilities of ductility and energy dissipation are inferior because of SRHC’s natural brittleness.As a result,the axial load ratio should be restricted and some construction measures adopted,such as increasing the stirrup ratio.This research established effect factors on the bearing capacity of SPHC columns.Finally,an algorithm for obtaining ultimate bearing capacity using the flexural failure mode is established based on a modified planesection assumption.The authors also established equations to determine shearing baroclinic failure and shear bond failure based on the accumulation of the axial load force distribution ratio.The calculated results of shear bearing capacity for different failure modes were in good agreement with the experimental results.     

免拆超高性能混凝土模板钢筋混凝土柱抗震性能研究

为研究预制超高性能混凝土(UHPC)模板钢筋混凝土(RC)柱的抗震性能,并验证预制UHPC模板在往复荷载作用下是否发生剥离,考虑轴压比、剪跨比、箍筋间距和保护层厚度,设计制作6根免拆模板柱(PTC)和1根RC对比柱试件,对其进行拟静力试验,研究其破坏形态、滞回性能、变形和耗能能力以及强度和刚度退化规律等。结果表明,与加载方向垂直的预制UHPC模板大约在PTC试件峰值荷载的70%时发生剥离,与加载方向平行的预制UHPC模板在试件最终破坏时剥离;在剪跨比、轴压比和箍筋数量均分别相同的条件下,由UHPC模板加10 mm混凝土作为保护层的试件,其抗震性能相对较好,但其承载力和前期刚度略有减小。     

基于OpenSees的RCS组合框架结构抗震性能模拟分析

选取已有钢筋混凝土柱—钢梁组合结构（RCS）框架的低周期反复试验数据,采用地震工程开源模拟软件OpenSees对其进行有限元模拟,对比骨架曲线与滞回曲线,试验结果与有限元结果吻合较好。随后考察弯矩放大系数（Mc/Mb=0.86、1.48、2.04）、柱轴压比（n=0.06、0.2、0.3、0.6、0.8）对抗震性能的影响,得到了各参数下框架的滞回曲线、骨架曲线和各特征阶段的荷载与位移值。分析了框架的破化过程、延性与强度退化。结果表明：RCS组合框架滞回曲线饱满,具有良好的变形及耗能能力;随着弯矩放大系数的减小、柱轴压比的增大,框架的水平极限承载力降低、屈服状态提前、位移延性降低。分析结果可供有关研究或工程应用参考。     

Seismic performance of steel reinforced ultra high-strength concrete composite frame joints

To investigate the seismic performance of a composite frame comprised of steel reinforced ultra high-strength concrete (SRUHSC) columns and steel reinforced concrete (SRC) beams, six interior frame joint specimens were designed and tested under low cyclically lateral load. The effects of the axial load ratio and volumetric stirrup ratio were studied on the characteristics of the frame joint performance including crack pattern, failure mode, ductility, energy dissipation capacity, strength degradation and rigidity degradation. It was found that all joint specimens behaved in a ductile manner with flexural-shear failure in the joint core region while plastic hinges appeared at the beam ends. The ductility and energy absorption capacity of joints increased as the axial load ratio decreased and the volumetric stirrup ratio increased. The displacement ductility coefficient and equivalent damping coefficient of the joints fell between the corresponding coefficients of the steel reinforced concrete (SRC) frame joint and RC frame joint. The axial load ratio and volumetric stirrup ratio have less influence on the strength degradation and more influence on the stiffness degradation. The stiffness of the joint degrades more significantly for a low volumetric stirrup ratio and high axial load ratio. The characteristics obtained from the SRUHSC composite frame joint specimens with better seismic performance may be a useful reference in future engineering applications.     

循环荷载特征对焊接工字形钢支撑低周疲劳性能的影响

通过14根铰支焊接工字形支撑在不同特征的循环轴向位移荷载下的低周疲劳试验，研究了循环轴向位移荷载的位移幅值、平均位移幅值及加载次序等因素对钢支撑低周疲劳及耗能性能的影响。研究发现，对称循环荷载中幅值越小，支撑翼缘局部屈曲发展越晚，其耗能及承载力退化也越平缓。文中提出了支撑在幅值6δ≤Δδ≤12δy的对称循环荷载下的疲劳寿命经验公式。试验表明，循环荷载的位移幅值是支撑疲劳损伤及耗能退化的最主要影响因素，过载峰效应及适当的平均压位移幅值改善了钢支撑低周疲劳及耗能性能。