高轴压比下圆钢管钢渣混凝土柱抗震性能试验研究

通过2根圆钢管普通混凝土柱与5根圆钢管钢渣混凝土柱在高轴压比下的水平低周反复加载试验,研究圆钢管钢渣混凝土柱的轴压比、钢管壁厚、钢渣砂替代率和长细比对其破坏形态、滞回耗能能力、骨架曲线、延性及耗能、刚度退化的影响规律。研究结果表明:钢渣混凝土试件破坏过程和破坏形态与普通混凝土试件基本相同,主要表现为钢管底部鼓曲的压弯破坏;所有试件滞回曲线饱满,无明显“捏缩”现象;高轴压比试件存在明显承载力突降现象,合理的径厚比（钢管直径/钢管壁厚）对高轴压比试件承载力突降有明显改善作用;低轴压比试件延性系数大于4.0,高轴压比试件延性系数介于1.57～3.76之间,轴压比增大,试件延性下降;试件破坏时等效粘滞阻尼系数ξ_eq介于0.259～0.437之间;建议采用《钢管混凝土混合结构技术标准》（GB/T51446－2021）或《钢管混凝土结构技术规程》（DBJ/T13－51－2010）计算地震作用下钢管钢渣混凝土柱压弯承载力,但高轴压比钢管钢渣混凝土柱计算结果需乘以折减系数0.8。     

T形配钢钢骨混凝土柱抗震性能数值分析

为研究非对称配钢钢骨混凝土柱的抗震性能,基于12根T形配钢钢骨混凝土柱的拟静力试验研究进行非线性数值模拟,了解其破坏机制、承载力、延性及耗能能力,探讨轴压比、配钢率、剪跨比对抗震性能的影响。结果表明,低周反复荷载作用下T形配钢钢骨混凝土柱滞回曲线饱满,具有良好的延性和耗能能力。在峰值荷载前,数值模拟结果与试验结果吻合较好。轴压力在一定范围内提高了试件承载力,但降低了延性;增大配钢率能提高试件的承载力、刚度和延性,使得峰值荷载后试件的性能退化趋于平缓;剪跨比对试件破坏形态有显著影响,随剪跨比的增大试件延性性能提高。     

钢管混凝土桥墩抗震性能试验研究

为研究钢管混凝土桥墩的抗震性能,对钢管混凝土桥墩和钢筋混凝土桥墩进行了拟静力对比试验研究。根据试件的破坏发展过程以及各试件的滞回曲线和骨架曲线,分析了其滞回性能、耗能能力、延性、强度退化及刚度退化等抗震性能。试验结果表明,钢管混凝土桥墩的抗震性能明显好于钢筋混凝土桥墩。在含钢率和轴力相同的情况下,钢管混凝土桥墩的滞回曲线比钢筋混凝土桥墩丰满得多,前者的耗能能力约为后者的4.46倍,钢管混凝土桥墩的延性大于钢筋混凝土桥墩;随着轴压比的增大,钢管混凝土桥墩延性有所下降,强度退化加快,但对其刚度退化的影响不大。     

Design of transverse reinforcement to avoid premature buckling of main bars

This paper proposes an enhancement to the current strength and confinement‐based design of transverse reinforcement in rectangular and circular reinforced concrete members to ensure that the flexural strength of reinforced concrete sections does not degrade excessively due to buckling of longitudinal bars until the desired level of plastic deformation is achieved. Antibuckling design criteria are developed based on a popular bar buckling model that uses a bar buckling parameter (combining the bar diameter, yield strength, and buckling length) to solely describe the bar buckling behavior. The value of buckling parameter that limits the buckling‐induced stress loss to 15% in compression bars at the strain corresponding to the design ductility is determined. For a bar of known diameter and yield strength, the maximum allowable buckling length can then be determined, which serves as the maximum limit for the tie/stirrup/hoop spacing. Lateral stiffness required to restrain the buckling tendency of main bars at the locations of the ties/stirrups/hoops depends on the flexural rigidity of the main bars and the buckling length (equal to or multiple of tie/hoop/stirrup spacing), whereas the antibuckling stiffness (ie, resistance) provided by the ties/stirrups/hoops depends on their size, number, and arrangement. Using the above concept, design recommendations for the amount, arrangement, and spacing of rectangular and circular ties/stirrups/hoops are then established to ensure that the antibuckling stiffness of the provided transverse reinforcement is greater than the stiffness required to restrain the buckling‐prone main bars. Key aspects of the developed method are verified using experimental tests from literature.     

Research on seismic behavior and shear strength of SRHC frame columns

The seismic behavior of steel reinforced high strength and high performance concrete(SRHC)frame columns was investigated through pseudo-static experiments of 16 frame columns with various shear span ratios,axial compression ratios,concrete strengths,steel ratios and stirrup ratios.Three kinds of failure mechanisms are presented and the characteristics of experimental hysteretic curves and skeleton curves with different design parameters are discussed.The columns’ductility and energy dissipation were quantitatively evaluated based on seismic resistance.The research results indicate that SRHC frame columns can withstand extreme bearing capacity,but the abilities of ductility and energy dissipation are inferior because of SRHC’s natural brittleness.As a result,the axial load ratio should be restricted and some construction measures adopted,such as increasing the stirrup ratio.This research established effect factors on the bearing capacity of SPHC columns.Finally,an algorithm for obtaining ultimate bearing capacity using the flexural failure mode is established based on a modified planesection assumption.The authors also established equations to determine shearing baroclinic failure and shear bond failure based on the accumulation of the axial load force distribution ratio.The calculated results of shear bearing capacity for different failure modes were in good agreement with the experimental results.     

型钢连接装配式低矮剪力墙抗震性能试验研究

采用带锚筋的锚板、腹板、端板以及加劲板作为连接件,能够通过干式连接方法将上下预制剪力墙构件连为整体。为研究该新型全装配式剪力墙的受力性能和抗震性能,设计了2个剪跨比为0.783的试件和1个相同剪跨比及配筋率的现浇整体墙体,并进行了低周往复拟静力试验,分析了该全装配式剪力墙的承载能力、刚度、延性性能和耗能能力等。研究结果表明:现浇整体墙体和全装配式剪力墙的破坏形式均为受剪破坏,全装配式剪力墙的极限位移角大于现浇整体墙体极限位移角,分别为1/77和1/133,轴压比为0.3时平均延性系数3.47,低于现浇整体墙体平均延性系数4.62;但该全装配式剪力墙具有较高的承载能力和耗能能力。型钢与剪力墙的锚筋需采用穿孔塞焊的形式连接,避免锚筋与锚板焊接的位置发生剪断的现象。     

Effect of seismic design details on hysteresis performance of SRC-RC transfer columns

Four types of seismic design details were tested using 11 transfer column specimens and one comparison specimen of RC under low cyclic reversed loading. Test results show that diagonal cracks control the failure pattern and damage occurs mainly in the RC section with weak shear capacity in the transfer columns. There is a large difference in the bearing capacity and ductility of the transfer columns according to the test results, which indicates that the strengthening effect of diverse structural measures is quite different. The section ratio of I-section-encased steel and the axial compression ratio also have a great influence on the bearing capacity and ductility. Although the bearing capacity of transfer columns with additional longitudinal bars and additional X bars is relatively large, they have poor deformation capacity. Setting more stirrups along the columns is the best structural measure to enhance the seismic performance. The studs on the I-sectionencased steel by welding can help to complete the stress transfer between the steel and concrete, and avoid performance degradation of the two materials due to bonding failure.     

低周反复荷载下Q460钢材框架柱抗震性能分析

为了进一步完善Q460钢材在抗震设计规范中相关限值的要求,本文利用有限元软件ABAQUS,以轴压比、翼缘宽厚比、腹板高厚比和壁板宽厚比为变量,建立了共48根“工”字型框架柱和“箱”型框架柱,分析了其抗震性能。结果表明:翼缘宽厚比对框架柱的能量耗散系数影响较小;能量耗散系数随轴压比、腹板高厚比（“工”字型）和壁板宽厚比（“箱”型）增大而明显减小;框架柱的极限承载力随轴压比的减小及壁板宽厚比和翼缘宽厚比的增大而逐渐增大,当腹板高厚比接近规范限值时,承载力下降趋势明显增大。与采用Q235钢材的框架柱相比,Q460钢材框架柱的延性较小,仅为2左右;当采用Q460钢材时,“工”字型框架柱的极限位移角限值建议取为0.03,“箱”型框架柱的极限位移角限值建议取为0.032。规范中对翼缘宽厚比限值的规定偏于保守,其值最大可取至9。无论是“工”字型框架柱还是“箱”型框架柱,其腹板高厚比均不宜过大。Q460钢材框架柱的刚度退化率随轴压比的增大而增强,且翼缘宽厚比越大,腹板高厚比越小,柱的初始刚度越大,刚度退化程度越明显。     

大跨度钢管混凝土拱桥抗震性能指标研究

高轴压比钢管混凝土墩柱的试验结果对钢管混凝土拱肋具有较大的借鉴意义。为明确大跨度钢管混凝土拱桥的抗震性能指标,研究了高轴比钢管混凝土构件的破坏过程及延性性能。以弯矩作为性能指标将高轴压比钢管混凝土构件的试验破坏过程分为轻微损伤、有限损伤与严重损伤3个阶段,结合钢管混凝土截面性能状态的数值分析,探讨了高轴压比钢管混凝土构件的破坏机理。结果表明:高轴压比钢管混凝土构件具有一定的可用延性;提出了以计算等效屈服弯矩作为抗震性能指标,适当利用延性和实现钢管混凝土拱桥的有限损伤抗震设计,并给出了与有限损伤相关的截面性能状态及参数。研究成果弥补了规范在此方面的不足,可供高烈度地震区大跨度钢管混凝土拱桥抗震设计时参考。     

地震作用下预应力混凝土管桩运动响应三维数值分析

基于黏弹性人工边界,建立上部结构-桩-土的共同作用三维有限元模型,分析地震作用下预应力混凝土管桩的运动响应特性。分别针对预应力混凝土管桩的桩径、双层软硬土剪切波速比值、上覆土层厚度、上部结构荷载等影响因素进行数值计算。参数分析表明:在地震作用下,桩径的增大会导致桩身整体弯矩相应增加,特别是桩身土层分界面处增大明显;软硬土层剪切波速比及上覆土层厚度的增加,引起土层分界面处桩身峰值弯矩增加;固定桩头条件下,桩头与桩身软硬土层分界面处均会产生较大的运动弯矩;上部结构的惯性荷载对固定桩头的内力有着较大影响,对桩身深处段弯矩影响较小。本文研究结论可为预应力混凝土管桩抗震设计提供有益的理论参考。     

L形高强钢筋高强混凝土短肢剪力墙抗震性能试验研究

L形短肢剪力墙由于其肢短的特点,已经广泛应用于民用建筑的外围结构。为研究使用高性能材料加强后的新型L形短肢剪力墙的抗震性能,本文基于不同轴压比、高宽比和配箍率,设计制作了六片短肢剪力墙试验模型,对其进行了低周往复荷载试验,根据试验结果,对试件的滞回性能、刚度退化、破坏形态、耗能能力等抗震性能指标进行分析与研究。结果表明:高强材料的使用提高了试件的整体承载能力;在满足最小配箍率的前提下适当增大配箍率有利于提高试件的承载力和延性;轴压比大小是影响试件破坏形态的主要因素,随着轴压比逐渐增大,试件趋于脆性破坏;高厚比大小是影响试件抗震性能的次要因素,其影响程度主要根据工程实际情况来确定,但可以肯定的是,较大高厚比有利于提升墙体的稳定性和承载能力。     

薄壁方钢管混凝土柱劲化设计及轴压性能探讨

对于薄壁方形钢管混凝土柱,有效且经济地提高柱的承载力、刚度和延性,增强其抵抗局部屈曲的能力是目前的一项重要研究课题。据此,进行8个薄壁方形钢管混凝土轴压试件的研究,比较普通薄壁钢管混凝土柱与劲化薄壁钢管混凝土柱的轴压极限承载力、延性性能、局部屈曲模态及相应耗钢量,研究表明:劲化设置在增加较少用钢量的情况下,使钢管壁对核心混凝土的约束作用相对于普通钢管混凝土柱和单纯加设约束拉杆的钢管混凝土柱更趋均匀,提高了整体约束效应,混凝土强度得以提高,本构关系明显改善。从而增加了钢管混凝土柱的轴压承载力和延性,改变了钢管的局部屈曲变形状态,其实用效益与经济效益极其可观,具有良好推广价值。     

Seismic performance of steel reinforced ultra high-strength concrete composite frame joints

To investigate the seismic performance of a composite frame comprised of steel reinforced ultra high-strength concrete (SRUHSC) columns and steel reinforced concrete (SRC) beams, six interior frame joint specimens were designed and tested under low cyclically lateral load. The effects of the axial load ratio and volumetric stirrup ratio were studied on the characteristics of the frame joint performance including crack pattern, failure mode, ductility, energy dissipation capacity, strength degradation and rigidity degradation. It was found that all joint specimens behaved in a ductile manner with flexural-shear failure in the joint core region while plastic hinges appeared at the beam ends. The ductility and energy absorption capacity of joints increased as the axial load ratio decreased and the volumetric stirrup ratio increased. The displacement ductility coefficient and equivalent damping coefficient of the joints fell between the corresponding coefficients of the steel reinforced concrete (SRC) frame joint and RC frame joint. The axial load ratio and volumetric stirrup ratio have less influence on the strength degradation and more influence on the stiffness degradation. The stiffness of the joint degrades more significantly for a low volumetric stirrup ratio and high axial load ratio. The characteristics obtained from the SRUHSC composite frame joint specimens with better seismic performance may be a useful reference in future engineering applications.     

The effect of axial inertia on the bending eigenfrequencies of a timoshenko two-bar frame

The equations of free lateral vibrations of a uniform Timoshenko two-bar frame including the effects of axial motion and joint mass with its rotational inertia are presented. The influence on the flexural eigenfrequencies of the axial motion alone or in combination with other parameters is fully assessed and thoroughly discussed. These parameters are: the translational and rotational inertia of the joint mass, the transverse shear deformation and rotatory inertia, the length, stiffness and slenderness ratios of the two bars of the frame. The variety of numerical results presented herein leads to the important finding that for framed structures the effect of axial inertia on the flexural eigenfrequencies alone or in combination with the foregoing parameters may be considerable. In particular, if the joint mass should be accounted for, the foregoing effect cannot be ignored, since it leads, in general, to considerable errors even for frames with relatively slender bars.     

钢筋混凝土空心桥墩的振动台试验研究

为研究空心桥墩的抗震性能及影响参数,对9个不同配筋率、配箍率和轴压比的试件进行振动台试验。研究了不同性能量化参数对破坏现象、加速度响应、动力放大系数、延性和耗能等的影响。结果表明:轴压比和配筋率较小时,裂缝开展较多且位置距墩底相对偏高。增大配筋率,加速度响应、动力放大系数和位移延性系数增大,耗能减小;轴压比的影响与配筋率相反。增大配箍率,加速度响应和动力放大系数减小,位移延性系数和试件耗能增大。可为矩形空心桥墩的抗震设计提供参考。     

高强钢筋混凝土短肢剪力墙抗震性能试验研究

通过对采用高强钢筋的6片T形混凝土短肢剪力墙和采用高强钢筋高强混凝土的6片L形短肢剪力墙进行低周往复加载试验,研究了T形和L形的破坏形态与性能差异,分析了高厚比、轴压比、配箍间距等参数对构件破坏形态、滞回耗能、骨架曲线、延性及耗能等抗震性能的影响,对比分析了构件与普通短肢剪力墙的抗震性能差异。试验结果表明:采用腹板端部箍筋加密的方式可减轻构件端部的损伤和降低正负向加载时承载力和延性的不对称性;T形构件中高厚比为5的试件表现为弯曲破坏,其他构件表现为弯剪破坏;试验中高厚比小的构件相对于高厚比大的试件延性耗能更好,轴压比增大,构件承载力提高但延性降低;与普通短肢剪力墙相比,T形短肢剪力墙承载力和变形能力提高,耗能增加,L形短肢剪力墙承载力提高较大,极限位移增大,构件后期变形能力略有降低,但可以满足抗震性能要求。     

机械连接预应力实心方桩承台节点抗震性能试验研究

预应力管桩在高烈度抗震设防地区已禁用,而普通钢筋混凝土方桩成本较高。首先针对卡扣式机械连接预应力混凝土实心方桩、PHC管桩和普通钢筋混凝土方桩与承台处的节点进行拟静力试验,并利用试验数据针对Park-Ang损伤模型进行了修正,进行了损伤指数分析。研究结果表明:预应力方桩比普通钢筋混凝土方桩的抗裂性能明显好,而预应力混凝土实心方桩承台节点耗能能力和延性低于预应力管桩和普通钢筋混凝土方桩;截桩施工导致桩端部损失部分预应力,相比较未截桩试件屈服荷载和极限荷载均减小,节点裂缝开展较早,损伤较未截桩试件严重;增配普通钢筋试件的滞回曲线比较饱满,水平承载能力和位移延性得到提升,节点抗震性能得到提升与改善;预应力混凝土实心方桩损伤前期较小,而一旦发生损伤后,损伤指数发展较快。     

Experimental study of hollow rectangular bridge column performance under vertical and cyclically bilateral loads

To investigate the seismic performance of hollow reinforced concrete(RC) bridge columns of rectangular cross section under constant axial load and cyclically biaxial bending,five specimens were tested.A parametric study is carried out for different axial load ratios,longitudinal reinforcement ratios and lateral reinforcement ratios.The experimental results showed that all tested specimens failed in the flexural failure mode and their ultimate performance was dominated by flexural capacity,which is represented by the rupture/buckling of tensile longitudinal rebars at the bottom of the bridge columns.Biaxial force and displacement hysteresis loops showed significant stiffness and strength degradations,and the pinching effect and coupling interaction effect of both directions severely decrease the structural seismic resistance.However,the measured ductility coefficient varying from 3.5 to 5.7 and the equivalent viscous damping ratio varying from 0.19 and 0.26 can meet the requirements of the seismic design.The hollow RC rectangular bridge columns with configurations of lateral reinforcement in this study have excellent performance under bidirectional earthquake excitations,and may be considered as a substitute for current hollow RC rectangular section configurations described in the Guideline for Seismic Design of Highway Bridges(JTG/T B02-01-2008).The length of the plastic hinge region was found to approach one sixth of the hollow RC rectangular bridge column height for all specimen columns,and it was much less than those specified in the current JTG/T.Thus,the length of the plastic hinge region is more concentrated for RC rectangular hollow bridge columns.     

设计参数对高层装配式钢结构建筑抗倒塌能力的影响

以某高层装配式钢结构建筑为研究对象,研究设计参数对其抗倒塌能力的影响,通过ABAQUS有限元软件,对装配式混凝土平面框架的低周反复加载试验进行模拟。结果表明,增大框架柱轴压比可提高结构承载力,在荷载峰值达到后会有较快的降低,显著降低了延性。在荷载低周反复作用下,结构延性、承载力、耗能等随着梁柱线刚度比的降低,抗震指标全部呈现增加趋势。随着梁柱线刚度比的增大,层间位移角沿楼层分布均匀性变得越来越差;由于受到荷载作用低周反复后,会大大增加混凝土的强度,并降低耗能和延性指标,同时结构承载力则略微增大。增大轴压比后,如果保持相同的地震动强度,则将会大大提高结构性能极限状态的可能性,而如果结构的轴压比较大,很可能会出现对地震响应性能水平产生破坏等问题。     

钢板混凝土联肢剪力墙抗震性能试验研究

以轴压比和钢连梁弯剪比为主要参数,设计并制作了3个1/4缩尺的钢板混凝土联肢剪力墙子结构,对试件施加恒定轴压力和水平往复加载.观察了各试件破坏特征,对比了顶层水平荷载-侧移曲线和骨架曲线以及延性系数和等效黏滞阻尼系数等抗震性能指标.结果表明:高轴压比会使整个试件的延性变差;弯剪比越大试件耗能能力越好,弯剪比越小试件刚度...