Off‐Mount Calibration and One New Potential Pyrrhotite Reference Material for Sulfur Isotope Measurement by Secondary Ion Mass Spectrometry

Sulfur isotope measurements in three sulfide (two pyrite and one pyrrhotite) samples on two epoxy mounts showed that the mount‐to‐mount variation of raw δ³⁴S values was negligible when secondary ion mass spectrometry (SIMS) analytical settings remained stable. In consequence, an off‐mount calibration procedure for SIMS sulfur isotope analysis was applied in this study. YP136 is a pyrrhotite sample collected from northern Finland. Examination of thin sections with a polarising microscope, backscattered electron image analyses and wavelength dispersive spectrometry mapping showed that the sample grains display no internal growth or other zoning. A total of 318 sulfur isotope (spot) measurements conducted on more than 100 randomly selected grains yielded highly consistent sulfur isotope ratios. The repeatability of all the analytical results of ³⁴S/³²S was 0.3‰ (2s, n = 318), which is the same as that of the well‐characterised pyrite reference materials PPP‐1 and UWPy‐1. Its δ³⁴S value determined by gas mass spectrometry was 1.5 ± 0.1‰ (2s, n = 11), which agrees with the SIMS data (1.5 ± 0.3‰, 2s) calibrated by pyrrhotite reference material Po‐10. Therefore, YP136 pyrrhotite is considered a candidate reference material for in situ sulfur isotope determination.     

Biotite Reference Materials for Secondary Ion Mass Spectrometry 18O/16O Measurements

Five new biotite reference materials were calibrated at the SwissSIMS laboratory (University of Lausanne) for oxygen isotope determination by secondary ion mass spectrometry (SIMS) and are available to the scientific community. The oxygen isotope composition of the biotites, UNIL_B1 to B5, was determined by laser‐heating fluorination to be 11.4 ± 0.11‰, 8.6 ± 0.15‰, 6.1 ± 0.04‰, 7.1 ± 0.05‰ and 7.6 ± 0.04‰, respectively. SIMS analyses on spots smaller than 20 μm gave a measurement repeatability of 0.3‰ (2 standard deviation, 2s). The matrix effect due to solid solution in natural biotite could be expressed as a linear function of X_Mg and X_F for biotite. No effect was found for different crystallographic orientations. SIMS analysis allows the oxygen isotope composition of biotite to be measured with a measurement uncertainty of 0.3–0.4‰ (2s) for biotites with similar major element compositions. A measurement uncertainty of 0.5‰ (2s) is realistic when F poor biotites (lower than 0.2% m/m oxides) within the compositional range of X_Mg of 0.3–0.9 were compared from different sessions. The linear correlation with F content offers a reasonable working curve for F‐rich biotites, but additional reference materials are needed to confirm the model.     

Development and Re‐Evaluation of Tourmaline Reference Materials for In Situ Measurement of Boron δ Values by Secondary Ion Mass Spectrometry

Six tourmaline samples were investigated as potential reference materials (RMs) for boron isotope measurement by secondary ion mass spectrometry (SIMS). The tourmaline samples are chemically homogeneous and cover a compositional range of tourmaline supergroup minerals (primarily Fe, Mg and Li end‐members). Additionally, they have homogeneous boron delta values with intermediate precision values during SIMS analyses of less than 0.6‰ (2s). These samples were compared with four established tourmaline RMs, that is, schorl IAEA‐B‐4 and three Harvard tourmalines (schorl HS#112566, dravite HS#108796 and elbaite HS#98144). They were re‐evaluated for their major element and boron delta values using the same measurement procedure as the new tourmaline samples investigated. A discrepancy of about 1.5‰ in δ¹¹B was found between the previously published reference values for established RMs and the values determined in this study. Significant instrumental mass fractionation (IMF) of up to 8‰ in δ¹¹B was observed for schorl–dravite–elbaite solid solutions during SIMS analysis. Using the new reference values determined in this study, the IMF of the ten tourmaline samples can be modelled by a linear combination of the chemical parameters FeO + MnO, SiO₂ and F. The new tourmaline RMs, together with the four established RMs, extend the boron isotope analysis of tourmaline towards the Mg‐ and Al‐rich compositional range. Consequently, the in situ boron isotope ratio of many natural tourmalines can now be determined with an uncertainty of less than 0.8‰ (2s).     

Analytical Developments in Secondary Ion Mass Spectrometry 2003

This annual review of secondary ion mass spectrometry (SIMS) highlights significant progress in the application of the technology for the following areas: U-Pb geochronology (notably in the fields of reference material zircons), sources of uncertainty during analysis and secondary ion yields. Major publications introduced a new zircon reference sample and dealt with an intercomparison study of a suite of established calibrators, some of which have been shown to have certain limitations. Another publication claimed that the principal uncertainty in U-Pb dating is related to variations in the Pb and U relative emission yields over a complete analytical session. 2003 saw the introduction of an automated particle identification procedure applied to the analysis of a chondritic meteorite, as well as new geometries of SIMS hardware (NanoSIMS) and techniques (time-of-flight SIMS). NanoSIMS allows a two to three order of magnitude reduction in sampling volume as a result of a reduced beam diameter, and time-of-flight SIMS allows the study of sample surfaces, and can provide data for elements concurrently.     

‘Box‐Profile’ Ion Implants as Geochemical Reference Materials for Electron Probe Microanalysis and Secondary Ion Mass Spectrometry

Although electron probe microanalysis and secondary ion mass spectrometry are widely used analytical techniques for geochemical and mineralogical applications, metrologically rigorous quantification remains a major challenge for these methods. Secondary ion mass spectrometry (SIMS) in particular is a matrix‐sensitive method, and the use of matrix‐matched reference materials (RMs) is essential to avoid significant analytical bias. A major problem is that the number of available RMs for SIMS is extremely small compared with the needs of analysts. One approach for the production of matrix‐specific RMs is the use of high‐energy ion implantation that introduces a known amount of a selected isotope into a material. We chose the more elaborate way of implanting a so‐called ‘box‐profile’ to generate a quasi‐homogeneous concentration of the implanted isotope in three dimensions, which allows RMs not only to be used for ion beam analysis but also makes them suitable for EPMA. For proof of concept, we used the thoroughly studied mineralogically and chemically ‘simple’ SiO₂ system. We implanted either ⁴⁷Ti or ⁴⁸Ti into synthetic, ultra‐high‐purity silica glass. Several ‘box‐profiles’ with mass fractions between 10 and 1000 μg g^?1 Ti and maximum depths of homogeneous Ti distribution between 200 nm and 3 μm were produced at the Institute of Ion Beam Physics and Materials Research of Helmholtz‐Zentrum Dresden‐Rossendorf. Multiple implantation steps using varying ion energies and ion doses were simulated with Stopping and Range of Ions in Matter (SRIM) software, optimising for the target concentrations, implantation depths and technical limits of the implanter. We characterised several implant test samples having different concentrations and maximum implantation depths by means of SIMS and other analytical techniques. The results show that the implant samples are suitable for use as reference materials for SIMS measurements. The multi‐energy ion implantation technique also appears to be a promising procedure for the production of EPMA‐suitable reference materials.     

H2O Content Measurement in Phengite by Secondary Ion Mass Spectrometry: A New Set of Reference Materials

Five new natural white mica reference materials (RMs) were developed for in situ H₂O content analyses by secondary ion mass spectrometry at the SwissSIMS laboratory of Lausanne University, Switzerland. The white mica reference materials cover a large part of the natural muscovite–phengite compositional range and are therefore suitable as reference materials for the analysis of natural rocks as well as individual minerals. The independent H₂O content of the reference materials UNIL_WM1 to UNIL_WM5 was obtained by thermal conversion elemental analyser and corresponds to 4.35 ± 0.02, 4.33 ± 0.03, 4.30 ± 0.07, 4.50 ± 0.02 and 4.42 ± 0.11 (% m/m, ± 1s), respectively. SIMS determinations of H₂O content revealed a matrix effect correlated to the FeO content of white mica. The compositional range in FeO of the reference materials that were calibrated for H₂O determination is from 1.13% to 3.67% m/m. No crystallographic orientation dependency was observed at the level of homogeneity of these reference materials. An analytical precision of 0.02% to 0.08% m/m (1SE) is expected for the final uncertainty on measurements of unknown white micas in natural samples.     

New Olivine Reference Material for In Situ Microanalysis

A new olivine reference material – MongOL Sh11‐2 – for in situ analysis has been prepared from the central portion of a large (20 × 20 × 10 cm) mantle peridotite xenolith from a ~ 0.5 My old basaltic breccia at Shavaryn‐Tsaram, Tariat region, central Mongolia. The xenolith is a fertile mantle lherzolite with minimal signs of alteration. Approximately 10 g of 0.5–2 mm gem quality olivine fragments were separated under binocular microscope and analysed by EPMA, LA‐ICP‐MS, SIMS and bulk analytical methods (ID‐ICP‐MS for Mg and Fe, XRF, ICP‐MS) for major, minor and trace elements at six institutions world‐wide. The results show that the olivine fragments are sufficiently homogeneous with respect to major (Mg, Fe, Si), minor and trace elements. Significant inhomogeneity was revealed only for phosphorus (homogeneity index of 12.4), whereas Li, Na, Al, Sc, Ti and Cr show minor inhomogeneity (homogeneity index of 1–2). The presence of some mineral and fluid‐melt micro‐inclusions may be responsible for the inconsistency in mass fractions obtained by in situ and bulk analytical methods for Al, Cu, Sr, Zr, Ga, Dy and Ho. Here we report reference and information values for twenty‐seven major, minor and trace elements.     

Accurate Trace Element Reporting in Corundum: Development of Secondary Ion Mass Spectrometry Relative Sensitivity Factors

The attractive physical and chemical properties of corundum lend to this material’s importance in both its natural and synthetic forms. However, much of the quantitative work performed on this material is plagued by unknown inaccuracy as non‐matrix‐matched reference materials are used. To conduct accurate quantitative analysis using SIMS, matrix‐specific relative sensitivity factors (RSFs) were determined for eighteen trace elements in corundum using dose‐verified ion implants. The RSF values ranged from 2.56 × 10²² to 3.29 × 10²⁴ cm^‐1 with total combined uncertainty values ranging from 7 to 10%. The RSF values, which are related to ionisation potentials, showed trends consistent with expectations for an insulating oxide. The developed values were applied to calibrate reference materials for LA‐ICP‐MS and to study other natural and synthetic corundum samples. A measurement reference material calibrated for Mg, Si, Ti, V, Fe and Ga produced consistent results over ten sessions in 4 years with relative standard deviations per trace element of 5% or less, confirming the repeatability of our process. A key finding was that calibrating LA‐ICP‐MS with NIST SRM 610 and 612 glasses to analyse corundum resulted in under‐reporting trace elements Be, Ti, V, Fe, Co, Ni and Ga compared with using matrix‐matched reference materials.     

Boron Isotope Analysis of Silicate Glass with Very Low Boron Concentrations by Secondary Ion Mass Spectrometry

We present an improved method for the determination of the boron isotopic composition of volcanic glasses with boron concentrations of as low as 0.4–2.5 μg g^?1, as is typical for mid‐ocean ridge basalt glasses. The analyses were completed by secondary ion mass spectrometry using a Cameca 1280 large‐radius ion microprobe. Transmission and stability of the instrument and analytical protocol were optimised, which led to an improvement of precision and reduction in surface contamination and analysis time compared with earlier studies. Accuracy, reproducibility (0.4–2.3‰, 2 RSD), measurement repeatability (2 RSE = 2.5–4.0‰ for a single spot with [B] = 1 μg g^?1), matrix effects (? 0.5‰ among komatiitic, dacitic and rhyolitic glass), machine drift (no internal drift; long‐term drift: ~ 0.1‰ hr^?1), contamination (~ 3–8 ng g^?1) and machine background (0.093 s^?1) were quantified and their influence on samples with low B concentrations was determined. The newly developed set‐up was capable of determining the B isotopic composition of basaltic glass with 1 μg g^?1 B with a precision and accuracy of ± 1.5‰ (2 RSE) by completing 4–5 consecutive spot analyses with a spatial resolution of 30 μm × 30 μm. Samples with slightly higher concentrations (≥ 2.5 μg g^?1) could be analysed with a precision of better than ± 2‰ (internal 2 RSE) with a single spot analysis, which took 32 min.     

Albany K-Feldspar: A New Pb Isotope Reference Material

Lead isotopes are a powerful and versatile tool to elucidate fundamental geological problems related to the formation and evolution of continental crust. K-feldspar is a popular target for Pb isotope measurement as it is prevalent in many rock types and tends to capture the initial Pb isotope composition of its parental magma. We present data for a new Pb isotope reference material: Albany K-feldspar; as well as updated data for Shap K-feldspar. Results of Pb double-spike TIMS for Albany K-feldspar are ²⁰⁶Pb/²⁰⁴Pb = 16.7872 ± 0.0062, ²⁰⁷Pb/²⁰⁴Pb = 15.5640 ± 0.0056, and ²⁰⁸Pb/²⁰⁴Pb = 36.6600 ± 0.0168 (2s). TIMS measurement results for Shap K-feldspar indicate two isotopically distinct Pb populations. LA-MC-ICP-MS, with a spatial resolution as high as 15 μm, indicates a homogeneous Pb isotopic composition in Albany K-feldspar. In accord with previous studies, our results show that scatter in the measured Pb isotope ratios, related to the low natural isotopic abundance of ²⁰⁴Pb, along with the effect of isobaric ²⁰⁴Hg-²⁰⁴Pb interference, increases at lower count rates. However, the mean Pb isotope ratios measured via LA-MC-ICP-MS using a range of spot sizes are in excellent agreement with TIMS results thus highlighting the feasibility of Pb isotope determination via LA-MC-ICP-MS to access geological information preserved in small crystals, including mineral inclusions.     

SA01 – A Proposed Zircon Reference Material for Microbeam U‐Pb Age and Hf‐O Isotopic Determination

A new natural zircon reference material SA01 is introduced for U‐Pb geochronology as well as O and Hf isotope geochemistry by microbeam techniques. The zircon megacryst is homogeneous with respect to U‐Pb, O and Hf isotopes based on a large number of measurements by laser ablation‐inductively coupled plasma‐mass spectrometry (LA‐ICP‐MS) and secondary ion mass spectrometry (SIMS). Chemical abrasion isotope dilution thermal ionisation mass spectrometry (CA‐ID‐TIMS) U‐Pb isotopic analyses produced a mean ²⁰⁶Pb/²³⁸U age of 535.08 ± 0.32 Ma (2s, n = 10). Results of SIMS and LA‐ICP‐MS analyses on individual shards are consistent with the TIMS ages within uncertainty. The δ¹⁸O value determined by laser fluorination is 6.16 ± 0.26‰ (2s, n = 14), and the mean ¹⁷⁶Hf/¹⁷⁷Hf ratio determined by solution MC‐ICP‐MS is 0.282293 ± 0.000007 (2s, n = 30), which are in good agreement with the statistical mean of microbeam analyses. The megacryst is characterised by significant localised variations in Th/U ratio (0.328–4.269) and Li isotopic ratio (?5.5 to +7.9‰); the latter makes it unsuitable as a lithium isotope reference material.     

Simultaneous In Situ Analysis of Carbon and Nitrogen Isotope Ratios in Organic Matter by Secondary Ion Mass Spectrometry

An in situ measurement method for simultaneous determination of carbon and nitrogen isotope ratios in organic matter was developed by secondary ion mass spectrometry with a spatial resolution of ~ 12 μm. Secondary ion intensities of ¹²C^?₂, ¹²C¹³C^?, ¹²C¹⁴N^? and ¹²C¹⁵N^? were simultaneously measured by three Faraday cups and one electron multiplier. Ions of ¹²C₂H^? were measured to monitor hydride interferences and to correct for mass bias. The analytical precisions of δ¹³C and δ¹⁵N values of a reference material (UWLA‐1 anthracite) were 0.16‰ and 0.56‰, respectively (2s). A negative correlation was observed between the mass bias of carbon and ¹²C₂H^?/¹²C^?₂ ratios of examined reference materials. In contrast, there was no correlation between mass bias and hydrogen concentration for nitrogen. The δ¹³C_VPDB and δ¹⁵N_Air values of twenty‐two individual globules of organic matter, found in carbonate rock of the 1878 Ma Gunflint Formation, were determined by the new procedure, ranging from ?33.8‰ to ?33.3‰ and +4.2‰ to 5.8‰, respectively. Means of δ¹³C_VPDB and δ¹⁵N_Air values, ?33.5 ± 0.25‰ and +5.2 ± 0.81‰, are consistent with reported values from bulk sample analysis within analytical precision.     

NanoSr – A New Carbonate Microanalytical Reference Material for In Situ Strontium Isotope Analysis

The in situ measurement of Sr isotopes in carbonates by MC‐ICP‐MS is limited by the availability of suitable microanalytical reference materials (RMs), which match the samples of interest. Whereas several well‐characterised carbonate reference materials for Sr mass fractions > 1000 µg g^?1 are available, there is a lack of well‐characterised carbonate microanalytical RMs with lower Sr mass fractions. Here, we present a new synthetic carbonate nanopowder RM with a Sr mass fraction of ca. 500 µg g^?1 suitable for microanalytical Sr isotope research (‘NanoSr’). NanoSr was analysed by both solution‐based and in situ techniques. Element mass fractions were determined using EPMA (Ca mass fraction), as well as laser ablation and solution ICP‐MS in different laboratories. The ⁸⁷Sr/⁸⁶Sr ratio was determined by well‐established bulk methods for Sr isotope measurements and is 0.70756 ± 0.00003 (2s). The Sr isotope microhomogeneity of the material was determined by LA‐MC‐ICP‐MS, which resulted in ⁸⁷Sr/⁸⁶Sr ratios of 0.70753 ± 0.00007 (2s) and 0.70757 ± 0.00006 (2s), respectively, in agreement with the solution data within uncertainties. Thus, this new reference material is well suited to monitor and correct microanalytical Sr isotope measurements of low‐Sr, low‐REE carbonate samples. NanoSr is available from the corresponding author.     

Tourmaline Reference Materials for the In Situ Analysis of Oxygen and Lithium Isotope Ratio Compositions

Three tourmaline reference materials sourced from the Harvard Mineralogical and Geological Museum (schorl 112566, dravite 108796 and elbaite 98144), which are already widely used for the calibration of in situ boron isotope measurements, are characterised here for their oxygen and lithium isotope compositions. Homogeneity tests by secondary ion mass spectrometry (SIMS) showed that at sub‐nanogram test portion masses, their ¹⁸O/¹⁶O and ⁷Li/⁶Li isotope ratios are constant within ± 0.27‰ and ± 2.2‰ (1s), respectively. The lithium mass fractions of the three materials vary over three orders of magnitude. SIMS homogeneity tests showed variations in ⁷Li/²⁸Si between 8% and 14% (1s), which provides a measure of the heterogeneity of the Li contents in these three materials. Here, we provide recommended values for δ¹⁸O, Δ’¹⁷O and δ⁷Li for the three Harvard tourmaline reference materials based on results from bulk mineral analyses from multiple, independent laboratories using laser‐ and stepwise fluorination gas mass spectrometry (for O), and solution multi‐collector inductively coupled plasma‐mass spectroscopy (for Li). These bulk data also allow us to assess the degree of inter‐laboratory bias that might be present in such data sets. This work also re‐evaluates the major element chemical composition of the materials by electron probe microanalysis and investigates these presence of a chemical matrix effect on SIMS instrumental mass fractionation with regard to δ¹⁸O determinations, which was found to be < 1.6‰ between these three materials. The final table presented here provides a summary of the isotope ratio values that we have determined for these three materials. Depending on their starting mass, either 128 or 512 splits have been produced of each material, assuring their availability for many years into the future.     

元素分析仪-气体同位素质谱法分析硫酸钙样品的硫同位素组成

硫酸盐硫同位素的常规分析方法是将硫酸盐转化为硫酸钡后搭配双路进样SO2法,该法易于操作、数据稳定,但样品用量大、费时费力,需要繁杂的前处理,无法满足微量分析发展方向的需求。本文以石膏为例,以元素分析仪-气体同位素质谱法(EA-IRMS)直接测定硫酸钙样品硫同位素比值,对同一样品分别采用:①硫酸钙与V2O5混合后包裹于锡杯中密封,直接进行元素分析仪-气体同位素质谱分析;②硫酸钙充分溶于去离子水中,向溶有硫酸钙样品的液体中加入沉淀试剂BaCl2,将生成的硫酸钡沉淀滤出后,用去离子水清洗2~3遍,烘干后与V2O5混合包裹于锡杯中密封再进行质谱测定。实验选取了13件δ34S值变化范围介于-20‰^+30‰之间的天然石膏样品,将获得的硫同位素比值进行对比,二者δ34SV-CDT绝对差值在0.00‰~0.24‰,表明同一样品的硫同位素比值结果在误差范围内基本一致。与常规分析方法相比,本文建立的直接在线分析时无需任何化学前处理,只需直接加入适量的V2O5,V2O5和氧气中的外部氧在瞬间燃烧的过程中替代了硫酸钙本身的氧,生成的SO2气体的氧是均一的,其硫同位素比值能代表样品的硫同位素组成,无需进行氧同位素的校正。经过验证表明,硫酸钙样品的直接在线分析是完全可行的。     

Inter‐laboratory Characterisation of Apatite Reference Materials for Chlorine Isotope Analysis

Here we report on a set of six apatite reference materials (chlorapatites MGMH#133648, TUBAF#38 and fluorapatites MGMH#128441A, TUBAF#37, 40, 50) which we have characterised for their chlorine isotope ratios; these RMs span a range of Cl mass fractions within the apatite Ca₁₀(PO₄)₆(F,Cl,OH)₂ solid solution series. Numerous apatite specimens, obtained from mineralogical collections, were initially screened for ³⁷Cl/³⁵Cl homogeneity using SIMS followed by δ³⁷Cl characterisation by gas source mass spectrometry using both dual‐inlet and continuous‐flow modes. We also report major and key trace element compositions as determined by EPMA. The repeatability of our SIMS results was better than ± 0.10‰ (1s) for the five samples with > 0.5 % m/m Cl and ± 0.19‰ (1s) for the low Cl abundance material (0.27% m/m). We also observed a small, but significant crystal orientation effect of 0.38‰ between the mean ³⁷Cl/³⁵Cl ratios measured on three oriented apatite fragments. Furthermore, the results of GS‐IRMS analyses show small but systematic offset of δ³⁷Cl_SMOC values between the three laboratories. Nonetheless, all studied samples have comparable chlorine isotope compositions, with mean 10³δ³⁷Cl_SMOC values between +0.09 and +0.42 and in all cases with 1s ≤ ± 0.25.     

GHR1 Zircon – A New Eocene Natural Reference Material for Microbeam U‐Pb Geochronology and Hf Isotopic Analysis of Zircon

We present multitechnique U‐Pb geochronology and Hf isotopic data from zircon separated from rapakivi biotite granite within the Eocene Golden Horn batholith in Washington, USA. A weighted mean of twenty‐five Th‐corrected ²⁰⁶Pb/²³⁸U zircon dates produced at two independent laboratories using chemical abrasion‐isotope dilution‐thermal ionisation mass spectrometry (CA‐ID‐TIMS) is 48.106 ± 0.023 Ma (2s analytical including tracer uncertainties, MSWD = 1.53) and is our recommended date for GHR1 zircon. Microbeam ²⁰⁶Pb/²³⁸U dates from laser ablation‐inductively coupled plasma‐mass spectrometry (LA‐ICP‐MS) and secondary ion mass spectrometry (SIMS) laboratories are reproducible and in agreement with the CA‐ID‐TIMS date to within < 1.5%. Solution multi‐collector ICP‐MS (MC‐ICP‐MS) measurements of Hf isotopes from chemically purified aliquots of GHR1 yield a mean ¹⁷⁶Hf/¹⁷⁷Hf of 0.283050 ± 17 (2s, n = 10), corresponding to a εHf₀ of +9.3. Hafnium isotopic measurements from two LA‐ICP‐MS laboratories are in agreement with the solution MC‐ICP‐MS value. The reproducibility of ²⁰⁶Pb/²³⁸U and ¹⁷⁶Hf/¹⁷⁷Hf ratios from GHR1 zircon across a variety of measurement techniques demonstrates their homogeneity in most grains. Additionally, the effectively limitless reserves of GHR1 material from an accessible exposure suggest that GHR1 can provide a useful reference material for U‐Pb geochronology of Cenozoic zircon and Hf isotopic measurements of zircon with radiogenic ¹⁷⁶Hf/¹⁷⁷Hf.     

A Common Reference Material for Cadmium Isotope Studies – NIST SRM 3108

Research into natural mass‐dependent stable isotope fractionation of cadmium has rapidly expanded in the past few years. Methodologies are diverse with MC‐ICP‐MS favoured by all but one laboratory, which uses thermal ionisation mass spectrometry (TIMS). To quantify the isotope fractionation and correct for instrumental mass bias, double‐spike techniques, sample‐calibrator bracketing or element doping has been used. However, easy comparison between data sets has been hampered by the multitude of in‐house Cd solutions used as zero‐delta reference in different laboratories. The lack of a suitable isotopic reference material for Cd is detrimental for progress in the long term. We have conducted a comprehensive round‐robin assay of NIST SRM 3108 and the Cd isotope offsets to commonly used in‐house reference materials. Here, we advocate NIST SRM 3108 both as an isotope standard and the isotopic reference point for Cd and encourage its use as ‘zero‐delta’ in future studies. The purity of NIST SRM 3108 was evaluated regarding isobaric and polyatomic molecular interferences, and the levels of Zn, Pd and Sn found were not significant. The isotope ratio ¹¹⁴Cd/¹¹⁰Cd for NIST SRM 3108 lies within ～ 10 ppm Da^?1 of best estimates for the Bulk Silicate Earth and is validated for all measurement technologies currently in use.     

Automated Analyte Separation by Ion Chromatography Using a Cobot Applied to Geological Reference Materials for Li Isotope Composition

The demand for large and reliable data sets on isotopic composition has increased in geochemistry and environmental sciences over recent years. We present an automated ion chromatographic separation method using a robotic pipetting arm, termed ‘ChemCobOne’, to reduce sample separation time. Its performance was tested for lithium isotope separation in geological reference materials using a single‐step separation with HCl (0.2 mol l^?1) and a 2 ml resin volume. This refined lithium purification method does not forfeit precision, accuracy or purity compared with manual sample processing. In addition, a δ⁷Li value for NASS‐6 of 30.99 ± 0.50‰ (2s) (95% CI = 0.14‰, n = 44) was determined and the first δ⁷Li values for the granite rock reference material GS‐N (?0.57 ± 0.25‰ (2s), 95% CI = 0.15‰, n = 15), and for the soil reference material NIST SRM 2709a (?0.37 ± 0.67‰ (2s), 95% CI = 0.15‰, n = 63) are proposed.     

Secondary Ion Mass Spectrometry Bias on Isotope Ratios in Dolomite–Ankerite,Part I: δ18O Matrix Effects

We document the development of a suite of carbonate mineral reference materials for calibrating SIMS determinations of δ¹⁸O in samples with compositions along the dolomite–ankerite solid solution series [CaMg(CO₃)₂–CaFe(CO₃)₂]. Under routine operating conditions for the analysis of carbonates for δ¹⁸O with a CAMECA IMS 1280 instrument (at WiscSIMS, University of Wisconsin‐Madison), the magnitude of instrumental bias along the dolomite–ankerite series decreased exponentially by ~ 10‰ with increasing Fe content in the dolomite structure, but appeared insensitive to minor Mn substitution [< 2.6 mol% Mn/(Ca+Mg+Fe+Mn)]. The compositional dependence of bias (i.e., the sample matrix effect) was calibrated using the Hill equation, which relates bias to the Fe# of dolomite–ankerite [i.e., molar Fe/(Mg+Fe)] for thirteen reference materials (Fe# = 0.004–0.789); for calibrations employing either 10 or 3 μm diameter spot size measurements, this yielded residual values ≤ 0.3–0.4‰ relative to CRM NBS 19 for most reference materials in the suite. Analytical precision was ± 0.3‰ (2s, standard deviations) for 10‐μm spots and ± 0.7‰ (2s) for 3‐μm spots, based on the spot‐to‐spot repeatability of a drift monitor material that ‘bracketed’ each set of ten sample‐spot analyses. Analytical uncertainty for individual sample analyses was approximated by a combination of precision and calibration residual values (propagated in quadrature), suggesting an uncertainty of ± 0.5‰ (2s) for 10‐μm spots and ± 1‰ (2s) for 3‐μm spots.