基于SAR图像速度聚束调制的海浪反演研究

本文首先对合成孔径雷达（SAR）海浪成像中的3种调制（倾斜调制、流体力学调制与速度聚束调制）的影响进行了对比分析,结果显示：速度聚束调制对SAR图像的影响最为显著。另外,由于SAR图像中固有相干斑噪声的存在,较低波数范围的噪声难以滤除或抑制,利用经典MPI方法反演海浪谱会造成低波数范围谱值偏大。基于此,本文借鉴经典MPI海浪谱反演算法,建立了基于速度聚束调制的海浪方位向斜率谱和有效波高的反演算法。通过将经典MPI方法、同极化调制法及本文算法等3种海浪反演方法所得有效波高与浮标数据进行比较,结果显示：本文方法反演得到的海浪有效波高与浮标数据获得的有效波高之间的均方误差为0.79 m,为3种方法中最小。     

基于相参X-波段海洋雷达的海表轮廓测量研究

X-波段海洋雷达测量所得海面散射单元的多普勒信息与散射单元的雷达视向速度密切相关。首先,基于符号多普勒估计方法,对X-波段雷达海面回波的多普勒频移信息进行了估计;在此基础上,应用各分辨单元回波的多普勒频移信息,建立了海浪表面轮廓的反演算法。该算法中,同时考虑了雷达入射角、方位角和雷达空间分辨率等因素对反演结果的影响。通过将反演结果与浮标测量数据相比较,发现雷达空间分辨率起到了类似低通滤波的作用,该作用对短重力波谱影响显著。同时,还应用加拿大麦克马斯特大学的IPIX雷达数据对海表轮廓进行了反演,并将反演所得有效波高、海浪周期与现场测量数据进行了比较,反演结果与现场测量结果吻合较好。     

基于X波段海洋雷达的风浪联合反演方法研究

提出了一种新的利用X波段海洋雷达联合反演海面风速与海浪谱的方法,该方法不需要额外的信息输入来反演海浪谱。通过利用风速与雷达后向散射强度的经验关系获得海表风速,然后将反演的风速输入风浪谱,通过求解该模拟风浪谱与雷达观测图像谱的约束函数的最小值来确定海浪谱。利用实验数据对反演方法进行了验证,风速、有效波高、主波周期以及主波波向反演的均方根误差分别为1.9 m/s,0.4 m,1.2 s和9.6°,证明了该方法的可行性。     

降雨条件下的导航X波段雷达海浪参数反演算法研究

X波段的电磁波受降雨影响容易产生衰减,这导致导航X波段雷达在降雨时无法用于海浪观测。本文提出了一种新的降低降雨影响的算法来反演海浪参数。首先,对X波段雷达图像做主成分分析,获得波浪变化的主成分,利用一维傅里叶变换得到波数谱,对其滤波减小降雨对雷达图像的影响;然后,选取JONSWAP(Joint North Sea Wave Project)谱作为理论谱,建立以观测谱与理论谱的最小化差异为目标函数的模型,求解该模型估算海浪的有效波高。与浮标测量的有效波高相比,该方法反演的有效波高的均方根误差是0.23 m,证明了该方法的可行性。     

X-波段雷达近海海浪频谱反演的神经网络模型

X-波段雷达作为国内海浪观测的一种新工具,在海浪频谱获取和有效波高反演方面仍存在较多问题.本文利用非线性回归方法,将现场实测浮标数据频谱和雷达一维图像谱分别与标准频谱模型进行拟合,发现浮标频谱和一维图像谱具有标准频谱的特征,能够较准确地获取相应的谱参数.提出了建立由雷达一维图像谱参数反演海浪频谱参数的神经网络模型,同时在模型中加入影像序列信噪比,进而反演有效波高,并将反演结果与现场实测数据和传统算法(建立影像序列信噪比与有效波高之间的线性回归方程)进行了对比,结果表明,获取谱参数的误差和反演有效波高的平均误差在20％以内,而传统算法计算有效波高平均误差在20％以上.     

基于深度卷积神经网络的稀疏反褶积方法

本文提出一个由数据驱动的深度卷积神经网络(DCNN)模型用于求解地震反射信号的稀疏反褶积问题。反褶积是一个不适定的反问题,正则化迭代方法是求解此类问题的主要方法,但是正则化迭代方法存在正则化参数选取困难,反演结果不精确等问题。为此,本文提出DCNN方法求解地震反射信号的稀疏反褶积问题,经过训练的DCNN模型无需再次设置参数即可用于求解稀疏反褶积问题,计算速度快,结果精度高。所提DCNN模型还采用多分辨率分解和残差学习等技术以提高网络的表达能力。最后通过数值实验,并与迭代收缩阈值算法(ISTA)算法对比,使用模拟地震数据和实际地震数据验证了DCNN方法求解稀疏反褶积问题的有效性。     

波谱仪调制功率谱估计算法性能的仿真研究

基于星载波谱仪海浪方向谱探测原理,仿真了不同海况、风速下的海浪波谱仪接收信号,并采用周期图法、Welch法、AR模型法以及最小方差法共4种不同的调制谱估计方法反演出海浪谱,比较各种调制谱估计方法的海浪方向谱反演性能。仿真结果表明:对于一定方位向下的一维海浪谱反演,不同调制谱估计方法反演海浪谱性能优劣没有绝对的顺序。对于二维海浪谱反演,在成长中海浪条件下周期图法反演性能最差,其他3种方法的反演性能没有绝对优劣顺序;对于成熟风浪,最小方差法在积分能量误差、有效波高误差两个指标上的反演性能最好,在主波波向、主波波长误差上,周期图法反演性能最差,其他3种方法没有绝对优劣顺序。在涌浪条件下,AR模型法反演性能优于其他3种方法。在不同海况下,随着波谱仪中心入射角的下降,反演性能会下降。基于这些仿真结果,本文推荐最小方差法作为充分成长海浪的海浪方向谱反演的调制谱估计方法,AR模型法作为涌浪海浪方向谱反演的调制谱估计方法。     

弱流场调制下的海面微波散射模拟研究

根据海面微波散射的多尺度模型以及波流相互作用理论,对一维弱流场调制下的海面微波散射截面进行了数值模拟。结果表明,利用数值方法直接求解波作用量方程获得的海浪调制谱并结合多尺度模型可以较好地模拟弱流场引起的雷达散射截面的变化。内波等海洋现象调制了海浪谱,使得雷达散射截面反映出这些海洋特征,整个调制过程的模拟对于分析这些海洋现象并更好地利用其雷达数据具有重要意义。     

海浪成长状态对TOPEX/Poseidon高度计风速反演的影响

以墨西哥湾同步高度计、浮标资料为例,研究了海浪成长状态对高度计风速反演的影响。同步的高度计风速和浮标风速比较显示,在墨西哥湾地区,海浪成长状态对高度计风速反演有较大影响。在考虑海浪成长状态影响的条件下,利用谱模型反演高度计风速,取得了较好的效果。与目前TOPEX/Poseidon高度计风速反演业务化算法相比,在海浪未充分成长条件下,考虑海浪成长状态影响后,根据谱模型反演获得的风速与浮标风速之间的均方根误差减小了30%,平均误差减小了83%。在利用谱模型算法反演高度计风速时,谱模型中的波龄因子(表示海浪成长状态)可以根据高度计测得的有效波高和风速获得,因此该方法具有广泛的适用性。     

OSMAR-S100便携式高频地波雷达海浪和海面风探测性能分析

OSMAR-S系列便携式高频地波雷达系统采用单极子/交叉环紧凑型天线阵,通过单站雷达即可实现有效探测距离约10km内海浪和海面风的单点观测。为了更好地了解OSMAR-S100雷达系统海浪和海面风的综合探测性能,于2013年1月29日至3月7日在台湾海峡西南部海域进行了雷达与浮标观测的对比试验,得到了有效波高、有效波周期、平均风速和平均风向数据。对比结果表明,OSMAR-S100便携式高频地波雷达可有效观测距雷达10km以内有效波高0.5m以上的海浪平均状况和平均风速5m/s以上的海面风,雷达反演有效波高和有效波周期的均方根误差分别为0.60m和1.60s,反演平均风速和平均风向的均方根误差为1.83m/s和16.7°。在未经区域化标定的情况下,此结果说明了该型雷达产品已初步具备了海浪和海面风的业务化观测水平。     

Microbial Biomass and Organic Nutrients in the Deep-Sea Sediments of the Central Indian Ocean Basin

In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification

An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm.     

Phylogenetic diversity and phenotypic characterization of cultivable bacterioplankton isolated from polar oceans

A set of 27 marine planktonic bacteria isolated from the polar regions was characterized by 16S rDNA sequencing and physiological and biochemical testing. More than half of these bacteria were positive for caseinase, gelatinase and 13-glucosidase, and could utilize glucose, maltose or malic acid as carbon source for cell growth. Twelve isolates expressed nitrate reduction activities. Except for one antarctic isolate BSwlO175 belonging to Actinobacteria phylum, these isolates were classified as γ-Proteobacteria, suggesting that γ-Proteobacteria dominated in cultivable marine bacterioplankton at both poles. Genus Pseudoalteromonas was the predominant group in the Chukchi Sea and the Bering Sea, and genus ShewaneUa dominated in cultivable bacterioplankton in the Prydz Bay. With sequence similarities above 97%, genus Psychrobacter was found at both poles. These 27 isolates were psychrotolerant, and significant 16S rDNA sequence similarities were found not only between arctic and antarctic marine bacteria （ 〉 99% ）, but also between polar marine bacteria and bacteria from other aquatic environments （ ≥ 98.8% ）, including temperate ocean, deep sea, pond and lake, suggesting that in the polar oceans less temperature-sensitive bacteria may be cosmopolitan and have a bipolar, even global, distribution at the species level.     

Deep-Sea Sediment Compression Curves: Some Controlling Factors, Spurious Overconsolidation, Predictions, and Geophysical Reproduction

Oedometer tests have been carried out on 70 undisturbed surficial clays (at approximately 250 mm below the mudline), mostly collected by free-fall corers from sites widely scattered throughout the deep-sea North Atlantic. Acoustic measurements were also made, initially on contiguous samples and ultimately on the same sample using a geophysically instrumented oedometer which also collected electrical resistivity data. Apart from those quiescent areas below the carbonate compensation depth, such as north of the West Indies where very fine clays exist, most of the samples are silty clays whose geotechnical-geophysical properties are dependent on the type of clay minerals present (and their ability to take in moisture), the sand-size fraction, and the quantity of carbonate present. Thus the pure clays have high compressibilities which decrease on the addition of coarse particles, while the converse is true for the acoustic parameters, these increasing with the sand fraction. Using the notion of the intrinsic compression line for all samples, and comparison to it of the measured compression curves, it is clear that, contrary to some previously held ideas, most deep-sea clays are normally consolidated; the addition of carbonate has the effect of creating an open, stronger sediment skeleton. Interestingly, where information is available, the variation with depth of a sample's acoustic velocity follows the void ratio pressure relationship of the compression curve. This allows the construction of an in-situ sediment compression curve using the in-situ geophysical observations.     

INFORMATION FOR AUTHORS

<正>Acta Oceanologica Sinica(AOS)is a comprehensive academic journal edited by the Editorial Committee of Acta Oceanologica Sinica and is designed to provide a forum for important research papers of the marine scientific community which reflect the information on a worldwide basis.The journal publishes scholarly papers on marine science and technology,including physics,chemistry,biology,     

Estimation of Sediment Properties during Benthic Impact Experiments

Sediment properties, such as water content and density, have been used to estimate the dry and wet weights, as well as the volume of sediment recovered and discharged, during benthic impact experiments conducted in the Pacific and Indian Oceans. The estimates show that the weights of dry (355-1332 t) and wet sediment (1651-4888 t) recovered during the experiments, are not only a function of the total duration and distance covered during the experiment, but also depend on water content and density of the sediment. Estimation of dry sediment and its volumetric ratio in the discharge, are key parameters for calculating the discharged volume. The estimated volume of wet sediment recovered (1427-4049 m 3 ) as well as discharged (2693-6951 m 3 ) during the experiments, provide important inputs to evaluate the sediment resettlement and migration. Using these estimates, the average depth of excavation on the seafloor, can also been calculated. However, the stages of sediment recovery and discharge are expressed differently in some of the experiments. In order to standardize these, different stages have been identified, and definitions of certain terms have been suggested, for use in the future. The methods of calculating different properties, as well as weight and volume of discharged sediment are described in the paper for use in other applications concerning deep-sea discharges.