Dynamic analysis of offshore wind turbine in clay considering soil–monopile–tower interaction

A comprehensive study is performed on the dynamic behavior of offshore wind turbine (OWT) structure supported on monopile foundation in clay. The system is modeled using a beam on nonlinear Winkler foundation model. Soil resistance is modeled using American Petroleum Institute based cyclic p–y and t–z curves. Dynamic analysis is carried out in time domain using finite element method considering wind and wave loads. Several parameters, such as soil–monopile–tower interaction, rotor and wave frequencies, wind and wave loading parameters, and length, diameter and thickness of monopile affecting the dynamic characteristics of OWT system and the responses are investigated. The study shows soil–monopile–tower interaction increases response of tower and monopile. Soil nonlinearity increases the system response at higher wind speed. Rotor frequency is found to have dominant role than blade passing frequency and wave frequency. Magnitude of wave load is important for design rather than resonance from wave frequency.     

On the effective seismic input for non-linear soil-structure interaction systems

Two equivalent semi-discrete formulations are presented for the problem of the transient response of soil-structure interaction systems to seismic excitation, considering linear behaviour of the soil material and arbitrary non-linear structural properties. One formulation results in a direct method of analysis in which the motion in the structure and the entire soil medium, rendered finite by an artificial absorbing boundary, is determined simultaneously. The other represents a substructuring technique in which the structure and the soil are analysed separately. The forces induced in the discretized system by the incident seismic motion are obtained as part of the general formulation by using the free-field motion of the unaltered soil as the earthquake input. It is shown that these forces act within the soil region in the direct method, but only on the soil-structure interface in the substructure formulation. Both sets of forces, however, involve only the displacements and tractions acting on the fictitious surface in the unaltered (linear) soil which coincides with the soil-structure interface of the complete system. It is shown, further, that the free-field displacements alone define a minimal set of data for evaluating the seismic response of the structure, since the tractions and displacements on that surface are interrelated. In practice, the minimal set must be obtained by extrapolating the available information, as the free-field ground motion at a site is usually specified at a single reference point.     

A discontinuous Galerkin method for seismic soil–structure interaction analysis in the time domain

A technique for modeling transient wave propagation in unbounded media is extended and applied to seismic soil–structure interaction analysis in the time domain. The technique, based on the discontinuous Galerkin method, requires lower computational cost and less storage than the boundary element method, and the time‐stepping scheme resulting from Newmark's method in conjunction with the technique is unconditionally stable, allowing for efficient and robust time‐domain computations. To extend the technique to cases characterized by seismic excitation, the free‐field motion is used to compute effective forces, which are introduced on the boundary of the computational domain containing the structure and the soil in the vicinity of the structure. A numerical example on a dam–foundation system subjected to seismic excitation demonstrates the performance of the method. Copyright © 2003 John Wiley & Sons, Ltd.     

Seismic soil–structure interaction in multi‐span bridges: Application to a railway bridge

The effects of soil‐structure interaction on the seismic response of multi‐span bridges are investigated by means of a modelling strategy based on the domain decomposition technique. First, the analysis methodology is presented: kinematic interaction analysis is performed in the frequency domain by means of a procedure accounting for radiation damping, soil–pile and pile‐to‐pile interaction; the seismic response of the superstructure is evaluated in the time domain by means of user‐friendly finite element programs introducing suitable lumped parameter models take into account the frequency‐dependent impedances of the soil–foundation system. Second, a real multi‐span railway bridge longitudinally restrained at one abutment is analyzed. The input motion is represented by two sets of real accelerograms: one consistent with the Italian seismic code and the other constituted by five records characterized by different frequency contents. The seismic response of the compliant‐base model is compared with that obtained from a fixed‐base model. Pile stress resultants due to kinematic and inertial interactions are also evaluated. The application demonstrates the importance of performing a comprehensive analysis of the soil–foundation–structure system in the design process, in order to capture the effects of soil‐structure interaction in each structural element that may be beneficial or detrimental. Copyright © 2011 John Wiley & Sons, Ltd.     

Axisymmetric dynamic response of the multi-layered transversely isotropic medium

By virtue of the precise integration method (PIM) and the technique of mixed variable formulations, solutions for the dynamic response of the multi-layered transversely isotropic medium subjected to the axisymmetric time-harmonic forces are presented. The planes of cross anisotropy are assumed to be parallel to the horizontal surface of the stratified media. Four kinds of vertically acting axisymmetric loads are prescribed either at the external surface or in the interior of the soil system. Thicknesses and number of the medium strata are not limited. Employing the Hankel integral transform in cylindrical coordinate, the axisymmetric governing equations in terms of displacements of the multi-layered media are uncoupled. Applying mixed variable formulations, more concise first-order ordinary differential matrix equations from the uncoupled motion equations can be obtained. Solutions of the ordinary differential matrix equations in the transformed domain are acquired by utilizing the approach of PIM. Since PIM is highly accurate to solve the sets of first-order ordinary differential equations, any desired accuracy of the solutions can be achieved. All calculations are based on the corresponding algebraic operations and computational efforts can be reduced to a great extent. Comparisons with the existing numerical solutions are made to confirm the accuracy of the present solutions proposed by this procedure. Several examples are illustrated to explore the influences of the type and degree of material anisotropy, the frequency of excitation and loading positions on the dynamic response of the stratified medium.     

Response of tension-leg platforms to vertical seismic excitations

Presented is a systematic approach, for analysing the vertical motion, tendon force and foundation uplift of a tension-leg platform (TLP) when the subsea soil is excited by vertical seismic waves. The complex problem of multiple interactions among the soil, foundation, fluid and platform can be mathematically modelled using the substructure technique. Having obtained the frequency dependent impedance function for each substructure, the total system is then solved in the frequency domain. A specific TLP is analysed to show the application of the procedures developed and the importance of response to vertical seismic excitation.     

Dynamic response of flexible strip-foundations by boundary and finite elements

A time domain Boundary Element-Finite method is employed to determine the dynamic response of flexible surface two-dimensional foundations under conditions of plane strain placed on an elastic soil medium and subjected either to transient external forces or to obliquely incident seismic waves. The elastic, isotropic, and homogeneous soil medium is treated by the time domain Direct Boundary Element Method, while the flexible foundation is treated by the Finite Element Method. The two methods are appropriately combined through equilibrium and compatibility considerations at the soil-foundation interface. Parametric studies examining the effect of the relative stiffness between the foundation and the soil and the spatial distribution of the dynamic disturbances on the foundation response are presented.     

Seismic response of intake towers including dam–tower interaction

The seismic response of the intake–outlet towers has been widely analyzed in recent years. The usual models consider the hydrodynamic effects produced by the surrounding water and the interior water, characterizing the dynamic response of the tower–water–foundation–soil system. As a result of these works, simplified added mass models have been developed. However, in all previous models, the surrounding water is assumed to be of uniform depth and to have infinite extension. Consequently, the considered added mass is associated with only the pressures created by the displacements of the tower itself. For a real system, the intake tower is usually located in proximity to the dam and the dam pressures may influence the equivalent added mass. The objective of this paper is to investigate how the response of the tower is affected by the presence of the dam. A coupled three‐dimensional boundary element‐finite element model in the frequency domain is employed to analyze the tower–dam–reservoir interaction problem. In all cases, the system response is assumed to be linear, and the effect of the internal fluid and the soil–structure interaction effects are not considered. The results suggest that unexpected resonance amplifications can occur due to changes in the added mass for the tower as a result of the tower–dam–reservoir interaction. Copyright © 2008 John Wiley & Sons, Ltd.     

Dynamic analysis of 3-D flexible embedded foundations by a frequency domain BEM-FEM

A study on the dynamic response of three-dimensional flexible foundations of arbitrary shape, embedded in a homogenous, isotropic and linear elastic half-space is presented. Both massive and massless foundations are considered. The soil-foundation system is subjected to externally applied forces, and/or to obliquely incident seismic waves. The numerical method employed is a combination of the frequency domain Boundary Element Method, which is used to simulate the elastic soil medium, and the Finite Element Method, on the basis of which the stiffness matrix of the foundation is obtained. The foundation and soil media are combined by enforcing compatibility and equilibrium conditions at their common interface. Both relaxed and completely bonded boundary conditions are considered. The accuracy of the proposed methodology is partially verified through comparison studies with results reported in the literature for rigid embedded foundations.     

Response of circular flexible foundations subjected to horizontal and rocking motions

A methodology using modal analysis is developed to evaluate dynamic vertical displacements of a circular flexible foundation resting on soil media subjected to horizontal and rocking motions. The influence of the soil reaction forces on the foundation is considered by introducing modal impedance functions, which can be determined by an efficient procedure with ring elements. The displacements of the foundation can then be easily solved by modal superposition. Parametric studies for modal responses of the flexible foundation indicate that the coupled response of the foundation is significantly influenced by relative stiffness among the foundation and the soil medium, vibration frequency range, foundation mass, and boundary contact conditions. The welded boundary condition should be considered to predict the coupling response while the relaxed boundary condition may be used to predict approximately the vertical displacements. As a foundation with a relative stiffness ratio more than three, it is found that the foundation can be considered as rigid to calculate coupling displacements. For a slightly flexible foundation, considerations of three modes are sufficient enough to obtain accurate foundation responses. Moreover, at low frequencies, the coupling effect due to higher mode can be neglected.     

Motion of foundation on a layered soil medium — I. Impedance characteristics

An impedance matrix is derived for the relationship between displacements and external excitations of a rigid or flexible foundation embedded in a layered soil medium. The unknown contact distributed force between the foundation and soil is expanded in the frequency domain as a twofold series of azimuthal and radial components; each term represents a basic or fundamental distribution. As a result, the total response of the soil, either of displacements or stresses, has the same type of series expression except for the fundamental distributions replaced by influence functions. The coefficients of the series expansion, appearing in both equilibrium conditions of the foundation and compatibility conditions on the contact surface, relate the foundation displacements and excitations, and, therefore, result in the impedance matrix. Avoidance of integral equations in the soil-structure interaction analysis is the merit of the present approach.     

Effects of soil–structure interaction on seismic base isolation

The effects of soil–structure interaction on the performance of a nonlinear seismic base isolation system for a simple elastic structure are examined. The steady-state response of the system to harmonic excitation is obtained by use of the equivalent linearization method. Simple analytical expressions for the deformation of the base isolation system and of the superstructure at resonance are obtained in terms of an effective replacement oscillator characterized by amplitude-dependent frequency, damping ratio, and excitation. Numerical results suggest that the seismic response of a structure resting on an inelastic base isolation system may be larger when the flexibility of the soil is considered than the corresponding response obtained by ignoring the effects of soil–structure interaction. It is shown that, in the undamped case and in the absence of soil–structure interaction effects, a critical harmonic excitation exists beyond which the steady-state resonant response of the isolators and structure become unbounded.     

Seismic soil–structure interaction of massive flexible strip-foundations embedded in layered soils by hybrid BEM–FEM

A study on the seismic response of massive flexible strip-foundations embedded in layered soils and subjected to seismic excitation is presented. Emphasis is placed on the investigation of the system response with the aid of a boundary element–finite element formulation proper for the treatment of such soil–structure interaction problems. In the formulation, the boundary element method (BEM) is employed to overcome the difficulties that arise from modeling the infinite soil domain, and the finite element method (FEM) is applied to model the embedded massive flexible strip-foundation. The numerical solution for the soil–foundation system is obtained by coupling the FEM with the BEM through compatibility and equilibrium conditions at the soil–foundation and soil layer interfaces. A parametric study is conducted to investigate the effects of foundation stiffness and embedment on the seismic response.     

A model for the 3D kinematic interaction analysis of pile groups in layered soils

The paper presents a numerical model for the analysis of the soil–structure kinematic interaction of single piles and pile groups embedded in layered soil deposits during seismic actions. A finite element model is considered for the pile group and the soil is assumed to be a Winkler‐type medium. The pile–soil–pile interaction and the radiation problem are accounted for by means of elastodynamic Green's functions. Condensation of the problem permits a consistent and straightforward derivation of both the impedance functions and the foundation input motion, which are necessary to perform the inertial soil–structure interaction analyses. The model proposed allows calculating the internal forces induced by soil–pile and pile‐to‐pile interactions. Comparisons with data available in literature are made to study the convergence and validate the model. An application to a realistic pile foundation is given to demonstrate the potential of the model to catch the dynamic behaviour of the soil–foundation system and the stress resultants in each pile. Copyright © 2009 John Wiley & Sons, Ltd.     

A simplified multisupport response spectrum method

A simplified multisupport response spectrum method is presented.The structural response is a sum of two components of a structure with a first natural period less than 2 s.The first component is the pseudostatic response caused by the inconsistent motions of the structural supports,and the second is the structural dynamic response to ground motion accelerations.This method is formally consistent with the classical response spectrum method,and the effects of multisupport excitation are considered for any modal response spectrum or modal superposition.If the seismic inputs at each support are the same,the support displacements caused by the pseudostatic response become rigid body displacements.The response spectrum in the case of multisupport excitations then reduces to that for uniform excitations.In other words,this multisupport response spectrum method is a modification and extension of the existing response spectrum method under uniform excitation.Moreover,most of the coherency coefficients in this formulation are simplified by approximating the ground motion excitation as white noise.The results indicate that this simplification can reduce the calculation time while maintaining accuracy.Furthermore,the internal forces obtained by the multisupport response spectrum method are compared with those produced by the traditional response spectrum method in two case studies of existing long-span structures.Because the effects of inconsistent support displacements are not considered in the traditional response spectrum method,the values of internal forces near the supports are underestimated.These regions are important potential failure points and deserve special attention in the seismic design of reticulated structures.     

Dynamic analysis of large 3-D underground structures by the bem

An up to date literature survey on the dynamics of underground structures is presented briefly. The dynamic response of large three-dimensional underground structures to external or internal dynamic forces or to seismic waves is numerically determined by the frequency domain boundary element method. This method is used to model both the structure and the soil medium, which are assumed to behave as linear elastic or viscoelastic bodies. The full-space dynamic fundamental solution is employed in the formulation and this requires a free soil surface discretization, confined to a finite portion around the area of interest, in addition to soil—structure interface and free structural surface discretizations. The dynamic disturbances can have a harmonic or a transient time variation. The transient case is treated with the aid of numerical Laplace transforms with respect to time. Various numerical examples involving lined cavities and long lined tunnels buried in the full- or the half-space subjected to harmonic or transient external forces or seismic waves are presented to illustrate the method and demonstrate its advantages.     

Soil–structure interaction effects on seismic inelastic analysis of 3-D tunnels

This paper investigates the importance of seismic soil–structure interaction in three-dimensional lined tunnels, assuming inelastic material behaviour for both the concrete liner and the soft rock type of soil. The seismic response of the soil–structure system is determined by the finite element method (FEM) in the time domain. Viscous absorbing boundaries are used in conjunction with the discretization of the rock medium. Both the rock medium and the concrete liner are assumed to behave inelastically on the basis of the continuum damage mechanics theory. The seismic waves are assumed to have any arbitrary time variation and direction of propagation. The system is analysed with and without soil–structure interaction in order to assess its importance on the response of the system. Through parametric studies, the influence of the most critical parameters affecting the structural response is determined and critically discussed.     

The effect of seasonally frozen soil on stochastic response of elevated water tank under random excitation

Significant seismic events have occurred around the world during winter months in regions where cold temperatures cause ground freezing. Current seismic design practice does not address the effects of cold temperatures in the seasonally frozen areas. Since many elevated water tank structures in cold regions are located in seismic active zones, determining the effect of seasonally frozen soil on the stochastic response of elevated water tank structures subjected to random seismic excitation is an important structural consideration. A three dimensional finite element model, which considers viscous boundaries, was built up to obtain the stochastic seismic behavior of an elevated water tank–fluid–soil interaction system for frozen soil condition. For this model, the power spectral density function represents random ground motion applied to each support point of the three dimensional finite element model of the elevated water tank–fluid–soil interaction system. Numerical results show that the soil temperature affects the seismic response of the elevated water tank; whereas the variation in the thickness of the frozen soil causes insignificant changes on the response. In addition, the effect of the variation in water tank’s fullness on the stochastic response of the coupled system is investigated in the study. As a result, the seasonal frost changes the foundation soil stiffness and may impact seismic behavior of the water tank.     

Investigation of seismic behavior of fluid–rectangular tank–soil/foundation systems in frequency domain

Main purpose of this study is to evaluate the dynamic behavior of fluid–rectangular tank–soil/foundation system with a simple and fast seismic analysis procedure. In this procedure, interaction effects are presented by Housner's two mass approximations for fluid and the cone model for soil/foundation system. This approach can determine; displacement at the height of the impulsive mass, the sloshing displacement and base forces for the soil/foundation system conditions including embedment and incompressible soil cases. Models and equations for proposed method were briefly explained for different tank–soil/foundation system combinations. By means of changing soil/foundation conditions, some comparisons are made on base forces and sloshing responses for the cases of embedment and no embedment. The results showed that the displacements and base shear forces generally decreased, with decreasing soil stiffness. However, embedment, wall flexibility, and soil–structure interaction (SSI) did not considerably affect the sloshing displacement.