Laboratory modelling of gravel braided stream morphology

Hydraulic modelling principles, together with a knowledge of channel pattern thresholds, allow the development of a small scale model of a gravel braided stream with flow characteristics and equivalent dimensions of a natural river. The forms and processes of natural gravel braided rivers are reproduced by imposing a constant flume discharge and slope, and maintaining approximate equilibrium with an adjustable sediment feed. Beginning from a straight trough, braiding is initiated by development of a series of alternating bars and scour pools which produce bends of increasing amplitude, leading finally to channel division. These lobate bars accrete downstream by deposition of bed material at their margins, often in the form of avalanche faces. Together with the scour pools with which they are necessarily closely associated, these bars are the fundamental elements of the channel pattern. Channel migration and division is a response to the development of bars, and these adjustments leave portions of the originally active bars in the form of exposed and eroded remnants. Complex flats built from these lobate forms show varying degrees of preservation of the original depositional units, but the model allows observation of the systematic construction of some flats. Sorting of sediment on active bars with avalanche faces shows a distinct fining downstream. This may be the result of the accretion of fining upwards avalanche faces along the bar margins rather than a ‘winnowing out’ of fine material. The processes and forms observed in the model appear to be very similar to those occurring in natural gravel braided streams during peak flows.     

Lateral sediment transport by bedforms in a meander bend

Bedforms and their migration are among the most important features determining bed load transport on point bars in sand-bedded rivers. A case study has been carried out in the Danish river Gels Å in a bend with equilibrium point bar topography. Bedforms (dunes) were repeatedly surveyed to determine the bedform migration on the point bar surface. Bedforms occur in two categories in the bend: primary dunes and secondary dunes migrating transversely in the troughs between primary dunes. The study shows that the migration of these bedforms can account for the entire lateral transport known to concentrate the transport in the convex half of the cross section at the bend exit. The bedform transport is induced by both dune categories, partly by turning of the primary dunes towards the convex bank and partly by the migration of secondary dunes. In certain areas, the two categories operate together and thus make the lateral transport particularly large; it is shown that almost 60 per cent of the entire lateral transport in the bend takes place within less than 30 per cent of the streamwise extent of the point bar.     

Formation of stationary alternate bars in a steep channel with mixed-size sediment: A flume experiment

Alternate bars were formed by sediment transport in a flume with Froude-modelled flow and relative roughness characteristic of gravel-boulder channels with steep slopes. The flume (0.3 m wide × 7.5 m long) was filled with a sand-gravel mixture, which was also fed into the top of the flume at a constant rate under constant discharge. Channel slope was set at 0.03. Initially, coarse particles accumulated on incipient bar heads near one side of the flume and diverted flow and bedload transport across the flume toward a pool scoured against the opposite flume wall downstream. Sorting in the pool directed coarse particles onto the next bar head downstream. Alternate sequences of pools and coarse bar heads were thereby linked down the entire flume by interactions of sediment sorting, flow, and channel morphology. During episodes of bar construction, unsorted bedload invaded interior bar surfaces and was deposited. Persistent deposition of coarse particles on bar heads prevented downstream migration of bars by inhibiting bar-head erosion and bedload transport over bars. Likely factors leading to bar-head stabilization in modelled gravel-bed channels are coarse mixed-size sediment, steep channel gradients, and shallow depths.     

Grain‐size distribution patterns of a point bar system in the Usri River,India

Grain‐size distribution patterns in a point bar system of the Usri River, India, were critically analysed in the light of log‐normal, log‐hyperbolic and log‐skew‐Laplace distribution models. Sand samples were collected from the cross‐bedding foreset of different sizes of bedform; the objectives were to (i) study whether bedform heights have any role in grain‐size distribution patterns, (ii) offer a best‐fit statistical model, (iii) study the downstream variation of size‐sorting in a point bar system, and (iv) study the mechanism of grain sorting. The results indicate that the bedform heights have no role in grain‐size distribution patterns. Quantitatively when the errors in three distribution models were analysed, it was observed that the log‐normal distribution is the best‐fit statistical model and the next one is the log‐skew‐Laplace. However, in the upper reaches of the river, log‐normal distribution is the best‐fit model in the case of large bedforms, whereas in the lower reaches the log‐normal model is the best‐fit one in the case of small bed forms. It is also observed that within a point bar, for large and small bedforms, there is a tendency for mean grain size to decrease downstream. Between point bars for large bedforms there is no consistency in decreasing grain size downstream, whereas for small bed forms the decrease of grain size downstream is observed except near the confluence at Palkia. With distance of transport, the coarser and finer fractions of sediments are gradually chopped off. The coarser fractions are buried below the advancing bedforms on the lee sides and the finer ones are transported further downstream. Thus the finer admixture giving rise to the fining‐upward sequence overlies a carpet of coarser materials. This mechanism provides a clue to the process of grain sorting in the fluvial environment. An interpretation has been offered for the log‐normality of the grain‐size distribution pattern. During prolonged transportation in a fluvial environment, the larger grain‐size fractions are gradually chopped off and buried below the advancing bedforms on their lee sides. On the other hand, the finer fractions are transported further downstream in suspension. Thus the narrow, intermediate size fraction takes active part in the distribution patterns leading to the generation of unimodality and a symmetric distribution pattern downstream, which are the main criteria for log‐normality. Similarly, increase of bedform size is the effect of increase of stream power and Froude number leading to the selective segregation of bed materials. Thus the intermediate size fractions take a more active part than the coarser and the finer size fractions in developing log‐normality. Besides the hydrodynamic parameters of the Usri, coarsening of grain size downstream has been attributed to (i) the aggrading nature of the Usri downstream, and (ii) the contribution of coarser materials to the Usri by its tributaries and bank erosion. Copyright © 2006 John Wiley & Sons, Ltd.     

Velocity characteristics along a small step–pool channel

This paper summarizes measurements of velocity along three reaches of a small mountain channel with step–pool bedforms. A one‐dimensional electromagnetic current meter was used to record velocity fluctuations at 37 fixed measurement points during five measurement intervals spanning the peak of the annual snowmelt hydrograph. Measurement cross‐sections were located upstream from a bed‐step, at the step lip, downstream from the step, and in a uniform‐gradient run. Data analyses focused on characteristics of velocity profiles, and on correlations between velocity characteristics and the potential control variables bedform type, reach gradient and flow depth. To test the hypothesis that velocity characteristics are related to channel bedform types, ANOVA and ANCOVA tests were performed for the average velocity and coefficient of variation of point velocity data. Results indicate that high frequency velocity variations correlate to some degree with both channel characteristics and discharge. Velocity became more variable as stage increased, particularly at low‐gradient reaches with less variable bed roughness. Velocity profiles suggest that locations immediately downstream from bed‐steps are dominated by wake turbulence from mid‐profile shear layers. Locations immediately upstream from steps, at step lips, and in runs are dominated by bed‐generated turbulence. Adverse pressure gradients upstream and downstream from steps may be enhancing turbulence generation, whereas favourable pressure gradients at steps are suppressing turbulence. The bed‐generated turbulence and skin friction of runs appear to be less effective energy dissipators than the wake‐generated turbulence and form drag of step–pool bedforms. Copyright © 2000 John Wiley & Sons, Ltd.     

Development of bedforms due to waves blocked by a counter current

Experiments are conducted in a laboratory flume on the propagation of a surface wave against unidirectional flow with a sediment bed. This article presents the spatial variation of bedforms induced by the wave-blocking phenomenon by a suitably tuned uniform fluid flow and a counter-propagating wave. The occurrence of wave-blocking is confirmed by finding a critical wave frequency in a particular flow discharge in which the waves are effectively blocked and is established using the linear dispersion relation. The purpose of this work is to identify wave-blocking and its influence on the development of bedforms over the sediment bed. Interestingly bedform signatures are observed at a transition of bedforms in three zones, with asymmetric ripples having a steeper slope downstream face induced by the incoming current, followed by flat sand bars beneath the wave-blocking zone and more symmetric ripples below the wave-dominated region at the downstream. This phenomenon suggests that the sediment bed is segmented into three different regions of bed geometry along the flow. The deviations of mean flows, Reynolds stresses, turbulent kinetic energy, and power spectral density due to the wave-blocking phenomenon are presented along the non-uniform flow over sediment bed. The bottom shear stress, bed roughness and stochastic nature of the bedform features are also discussed. The results are of relevance to engineers and geoscientists concerned with contemporary process as well as those interested in the interpretation of palaeoenvironmental conditions from fossil bedforms. © 2019 John Wiley & Sons, Ltd.     

Gravel transport and morphological change in braided sunwapta river,Alberta, Canada

The relation between morphological change and patterns of variation in bedload transport rate in braided streams was observed by repeated, daily topographic surveys over a 25 day study period in a 60 m reach of the proglacial Sunwapta River, Alberta, Canada. There are two major periods of morphological change, each lasting several days and each involving the complete destruction and reconstruction of bar complexes. Bar complex destruction was caused by redirection of the flow and by downstream extension of the confluence scour zone upstream. Reconstruction involved accretion of unit bars on bar head, flank and tail and in one case was initiated by disection of a large, lobate unit bar. High rates of sediment movement, measured from net scour and fill of the cross-sections, coincided with these morphological changes. Sediment was supplied from both bed and bank erosion, and patterns and distances of transfer were highly variable. Rates of transport estimated by matching upstream erosional volumes with downstream deposition were much greater than those estimated from either a step-length approach or a sediment budget. Measurements of scour and fill and observations of morphological change indicate that step lengths (virtual transport distances) were typically 40–100m during a diurnal discharge cycle. Shorter step lengths occurred when transfer was confined to a single anabranch and longer steps involved channel changes at the scale of the entire reach. Sediment budgeting was used to describe the spatial patterns of sediment transport associated with the morphological changes and to estimate minimum daily reach-averaged transport rates. Mean bedload transport rates correlate with discharge, but with considerable scatter. The largest deviations from the mean relation can be tied to phases of channel incision, bank erosion, scour hole migration, bar deposition and channel filling apparently controlled by changes and fluctuations in sediment supply from upstream, independent of discharge. These are interpreted as field evidence of ‘autopulses’ or ‘macropulses’ in bedload transport, previously observed only in laboratory models of braided streams.     

The bed morphology of upland single‐thread channels in semi‐arid environments: evidence of repeating bedforms and their wider implications for gravel‐bed rivers

Single‐thread, gravel‐bed streams of moderate slope in the northern Negev are characterized by three channel units: bars exhibit steeper than average slopes and poorly sorted mixtures of small–medium cobbles and coarse–very coarse pebbles; flats are associated with more gentle slopes and well‐sorted medium–fine pebbles and granules; and transitional units have intermediate slopes and grain size. In general, all three units are planar, span the full channel width and have well‐defined boundaries. Bars and flats are more common than the transitional units and alternate downstream for distances of several hundred metres, forming sequences that are reminiscent of the riffle–pool structure commonly observed in humid‐temperate gravel‐bed rivers. A notable contrast is the absence of significant bed relief: bars lack crests and flats lack depressions. The relative lack of bed relief in bar–flat sequences is attributed to the high rate of sediment supply from the sparsely vegetated hillslopes which promotes the infilling of depressions and to the erosion of crests under conditions of intense transport. This reduction of bed relief lowers channel roughness, which in turn increases flow velocity and, therefore, the ability of the channel to transmit the large sediment loads it receives. Although our analyses pertain to a semi‐arid river system, the results have wider implications for understanding the adjustment of channel bedform to high sediment loads in other fluvial environments. Copyright © 2012 John Wiley & Sons, Ltd.     

The geormorphology of subalpine snow avalanche runout zones: San juan mountains,colorado

A comparison was made between the distal ends of twenty-two avalanche and fifteen non-avalanche slopes in the San Juan Mountains of Colorado, U.S.A. All slopes occurred in the subalpine zone. Six characteristics were used for analysis: type of slope, surface material, longitudinal profile, perched debris or debris tails, avalanche impact on opposite valley wall, and transverse profile. Both fan and roadbank avalanche slope types were found along with the non-avalanche slopes. Almost all slopes were turf covered rather than talus since the work was done below treeline. Twenty avalanche slopes had a distinctive concave longitudinal profile. Little debris of any kind was found since the slopes were in an area of insignificant amounts of detritus. Many of the larger and two of the smaller avalanche slopes showed evidence of impact upon the opposite slope. Eighteen of the avalanche slopes had convex transverse profiles.     

Bedform development and its effect on bed stabilization and sediment transport based on a flume experiment with non-uniform sediment

Non-uniform sediment deposited in a confined, steep mountain channel can alter the bed surface composition. This study evaluates the contribution of geometric and resistance parameters to bed sta-bilization and the reduction in sediment transport. Flume experiments were done under various hydraulic conditions with non-uniform bed material and no sediment supply from upstream. Results indicate that flume channels respond in a sequence of coarsening and with the formation of bedform-roughness features such as rapids, cascades, and steps. A bedform development coefficient is introduced and is shown to increase (i.e. vertical sinuosity develops) in response to increasing shear stress during the organization process. The bedform development coefficient also is positively correlated with the critical Shields number and Manning's roughness coefficient, suggesting the evolution of flow resistance with increasing bedform development. The sediment transport rate decreases with increasing bed shear stress and bedform development, further illustrating the effect of bed stabilization. An empirical sedi-ment transport model for an equilibrium condition is proposed that uses the bedform development coefficient, relative particle submergence (i.e. the ratio of mean water depth and maximum sediment diameter), modified bed slope, and discharge. The model suggests bedform development can play a primary role in reducing sediment transport (increasing bed stabilization). The model is an extension of Lane's (1955) relation specifically adapted for mountain streams. These results explain the significance of bedform development in heightening flow resistance, stabilizing the bed, and reducing sediment transport in coarse, steep channels.     

Turbulent flow over a dune: Green River,Colorado

Detailed echo‐sounder and acoustic Doppler velocimeter measurements are used to assess the temporal and spatial structure of turbulent flow over a mobile dune in a wide, low‐gradient, alluvial reach of the Green River. Based on the geometric position of the sensor over the bedforms, measurements were taken in the wake, in transitional flow at the bedform crest, and in the internal boundary layer. Spatial distributions of Reynolds shear stress, turbulent kinetic energy, turbulence intensity, and correlation coefficient are qualitatively consistent with those over fixed, two‐dimensional bedforms in laboratory flows. Spectral and cospectral analysis demonstrates that energy levels in the lee of the crest (i.e. wake) are two to four times greater than over the crest itself, with minima over the stoss slope (within the developing internal boundary layer). The frequency structure in the wake is sharply defined with single, dominant peaks. Peak and total spectral and cross‐spectral energies vary over the bedform in a manner consistent with wave‐like perturbations that ‘break’ or ‘roll up’ into vortices that amalgamate, grow in size, and eventually diffuse as they are advected downstream. Fluid oscillations in the lee of the dune demonstrate Strouhal similarity between laboratory and field environments, and correspondence between the peak frequencies of these oscillations and the periodicity of surface boils was observed in the field. Copyright © 2005 John Wiley & Sons, Ltd.     

Geomorphological effectiveness of floods to rework gravel bars: Insight from hyperscale topography and hydraulic modelling

Bars are key morphological units in river systems, fashioning the sediment regime and bedload transport processes within a reach. Reworking of these features underpins channel adjustment at larger scales, thereby acting as a key determinant of channel stability. Despite their importance to channel evolution, few investigations have acquired spatially continuous data on bar morphology and sediment-size to investigate bar reworking. To this end, four bars along a 10 km reach of a wandering gravel-bed river were surveyed with terrestrial laser scanning (TLS), comparing downstream changes in slope, bed material size and channel planform. Detrended standard deviations (σ_z) were extracted from TLS point clouds and correlated to underlying physically measured median grain-size (D₅₀), across a greater range of σ_z values than have hitherto been reported. The resulting linear regression model was used to create a 1 m resolution median grain-size map. A fusion of airborne LiDAR and optical-empirical bathymetric mapping was used to develop reach-scale digital elevation models (DEMs) for rapid two-dimensional hydraulic modelling using JFlow® software. The ratio of dimensionless shear stress over critical shear stress was calculated for each raster cell to calculate the effectiveness of a range of flood events (2.33–100 year recurrence intervals) to entrain sediment and rework bar units. Results show that multiple bar forming discharges exist, whereby frequent flood flows rework tail and back channel areas, while much larger, less frequent floods are required to mobilise the coarser sediment fraction on bar heads. Valley confinement is shown to exert a primary influence on patterns of bar reworking. Historical aerial photography, hyperscale DEMs and hydraulic modelling are used to explain channel adjustment at the reach scale. The proportion of the bar comprised of more frequently entrained units (tail, back channel, supra-platform) relative to more static units (bar head) exerts a direct influence upon geomorphic sensitivity. © 2018 John Wiley & Sons, Ltd.     

Flow and sedimentary processes in the meandering river South Esk,Glen Clova,Scotland

Channel geometry, flow and sedimentation in a meander bend of the River South Esk were studied from bankfull stages (January–February) to low water stages (May) in 1974. Bed topography varied little over the study period, showing a typical pool and ripple geometry. Variation of mean depth and velocity with discharge differed from section to section around the bend, due primarily to locally varying flow resistance with stage. The flow pattern for all stages was dominated by a single spiral over the point bar, with a development zone at the bend entrance. Deviation of bed shear stress from the mean flow direction was in general accord with theory, especially for high stages. The use of a uniform longitudinal water surface slope in the calculation of bed shear stress is not justified because of a complicated water surface topography, also such calculated shear may not represent effective bed shear on grains, as it accounts also for energy losses associated with secondary flows. Dunes covered much of the bar at high stages, with increasing proportions of ripples, sand ribbons and lower phase plane beds at low stages. Local flow resistance generally decreases from dunes, diminished and ripple-backed dunes, ripples, sand ribbons to plane beds, and bed forms are predicted quite well by the stream power-grain size scheme. Mean size, sorting and skewness of sediment over the bed changes little with stage. In general, size decreases, sorting improves and skewness changes from positive to negative from the talweg to the inner bank, and in the downstream direction. Allen's (1970a, b) force balance equation for moving bed load particles is supported for bankfull stage, with some reservations, and textural characteristics are explained by progressive sorting in the direction of sediment transport. Large-scale trough cross stratification (with some flat bedding) formed at high stage by dunes (and lower phase plane beds) dominates the point bar sediments. Alternations of fine-medium sand (often cross-laminated) and vegetation-rich layers result from periodic deposition on the grassed upper bar surface. Fining upwards sequences produced by lateral channel migration are modified by a coarsening upward subsequence in the upstream bar region where spiral flow is developing from the bend upstream.     

Alternate bar development in an alpine river following engineering works

Formation and development of alternate bars in an engineered mountainous reach of the Arc River, France, is studied using photo analysis, 1D modelling and by applying theoretical and empirical models for alternate bar systems. Alternate bars already existed in the 80s in the form of a stable confined wandering system. In 1994, the river bed was flattened after engineering works. However, aerial photographs and cross-sectional profiles show that bars rapidly recovered within a few years. The alternate bar system evolved rapidly with a reduction of the number of bars and so an increasing bar length. The width-to-depth ratio, the slope change, the bend upstream of the reach, and the sediment supplies are the main controls of bar formation and evolution. The system appears to lead to force bars due to the bend but also due to a bridge in the downstream part of the reach. Nevertheless some free mobile bars are still observed in the middle of the reach. A discussion on the alternate bar formation is provided using empirical and analytical models. Finally, impacts of low flows and vegetation seem to be significant in the stabilization of the system toward a confined wandering system as observed before the engineering works.     

Channel bar dynamics on multi‐decadal timescales in an active meandering river

Occurrence and development of channel bars are major components of the morphodynamics of rivers and their relation to river meandering has been much explored through theory and experimentation. However, field and documentary data of characteristics and evolution over timescales from years to several decades are lacking. Four sets of aerial photographs in the period 1984–2007 were used to map and quantify bar numbers and areas in GIS on an active meandering reach. Bar types were classified. Additional temporal resolution was provided by annual ground photography and mapping for 1981–2010. Analysis was extended backward by use of large scale Ordnance Survey maps from 1873 onwards. As expected, point bars are the most common type but ‘free’ bars of several types are major components of bar deposition. Point bars and attached bars are significantly larger in size than mid‐channel and side bars. Spatial distribution of bars varies down the reach and over time but is related to channel sinuosity, gradient and mobility and to bend evolution. Different types of bar occur in distinctive channel locations, with point and concave‐bend bars in zones of high curvature. Bar activity shows a relation with discharge events and phases and possibly with changing riparian conditions, but superimposed on this is a common sequence of bar evolution from incipient gravel mid‐channel bars to full floodplain integration. This life‐cycle is identified as 7–9 years on average. No evidence for mobility of free bars within the course is found. The results are compared with bar and bend theory; the bars are forced and conform in general to bend theory but detailed variation relates to geomorphic factors and to autogenic sequences of bends and bars. Mid‐channel bars are width induced. Variability of bar occurrence needs to be taken into account in river management and ecological evaluation, including for the EU WFD. Copyright © 2011 John Wiley & Sons, Ltd.     

Berm formation and dynamics on a gently sloping beach; the effect of water level and swash overtopping

Berm formation and morphological development of the beach face have been observed during a neap–neap tidal cycle on the gently sloping and accreting beach at Vejers, Denmark. During the field campaign, an intertidal bar migrated onshore and stabilized as a berm on the foreshore. A new intertidal bar occurred on the lower beach face, migrated onshore on the rising tide and finally merged with the pre‐existing berm. As the tide continued to rise, the new berm translated further onshore as an intertidal bar to the uppermost part of the foreshore. The sediment transport during the berm transition was onshore directed in the upper swash and offshore directed in the lower swash. This berm development can be described through both the neap‐berm, ridge‐and‐runnel and berm‐ridge development concepts proposed by Hine (Sedimentology 1979; 26: 333–351), and all three stages were observed during only three tidal cycles. The main factors controlling this fast transformation were the gentle slope of the cross‐shore profile, rapid water level translation rates, substantial swash overtopping of the berm, and low infiltration rates. Despite the onshore migration of intertidal bars and berm formation, no net foreshore accretion took place during the field campaign. This was largely due to the formation of rip channels with strong rip currents cutting through the intertidal bars and the berm, which acted as a sediment drain in the profile. Copyright © 2009 John Wiley & Sons, Ltd.     

Short‐term intertidal bar mobility on a ridge‐and‐runnel beach,Merlimont, northern France

Digital elevation models and topographic pro?les of a beach with intertidal bar and trough (ridge‐and‐runnel) morphology in Merlimont, northern France, were analysed in order to assess patterns of cross‐shore and longshore intertidal bar mobility. The beach exhibited a pronounced dual bar–trough system that showed cross‐shore stationarity. The bars and troughs were, however, characterized by signi?cant longshore advection of sand under the in?uence of suspension by waves and transport by strong tide‐ and wind‐driven longshore currents. Pro?le changes were due in part to the longshore migration of medium‐sized bedforms. The potential for cross‐shore bar migration appears to be mitigated by the large size of the two bars relative to incident wave energy, which is modulated by high vertical tidal excursion rates on this beach due to the large tidal range (mean spring tidal range = 8·3 m). Cross‐shore bar migration is also probably hindered by the well‐entrenched troughs which are maintained by channelled high‐energy intertidal ?ows generated by swash bores and by tidal discharge and drainage. The longshore migration of intertidal bars affecting Merlimont beach is embedded in a regional coastal sand transport pathway involving tidal and wind‐forced northward residual ?ows affecting the rectilinear northern French coast in the eastern English Channel. Copyright © 2004 John Wiley & Sons, Ltd.     

Characteristics and dynamics of multiple intertidal bars,north Lincolnshire,England

Multiple intertidal bars and troughs, often referred to as ‘ridges and runnels’, are significant features on many macrotidal sandy beaches. Along the coastline of England and Wales, they are particularly prevalent in the vicinity of estuaries, where the nearshore gradient is gentle and a large surplus of sediment is generally present. This paper examines the dynamics of such bar systems along the north Lincolnshire coast. A digital elevation model of the intertidal morphology obtained using LIDAR demonstrates that three to five intertidal bars are consistently present with a spacing of approximately 100 m. The largest and most pronounced bars (height = 0·5–0·8 m) are found around mean sea level, whereas the least developed bars (height = 0·2–0·5 m) occur in the lower intertidal zone. Annual aerial photographs of the intertidal bar morphology were inspected to try to track individual bars from year to year to derive bar migration rates; however, there is little resemblance between concurrent photographs, and ‘resetting’ of the intertidal profile occurs on an annual basis. Three‐dimensional beach surveys were conducted monthly at three locations along the north Lincolnshire coast over a one‐year period. The intertidal bar morphology responds strongly to the seasonal variation in the forcing conditions, and bars are least numerous and flattest during the more energetic winter months. Morphological changes over the monthly time scale are strongly affected by longshore sediment transport processes and the intertidal bar morphology can migrate along the beach at rates of up to 30 m per month. The behaviour of intertidal bars is complex and varies over a range of spatial and temporal scales in response to a combination of forcing factors (e.g. incident wave energy, different types of wave processes, longshore and cross‐shore sediment transport), relaxation time and morphodynamic feedback. Copyright © 2005 John Wiley & Sons, Ltd.     

Cross‐sectional profiles of sand ripples,megaripples, and dunes: a method for discriminating between formational mechanisms

Cross‐sectional profiles of sand ripples, megaripples, and sand dunes provide a useful tool for discriminating between formation by ripple and dune processes. Feature width, defined as the basal break in slope along the profile to either side of the crest, represents a good standard for comparison of profile attributes across more than three orders of magnitude. Aspect ratio (height/width) as a function of log width separates measurements into clusters representing differing mechanisms of formation. Scaling both height and distance for individual profiles by feature width facilitates comparison of profile shapes across three orders of magnitude in width. The data presented here should prove useful for evaluating possible mechanisms of origin for aeolian features observed remotely, including on planetary bodies. Copyright © 2012 John Wiley & Sons, Ltd.     

Morphological changes on meander point bars associated with flow structure at different discharges

This study investigates the impact of flow structure of different discharges on meander point bar morphology. We carried out mobile and terrestrial laser scanning campaigns before and after a flood on two sandy‐bed point bars. Between the scans, the flow structure was examined using an Acoustic Doppler Current Profiler at three flow stages. The results indicated that a meander point bar both affects and in turn, is itself modified by the flow at different discharges. The lower flow stages also have a significant effect on point bar morphology, especially on deposition over the bar head. Secondary circulation is responsible for scroll bar formation on the point bar margin beyond the apex. Flow separation at the inner bank, by contrast, does not require secondary circulation, but is dependent on flow depth over the point bar. A sudden increase in depth beyond the point bar top causes decreased stream power over the bar tail. The flow separation and decreased stream power cause a slow flow zone and net deposition over point bar tail. The backwater effect, if evident, may strengthen the process. Thus, filling over the bar tail seems generic for point bars and independent on secondary flow. Chutes and chute bars, scroll bars, bar head filling and bar platform filling, by contrast, require special fluvio‐morphological circumstances discussed in this paper. Whilst this paper confirms that the three‐dimensional flow structure has a major effect on point bar morphology, the flow structure seems to depend on how the point bar affects the flow trajectory which, in turn, depends upon the flow stage. Finally, the shape of the bend and the grain size distribution control the impacts of the flow structure, leading to divergent morphologies of point bars with certain generic features. Copyright © 2012 John Wiley & Sons, Ltd.