Masonry infill walls in reinforced concrete frames as a source of structural damping

This paper presents the results of an experimental study on the determination of damping characteristics of bare, masonry infilled, and carbon fiber reinforced polymer retrofitted infilled reinforced concrete (RC) frames. It is well known that the masonry infills are used as partitioning walls having significant effect on the damping characteristics of structures as well as contribution to the lateral stiffness and strength. The main portion of the input energy imparted to the structure during earthquakes is dissipated through hysteretic and damping energies. The equivalent damping definition is used to reflect various damping mechanisms globally. In this study, the equivalent damping ratio of carbon fiber reinforced polymer retrofitted infilled RC systems is quantified through a series of 1/3‐scaled, one‐bay, one‐story frames. Quasi‐static tests are carried out on eight specimens with two different loading patterns: one‐cycled and three‐cycled displacement histories and the pseudo‐dynamic tests performed on eight specimens for selected acceleration record scaled at three different PGA levels with two inertia mass conditions. The results of the experimental studies are evaluated in two phases: (i) equivalent damping is determined for experimentally obtained cycles from quasi‐static and pseudo‐dynamic tests; and (ii) an iterative procedure is developed on the basis of the energy balance formulation to determine the equivalent damping ratio. On the basis of the results of these evaluations, equivalent damping of levels of 5%, 12%, and 14% can be used for bare, infilled, and retrofitted infilled RC frames, respectively. Copyright © 2013 John Wiley & Sons, Ltd.     

Estimation of inelastic deformation demands in multistorey RC frame buildings

Estimation of peak inelastic deformation demands is a key component of any displacement-based procedure for earthquake-resistant design of new structures or for seismic evaluation of existing structures. On the basis of the results of over a thousand non-linear dynamic analyses, rules are developed for the estimation of mean and upper-characteristic peak inelastic interstorey drifts and member chord rotations in multistorey RC frame buildings, either bare or infilled in all storeys but the first. For bare frame structures, mean inelastic deformation demands can be estimated from a linear, equivalent static, or preferably multimodal response spectrum analysis with 5 per cent damping and with the RC members considered with their secant stiffness at yielding. 95 per cent characteristic values can be estimated as multiples of the mean deformations. For open-first-storey buildings, the linear analysis can be equivalent static, with the infills modelled as rigid bidiagonal struts and all RC members considered with their secant stiffness to yielding. Copyright © 1999 John Wiley & Sons, Ltd.     

Effect of masonry infills on seismic performance of a 3‐storey R/C frame with non‐seismic detailing

The objective of this study is to investigate the effect of masonry infills on the seismic performance of low‐rise reinforced concrete (RC) frames with non‐seismic detailing. For this purpose, a 2‐bay 3‐storey masonry‐infilled RC frame was selected and a 1 : 5 scale model was constructed according to the Korean practice of non‐seismic detailing and the similitude law. Then, a series of earthquake simulation tests and a pushover test were performed on this model. When the results of these tests are compared with those in the case of the bare frame, it can be recognized that the masonry infills contribute to the large increase in the stiffness and strength of the global structure whereas they also accompany the increase of earthquake inertia forces. The failure mode of the masonry‐infilled frame was that of shear failure due to the bed‐joint sliding of the masonry infills while that of the bare frame appeared to be the soft‐storey plastic mechanism at the first storey. However, it is judged that the masonry infills can be beneficial to the seismic performance of the structure since the amount of the increase in strength appears to be greater than that in the induced earthquake inertia forces while the deformation capacity of the global structure remains almost the same regardless of the presence of the masonry infills. Copyright © 2001 John Wiley & Sons, Ltd.     

Organic litter: dominance over stones as a source of interrill flow roughness on low‐gradient desert slopes at Fowlers Gap,arid western NSW,Australia

Thirty‐six runoff plot experiments provide data on flow depths, speeds, and Darcy–Weisbach friction coefficients (f) on bare soil surfaces, and surfaces to which were added sufficient extra plant litter or surface stones to provide projected cover of 5, 10 and 20 per cent. Precision flow depth data were derived with a computer‐controlled gantry and needle gauge for two different discharges for each plot treatment. Taking a fixed flow intensity (Reynolds number, Re = 150) for purposes of comparison shows means of f = 17·7 for bare soil surfaces, f = 11·4 for added stone treatments, and f = 23·8 for added litter treatments. Many individual values of f for stone treatments are lower than for the bare soil surface, but all litter treatments show increases in fcompared to bare soil. The lowering of f in stone treatments relates to the submerged volume that the stones occupied, and the associated concentration of flow onto a smaller part of the plot surface. This leads to locally higher flow intensities and lower frictional drag along threads of flow that the obstacles create. Litter causes higher frictional drag because the particles are smaller, and, for the same cover fraction, are 100 times more numerous and provide 20 times the edge or perimeter length. Along these edges, which in total exceed 2·5 m g^?1 (equivalent to 500 m m^?2 for a loading of 2 t ha^?1), surface tension draws up water from between the litter particles. This reduces flow depth there, and as a consequence of the lower flow intensity, frictional drag rises. Furthermore, no clear passage remains for the establishment of flow threads. These findings apply to shallow interrill flows in which litter is largely immobile. The key new result from these experiments is that under these conditions, a 20 per cent cover of organic litter can generate interrill frictional retardation that exceeds by nearly 41 per cent that of a bare soil surface, and twice that contributed by the same cover fraction of surface stones. Even greater dominance by litter can be anticipated at the many dryland sites where litter covers exceed those tested here. Copyright © 2002 John Wiley & Sons, Ltd.     

Analytical investigation of the observed damage in an RC building after March 08, 2010 Kovancilar-Turkey earthquake

Although the M _w  = 6.1 Kovancilar-Turkey earthquake of March 8, 2010 had a moderate intensity with a recorded PGA of 0.07g, it caused heavy damages in 2870 residential buildings having traditional or masonry structural systems and 42 human loss. Damage has been reported to be particularly concentrated at Kovancilar and Palu counties of Elazig province. Five hours after this earthquake, an aftershock of M _L  = 5.6 with a PGA of 0.08g struck the same region, developing the existing damages in the structures. In order to investigate this significant amount of reported damages under the effect of such low ground shakings, our reconnaissance team arrived at the region and unexpectedly came across a two-story RC building settled on a slope in Yukari Demirci village, which suffered moderate damage during the shakes. The outline of this paper can be summarized as the presentation of the results of the investigations in the order of describing the overall observed damages within the region; evaluation of the recorded motions; the details of the field-work carried out for the two story RC building and the analytical estimation of the site-assessed damages by means of nonlinear dynamic analysis. Employing the gathered data, the building is analytically modeled as plane frames and analyses are performed under the effects of the processed earthquake records, which are applied to the structure one after another in the consistent directions due to the building location. It is shown herein that the structural elements remain in the elastic range subjected to the processed recorded motions; henceforth acceleration time histories are scaled step by step up to 0.40g and computations are repeated for each acceleration level. Comparison with the observed and the analytically obtained damages confirmed that approximately 0.30g of peak ground acceleration should have to be exposed during the earthquakes.     

Non-linear dynamic earth dam–foundation interaction using a BE–FE method

A general, rigorous, coupled Boundary Element–Finite Element (BE–FE) formulation is presented for non-linear seismic soil–structure interaction in two dimensions. The BE–FE method is applied to investigate the inelastic response of earth dams to transient SV waves. The dam body, consisting of heterogeneous materials modelled with a simple non-linear hysteretic model, is discretized with finite elements, whereas the elastic half-space is discretized with boundary elements. The study focuses on the combined effects of the material non-linearity and foundation flexibility. The results show the significant effect of the foundation flexibility in reducing the response through radiation of energy. For excitations with peak ground accelerations from 0·2gto 0·6g, the crest acceleration amplification ranges from 2·5 to 1·4 and seems to be comparable with field observations and results from other studies. Deamplification increasing with strain is reported at the lower part of the dam. The method is computationally powerful and can be used for efficient non-linear analysis of complex soil–structure systems. The efficiency of the BE–FE method allows further improvements with incorporation of a more advanced constitutive model and consideration of the generation and dissipation of pore-water pressures during the earthquake. © 1998 John Wiley & Sons, Ltd.     

Local effects on RC frames induced by AAC masonry infills through FEM simulation of in-plane tests

Unreinforced masonry infills are widely used in many parts of the world and it is common practice for seismic design to use simplified methods that usually do not take into account the interaction between the infill and the structure. Starting from the 1950s, many researchers have investigated the lateral response of masonry infills focusing on several different topics. The scientific interest on masonry infills is continuously raising due to the unsatisfactory seismic response of the infilled frame structures observed during post-event inspections and to the difficulty to contrive a widely scientifically and practical recognized solution. Although some modern codes consider the presence of infills with some specifications to prevent damage in the masonry panels and global and local effects on the structure, an effective evaluation of these detrimental effects has not been achieved yet. Within this paper, a FEM simulation of in-plane pseudo-static cyclic tests on a RC frame specimen infilled with unreinforced Autoclaved Aerated Concrete (AAC) masonry infill has been performed in order to study accurately the influence and the interaction of the infill with the RC structure. The experimental results performed by Calvi and Bolognini (J Earthq Eng 5:153–185, 1999), and Penna and Calvi (Campagna sperimentale su telai in c.a. con tamponamenti in Gasbeton (AAC) con diverse soluzioni di rinforzo” (in Italian), 2006) on one-bay one-storey full scale specimens are taken as reference. Non-linear static analyses using a “meso-modelling” approach have been carried out. The masonry used in the model has been calibrated according to tests of mechanical characterization and to in-plane cyclic tests on load-bearing AAC masonry conducted by Costa et al. (J Earthq Eng 15:1–31, 2011). The analyses performed have allowed to investigate the local effects on the frame and, in particular, the changes in the moment and shear demands on the RC elements due to the presence of the AAC infill in comparison with the ones in the bare structure, and to estimate the thrust and the contact length activated by the infill on the frame.     

Pseudo‐dynamic seismic response of reinforced concrete frames infilled with non‐structural brick masonry

This paper presents pseudo‐dynamic test results on the in‐plane seismic behaviour of infilled frames. Thirteen single‐storey, single‐bay, half‐size‐scale, reinforced concrete‐frame specimens, most of which infilled with non‐structural masonry made of perforated bricks and cement mortar are tested. The infills are in contact with frames, without any connector; openings are not covered. The frames are different in their strength and details, reinforcement grade, and aspect ratio. Seismic input is the 1976 Tolmezzo (Friuli, Italy) ground acceleration, to which specimens are subjected two times: virgin and damaged by the previous test. The global seismic response of initially virgin infilled specimens considerably differs from that of bare specimens. This follows a dramatic change of properties: compared to a bare frame, the initial stiffness increases by one order of magnitude, and the peak strength more than doubles. The peak drift lessens; however, the displacement ductility demand does not. The energy demand is greater. Nevertheless, the influence of infill decreases as damage proceeds. Displacement time histories of damaged specimens are quite similar. At the local level, infill causes asymmetry and concentration of the frame deformation. Copyright © 2005 John Wiley & Sons, Ltd.     

Using palm‐mat geotextiles on an arable soil for water erosion control in the UK

To date, most studies of the effectiveness of geotextiles on soil erosion rates and processes have been conducted in laboratory experiments for less than 1 h. Hence, at Hilton (52°33′ N, 2°19′ W), UK, the effectiveness of employing palm‐mat geotextiles for soil erosion control under field conditions on arable loamy sands was investigated. Geotextile‐mats constructed from Borassus aethiopum (Borassus palm of West Africa) and Mauritia flexuosa (Buriti palm of South America) leaves are termed Borassus mats and Buriti mats, respectively. Duplicate runoff plots (10 m × 1 m on a 15° slope) had five treatments (bare, permanent grass, Borassus total plot cover, Borassus buffer strip and Buriti buffer strip). Borassus covered plots had about 72% ground cover and to differentiate between this treatment and Borassus buffer strips, the former treatment is termed Borassus completely‐covered. Runoff and eroded soil were collected from each bounded plot in a concrete gutter, leading to a receptacle. Results from 08/01/2007–23/01/2009 (total precipitation = 1776·5 mm; n = 53 time intervals) show that using Borassus buffer strips (area coverage ～10%) on bare soil decreased runoff volume by about 71% (P > 0·05) and soil erosion by 92% (P < 0·001). Bare plots had nearly 29·1 L m^?2 runoff and 2·36 kg m^?2 soil erosion during that period. Borassus buffer strip, Buriti buffer strip and Borassus completely‐covered plots had similar effects in decreasing runoff volume and soil erosion. Runoff volumes largely explain the variability in soil erosion rates. Although buffer strips of Borassus mats were as effective as whole plot cover of the same mats, the longevity of Borassus mats was nearly twice that of Buriti mats. Thus, use of Borassus mats as buffer strips on bare plots is highly effective for soil erosion control. The mechanisms explaining the effectiveness of buffer strips require further studies under varied pedo‐climatic conditions. Copyright © 2011 John Wiley & Sons, Ltd.     

填充墙RC框架结构加固方法的研究现状及展望

综述了用于提高填充墙钢筋混凝土(RC)框架结构抗震性能和改善结构损伤模式的几类加固措施,从工艺、加固效果和破坏形式3个角度进行了分析.在建筑结构设计过程中,填充墙通常被视为一种典型的脆性非均质非结构构件,忽视了填充墙与RC框架之间的相互作用.地震调查报告表明,在结构遭受地震作用时,填充墙通常先于钢筋混凝土框架发生破坏,...     

Seismic strengthening of an under‐designed RC structure with FRP

The opportunities provided by the use of fiber‐reinforced polymer (FRP) for the seismic retrofit of existing reinforced concrete (RC) structures were assessed on a full‐scale three‐story framed structure. The structure, designed only for gravity loads, was subjected to a bi‐directional pseudo‐dynamic (PsD) test at peak ground acceleration (PGA) equal to 0.20g at the ELSA Laboratory of the Joint Research Centre. The seismic deficiencies exhibited by the structure after the test were confirmed by post‐test assessment of structural seismic capacity performed by nonlinear static pushover analysis implemented on the lumped plasticity model of the structure. In order to allow the structure to withstand 0.30g PGA seismic actions, a retrofit using glass fiber‐reinforced polymer (GFRP) laminates was designed. The retrofit design was targeted to achieve a more ductile and energy dissipating global performance of the structure by increasing the ductility of columns and preventing brittle failure modes. Design assumptions and criteria along with nonlinear static pushover analysis to assess the overall capacity of the FRP‐retrofitted structure are presented and discussed. After the retrofit execution, a new series of PsD tests at both 0.20g and 0.30g PGA level were carried out. Theoretical predictions are compared with the main experimental outcomes to assess the effectiveness of the proposed retrofit technique and validate the adopted design procedures. Copyright © 2007 John Wiley & Sons, Ltd.     

Out-of-plane shaking table tests of full-scale historic adobe corner walls retrofitted with timber elements

Historic adobe structures pose a high seismic risk mainly because of the poor out-of-plane bending response of their walls that may produce fatalities and significant economic, cultural, and heritage losses. In this paper, we propose a retrofitting technique that increases the wall strength for both in-plane and out-of-plane directions. This technique consists of vertical and horizontal timber elements symmetrically installed on each face of the wall to form a confining wood frame, supplemented with vertical tensors that pre-compress the wall. This study evaluates the performance of this retrofitting technique with a two-set experimental program on full-scale historic adobe walls. On the first set, four specimens were subjected to a static overturning test with boundary conditions representing the confinement effect at both ends by orthogonal walls. On the second set, three full-scale specimens, one unretrofitted and two retrofitted, were subjected to four ground motion records on a shaking table to assess the out-of-plane dynamic behavior of typical corner walls. The unretrofitted specimen collapsed during the second motion (peak ground acceleration [PGA] = 0.39 g), while both retrofitted walls survived all four motions (maximum PGA of 0.75 g) proving the high effectiveness of the proposed retrofitting. The addition of base anchors as a variation of the retrofitting technique significantly reduced the rocking effects and the residual drifts of the system, thus improving its overall seismic performance. Further research is needed to develop guidelines for seismic retrofit of heritage buildings including multistory full-scale tests of specimens with various types of openings and retrofitting strategies that minimize their architectural impact.     

Rainfall interception by trees of Pinus radiata,and Eucalyptus viminalis,in a 1300 mm rainfall area of southeastern New South Wales: I. Gross losses and their variability

Interception loss, I, was determined by continuous concurrent measurements of the canopy precipitation balances of a mature seed orchard tree of Pinus radiata, and a dominant tree of Eucalyptus viminalis at a mountainous high rainfall site (900 m a.s.l.) in Tallaganda State Forest of the Upper Shoalhaven Catchment. Approximate canopy storage capacity (Sc) of the pine was 54 l, and that of the eucalypt was 11·3 l. Gross pine I was 26·5 per cent and eucalypt I was 8·3 per cent of total incident rainfall over a period of 18 months, from June 1975 to December 1976. The exponential model that provided the best fit to overall data relating I to gross rainfall (P_g) was of good precision for the pine (r² = 0·73) but rather poor precision for the eucalypt (r² = 0·27). A consistent pattern in interception data of the two canopy types suggested that variation in I was related to change in pervasive conditions influencing rates of evaporation from wet canopies during rainfall. Multiple regression analyses confirmed that factors such as rainfall intensity and windspeed explained some of the variation in eucalypt I but little in pine I. Negative eucalypt I and corresponding low values of pine I over a wide range of P_g (up to 20 mm) suggest that capture of wind-borne precipitation (cloud, mist, or fog) had also complicated the canopy precipitation balances.     

Concentrated flow erosion rates reduced through biological geotextiles

Soil erosion by concentrated flow can cause serious environmental damage. Erosion‐control geotextiles have considerable potential for reducing concentrated flow erosion. However, limited data are available on the erosion‐reducing potential of geotextiles. In this study, the effectiveness of three biological geotextiles in reducing soil losses during concentrated flow is investigated. Hereto, runoff was simulated in a concentrated flow flume, filled with an erodible sandy loam on three slope gradients (13·5, 27·0 and 41·5%). Treatments included three biological geotextiles (borassus, buriti and bamboo) and one bare soil surface. Darcy–Weisbach friction coefficients ranged from 0·01 to 2·84. The highest values are observed for borassus covered soil surfaces, followed by buriti, bamboo and bare soil, respectively. The friction coefficients are linearly correlated with geotextile thickness. For the specific experimental conditions of this study, borassus geotextiles reduced soil detachment rate on average to 56%, buriti geotextiles to 59% and bamboo geotextiles to 66% of the soil detachment rate for bare soil surfaces. Total flow shear stress was the hydraulic parameter best predicting soil detachment rate for bare and geotextile covered surfaces (R² = 0·75–0·84, p <0·001, n = 12–15). The highest resistance against soil detachment was observed for the borassus covered soil surfaces, followed by buriti, bamboo and bare soil surfaces, respectively. Overall, biological geotextiles are less effective in controlling concentrated flow erosion compared with interrill erosion. Copyright © 2009 John Wiley & Sons, Ltd.     

The impact of stress history on bed structure

Recent research has started to focus on how prolonged periods of sub‐threshold flows may be capable of imparting structural changes that contribute to increased bed stability. To date, this effect (termed ‘stress history’) has been found to be significant in acting to increase a bed's critical shear stress at entrainment threshold. However, it is supported by only limited, qualitative and often speculative information on the mechanisms of this stabilization process in grade‐specific studies. As such, this paper uses high resolution laser scanning to quantitatively ascertain the granular mechanics underpinning the relationship between stress history and entrainment threshold for beds of a range of grain size distributions. Employing a bed slope of 1/200, three grain size distributions with median grain sizes (D₅₀) of 4·8 mm [uniform (σ_g = (D₈₄/D₁₆)^0.5 = 1·13; bimodal (σ_g = 2·08); and, unimodal (σ_g = 1·63)] were exposed to antecedent stress histories of 60 and 960 minutes duration. Antecedent shear stress magnitude was set at 50% of the critical shear stress for the D₅₀ when no stress history period was employed. Two laser displacement scans of the bed surface (approximate area 100 mm × 117 mm) were taken, one prior to the antecedent period and one after this period, so that changes to surface topography could be quantified (resolution of x = 0·10 mm, y = 0·13 mm and z = 0·24 mm). Rearrangement of bed surface structure is described using statistical analysis and two‐dimensional (2D) semi‐variograms to analyse scaling behaviour. Results reveal vertical settlement, changes to bed roughness and particle repositioning. However, the bed grain size distribution influences the relative importance of each mechanism in determining stress history induced bed stability; this is the focus of discussion in this paper. Copyright © 2012 John Wiley & Sons, Ltd.     

Evapotranspiration from a wet temperate grassland and its sensitivity to microenvironmental variables

The eddy covariance and energy balance method was employed to determine evapotranspiration (LE) over a wet temperate C3–C4 co‐existing grassland in Japan. After sensible heat flux (H) was estimated via the eddy covariance technique, LE was calculated as the residual of the energy budget with calibration against the direct measurements of LE by a lysimeter. Daily mean LE varied from 0·8 to 10·5 MJ d⁻¹, with a peak at 16·5 MJ d⁻¹ in late July to early August. Day‐to‐day and seasonal variability in LE was affected appreciably by net radiation (R_n), atmospheric vapour pressure deficit (VPD), canopy surface conductance (g_c) and leaf area index (LAI). Before the canopy closure, LE responded to LAI in a linear manner. However, LE decreased with increasing LAI later in summer. Daytime variation in the decoupling coefficient (Ω) demonstrates that the canopy decoupled from the atmosphere in the morning and LE was primarily driven by the available energy, while in the afternoon the canopy partially coupled to the atmosphere so that LE was sensitive to VPD and g_c. Throughout the whole measurement period, Ω was generally larger than 0·5, suggesting that the available energy contributes more to LE than VPD. Copyright © 2004 John Wiley & Sons, Ltd.     

Inelastic response of RC frame buildings with seismic isolation

A comprehensive parametric study on the inelastic seismic response of seismically isolated RC frame buildings, designed for gravity loads only, is presented. Four building prototypes, with 23 m × 10 m floor plan dimensions and number of storeys ranging from 2 to 8, are considered. All the buildings present internal resistant frames in one direction only, identified as the strong direction of the building. In the orthogonal weak direction, the buildings present outer resistant frames only, with infilled masonry panels. This structural configuration is typical of many existing RC buildings, realized in Italy and other European countries in the 60s and 70s. The parametric study is based on the results of extensive nonlinear response‐time history analyses of 2‐DOF systems, using a set of seven artificial and natural seismic ground motions. In the parametric study, buildings with strength ratio (F_y/W) ranging from 0.03 to 0.15 and post‐yield stiffness ratio ranging from 0% to 6% are examined. Three different types of isolation systems are considered, that is, high damping rubber bearings, lead rubber bearings and friction pendulum bearings. The isolation systems have been designed accepting the occurrence of plastic hinges in the superstructure during the design earthquake. The nonlinear response‐time history analyses results show that structures with seismic isolation experience fewer inelastic cycles compared with fixed‐base structures. As a consequence, although limited plastic deformations can be accepted, the collapse limit state of seismically isolated structures should be based on the lateral capacity of the superstructure without significant reliance on its inherent hysteretic damping or ductility capacity. Copyright © 2012 John Wiley & Sons, Ltd.     

Performance evaluation of retrofitting strategies for non-seismically designed RC buildings using steel braces

Recent major earthquakes around the world have evidenced that research in earthquake engineering must be directed to the vulnerability assessment of existing constructions lacking appropriate seismic resisting characteristics. Their retrofit or replacement should be made in order to reduce vulnerability, and consequent risk, to currently accepted levels. In this work, the efficiency of ductile steel eccentrically-braced systems in the seismic retrofitting of existing reinforced concrete (RC) buildings is studied. The retrofit technique studied consists in a bracing system with an energy dissipation device, designed to dissipate energy by shear deformation. The numerical model was calibrated with cyclic test results on a full-scale structure. The models used for the RC frame and masonry represent their real behavior and influence in the global structural response. The steel bracing system was modeled with strut rigid elements. The model for the energy dissipater device reproduces rigorously the behavior of the shear-link observed in the cyclic tests, namely in terms of shear, drift and energy dissipation. With the calibrated numerical model, a series of non-linear dynamic analyses were performed, for different earthquake input motions, intending to study: the influence of the retrofitting system in the response of bare and infilled structures; the influence of the location and strength of the retrofitting system.     

Influence of masonry infill panels on the vibration and stiffness characteristics of R/C frame buildings

Vibration measurements were performed on two adjacent, three-storey reinforced concrete frame buildings with hollow clay brick infill panels. The first building was a bare frame and the second one was a similar frame infilled with brick panels. The fundamental period for the infilled frame building was much smaller than that of the bare frame building. Using shear beam lumped mass models and the vibration data the actual lateral stiffness of both buildings was identified. The lateral stiffness of the infilled frame building was found to be seven times that of the bare frame building. Four numerical models of the infilled frame building were constructed. The frame and floors were represented using an experimentally validated model and the infill panels by one of three commonly used ‘equivalent diagonal truss’ models or by plane stress finite elements. Only the plane stress finite element model produced a reasonable agreement with the experimental results. Copyright © 1999 John Wiley & Sons, Ltd.     

A study on the focal parameters of Shidian M =5.9 earthquake sequences in 2001

On the basis of about 300 earthquake wave forms observed in the Shidian M _S=5.9 sequences on April 12, 2001 recorded in Kunming Digital Seismic Network, the spectra of shear wave have been used to estimate the focal parameters of these earthquake sequences. The results show that within the magnitude range of 1.5–5.3, the seismic moments are 10¹⁰–10¹⁶ N·m, the corner frequencies are 0.2–0.8 Hz, radii of the focal rupture are 200–2 500 m and the stress drops are 0.1×10⁵–20×10⁵Pa. Through the statistical analyses of variation of corner frequency f _c and stress drop Δσ with time, it is discovered that the average corner frequency of the foreshock sequences is obviously lower than that of the aftershock sequences. Contrarily, the average stress drops Δσ of the foreshock sequences are clearly higher than that of the aftershocks. It is considered that these variation characteristics of average corner frequency and stress drops before and after the main shock have index significance to the precursory information before a strong earthquake. The higher stress drops for the foreshock sequences show that the higher shear stresses have been stored in the area of main shock. After the main shock, most of the stresses have been released, so the aftershock sequences show a rupture process of lower stresses. Foundation item: Scientific and Technological Key Project of Yunnan Province (2001NG46)