首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 15 毫秒
1.
微震、工程爆破等低应力循环剪切荷载作用对节理岩体工程失稳破坏具有重要影响。为研究峰前循环剪切加卸载作用下岩石节理剪切力学特性,采用RDS-200型岩石节理剪切试验系统对人工劈裂黄砂岩节理进行了峰前循环剪切下的直剪试验。通过与未进行峰前循环剪切加卸载时岩石节理力学参数预测值对比,得到峰前循环剪切加卸载作用对峰前剪切刚度、峰值剪切强度、峰值剪切位移与残余剪切强度的影响。结果表明:(1)峰前循环剪切加卸载后,当法向应力为2 MPa时,岩石节理峰前剪切刚度增大,当法向应力为4~10 MPa时,岩石节理峰前剪切刚度在循环剪切应力幅值范围内增大,在超出循环剪切应力幅值时减小;(2)峰前循环剪切加卸载后,峰值剪切强度降低了10%~20%,降低百分比随法向应力增大整体呈对数函数增大;峰值剪切位移增加了2%~40%,增加百分比随法向应力增大整体呈对数函数减小;(3)峰前循环剪切加卸载后,岩石节理残余剪切强度无明显变化,峰值剪切强度与残余剪切强度差值减小,峰后剪切应力做功损失百分比降低。  相似文献   

2.
The effect of joint overlap on the full failure behavior of a rock bridge in the shear-box test was numerically investigated by means of the particle flow code in two dimensions (PFC2D). Initially, the PFC2D was calibrated by use of data obtained from experimental laboratory tests to ensure the conformity of the simulated numerical model’s response. Furthermore, validation of the simulated models was cross-checked with the results from direct shear tests performed on non-persistent jointed physical models. By use of numerical direct shear tests, the failure process was visually observed and the failure patterns were seen to be in reasonable accordance with experimental results. Discrete element simulations demonstrated that macro shear fractures in rock bridges are because of microscopic tensile breakage of a large number of bonded discs. The failure pattern is mostly affected by joint overlap whereas the shear strength is closely related to the failure pattern. The results show that non-overlapping joints lost their loading capacity when nearly 50 % of total cracks developed within the rock bridge whereas the overlapping joints lost their loading capacity as soon as cracks initiated from the joint walls. Furthermore, progressive failure or stable crack growth was seen to develop for non-overlapped joints whereas brittle failure or unstable crack growth was seen to develop in overlapped joints.  相似文献   

3.
渗透水压对节理应力-渗流耦合特性的影响试验研究   总被引:1,自引:0,他引:1  
为研究渗透水压对节理应力-渗流耦合特性的影响,通过对6组人造节理试件恒定法向载荷和恒定法向刚度的压剪渗流试验,分析了应力和位移、节理水力开度以及透过率随剪切位移的变化趋势,获得了渗透水压对节理岩石应力-渗流耦合特性的影响规律。结果表明:节理试件的剪切应力和位移、水力开度以及透过率都与渗透水压密切相关。剪切应力随渗透水压的增大而减小,法向变形、水力开度和透过率却随渗透水压的增大而增大。在压剪渗流试验过程中,不同渗透压力的节理试件都发生了剪胀效应。研究可为深部岩体工程围岩遇水作用稳定性及渗流灾害控制技术提供科学的理论依据。  相似文献   

4.

Most natural rock masses contain a large number of random joints and fissures, and most of the rock masses at the rock engineering are commonly in both compression and shear stress environment. However, the research on the failure characteristics of complex random jointed rock mass under compressive-shear loading is still limited. To address this gap, this paper uses the particle flow code 2D to establish a discrete fractured rock mass model and carry out a series of numerical tests with different compressive-shear angles (α) and different joint geometric parameters. The effects of compressive-shear angle and joint geometric parameters on the strength and failure characteristics of fractured rock masses are studied. The results indicate that with the increase of α, the peak strength of the specimen decreases gradually, and the failure mode changes from the composite shear failure mode (Mode-I) to a plane shear failure mode (Mode-II) and then to intact shear failure mode (Mode-III). Specifically, the three failure modes occur in the specimens with α?=?15°, 30° or 45°, 60°, respectively. The existence of joints affects stress distribution on rock mass during the loading process. Furthermore, the stress at the joint tip is relatively concentrated, while on both sides of the joint is smaller. Three kinds of crack coalescence patterns are observed: tensile, shear, and tensile-shear mixed coalescence. The inclination angle of the rock bridge between adjacent joints affects the specific type of coalescence.

  相似文献   

5.
含二阶起伏体的模拟岩体节理试样剪切特性试验研究   总被引:1,自引:0,他引:1  
利用规则的小尺寸锯齿构造二阶起伏体,对不同二阶起伏体高度的人工节理进行常法向应力下的直剪试验,研究了节理剪切力学特性。对节理的剪切强度、变形特征进行了分析,并对破坏特征做出解释。试验结果表明:二阶起伏体对节理剪切力学特性有重要影响,含二阶起伏体节理的剪切力学特性与只含有一阶起伏体节理的剪切力学特性不同,只含一阶起伏体的节理剪应力只有一个峰值,含二阶起伏体的节理会出现波浪状的剪胀曲线和多峰值剪应力,且峰值剪应力随剪切位移增大依次出现并逐个减小;随着二阶起伏体高度增大,节理峰值剪切强度增大,节理依次出现磨损破坏、多次性剪断破坏、一次性剪断破坏。  相似文献   

6.
An elasto-plastic constitutive model is introduced for rock joints under cyclic loading, considering the additional shear resistance generated by the asperity damage in the first forward shear cycle and sliding mechanism for further shearing. A series of cyclic loading direct shear tests was conducted on artificial joints with triangular asperities and replicas of a real rock asperity surface under constant normal stiffness (CNS) conditions. The model was calibrated and then validated using selected data sets from the experimental results. Model simulations were found to be in good agreement with the rock joints behaviour under cyclic loading and CNS conditions both in stress prediction and dilation behaviour. In addition, dynamic stability analysis of an underground structure was carried out, using Universal Distinct Element Code and the proposed constitutive model.  相似文献   

7.
节理抗剪强度综合评价的试验研究   总被引:2,自引:0,他引:2  
选取不同吻合度自然节理试样,进行干燥状态和饱和状态的JRC-JCS模型和JRC-JMS模型试验研究。结果表明,在节理粗糙度系数的定向统计测量和尺寸效应分析,以及剪切过程衰减折减的基础上,运用JRC-JCS模型综合评价节理抗剪强度可靠性较好,考虑吻合度系数的JRC-JMC模型比JRC-JCS模型具更好的预测能力。  相似文献   

8.
相同形貌结构面重复性剪切试验和各向异性剪切试验一直是岩体结构面剪切力学特性试验研究中的难点,而该问题对于工程岩体的开挖力学响应和稳定性分析、评价与控制至关重要,问题的关键在于同一种岩石的结构面形貌的再现。为此,基于3D扫描和3D雕刻技术,重复制备了3种不同粗糙度的大理岩结构面试样,开展了不同法向应力下相同形貌结构面的各向异性剪切试验。试验结果发现:(1)同一法向应力、不同剪切方向下,相同形貌结构面的剪切强度、剪胀和剪切破坏特征均呈现明显各向异性;(2)结构面粗糙度各向异性很大程度上决定了剪切强度的各向异性,两者具有较好的正相关性;(3)随着法向应力的升高,结构面剪切特征的各向异性有逐渐弱化的趋势。同时,研究还充分表明,3D雕刻技术是系统开展结构面剪切力学特征各向异性研究的可靠手段,可在将来研究中发挥更为重要的作用。  相似文献   

9.
Constitutive laws for rock joints should be able to reproduce the fundamental mechanical behaviour of real joints, such as dilation under shear and strain softening due to surface asperity degradation. In this work, we extend the model of Plesha to include hydraulic behaviour. During shearing, the joint can experience dilation, leading to an initial increase in its permeability. Experiments have shown that the rate of increase of the permeability slows down as shearing proceeds, and, at later stages, the permeability could decrease again. The above behaviour is attributed to gouge production. The stress–strain relationship of the joint is formulated by appeal to classical theories of interface plasticity. It is shown that the parameters of the model can be estimated from the Barton–Bandis empirical coefficients; the Joint Roughness Coefficient (JRC) and the Joint Compresive strength (JSC). We further assume that gouge production is also related to the plastic work of the shear stresses, which enables the derivation of a relationship between the permeability of the joint and its mechanical aperture. The model is implemented in a finite element code (FRACON) developed by the authors for the simulation of the coupled thermal–hydraulic–mechanical behaviour of jointed rock masses. Typical laboratory experiments are simulated with the FRACON code in order to illustrate the trends predicted in the proposed model. © 1998 by John Wiley & Sons. Ltd.  相似文献   

10.
Numerical Investigations of the Dynamic Shear Behavior of Rough Rock Joints   总被引:1,自引:1,他引:0  
The dynamic shear behavior of rock joints is significant to both rock engineering and earthquake dynamics. With the discrete element method (DEM), the dynamic direct-shear tests on the rough rock joints with 3D (sinusoidal or random) surface morphologies are simulated and discussed. Evolution of the friction coefficient with the slip displacement shows that the 3D DEM joint model can accurately reproduce the initial strengthening, slip-weakening, and steady-sliding responses of real rock joints. Energy analyses show that the strengthening and weakening behavior of the rock joint are mainly attributed to the rapid accumulation and release of the elastic energy in the joint. Then, effects of the surface roughness and the normal stress on the friction coefficient and the micro shear deformation mechanisms, mainly volume change and asperity damage, of the rock joint are investigated. The results show that the peak friction coefficient increases logarithmically with the increasing surface roughness, but decreases exponentially with the increasing normal stress. In addition, the rougher rock joint exhibits both higher joint dilation and asperity degradation. However, high normal stress constrains the joint dilation, but promotes the degree of asperity degradation significantly. Lastly, the effects of the 3D surface morphology on the shear behavior of the rock joint are investigated with a directional roughness parameter. It is observed that the anisotropy of the surface roughness consequently results in the variation of the peak friction coefficient of the joint corresponding to different shearing directions as well as the micro shear deformation mechanisms, e.g., the extent of joint dilation.  相似文献   

11.
The variation of the shear strength of infilled rock joints under cyclic loading and constant normal stiffness conditions is studied. To simulate the joints, triangular asperities inclined at angles of 9.5° and 18.5° to the shear movement were cast using high-strength gypsum plaster and infilled with clayey sand. These joints were sheared cyclically under constant normal stiffness conditions. It was found that, for a particular normal stiffness, the shear strength is a function of the initial normal stress, initial asperity angle, joint surface friction angle, infill thickness, infill friction angle, loading direction and number of loading cycles. Based on the experimental results, a mathematical model is proposed to evaluate the shear strength of infilled rock joints in cyclic loading conditions. The proposed model takes into consideration different initial asperity angles, initial normal stresses and ratios of infill thickness to asperity height.  相似文献   

12.
岩石节理面形态与水力特性研究   总被引:3,自引:1,他引:3       下载免费PDF全文
通过节理面粗糙度测量、张开度模拟、节理渗流试验及有限元数值分析,探讨了岩石节理复杂的水力特性。研究表明,节理渗流具有明显的不均匀性、各向异性及与变形耦合等性质,节理的渗透系数与法向应力之间呈负指数关系。  相似文献   

13.
新型数控岩石节理剪切渗流试验台的设计与应用   总被引:2,自引:1,他引:1  
王刚  蒋宇静  王渭明  李廷春 《岩土力学》2009,30(10):3200-3209
岩石节理的应力渗流耦合性质对工程结构稳定性的影响普遍存在于各种岩体工程中,而进行岩石节理的室内剪切-渗流耦合试验,是一种有效的研究手段。采用新型数控岩体节理剪切渗流耦合试验台,应用全数字伺服控制系统,实现了对试验进程的平稳控制以及试验数据的多路同步实时采集和处理;通过剪切盒的精细设计,提高了剪切盒可承受的渗透压力值,并保证试验过程密封性能良好的同时实现了柔性边界条件。在恒定渗透压力作用下,分别进行了不同边界条件下的剪切渗流耦合试验,试验结果验证了该试验装置的可靠性和实用性,将能为岩体工程的合理设计提供有效数据依据。该试验台可以应用于地下核废料储存、水利水电地下洞室、水下隧道、采矿等工程有关问题的研究中。  相似文献   

14.
To obtain the compression–shear infiltration characteristics of joint rock, the coupled compression–shear infiltration tests of samples were carried out under different loading and boundary conditions. The shear dilatation, permeability and the change laws of hydraulic opening of jointed rockmass were obtained under different normal stiffness and loading conditions. It is shown that the contact area gradually becomes smaller and smaller with the relative sliding of two jointed surfaces. And the contact ratio is down to a minimum value when the main processes of the jointed surface reach the peak shear strength. The remaining main processes is gradually destroyed, the contact ratio of joint surface becomes larger after the main processes reaches the peak strength. The contact ratio tends to be stable until all processes were all destroyed. Due to the influence of the joint surface protrusion, the normal displacement is smaller and then increases with the increase of shear displacement. The less the stiffness of jointed rock mass is, the greater the over water area of the joint surface is, the greater the permeability is, the greater the final stability value of the hydraulic opening degree is. The theoretical basis is provided for the fractured rock mass formed of permeable channels, initiation and outbreak of permeability disaster evolution process.  相似文献   

15.
节理岩体几何结构非常复杂,研究其渗流特性对于指导含水岩层稳定性分析具有重要价值。应用离散裂隙网络模型DFN方法,基于VC++6.0软件平台,建立了平面渗流分析方法,分析了节理岩体不同几何分布情况下的渗透率张量特征,通过定义渗流定向性系数对岩体渗流的定向性特征进行了定量分析。结果表明:单组节理岩体渗流具有明显的各向异性特征,渗流定向性随着节理角度变化显著;节理随着节理贯通性增加,节理渗透率呈现对数增加趋势;两组节理情况下,各向异性特征随着节理组间夹角变化;两组节理岩体渗流特征研究中,正交分布下,岩体仍存在各向异性,但渗流定向性系数较低;当节理倾角服从正态分布时,随着节理倾角标准差增大,渗透率增加;两组节理夹角不同时,节理渗透主方向倾角随着夹角增大而相应增大,基本沿两组节理夹角方向的角平分线方向。  相似文献   

16.
17.
针对地表附近30~50 m的岩体裂隙处于一种低围压状态(约1 MPa左右)这一情况,提出了低应力状态下裂隙变形的两点假设:(1)裂隙面处于线弹性状态;(2)隙宽减小量相对于初始力学隙宽是一个微小量。结合Barton公式,建立了低法向应力下裂隙渗流的半经验理论公式,并从实验的角度验证了该公式的合理性。实验结果和理论分析表明:低法向应力作用下,裂隙渗透系数随法向应力的增加而线性降低。此外,给出了一种间接确定裂隙初始力学隙宽的方法。  相似文献   

18.
非贯通节理岩体直剪试验研究进展   总被引:1,自引:0,他引:1  
刘远明  夏才初 《岩土力学》2007,28(8):1719-1724
基于典型的直剪试验,国内外学者提出了非贯通节理岩体贯通破坏机理,并建立了相应的强度准则,如Jennings方法,即加权平均强度理论和强度准则、Lajtai岩桥破坏理论和强度准则、断裂力学的II型破坏理论和强度准则,拉剪复合破坏和强度准则。然而,非贯通节理岩体破坏机理目前还没有完全弄清楚,已建立的强度准则所包含的重要参数还需深入研究,如:如节理面的传压系数、传剪系数、弱化了的岩桥内摩擦力和内摩擦角等;非贯通节理岩体节理闭合和剪切的本构关系有待建立;不共面非贯通节理岩体全过程最大抗剪强度需进一步研究。伺服直剪试验机、静态应变测试仪、声发射仪、X射线测量等无损检测技术能够为进一步研究非贯通节理岩体的破坏机理,提出新的理论和建立新的强度准则提供强有力的技术支持。  相似文献   

19.
Particle flow code 2D (PFC2D) was adopted to simulate the shear behavior of rocklike material samples containing planar non-persistent joints. Direct shear loading was conducted to investigate the effect of joint separation on the failure behavior of rock bridges. Initially calibration of PFC was undertaken with respect to the data obtained from experimental laboratory tests to ensure the conformity of the simulated numerical models response. Furthermore, validation of the simulated models were cross checked with the results of direct shear tests performed on non-persistent jointed physical models. Through numerical direct shear tests, the failure process was visually observed, and the failure patterns were found reasonably similar to the experimentally observed trends. The discrete element simulations demonstrated that the macro-scale shear zone resulted from the progressive failure of the tension-induced micro-cracks. The failure pattern was mostly influenced by joint separation, while the shear strength was linked to the failure pattern and failure mechanism. Furthermore, it was observed that the failure zone is relatively narrow and has a symmetrical pattern when rock bridges occupy a low percentage of the total shear surface. This may be due to the high stress interactions between the subsequent joints separated by a rock bridge. In contrast, when rock bridges are occupying sufficient area prohibiting the stress interactions to occur then the rupture of surface is more complex and turns into a shear zone. This zone was observed to be relatively thick with an unsymmetrical pattern. The shear strength of rock bridges is reduced by increasing the joint length as a result of increasing both the stress concentration at tip of the joints and the stress interaction between the joints.  相似文献   

20.
Study of rock joints under cyclic loading conditions   总被引:11,自引:3,他引:11  
Summary A conceptual model for the behaviour of rock joints during cyclic shear and under constant normal stresses was proposed according to results from shear tests with 50 concrete replicas of rock joints. The shear strength and deformability of joint samples were found to be both anisotropic and stress dependent. Based on these experimental results, a two-dimensional constitutive model was developed for rock joints undergoing monotonic or cyclic loading sequences. The joint model was formulated in the framework of non-associated plasticity, coupled with empirical relations representing the surface roughness degradation, appearance of peak and residual shear stresses, different rates of dilatancy and contraction, variable normal stiffness with normal deformation, and dependence of shear strength and deformability on the normal stress. The second law of thermodynamics was represented by an inequality and used to restrict the values of some of the material parameters in the joint model. The new joint model was implemented into a two-dimensional Distinct Element Method Code, UDEC, and its predictions agreed well with some well-known test results.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号