沙牌坝址基岩场地地震动输入参数研究

重大水利水电工程地震动输入参数必须根据专门的地震危险性分析结果来确定。目前由地震危险性分析得到的一致概率反应谱具有包络的意义,不能反映实际地震的频谱特性,输入“一致概率反应谱”可能导致地震作用偏大;拟合设计反应谱人工生成地震动加速度时程的频率非平稳性也没有得到很好解决。为了解决这些问题,得到与坝址地震危险性一致、具体地震的输入参数,结合沙牌大坝提出了一套适用于重大水利水电工程基岩场地地震动输入参数确定方法：通过以有效峰值加速度为参数的概率地震危险性计算分析,确定坝址不同超越概率下的有效峰值加速度及对坝址贡献最大的潜在震源区;在最大贡献潜在震源内利用震级空间联合分布概率最大法确定坝址设定地震,依据加速度反应谱衰减关系确定与坝址设定地震对应的设计反应谱;根据设定地震结果和时变功率谱模型参数衰减关系确定时变功率谱,将时变功率谱和最小相位谱按三角级数叠加法进行强度和频率非平稳地震加速度时程合成。在对沙牌坝址区域的地震活动性及地震构造环境分析评价的基础上,采用上述方法,得到了坝址基岩场地不同超越概率下的有效峰值加速度、设计反应谱、强度和频率非平稳地震加速度时程等地震动输入参数。     

地铁抗震设防水准的研究及北京地铁工程典型地段地震小区划

地铁作为人口密集且遭受地震破坏后难以修复的重要生命线工程,如何确保其地震安全具有越来越重要的意义。本文将以北京具有典型意义的地铁线路北京地铁五号线作为研究目标,在对沿线地震、地质条件分析的基础上,通过分析研究在不同场地条件、不同风险水平和不同深度条件下的地震动参数和反应谱变化规律,确定了地铁工程的抗震设防概率风险水平为50 a超越概率63%、10%、2%,设计地震动参数取地表计算值。并通过北京地铁五号线工程地震小区划及分区反应谱特征研究,确定北京地铁五号线工程的抗震设防要求。     

宁波地区地震危险性分析简述

本文论述了宁波盆地附近区域构造的活动性及其对宁波地区地震的影响，并通过对该区历史地震的时空分析划分了潜在震源区，确定了地震活动参数。采用地震点源扩散模型计算了宁波市的地震危险性，得到了地震烈度和峰值加速度的超越概率。从而由地质构造活动性和地震活动性两方面评估了宁波地区的地震危险性。可作为各类工程建设规划参考。     

敦煌莫高窟潜在地震变形数值模拟

在研究莫高窟地区地震地质条件及潜在地震危险性分析的基础上,基于地震的断层弹性位错理论,采用位移水平分布的抛物线模型,假定三危山断层分别发生5.5、6.0和6.5级地震情况下,用三维有限元的方法分析计算了莫高窟地区的潜在地震变形。给出了在震级5.5、6.0及6.5级三种情况断层逆冲和水平走滑两种活动方式下,莫高窟区的地震位移和应变值,供石窟的抗震设防加固设计参考。     

大连开发区场地地震设计参数

根据工作区潜在震源区划分、潜在震源区地震活动性参数和地震动衰减关系, 进行场地地震危险性分析, 得到不同概率水平下场区相应地震烈度和基岩水平加速度峰值及其反应谱。根据场地工程地震条件划分不同地质单元及相应的场地类别, 进行不同概率水平的地震反应分析计算, 确定地震动设计参数。     

基于Newmark模型的概率地震滑坡危险性模型参数优化与应用:以鲁甸地震区为例

应用概率地震危险性评价模型进行地震滑坡危险性区划,是解决潜在地震诱发滑坡危险性评价中震源不确定性与诱发滑坡时空不确定性的有效方法 .通过理论分析,结合鲁甸地震区的实际情况,对基于力学原理的Newmark滑块位移模型与概率地震滑坡危险性分析方法中的参数的不确定性问题进行了分析,将斜坡岩土体地震作用下的强度衰减效应、地震加速度地形放大效应、断层破碎带效应融合到了斜坡累积位移计算模型中,进行了模型计算参数的优化.改进后的分析模型,更好地反映了高陡斜坡地形与断层破碎带对地震滑坡灾害发育的控制作用,在鲁甸地震区域滑坡应用中,优化模型中的滑坡失稳极高风险区与实际地震滑坡分布表现出了较好的一致性,在超越概率2%的滑坡失稳概率分布中,鲁甸地区包谷垴-小河断裂、鲁甸-昭通断裂带及牛栏江河谷地带地震滑坡高-极高风险区分布面积增幅十分显著.因此,在Newmark滑块位移模型中考虑地震动参数与岩土参数动态响应规律与变量间的定量关系,对于提高区域斜坡稳定性分析的可靠性具有重要意义.     

武汉地区地震效应影响研究

虽然武汉市地震影响及地震危险性的水平较低 ,强震也不是武汉市工程地质环境的主要问题 ,但在城市生命线工程和高层超高层建筑方面必须考虑单体抗震设防。而且 ,随着武汉市城市建设的不断发展 ,地震效应影响逐渐成为武汉市工程地质环境评价的一个重要因子。文章在分析了武汉地区地震动衰减规律 ,进行了地震危险性评价 ,深入研究了各土层动力参数性质的基础上 ,指出武汉地区地震地面破坏主要存在砂土液化和软土震陷两种型式及各自可能的空间分布.     

某电力扩建场地工程地震条件分析

本文采用工程抗震理论,结合场地实际状况,论述了某电力扩建场地的区域构造条件和区域地震环境,确定了场地的地震动参数,并采用概率地震危险性分析法对扩建场地进行地震危险性分析,从而为该工程建设提供合理的设计依据.     

边坡地震稳定性分析的荷载增强分析方法

岩土边坡地震稳定性分析是岩土工程和地震工程研究的重要课题之一,本文明确区别了两种不同意义的边坡地震稳定性概念:一是按一定的抗震设防地震作用考虑,边坡现状强度与边坡强度退化到发生地震破坏时的临界强度相比较而言的储备强度稳定性;二是对于一定的边坡强度状态,使边坡发生动力破坏的地震作用与设防地震作用相比较而言的地震动力超载稳定性。考虑边坡强度退化的边坡稳定性概念已经得到普遍采用,分析方法较为熟知;而按动力超载考虑的边坡地震稳定性概念以往几乎没有提及,边坡稳定性判别标准和分析方法尚有待探讨。本文主要针对第二种边坡地震稳定性地震动力超载稳定性的衡量标准和分析方法进行了研究,提出了边坡地震动力超载稳定性评判的临界地震峰值加速度准则,并提出了边坡地震动力超载稳定性分析的荷载增强法:针对边坡的现状强度状态,由小到大逐渐增加地震作用的强度,搜索导致边坡失稳的临界地震峰值加速度,最后根据边坡临界地震峰值加速度与边坡所在区域的设防地震峰值加速度比较情况确定边坡的地震稳定性。论文采用荷载增强法对中国陕西宝鸡蟠龙塬黄土边坡地震动力超载稳定性进行了分析。结果表明,针对宝鸡地区未来50a超越概率为10%的地震动作用,该边坡具有较高的地震动力超载稳定性。     

基于地面运动强度及标准贯入试验的上海地区砂土地震液化评价

上海市地处长江三角洲前缘,黄浦江和苏州河交汇区域,特殊的地理环境与沉积环境导致浅部砂层广泛发育。随着城市建设的不断推进,上海城市区域范围的砂土地震液化风险评价成为亟待研究的课题。文章基于上海市工程钻孔数据,结合地震地面运动加速度分布与标准贯入试验,建立区域性地震液化危险性评价模型,对上海市进行了地震液化危险性评价。研究认为当发生50年超越概率10%的地震条件下,上海市陆域面积的66.0%将不会产生地震砂土液化灾害,21.8%的陆域面积仅发生轻微液化,只有崇明、横沙、长兴三岛,黄浦江及苏州河两岸地震液化等级达到中等甚至严重,占全市陆域面积12.3%;50年超越概率2%的地震条件下,随着峰值地面运动加速度整体升高,全市范围内轻微—严重液化区域明显增多,可能发生地震液化的总面积达到全市陆域面积46.25%。上海市存在砂土地震液化的危险性,但是发生概率较低。研究认为,目前的抗震设计规范中上海市的设防烈度偏高,可能导致不必要的建设成本。同时研究中的不同超越概率下的地震液化危险性评价结果为上海市工程建设相关标准的合理化改进的提供了建议和参考。      

基于简化 Newmark位移模型的区域地震滑坡危险性快速评估以汶川MS 8.0级地震为例

以汶川MS8.0级地震重灾区的11县市为例,初步提出了基于简化Newmark位移模型的地震滑坡危险性应急快速评估方法。利用汶川地震即时地震动参数、工程地质岩性经验分组及地形坡度数据,借助ArcGIS空间数据建模工具编制了地震滑坡危险性快速评估流程模块。计算了区域浅表层饱和岩土体斜坡的静态安全系数Fs、临界加速度ac,并借此分析了地震滑坡易发性。利用经验式获得了汶川地震Arias强度和区域滑坡位移DN分布,实现了汶川地震重灾区地震滑坡危险性的快速评估,为应急救灾决策提供了参考。通过对比评估结果和震后滑坡调查成果,可知数十处灾难性滑坡绝大部分位于-高危险区的龙门山主中央断裂带两侧约20km地带中,显示了评估方法的可靠性; 同时,分析指出了空间数据精度及更新不足导致局部评估结果欠佳的局限性,并提出了改进建议。     

Seismic Hazard Assessment at Esfaraen‒Bojnurd Railway,North‒East of Iran

The objective of this study is to evaluate the seismic hazard at the Esfarayen-Bojnurd railway using the probabilistic seismic hazard assessment (PSHA) method. This method was carried out based on a recent data set to take into account the historic seismicity and updated instrumental seismicity. A homogenous earthquake catalogue was compiled and a proposed seismic sources model was presented. Attenuation equations that recently recommended by experts and developed based upon earthquake data obtained from tectonic environments similar to those in and around the studied area were weighted and used for assessment of seismic hazard in the frame of logic tree approach. Considering a grid of 1.2 × 1.2 km covering the study area, ground acceleration for every node was calculated. Hazard maps at bedrock conditions were produced for peak ground acceleration, in addition to return periods of 74, 475 and 2475 years.     

基于震害统计的城市地下空间地震安全性评价

建筑物的地震安全性是城市规划和建设过程首先要回答的问题。我国城市地震安全性评价的方法理论多针对地上建筑物,而对地下空间的地震安全性研究较为薄弱,严重滞后于城市发展对地下空间的需求。活断层是诱发地震、导致建筑物破坏的的直接因素。考虑到空间关系上,地下空间与断层之间的交互关系为相交或相离。因此,本文将地下空间分为两类:与断层相交的地下空间称为跨断层地下空间,远离断层的地下空间称为远离断层地下空间。本文尝试将断裂带同震地表破裂、地震峰值加速度、地震烈度等地表地震安全性评价考量的要素与地下空间埋藏深度建立联系,并在此基础上总结基于震害统计的地下空间地震安全性评价方法。最后,本文选取地下空间利用需求较高的深圳和北京地区为实例进行介绍。     

PSHA of Van province for performance assessment using spectrally matched strong ground motion records

Within the framework of the performance based earthquake engineering, site specific earthquake spectra for Van province has been obtained. It is noteworthy that, in probabilistic seismic hazard assessment, as a first stage data from geological studies and records from the instrumental period were compiled to make a seismic source characterization for the study region. The probabilistic seismic hazard curves were developed based on selected appropriate attenuation relationships, at rock sites, with a probability of exceedance 2, 10 and 50% in 50 yrs period. The obtained results are compared with the spectral responses proposed for seismic evaluation and retrofit of building structure in Turkish Earthquake Code (2007), section 7. The acceleration response spectrums obtained from probabilistic seismic hazard analysis are matched to adjust earthquake accelerograms recorded during the 2011 Van earthquakes by using SeismoMatch v2.0 software. The aim of this procedure is to obtain a set of reasonable earthquake input motions for the seismic evaluation of existing buildings.     

地震滑坡危险性概念和基于力学模型的评估方法探讨

在我国大陆地区运用基于力学模型的Newmark位移分析方法开展地震滑坡危险性定量评估,尚处在起步阶段.为了进一步明确地震滑坡危险性概念和改进推广基于力学模型的评估方法,首先阐明了狭义的地震滑坡危险性预测评估与震后反演评估的关系; 同时为了应对地震应急、震后重建及潜在地震条件下的不同评估需求,初步提出了广义的地震滑坡危险性评估框架.随后申述了基于Newmark位移分析的地震滑坡危险性评估方法的理论基础、方法分类及最新进展,并以汶川地震滑坡危险性快速评估为例,剖析了目前影响评估有效性的不确定性及空间数据质量等问题,指出了基于力学模型的地震滑坡危险性评估方法的改进方向.建议开展潜在地震及其诱发滑坡危险性的耦合评估,建立适用于我国大陆地区地震滑坡位移分析的经验模型,以便为国家层面的地震滑坡危险性区划服务.     

Tectonic stress,seismicity, and seismic hazard in the southeastern Carpathians

Intermediate-depth earthquakes in the Vrancea region occur in response to stress generation due to descending lithosphere beneath the southeastern Carpathians. In this article, tectonic stress and seismicity are analyzed in the region on the basis of a vast body of observations. We show a correlation between the location of intermediate-depth earthquakes and the predicted localization of maximum shear stress in the lithosphere. A probabilistic seismic hazard assessment (PSHA) for the region is presented in terms of various ground motion parameters on the utilization of Fourier amplitude spectra used in engineering practice and risk assessment (peak ground acceleration, response spectra amplitude, and seismic intensity). We review the PSHA carried out in the region, and present new PSHA results for the eastern and southern parts of Romania. Our seismic hazard assessment is based on the information about the features of earthquake ground motion excitation, seismic wave propagation (attenuation), and site effect in the region. Spectral models and characteristics of site-response on earthquake ground motions are obtained from the regional ground motion data including several hundred records of small and large earthquakes. Results of the probabilistic seismic hazard assessment are consistent with the features of observed earthquake effects in the southeastern Carpathians and show that geological factors play an important part in the distribution of the earthquake ground motion parameters.     

Seismic Hazard and Risk Assessment for Tulbagh,South Africa: Part I – Assessment of Seismic Hazard

In this part of our study the probabilistic seismic hazard analysis (PSHA) for Tulbagh was performed. The applied procedure is parametric and consists essentially of two steps. The first step is applicable to the area in the vicinity of Tulbagh and requires an estimation of the area-specific parameters, which, in this case, is the mean seismic activity rate, , the Gutenberg-Richter parameter, b, and the maximum regional magnitude, m_max. The second step is applicable to the Tulbagh site, and consists of parameters of distribution of amplitude of the selected ground motion parameter. The current application of the procedure provides an assessment of the PSHA in terms of peak ground acceleration (PGA) and spectral acceleration (SA). The procedure permits the combination of both historical and instrumental data. The historical part of the catalogue only contains the strongest events, whereas the complete part can be divided into several subcatalogues, each assumed complete above a specified threshold of magnitude. In the analysis, the uncertainty in the determination of the earthquake was taken into account by incorporation of the concept of `apparent magnitude'. The PSHA technique has been developed specifically for the estimation of seismic hazard at individual sites without the subjective judgement involved in the definition of seismic source zones, when the specific active faults have not been mapped or identified, and where the causes of seismicity are not well understood. The results of the hazard assessment are expressed as probabilities that specified values of PGA will be exceeded during the chosen time intervals, and similarly for the spectral accelerations. A worst case scenario sketches the possibility of a maximum PGA of 0.30g. The results of the hazard assessment can be used as input to a seismic risk assessment.     

Ground motion studies for microzonation in Iran

An important step in effectively reducing seismic risk and the vulnerability of a city located in an earthquake prone area is to conduct a ground motion microzonation study for the desired return period. The International Institute of Earthquake Engineering and Seismology (IIEES) initiated a number of seismic microzonation projects for Iran. This paper presents the steps followed by IIEES in ground motion microzonation. IIEES performs both probabilistic and deterministic seismic hazard analysis. IIEES uses his own fault map for seismotectonic studies and develops modulus and damping curves for the soils in the study area. The experience of ground motion microzonation shows that in almost all cases, the estimated 475-year peak ground acceleration (PGA) values are higher than the PGA proposed by the Iranian seismic code. Although ground motion microzonation in Iran has some shortcomings, IIEES is making new improvement. This includes development in deterministic seismic hazard analysis, two-dimensional and three-dimensional modelling of basin and topographical effects, using microtremor measurements to find shear-wave velocity profiles in high-density urban areas and providing maps for spectral acceleration in the study area.     

Comprehensive seismic hazard assessment of Tripura and Mizoram states

Northeast India is one of the most highly seismically active regions in the world with more than seven earthquakes on an average per year of magnitude 5.0 and above. Reliable seismic hazard assessment could provide the necessary design inputs for earthquake resistant design of structures in this region. In this study, deterministic as well as probabilistic methods have been attempted for seismic hazard assessment of Tripura and Mizoram states at bedrock level condition. An updated earthquake catalogue was collected from various national and international seismological agencies for the period from 1731 to 2011. The homogenization, declustering and data completeness analysis of events have been carried out before hazard evaluation. Seismicity parameters have been estimated using G–R relationship for each source zone. Based on the seismicity, tectonic features and fault rupture mechanism, this region was divided into six major subzones. Region specific correlations were used for magnitude conversion for homogenization of earthquake size. Ground motion equations (Atkinson and Boore 2003; Gupta 2010) were validated with the observed PGA (peak ground acceleration) values before use in the hazard evaluation. In this study, the hazard is estimated using linear sources, identified in and around the study area. Results are presented in the form of PGA using both DSHA (deterministic seismic hazard analysis) and PSHA (probabilistic seismic hazard analysis) with 2 and 10% probability of exceedance in 50 years, and spectral acceleration (T = 0. 2 s, 1.0 s) for both the states (2% probability of exceedance in 50 years). The results are important to provide inputs for planning risk reduction strategies, for developing risk acceptance criteria and financial analysis for possible damages in the study area with a comprehensive analysis and higher resolution hazard mapping.     

Assessment of seismic hazard and liquefaction potential of Gujarat based on probabilistic approaches

Gujarat is one of the fastest-growing states of India with high industrial activities coming up in major cities of the state. It is indispensable to analyse seismic hazard as the region is considered to be most seismically active in stable continental region of India. The Bhuj earthquake of 2001 has caused extensive damage in terms of causality and economic loss. In the present study, the seismic hazard of Gujarat evaluated using a probabilistic approach with the use of logic tree framework that minimizes the uncertainties in hazard assessment. The peak horizontal acceleration (PHA) and spectral acceleration (Sa) values were evaluated for 10 and 2?% probability of exceedance in 50?years. Two important geotechnical effects of earthquakes, site amplification and liquefaction, are also evaluated, considering site characterization based on site classes. The liquefaction return period for the entire state of Gujarat is evaluated using a performance-based approach. The maps of PHA and PGA values prepared in this study are very useful for seismic hazard mitigation of the region in future.