基于柱顶隔震的3层3跨地铁地下车站结构抗震性能研究

针对3层3跨框架式地铁地下车站结构抗震薄弱构件,采用在柱顶不同位置设置铅芯橡胶隔震支座的方法,建立土-地下连续墙-主体结构非线性静动力耦合相互作用的二维整体时域有限元分析模型,分析柱顶隔震支座对车站主体结构的侧向变形、地震损伤和动应力反应等结构地震反应特性的影响.结果表明,仅在抗震薄弱的顶层和底层中柱柱顶设置2层隔震支...     

隔震防倒塌支座及楼梯间位置对框架结构抗震性能的影响研究

为研究梯段板下端设置隔震防倒塌支座和楼梯间位置对钢筋混凝土框架结构抗震性能的影响,利用ETABS软件建立不包括、包括隔震防倒塌支座的3种楼梯间布置方案,6个框架结构计算模型。通过模态分析、反应谱分析和Pushover分析,研究隔震防倒塌支座和楼梯间位置对框架结构的振型、内力及破坏机制的影响。结果表明:梯段板下端设置隔震防倒塌支座后,楼梯间位置对钢筋混凝土框架结构的扭转效应影响较小,且框架结构在两个主轴方向的动力特性比较接近;楼梯间框架柱内力均显著降低,但楼梯间布置在最边跨时,在垂直于梯跑方向地震作用下,框架结构边柱内力较大;框架梁对整体框架结构的耗能贡献较多,增强了框架结构的抗震性能,大震时楼梯构件严重破坏较晚,设置隔震防倒塌支座可保证楼梯整体稳定性。     

高层分段隔震结构的动力响应分析

本文提出了一种基于叠层橡胶支座的大高宽比高层建筑分段隔震结构形式,并对同一高层建筑结构分别采用基础隔震、层间隔震和分段隔震三种不同形式时进行了数值模拟对比分析。结果表明,采用分段隔震形式可明显减小高层建筑结构的顶层侧向位移、中间隔震层的相对位移和下支柱端应力,使结构的侧向位移集中于两个隔震层上,耗散了大部分地震输入能量,保障了与隔震层相连的构件的安全性,防止了由于支座受拉或剪压破坏导致上部结构倾覆倒塌现象的发生。     

基于汶川地震的LRB与RB隔震连续梁桥地震响应对比研究

为了研究铅芯橡胶支座(LRB)和板式橡胶支座(RB)对连续梁桥地震响应及隔震效果的影响,分别采用Bouc - Wen滞回恢复力模型模拟LRB的力-位移非线性特性,采用直线型恢复力模型模拟RB的本构关系,通过结构离散建立了非隔震、LRB隔震和RB隔震3种连续梁桥的有限元计算模型,运用四阶显式Runge - Kutta迭代法和Newmark时间积分法联合求解增量形式的全桥动力微分方程,并结合算例对3种连续梁桥有限元计算模型分别输入汶川地震波进行非线性时程对比分析.结果表明:LRB在控制梁体与支座位移,降低结构加速度和墩、台底内力响应方面均比RB的效果要显著;采用RB隔震后,梁体与支座的位移响应均较大,在桥梁隔震设计时要予以充分重视.     

Seismic performance of two-story subway station structures with different isolating systems

When the sliding bearing is fixed only at the top of the middle column of the underground structure, the cracks at the side end of the middle plate should be aggravated while the seismic damage of the mid-column should be alleviated. To enhance the seismic performance of the mid-plate, a new isolation design method has been mentioned while the elastic sliding bearings are set at the top of the mid-columns and between the side end of the mid-plate and the side wall at the same time. By establishing a nonlinear finite element analysis model for the static-dynamic coupling interaction system, the seismic response characteristics of the cast-in-place station structure without a sliding bearing have been analyzed and compared with those of the station structure with the sliding bearing fixed only at the top of the middle columns, and those of the station structure with sliding bearing be fixed between the mid-plate and the sidewall at the same time. The results show that the new isolation station structures suffer fewer earthquake damages at the mid-plate and mid-columns at the same time, which can improve the overall seismic performance of the subway station structure.     

Convex model-based calculation of robust seismic fragility curves of isolated continuous girder bridge

The convex model approach is applied to derive the robust seismic fragility curves of a five-span isolated continuous girder bridge with lead rubber bearings (LRB) in China. The uncertainty of structure parameters (the yield force and the post-yield stiffness of LRB, the yield strength of steel bars, etc.) are considered in the convex model, and the uncertainty of earthquake ground motions is also taken into account by selecting 40 earthquake excitations of peak ground acceleration magnitudes ranging from 0.125 to 1.126 g. A 3-D finite element model is employed using the software package OpenSees by considering the nonlinearity in the bridge piers and the isolation bearings. Section ductility of piers and shearing strain isolation bearings are treated as damage indices. The cloud method and convex model approach are used to construct the seismic fragility curves of the bridge components (LRB and bridge piers) and the bridge system, respectively. The numerical results indicate that seismic fragility of the bridge system and bridge components will be underestimated without considering the uncertainty of structural parameters. Therefore, the failure probability P _f,max had better be served as the seismic fragility, especially, the fragility of the bridge system is largely dictated by the fragility of LRB. Finally, the probabilistic seismic performance evaluation of the bridge is carried out according to the structural seismic risk estimate method.     

Multiple‐slider surfaces bearing for seismic retrofitting of frame structures with soft first stories

A new isolation interface is proposed in this study to retrofit existing buildings with inadequate soft stories as well as new structures to be constructed with soft first story intended for architectural or functional purposes. The seismic interface is an assembly of bearings set in parallel on the top of the first story columns: the multiple‐slider bearings and rubber bearings. The multiple‐slider bearing is a simple sliding device consisting of one horizontal and two inclined plane sliding surfaces based on polytetrafluoroethylene and highly polished stainless steel interface at both ends set in series. A numerical example of a five‐story reinforced concrete shear frame with soft first story is considered and analyzed to demonstrate the efficiency of the proposed isolation system in reducing the ductility demand and damage in the structure while maintaining the superstructure above the bearings to behave nearly in the elastic range with controlled bearing displacement. Comparative study with the conventional system as well as various isolation systems such as rubber bearing interface and resilient sliding isolation is carried out. Moreover, an optimum design procedure for the multiple‐slider bearing is proposed through the trade‐off between the maximum bearing displacement and the first story ductility demand ratio. The results of extensive numerical analysis verify the effectiveness of the multiple‐slider bearing in minimizing the damage from earthquake and protecting the soft first story from excessively large ductility demand. Copyright © 2012 John Wiley & Sons, Ltd.     

隔震与非隔震支座对混凝土箱梁桥地震易损性的影响

为评估隔震和非隔震支座对桥梁地震易损性的影响,以一座3跨连续混凝土箱梁桥为分析对象,首先建立采用铅芯橡胶隔震支座与非隔震型盆式橡胶支座下桥梁的数值模型,求得不同程度地震作用下墩顶与支座的最大位移响应;再定义转角延性比损伤指标,结合支座剪应变,分析桥墩和支座的地震易损性情况;最后通过宽界限法建立全桥地震易损性曲线。研究结果表明,支座是较容易发生损坏的构件,而桥梁系统比桥墩或支座更易发生破坏,同时铅芯橡胶支座的破坏概率明显低于非隔震型盆式支座,可见采用隔震支座能有效减小桥墩墩顶在地震作用下的最大位移,此时桥墩地震易损性优于采用非隔震支座的情况。     

Three-dimensional seismic isolation bearing and its application in long span hangars

Based on the seismic response characteristics of space frame structures,a new type of seismic isolation bearing defined as a three-dimensional seismic isolation bearing(3DSIB) is developed in this paper.The bearing offers excellent properties such as multi-dimensional seismic isolation,reasonable rotation capability,good ability to resist lifting load,uncoupled stiffness in horizontal and vertical directions,etc.In the 3DSIB,the horizontal dimension is designed by combining the Teflon sliding device and helical spring,while the vertical dimension is developed by introducing disk springs or helical springs.The mathematical model of the 3DSIB was established and its performance with the critical parameters was tested on a shaking table.Furthermore,the 3DSIB was applied in a 120 m span hangar structure and simulated using SAP2000 software to evaluate its performance in practical structures.The performance of the structures with and without 3DSIB was compared.It is shown that the hangar structure with 3D bearings achieves a better performance.The axial force and acceleration response of the structures with 3DSIB are effectively reduced,while the displacement response of the bearing is within the predetermined range.     

楼板及其配筋在RC框架结构实现抗震延性机制中的作用分析

总结采用梁有效翼缘来考虑楼板及配筋对“强柱弱梁”机制形成的影响的实验和数值仿真研究。基于SAP2000采用三种侧向加载模式对RC框架结构不带楼板、不带楼板考虑梁刚度放大、带楼板的三个模型进行pushover分析,对力与位移的关系曲线、塑性铰的出铰顺序以及顶点位移与层间位移等方面进行探讨。结果表明:三个模型的“强柱弱梁”现象不带楼板的纯框架结构最明显,考虑梁刚度放大的模型次之,带楼板结构最不明显,证明负弯矩承载力和刚度等反映“强柱弱梁”的参数及塑性铰的出现顺序与楼板、板内配筋存在明显的对应关系;楼板及配筋影响框架结构的整体变形性能和塑性耗能能力,是抗震延性机制实现的重要影响因素。在后续的结构设计中,建议考虑实际楼板和钢筋建模进行计算分析。     

Strain field measurements of rubber by image analysis and design criteria for laminated rubber bearings (LRB)

Although seismic isolation rubber bearings in bridges and buildings have proven to be a very effective passive method for reducing earthquake‐induced forces, a detailed mechanical modeling of the rubber that is used in bearings under large strains has not been established. Therefore, a 3D model of failure behavior and the design criteria for the safety evaluation of seismic isolation bearings have not yet been developed. This paper presents: (1) correlation‐based template‐matching algorithms to measure large strain fields of continua; (2) a failure criterion for rubber; and (3) the design criteria for the safety evaluation of laminated algorithms, data‐validation algorithms were developed and implemented to eliminate possible unrealistic displacement vectors present in the measured displacement field. The algorithms were successfully employed in the strain field measurement of LRB and rubber materials that are subjected to failure. The measured local strains for rubber material at failure were used to develop a failure criterion for rubber. The validity of the proposed criterion was evaluated by applying it to the LRB; the criterion was introduced into a 3D finite element model of LRB, compared with the experimental results of bearings failure, and verified. Finally, design criteria are proposed for LRB for the safety evaluation. Copyright © 2003 John Wiley & Sons, Ltd.     

屈曲约束支撑钢框架结构影响因素的静力弹塑性分析

为检验抗侧刚度比和支撑布置方式等因素对具有不同总层数的屈曲约束支撑钢框架的抗震性能影响,借助SAP2000软件,探讨6层、12层、18层屈曲约束支撑钢框架结构在抗侧刚度比分别为1、2、3、4、5共五种工况及倒V型和单斜向两种支撑布置方式下的抗震性能。结果表明,屈曲约束支撑钢框架结构基底剪力-顶点位移曲线呈典型的双线性特征;随抗侧刚度比的增大,结构的层间位移角总体上呈降低趋势,基底剪力及支撑轴力增大,顶点水平位移变小,框架所分担的剪力降低;倒V型布置支撑较单斜向布置具有略大的基底剪力、谱加速度,较小的顶点位移、层位移、层间剪力和框架剪力分担率。分析表明,总体上来看,倒V型布置较单斜向布置时支撑框架结构具有略优的抗震性能;抗侧刚度比较支撑布置方式对支撑框架结构抗震性能的影响更为显著。     

Spherical sliding isolation bearings with adaptive behavior: Theory

The principles of operation and force–displacement relationships of three novel spherical sliding isolation bearings are developed in this paper. These bearings are completely passive devices, yet exhibit adaptive stiffness and adaptive damping. That is, the stiffness and damping change to predictable values at calculable and controllable displacement amplitudes. The primary benefit of adaptive behavior is that a given isolation system can be separately optimized for multiple performance objectives and/or multiple levels of ground shaking. With the devices presented here, this is accomplished using technology that is inherently no more complex than what is currently used by the civil engineering profession. The internal construction consists of various concave surfaces and behavior is dictated by the different combinations of surfaces upon which sliding can occur over the course of motion. As the surfaces upon which sliding occurs change, the stiffness and effective friction change accordingly. A methodology is presented for determining which surfaces are active at any given time based on the effective radius of curvature, coefficient of friction and displacement capacity of each sliding surface. The force–displacement relationships and relevant parameters of interest are subsequently derived based on the first principles. Copyright © 2007 John Wiley & Sons, Ltd.     

设置负刚度装置的大跨长联连续梁桥地震反应分析

为完善大跨长联连续梁桥的减震和隔震技术,提出将负刚度装置引入某带有摩擦摆支座隔震的大跨长联连续梁桥中组成新型减震和隔震系统.基于CSIBridge软件建立全桥有限元模型,负刚度装置采用弹性多段线模拟,摩擦摆支座采用双线性恢复力模型,输入7条地震波进行了非线性时程分析,考查了新型减震和隔震系统下桥梁结构的地震反应,探究了...     

Isolation parameters for improving the seismic performance of irregular bridges

Bridge structures are usually built on irregular topographical surfaces which create substructures with different pier heights and non uniform stiffness distribution. Three irregularity types of typical reinforced concrete (RC) medium length bridges located in a high seismicity zone of Mexico, were analyzed aimed at determining the best strength and stiffness parameters of an isolation system. The isolation system is composed by lead rubber bearings (LRB) located on each pile and abutment. The variation of the bridge characteristics and the isolation parameters produced 169 models that were subjected to ten seismic records representative of the subduction zone in the Pacific Coast of Mexico. A total of 1690 nonlinear time history analyses (NLTHA) were carried out in longitudinal and transverse directions of the structures. The maximum pier drifts, bending moments and shear forces demands were analyzed to identify the best isolation properties for reducing the concentration of damage in one or two elements and for improving the structural behavior of irregular bridges. Additionally, the analysis of the seismic response of the bridges supported on traditional neoprene bearings was carried out.     

考虑温度影响的LRB隔震建筑地震响应分析

为研究温度对铅芯橡胶支座(LRB)性能的影响,进行支座拟静力试验。试验表明,在不同温度环境中试件的滞回曲线明显不同,支座的刚度和屈服剪力均随温度的升高而降低;低温时,支座的力学特性变化较大,而当温度大于20℃时,支座的力学特性趋于稳定。以某五层基础隔震建筑为例,编写基础隔震结构非线性时程分析程序NBIS,计算该隔震建筑在考虑温度影响后的地震响应。结果表明,在多遇地震作用下支座恢复力随温度的升高而降低,与罕遇地震下的变化趋势相反;考虑LRB温度影响后,该基础隔震结构的减震系数随环境温度的降低而增大,支座的最大位移随温度升高而增大。     

脉冲型地震动作用下隔震结构动力响应的影响参数研究

通过对隔震结构进行非线性动力响应分析,分别研究地震动参数和支座参数对结构地震响应的影响。首先,建立铅芯橡胶支座基础隔震结构的非线性运动方程;然后,以人工合成脉冲型地震动作为输入,运用MATLAB进行编程并求解结构在脉冲型地震动作用下的地震响应;最后,分别研究速度脉冲周期、支座屈服力、屈服后与屈服前的刚度比对隔震支座最大位移和上部结构层间位移的影响。研究结果表明,脉冲周期对结构地震响应影响很大,在进行隔震设计时应使结构自振周期远离脉冲周期;支座刚度比对结构地震响应影响较大,在进行支座选型时应重点关注;支座屈服力对支座位移的影响显著,屈服力越大,支座位移越小。     

Study on effects of damping in laminated rubber bearings on seismic responses for a ⅛ scale isolated test structure

The effects of damping in various laminated rubber bearings (LRB) on the seismic response of a ?‐scale isolated test structure are investigated by shaking table tests and seismic response analyses. A series of shaking table tests of the structure were performed for a fixed base design and for a base isolation design. Two different types of LRB were used: natural rubber bearings (NRB) and lead rubber bearings (LLRB). Three different designs for the LLRB were tested; each design had a different diameter of lead plug, and thus, different damping values. Artificial time histories of peak ground acceleration 0.4g were used in both the tests and the analyses. In both shaking table tests and analyses, as expected, the acceleration responses of the seismically isolated test structure were considerably reduced. However, the shear displacement at the isolators was increased. To reduce the shear displacement in the isolators, the diameter of the lead plug in the LLRB had to be enlarged to increase isolator damping by more than 24%. This caused the isolator stiffness to increase, and resulted in amplifying the floor acceleration response spectra of the isolated test structure in the higher frequency ranges with a monotonic reduction of isolator shear displacement. Copyright © 2002 John Wiley & Sons, Ltd.     

模块化外框内箱结构抗震性能分析

基于《集装箱模块化组合房屋技术规程》中的要求,为提高模块化集装箱建筑的抗震性能,增加房屋的使用高度,提出了一种外框内箱结构,其由外框柱、外框梁和模块化集装箱拼装组成。为验证外框内箱结构的抗震性能,对六层传统集装箱结构和外框内箱结构进行了数值仿真分析,对比分析两种结构的层间位移角和构件应力分布等。结果表明:外框内箱结构竖向刚度分布均匀,受力更加合理,传力更加明确,能有效地减小内部集装箱构件内力,其能更好的实现结构"强柱弱梁和强节点"需求,提高结构的安全性和可靠性。     

Seismic performance of cable-sliding friction bearing system for isolated bridges

During past strong earthquakes, highway bridges have sustained severe damage or even collapse due to excessive displacements and/or very large lateral forces. For commonly used isolation bearings with a pure friction sliding surface, seismic forces may be reduced but displacements are often unconstrained. In this paper, an alternative seismic bearing system, called the cable-sliding friction bearing system, is developed by integrating seismic isolation devices with displacement restrainers consisting of cables attached to the upper and lower plates of the bearing. Restoring forces are provided to limit the displacements of the sliding component. Design parameters including the length and stiffness of the cables, friction coefficient, strength of the shear bolt in a fixed-type bearing, and movements under earthquake excitations are discussed. Laboratory testing of a prototype bearing subjected to vertical loads and quasi-static cyclic lateral loads, and corresponding numerical finite element simulation analysis, were carried out. It is shown that the numerical simulation shows good agreement with the experimental force-displacement hysteretic response, indicating the viability of the new bearing system. In addition, practical application of this bearing system to a multi-span bridge in China and its design advantages are discussed.