Comparative study of microstructural characteristics and stored energy of mechanically activated hematite in different grinding environments

Hematite concentrate was mechanically treated using different milling machines and experimental conditions in air atmosphere. The changes in phase constitution, particles size, specific surface area, lattice parameters and X-ray amorphous phase fraction of activated hematite were determined. It was found that the agglomeration of the particles take place during extended milling with accessible pores for Nitrogen gas. The higher media surface brought about the largest specific surface area whatever milling devices used. After 9 h of grinding with higher media surface, the maximum and minimum specific surface area resulted from the grinding in the tumbling and vibratory mills, accounting for 6.83 m²/g and 18.42 m²/g, respectively. For the same grinding condition, tumbling mill produced the lowest X-ray amorphous phase. The maximum X-ray amorphous material estimated around 85% from the grinding in the planetary mill with higher media surface for 9 h of milling.     

Investigating dissolution of mechanically activated olivine for carbonation purposes

Mineral carbonation is one of several alternatives for CO₂ sequestration and storage. The reaction rates of appropriate minerals with CO₂, for instance olivine and serpentine with vast resources, are relatively slow in a CO₂ sequestration context and the rates have to be increased to make mineral carbonation a good storage alternative. Increasing the dissolution rate of olivine has been the focus of this paper. Olivine was milled with very high energy intensity using a laboratory planetary mill to investigate the effect of mechanical activation on the Mg extraction potential of olivine in 0.01 M HCl solution at room temperature and pressure. Approximately 30–40% of each sample was dissolved and water samples were taken at the end of each experiment. The pH change was used to calculate time series of the Mg concentrations, which also were compared to the final Mg concentrations in the water samples. Percentage dissolved and the specific reaction rates were estimated from the Mg concentration time series. The measured particle size distributions could not explain the rate constants found, but the specific surface area gave a good trend versus dissolution for samples milled wet and the samples milled with a small addition of water. The samples milled dry had the lowest measured specific surface areas (<4 m²/g), but had the highest rate constants. The crystallinity calculated from X-ray diffractograms, was the material parameter with the best fit for the observed differences in the rate constants. Geochemical modelling of mechanically activated materials indicated that factors describing the changes in the material properties related to the activation must be included. The mechanically activated samples in general reacted faster than predicted by the theoretical models. Mechanical activation as a pre-treatment method was found to enhance the initial specific reaction rates by approximately three orders of magnitude for a sample milled dry for 60 min in a planetary mono mill compared to an unactivated sample. Wet milling in the planetary mill did not produce samples with the same maximum reaction rate as dry milling, but wet milling in general might be easier to implement into a wet carbonation process. Mechanical activation in a planetary mill is likely to consume too much energy for CO₂ sequestration purposes, but the increase in obtained olivine rate constants illustrates a potential for using milling as a pre-treatment method.     

Insights for size-dependent reactivity of hematite nanomineral surfaces through Cu sorption

Macroscopic sorption edges for Cu²⁺ were measured on hematite nanoparticles with average diameters of 7 nm, 25 nm, and 88 nm in 0.1 M NaNO₃. The pH edges for the 7 nm hematite were shifted approximately 0.6 pH units lower than that for the 25 nm and 88 nm samples, demonstrating an affinity sequence of 7 nm > 25 nm = 88 nm. Although, zeta potential data suggest increased proton accumulation at the 7 nm hematite surfaces, changes in surface structure are most likely responsible for the preference of Cu²⁺ for the smallest particles. As Cu²⁺ preferentially binds to sites which accommodate the Jahn-Teller distortion of its coordination to oxygen, this indicates the relative importance of distorted binding environments on the 7 nm hematite relative to the 25 nm and 88 nm particles. This work highlights the uniqueness of surface reactivity for crystalline iron oxide particles with decreasing nanoparticle diameter.     

Selective leaching of antimony and arsenic from mechanically activated tetrahedrite,jamesonite and enargite

In this study, the changes in surface area, morphology and leachability of antimony and arsenic from tetrahedrite, jamesonite and enargite mechanically activated by a high-energy planetary mill were investigated. It appears that the leaching of antimony from tetrahedrite and jamesonite and arsenic from enargite in alkaline solution of sodium sulphide is temperature-sensitive reaction. The temperature dependencies of all reactions were investigated in the interval 313–363 K. Resulting experimental activation energies were E_a = 111–182 kJ mol^− 1 for mechanically activated minerals. The values of E_a are characteristic for processes controlled by surface chemical reactions.     

Geology,mineral chemistry and tourmaline B isotopes of the Córrego Bom Sucesso area,southern Serra do Espinhaço,Minas Gerais,Brazil: Implications for Au–Pd–Pt exploration in quartzitic terrain

The Palaeo-Mesoproterozoic metasiliciclastic rocks of the southern Serra do Espinhaço, Minas Gerais, Brazil, are host to historically important alluvial deposits of diamonds and gold. Detrital gold grains often comprise Au–Pd–Pt intermetallic compounds, with low Ag contents, which contain inclusions of tourmaline and titaniferous hematite (up to ~ 6 wt.% TiO₂). The latter minerals connect the alluvial mineralisation to the rutile–hematite–quartz veins and tourmalinisation observed in the quartzitic country rocks of the alluvial gravel. The quartzite (Sopa-Brumadinho Formation of lacustrine to fan-deltaic origin) is affected by pervasive B metasomatism with F-bearing tourmaline replacing the recrystallised quartz fabric. The tourmaline belongs to the alkali group, with Mg/(Mg + Fe) and X/(X + Na) ratios in the ranges from 0.5 to 0.7 and 0.18 to 0.29, respectively, where X represents vacancies in the X site. Boron-isotopic values of tourmaline vary from ~ 1 to − 10.4‰ δ¹¹B. The B-isotope range, in conjunction with the Na–Mg-rich tourmaline composition, and the widespread occurrence of tourmalinite in the Sopa-Brumadinho Formation suggest a derivation from non-marine evaporitic brines. Brines are capable of transporting otherwise immobile Ti and explain, under oxidising conditions, the fractionation of Ag from Pd to precipitate palladiferous gold with extremely high Pd/Ag ratios. Zirconium-in-rutile and Ti-in-quartz temperatures for a variety of hematite-rich veins suggest episodic vein emplacement over a temperature range from around 500 °C to ~ 350 °C. Cross-cutting relationships and episodic vein emplacement indicate a late-Brasiliano age.     

A first approach to study the mobility and behavior of lead in hypersaline salt marsh sediments: Diffusive and advective fluxes,geochemical partitioning and Pb isotopes

A geochemical study of interstitial water and solid phase sediment using bulk concentration and geochemical partitioning was undertaken in vertical sediment profiles to trace diagenetic processes of lead (Pb) in hypersaline salt marsh sediments. In addition, we measured the stable isotopic composition of Pb in order to distinguish its input sources. Concentrations of Pb increased from low or background values in the bottommost layer (< 60 cm depth), followed by fluctuations in the middle layer (20–60 cm) and peak values in the subsurface layer (3–5 cm). Pb associated to reactive fractions (e.g. OM, Fe–Mn oxyhydroxides and carbonates) accounted for 60% of that initially deposited. Stable Pb isotope data (²⁰⁶Pb/²⁰⁷Pb and ²⁰⁷Pb/²⁰⁸Pb) suggested that most of the Pb in the upper sediments (1.204 ± 0.002 and 2.469 ± 0.007) is still derived from the leaded gasoline combustion (1.201 ± 0.006 and 2.475 ± 0.005). Profile of dissolved Pb was related to those for ammonium, phosphates and dissolve Fe and Mn, which reveals the influence of the diagenetic reactions on the Pb behavior. OM, Fe–Mn oxyhydroxides and the sulfide minerals play a significant role for mobilizing and trapping the Pb. Metal mobilization was calculated considering an advective–diffusive system. The advective process constitutes the dominant mechanism of Pb mobilization. A low diffusive outflux with respect to the Pb mobilization rate suggested that most of the released Pb is retained in the sediments. Authigenic oxides precipitated at the oxic–suboxic layers (0–4 cm depth) and authigenic sulfide minerals formed Pb in the anoxic layers (7–20 cm depth) constituting the main scavengers for Pb that is diagenetically released. This retention has significant environmental implications because it reduces the availability and toxicity of Pb to biota, including humans.     

Surface simulation studies of the hydration of white rust Fe(OH)2, goethite α-FeO(OH) and hematite α-Fe2O3

Computer modelling techniques were used to elucidate the hydration behaviour of three iron (hydr)oxide minerals at the atomic level: white rust, goethite and hematite. A potential model was first adapted and tested against the bulk structures and properties of eight different iron oxides, oxyhydroxides and hydroxides, followed by surface simulations of Fe(OH)₂, α-FeO(OH) and α-Fe₂O₃. The major interaction between the adsorbing water molecules and the surface is through interaction of their oxygen ions with surface iron ions, followed by hydrogen-bonding to surface oxygen ions. The energies released upon the associative adsorption of water range from 1 to 17 kJ mol⁻¹ for Fe(OH)₂, 26 to 80 kJ mol⁻¹ for goethite and 40 to 85 kJ mol⁻¹ for hematite, reflecting the increasing oxidation of the iron mineral. Dissociative adsorption at goethite and hematite surfaces releases larger hydration energies, ranging from 120 to 208 kJ mol⁻¹ for goethite and 76 to 190 kJ mol⁻¹ for hematite.The thermodynamic morphologies of the minerals, based on the calculated surface energies, agree well with experimental morphologies, where these are available. When the partial pressures required for adsorption of water from the gas phase are plotted against temperature for the goethite and hematite surfaces, taking into account experimental entropies for water, it appears that these minerals may well be instrumental in the retention of water during the cyclic variations in the atmosphere of Mars.     

Temporal variations in the concentration and isotopic signature of ammonium- and nitrate–nitrogen in soils under a breeding colony of Black-tailed Gulls (Larus crassirostris) on Kabushima Island,northeastern Japan

Temporal variations in the concentration and N isotopic ratios of inorganic N (NH₄– and NO₃–N) as affected by the soil temperature regime together with the input of bird excreta were analyzed in a sedentary soil under a dense colony (1.6 nests/m²) of breeding Black-tailed Gulls (Laruscrassirostris: a ground-nesting seabird). Surface soil samples were taken monthly from mid-March to late July 2005 from Kabushima Island, Hachinohe, northeastern Japan. The spatial concentration of inorganic N in the soils varied considerably on all sampling dates. There may be a statistically significant trend, showing increased NH₄–N content from settlement up to early June when the input of fecal N attains its maximum, and then decreases towards the end of breeding activity (early August). Abundant NO₃–N was observed in all soils, particularly in the later stage of breeding (up to 3800 mg-N/kg dry soil), refuting earlier claims that nitrification is unimportant in the soils. δ¹⁵N values of NH₄ in the soils showed unusually high values up to +51‰, reflecting N isotope fractionation due to volatilization of NH₃ during the mineralization. Mean δ¹⁵N values of the monthly collected totals of NH₄ and NO₃ were not significantly different at the 5% level based on ANOVA and significant differences were observed only among the three means of NO₃–N collected in mid-March (settlement of colony: δ¹⁵N = −0.2 ± 3.5‰) and late July (later stages of breeding: δ¹⁵N = +22.1 ± 7.0‰, +23.3 ± 7.8‰) at the 1% and 5% levels by t-test, respectively. Such an observation of significantly increased δ¹⁵N values for NO₃–N in soils from the fledgling stage indicates the integration of denitrification coupled with nitrification under a limited supply of fecal N.     

Solubility of nanocrystalline scorodite and amorphous ferric arsenate: Implications for stabilization of arsenic in mine wastes

Solubility experiments were performed on nanocrystalline scorodite and amorphous ferric arsenate. Nanocrystalline scorodite occurs as stubby prismatic crystals measuring about 50 nm and having a specific surface area of 39.88 ± 0.07 m²/g whereas ferric arsenate is amorphous and occurs as aggregated clusters measuring about 50–100 nm with a specific surface area of 17.95 ± 0.19 m²/g. Similar to its crystalline counterpart, nanocrystalline scorodite has a solubility of about 0.25 mg/L at around pH 3–4 but has increased solubilities at low and high pH (i.e. <2 and >6). Nanocrystalline scorodite dissolves incongruently at about pH > 2.5 whereas ferric arsenate dissolution is incongruent at all the pH ranges tested (pH 2–5). It appears that the solubility of scorodite is not influenced by particle size. The dissolution rate of nanocrystalline scorodite is 2.64 × 10⁻¹⁰ mol m⁻² s⁻¹ at pH 1 and 3.25 × 10⁻¹¹ mol m⁻² s⁻¹ at pH 2. These rates are 3–4 orders of magnitude slower than the oxidative dissolution of pyrite and 5 orders of magnitude slower than that of arsenopyrite. Ferric arsenate dissolution rates range from 6.14 × 10⁻⁹ mol m⁻² s⁻¹ at pH 2 to 1.66 × 10⁻⁹ mol m⁻² s⁻¹ at pH 5. Among the common As minerals, scorodite has the lowest solubility and dissolution rate. Whereas ferric arsenate is not a suitable compound for As control in mine effluents, nanocrystalline scorodite that can be easily precipitated at ambient pressure and temperature conditions would be satisfactory in meeting the regulatory guidelines at pH 3–4.     

Some breakage characteristics of ultra-fine wet grinding with a centrifugal mill

A centrifugal mill is a high-power intensity media mill that can be used for ultra-fine grinding, employing centrifugal forces generated by gyration of the axis of the mill tube in a circle. The mill charge motion is quite different depending on the ratio of the gyration diameter to the mill diameter (G / D ratio), varying from a motion similar to that of a conventional tumbling media mill to that of a vibration mill. In this study, a centrifugal mill was constructed with an arrangement where the gyration diameter could be readily adjusted. The batch grinding characteristics of three different minerals (limestone, talc and illite) in water with dispersing agent were investigated at various G / D ratios. It was found that the optimum G / D ratio in terms of the specific energy consumption to give a desired fineness of product was different for the three minerals. This was due to their different reactions to the breakage mechanisms provided by the mill charge motion at varying G / D ratios. The size distributions became progressively narrower at increased grinding times, and particles finer than about 0.1 μm were not detected even for prolonged grinding times. Measurement of specific surface areas indicated that this was not due to an artifact of the size measurements by laser diffractometry. This implies that there is a limitation in which particles finer than 0.1 μm are not produced under the conditions tested in this type of mill, but further investigation is needed for experimental verification of this limit of comminution.     

Diagenetic processes on metals in hypersaline mudflat sediments from a subtropical saltmarsh (SE Gulf of California): Postdepositional mobility and geochemical fractions

To understand the biogeochemical cycles of trace metals (Cd, Cu, Fe, Mn, Ni and Zn) in a hypersaline subtropical marsh, geochemical studies of both interstitial and solid phases were conducted on sediment cores from Chiricahueto marsh, SE Gulf of California. The sequential extraction procedure proposed by Tessier was used to estimate the percentages of the metals present in each geochemical phase of the sediment. Metal concentrations in the solid phase were found to be enriched in the upper layers and mainly associated with reactive fractions such as organic matter, Fe–Mn oxyhydroxides and carbonates (46–74% of Ni, Mn and Cd, and 11–19% of Cu and Zn). Principal factor analysis (PFA) and Spearman correlation analysis revealed a strong positive association of metals and their reactive phases with OC (the diagenetic component), and a negative or non-association with the mud content, Al, Fe and Li (the lithogenic component). Diagenetically released metals are mainly mobilized within hypersaline sediments by buoyancy transport (>90% of total flux) in response to an extreme salinity gradient by input of fresh groundwater (3–6 psu cm⁻¹). The molecular diffusion due to the gradient of metals in porewater (maximum and higher levels at 5–7 and below 20 cm depth, respectively) is significantly less important to the advective transport. Most of the metals mobilized by diffusion–advection processes are re-precipitated in the sediments by authigenic minerals, only <10% of most metals are extruded out to the overlying water column. Authigenic accumulation rates were estimated as 1.42–7.09 mg m⁻² a⁻¹ for Cd; 58.8–378 for Cu; 6922–17,985 for Fe; 38.2–345 for Mn; 20.8–263 for Ni; and 282–2956 mg m⁻² a⁻¹ for Zn. The Mn–Fe oxyhydroxides (40–85% of reactive metals) in the upper oxic–suboxic layers (<5 cm below surface) and sulfide minerals (75–97%) in anoxic sediment layers (7–18 cm) constitute the main scavengers for metals.     

Stable isotope and Rare Earth Element evidence for recent ironstone pods within the Archean Barberton greenstone belt, South Africa

There is considerable debate about the mode and age of formation of large (up to ∼200 m long) hematite and goethite ironstone bodies within the 3.2 to 3.5 Ga Barberton greenstone belt. We examined oxygen and hydrogen isotopes and Rare Earth Element (REE) concentrations of goethite and hematite components of the ironstones to determine whether these deposits reflect formation from sea-floor vents in the Archean ocean or from recent surface and shallow subsurface spring systems. Goethite δ¹⁸O values range from −0.7 to +1.0‰ and δD from −125 to −146‰, which is consistent with formation from modern meteoric waters at 20 to 25 °C. Hematite δ¹⁸O values range from −0.7 to −2.0‰, which is consistent with formation at low to moderate temperatures (40-55 °C) from modern meteoric water. REE in the goethite and hematite are derived from the weathering of local sideritic ironstones, silicified ultramafic rocks, sideritic black cherts, and local felsic volcanic rocks, falling along a mixing line between the Eu/Eu* and shale-normalized HREE_Avg/LREE_Avg values for the associated silicified ultramafic rocks and felsic volcanic rocks. Contrasting positive Ce/Ce* of 1.3 to 3.5 in hematite and negative Ce/Ce* of 0.2 to 0.9 in goethite provides evidence of oxidative scavenging of Ce on hematite surfaces during mineral precipitation. These isotopic and REE data, taken together, suggest that hematite and goethite ironstone pods formed from relatively recent meteoric waters in shallow springs and/or subsurface warm springs.     

Estimating specific surface area of fine stream bed sediments from geochemistry

Specific surface area (SSA) of headwater stream bed sediments is a fundamental property which determines the nature of sediment surface reactions and influences ecosystem-level, biological processes. Measurements of SSA – commonly undertaken by BET nitrogen adsorption – are relatively costly in terms of instrumentation and operator time. A novel approach is presented for estimating fine (<150 μm) stream bed sediment SSA from their geochemistry – after removal of organic matter – for agricultural headwater catchments across 15,400 km² of central England, UK. From a regional set of 1972 stream bed sediment sites with common characteristics for which geochemical data were available, 60 samples were selected – based on maximising their variation in Al concentrations – and their BET SSA measured by N₂ adsorption. After careful selection of potential regression predictors following a principal component analysis and removal of a subset of samples with the largest Mo concentrations (>2.5 mg kg⁻¹), four elements were identified as significant predictors of SSA (ordered by decreasing predictive power): V > Ca > Al > Rb. The optimum model from these four elements accounted for 73% of the variation in bed sediment SSA (range 6–46 m² g⁻¹) with a root mean squared error of prediction – based on leave-one-out cross-validation – of 6.3 m² g⁻¹. It is believed that V is the most significant predictor because its concentration is strongly correlated both with the quantity of Fe-oxides and clay minerals in the stream bed sediments, which dominate sediment SSA. Sample heterogeneity in SSA – based on triplicate measurements of sub-samples – was a substantial source of variation (standard error = 2.2 m² g⁻¹) which cannot be accounted for in the regression model.     

Temporal and spatial variability of geochemical backgrounds in the Windmill Islands,East Antarctica: Implications for climatic changes and human impacts

To establish a natural background and its temporal and spatial variability for the area around Casey Station in the Windmill Islands, East Antarctica, the authors studied major and trace element concentrations and the distribution of organic matter in marine and lacustrine sediments. A wide range of natural variability in trace metal concentrations was identified between sites and within a time scale of 9 ka (e.g., Ni 5–37 mg kg⁻¹, Cu 20–190 mg kg⁻¹, Zn 50–300 mg kg⁻¹, Pb 4.5–34 mg kg⁻¹). TOC concentrations are as high as 3 wt.% at the marine sites and 20 wt.% at the lacustrine sites, and indicate highly productive ecosystems. These data provide a background upon which the extent of human impact can be established, and existing data indicate negligible levels of disturbance. Geochemical and lithological data for a lacustrine sediment core from Beall Lake confirm earlier interpretation of recent climatic changes based on diatom distribution, and the onset of deglaciation in the northern part of the Windmill Islands between 8.6 and 8.0 ka BP. The results demonstrate that geochemical and lithological data can not only be used to define natural background values, but also to assess long-term climatic changes of a specific environment. Other sites, however, preserve a completely different sedimentary record. Therefore, inferred climatic record, and differences between sites, can be ascribed to differences in elevation, distance from the shore, water depth, and local catchment features. The extreme level of spatial variability seems to be a feature of Antarctic coastal areas, and demonstrates that results obtained from a specific site cannot be easily generalized to a larger area.     

Permian volcanic rocks from the Apuseni Mountains (Romania): Geochemistry and tectonic constraints

An Early Permian volcanic assemblage is well exposed in the central-western part of the Apuseni Mountains (Romania). The rocks are represented by rhyolites, basalts and subordinate andesites suggesting a bimodal volcanic activity that is intimately associated with a post-orogenic (Variscan) syn-sedimentary intra-basinal continental molasse sequences. The mafic and mafic-intermediate rocks belong to sub-alkaline tholeiitic series were separated in three groups (I–III) showing a high Th and Pb abundances, depletion in Nb, Ta and Sr, and slightly enriched in LREE patterns (La_N/Yb_N = 1.4–4.4). Isotopically, the rocks of Group I have the initial ratios ⁸⁷Sr/⁸⁶Sr_(i) = 0.709351–0.707112, ¹⁴³Nd/¹⁴⁴Nd_(i) = 0.512490–0.512588 and high positive ?_Nd270 values from 3.9 to 5.80; the rocks of Group II present for the initial ratios values ⁸⁷Sr/⁸⁶Sr_(i) = 0.709434–0.710092, ¹⁴³Nd/¹⁴⁴Nd_(i) = 0.512231–0.512210 and for ?_Nd270 the negative values from −1.17 to −1.56; the rocks of Group III display for the initial ratios the values ⁸⁷Sr/⁸⁶Sr_(i) = 0.710751–0.709448, ¹⁴³Nd/¹⁴⁴Nd_(i) = 0.512347–0.512411 and for ?_Nd270 the positive values from 1.64 to 2.35. The rocks resembling continental tholeiites, suggest a mantle origin and were further affected by fractionation and crustal contamination. In addition, the REE geochemistry (1 > Sm_N/Yb_N < 2.5; 0.9 > La_N/Sm_N < 2.5) suggests that these rocks were generated by high percentage partial melting of a metasomatized mantle in the garnet peridotite facies. The felsic rocks are enriched in Cs, Rb Th and U and depleted in Nb, Ta, Sr, Eu, and Ti. The REE fractionation patterns show a strong negative Eu anomaly (Eu/Eu* = 0.23–0.40). The felsic rocks show the initial ratios the values: ⁸⁷Sr/⁸⁶Sr_(i) = 0.704096–0.707805, ¹⁴³Nd/¹⁴⁴Nd_(i) = 0.512012–0.512021 and for ?_Nd270 the negative values from −5.27 to −5.44. They suggest to be generated within the lower crust during the emplacement of mantle-derived magmas that provided necessary heat to crustal partial melting.     

Influence of waterfall aeration and seasonal temperature variation on the iron and arsenic attenuation rates in an acid mine drainage system

Dramatic seasonal changes in water chemistry and precipitate mineralogy associated with acid-mine drainage (AMD) in the waterfall and creek sections of the Chinkuashih area, northern Taiwan were investigated. Special attention has been paid to the kinetic effects of seasonal temperature variation and waterfall aeration. Precipitation of schwertmannite associated with removal of metals and As are indicated by delicate growth microstructures on precipitate surfaces, X-ray diffraction data, and downstream reductions of metal and As concentrations. Geochemical modeling suggested a downstream increase of the degree of saturation/supersaturation with respect to schwertmannite in the waterfall section, which can be attributed to high Fe²⁺ oxidation rates. The waterfall section was characterized by high rates and model rate constants of Fe²⁺ oxidation (6.1–6.7 × 10⁻⁶ mol L⁻¹ s⁻¹ and 2.7–2.9 × 10⁻² s⁻¹) and Fe (schwertmannite) precipitation (1.7–2.1 × 10⁻⁶ mol L⁻¹ s⁻¹ and 3.5–4.1 × 10⁻⁷ mol L⁻¹ s⁻¹). A high As sorption rate (4.7–6.3 × 10⁻⁹ mol L⁻¹ s⁻¹) and low As distribution coefficient (7.9–11.8 × 10⁻⁹ mol⁻¹ L) were observed. The creek section showed up to 1–2 orders of magnitude slower rates and lower rate constants than the waterfall section and had seasonal variations comparable to those in areas polluted by AMD elsewhere. The summer rates were 4–5 times higher than the winter rates in the creek section, and are largely attributed to a temperature effect. In contrast, the seasonal differences in rate and rate constant were small in the waterfall section. Several factors associated with the waterfall aeration in addition to elevated temperature and As concentration enhanced Fe and As attenuation in the waterfall section. The waterfall effects on Fe precipitation rate were enhanced when the flow rate was large in the winter. Despite the remarkable removal of metals and As by the rapid precipitation of As-bearing schwertmannite, large effluent loads of potentially hazardous contaminants including As, Cu and Zn discharged to the sea in the Chinkuashih area.     

Spatial distribution and source diagnosis of polycyclic aromatic hydrocarbons in soils from Chengdu Economic Region,Sichuan Province,western China

Surface soils from the Chengdu Economic Region (CER) were analyzed for sixteen United States Environment Protection Agency priority polycyclic aromatic hydrocarbons (PAHs) to study the spatial distribution and to identify the sources of PAHs. Relatively high concentrations (more than 1500 ngg^− 1) of high molecular weight PAHs were found in Chengdu Plain, in the middle of CER, while high concentrations (more than 500 ng g^− 1) of low molecular weight PAHs were detected in the surrounding mountains. The concentrations of ∑₁₆-PAHs in topsoil samples from CER (12.52–75,431.47 ngg^− 1, average value was 3233.92 ngg^− 1) were higher than that from the southern China (21.91–3077 ngg^− 1, average value was less than 500 ngg^− 1), and they were comparable to concentrations in soils from the northern China (366–254,080 ngg^− 1, mean value was more than 3000 ngg^− 1). The concentrations from CER were also much higher than the concentrations of some world clean regions such as Antarctic (34.9–171 ngg^− 1), European high mountains (9–11,000 ngg^− 1, mean value was 158 ngg^− 1) and some Europe residential (736 ngg^− 1) and arable soils (60–145 ngg^− 1, mean value was 66 ngg^− 1). The ratio of tracer compounds (BaA/(BaA + Chr), Flo/(Flo + Pyr), and IcdP/(IcdP + BghiP)) indicated that the high concentrations of PAHs in soils were mainly derived from fossil fuels combustion in mountain region and from the incomplete combustion of petroleum in developed plain area (such as Chengdu and Deyang). From the above distribution characteristics and ratios of tracer compounds, we inferred the reasons for the distribution pattern of PAHs in CER were the domestic heating, emissions, and the physicochemical properties of PAHs.     

Bridging arsenate surface complexes on the hematite (0 1 2) surface

The fate of the oxoanion arsenate in diverse systems is strongly affected by its adsorption on the surfaces of iron (oxyhydr)oxide minerals. Predicting this behavior in the environment requires an understanding of the mechanisms of arsenate adsorption. In this study, the binding site and adsorption geometry of arsenate on the hematite (0 1 2) surface is investigated. The structure and termination of the hematite (0 1 2)-water interface were determined by high resolution X-ray reflectivity, revealing that two distinct terminations exist in a roughly 3:1 proportion. The occurrence of multiple terminations appears to be a result of sample preparation, and is not intrinsic to the hematite (0 1 2) surface. X-ray standing wave (XSW) measurements were used to determine the registry of adsorbed arsenate to the hematite structure, and thus the binding site and geometry of the resulting surface complex. Arsenate forms a bridging bidentate complex on two adjacent singly coordinated oxygen groups on each of the two distinct terminations present at the hematite surface. Although this geometry is consistent with that seen in past studies, the derived As-Fe distances are longer, the result of the topology of the FeO₆ octahedra on the (0 1 2) surface. As EXAFS-derived As-Fe distances are often used to determine the adsorption mechanism in environmental samples (e.g., mine tailings, contaminated sediments), this demonstrates the importance of considering the possible sorbent surface structures and arrangements of adsorbates when interpreting such data.As multiple functional groups are present and multiple binding geometries are possible on the hematite (0 1 2) surface, the XSW data suggest that formation of bridging bidentate surface complexes on singly coordinated oxygen sites is the preferred adsorption mechanism on this and most other hematite surfaces (provided those surfaces contain adjacent singly coordinated oxygen groups). These measurements also constrain the likely reaction stoichiometry, with only the protonation state of the surface complex undetermined. Although bridging bidentate inner-sphere surface complexes comprised the majority of the adsorbed arsenate present on the hematite (0 1 2) surface, there is an additional population of sorbed arsenate species that could not be characterized by the XSW measurements. These species are likely more disordered, and thus more weakly bound, than the bridging bidentate complexes, and may play a role in determining the fate, transport, and bioavailability of arsenate in the environment. Finally, the possibility of obtaining species-specific XSW measurements by tuning the incident beam energy to specific features in a XANES spectrum is described.     

Dissolved metals and associated constituents in abandoned coal-mine discharges,Pennsylvania, USA. Part 1: Constituent quantities and correlations

Complete hydrochemical data are rarely reported for coal-mine discharges (CMD). This report summarizes major and trace-element concentrations and loadings for CMD at 140 abandoned mines in the Anthracite and Bituminous Coalfields of Pennsylvania. Clean-sampling and low-level analytical methods were used in 1999 to collect data that could be useful to determine potential environmental effects, remediation strategies, and quantities of valuable constituents. A subset of 10 sites was resampled in 2003 to analyze both the CMD and associated ochreous precipitates; the hydrochemical data were similar in 2003 and 1999. In 1999, the flow at the 140 CMD sites ranged from 0.028 to 2210 L s⁻¹, with a median of 18.4 L s⁻¹. The pH ranged from 2.7 to 7.3; concentrations (range in mg/L) of dissolved (0.45-μm pore-size filter) SO₄ (34–2000), Fe (0.046–512), Mn (0.019–74), and Al (0.007–108) varied widely. Predominant metalloid elements were Si (2.7–31.3 mg L⁻¹), B (<1–260 μg L⁻¹), Ge (<0.01–0.57 μg L⁻¹), and As (<0.03–64 μg L⁻¹). The most abundant trace metals, in order of median concentrations (range in μg/L), were Zn (0.6–10,000), Ni (2.6–3200), Co (0.27–3100), Ti (0.65–28), Cu (0.4–190), Cr (<0.5–72), Pb (<0.05–11) and Cd (<0.01–16). Gold was detected at concentrations greater than 0.0005 μg L⁻¹ in 97% of the samples, with a maximum of 0.0175 μg L⁻¹. No samples had detectable concentrations of Hg, Os or Pt, and less than half of the samples had detectable Pd, Ag, Ru, Ta, Nb, Re or Sn. Predominant rare-earth elements, in order of median concentrations (range in μg/L), were Y (0.11–530), Ce (0.01–370), Sc (1.0–36), Nd (0.006–260), La (0.005–140), Gd (0.005–110), Dy (0.002–99) and Sm (<0.005–79). Although dissolved Fe was not correlated with pH, concentrations of Al, Mn, most trace metals, and rare earths were negatively correlated with pH, consistent with solubility or sorption controls. In contrast, As was positively correlated with pH.