Arsenic distribution in the dissolved, colloidal and particulate size fraction of experimental solutions rich in dissolved organic matter and ferric iron

Due to the widespread contamination of groundwater resources with arsenic (As), controls on As mobility have to be identified. In this study we focused on the distribution of As in the dissolved, colloidal and particulate size fraction of experimental solutions rich in ferric iron, dissolved organic matter (DOM) and As(V). Size fractions between <5 kDa and >0.2 μm were separated by filtration and their elemental composition was analyzed. A steady-state particle size distribution with stable element concentration in the different size classes was attained within 24 h. The presence of DOM partly inhibited the formation of large Fe-(oxy)hydroxide aggregates, thus stabilized Fe in complexed and colloidal form, when initially adjusted molar Fe/C ratios in solution were <0.1. Dissolved As concentrations and the quantity of As bound to colloids (<0.2 μm) increased in the presence of DOM as well. At intermediate Fe/C ratios of 0.02-0.1, a strong correlation between As and Fe concentration occurred in all size fractions (R² = 0.989). At Fe/C ratios <0.02, As was mainly present in the dissolved size fraction. These observations indicate that As mobility increased in the presence of DOM due to (I) competition between As and organic molecules for sorption sites on Fe particles; and (II) due to a higher amount of As bound to more abundant Fe colloids or complexes <0.2 μm in size. The amount of As contained in the colloidal size fractions also depended strongly on the initial size of the humic substance, which was larger for purified humic acids than for natural river or soil porewater samples. Arsenic in the particle size fraction >0.2 μm additionally decreased in the order of pH 4 ? 6 > 8. The presence of DOM likely increases the mobility of As in iron rich waters undergoing oxidation, a finding that has to be considered in the investigation of organic-rich terrestrial and aquatic environments.     

Local-scale spatial variability of soil organic carbon and its stock in the hilly area of the Loess Plateau, China

Soil organic carbon (SOC) is one of the key components for assessing soil quality. Meanwhile, the changes in the stocks SOC may have large potential impact on global climate. It is increasingly important to estimate the SOC stock precisely and to investigate its variability. In this study, Yangjuangou watershed was selected to investigate the SOC distribution under different land uses. We found that SOC concentration decreased with increasing soil depth under all land uses and was significantly different across the vertical soil profile (P < 0.01). However, considering effect of land use on SOC, it is only significant (P < 0.01) in the topsoil (0-5 cm) layer. This indicated that land use has a large effect on the stocks of SOC in the surface soil. The stratification ratio of SOC > 1.2 may mean that soil quality is improving. The order of the SOC density (0-30 cm) under different land uses is forestland > orchard land > grassland > immature forestland > terraced cropland. The SOC stock is found to be as large as 2.67 × 10³ t (0-30 cm) in this watershed. Considering time effect of restoration, the slope cropland just abandoned is more efficient for SOC accumulation than trees planted in the semi-arid hilly loess area.     

Behavior of metals (Cu,Zn and Cd) in the initial stage of water system contamination: Effect of pH and suspended particles

The fate of potentially harmful metals (PHM) after their entry into an unpolluted fresh water body depends on the physicochemical and biological parameters of the aquatic ecosystem. This paper considers the effect of pH and suspended particles (SP) on the behavior of Cu, Zn and Cd when they enter a fresh water reservoir. In a field experiment, four mesocosms were constructed in the Novosibirskoye Reservoir to allow systematic variation of SP concentration (15 or 250 mg/L) and pH (8.5 or 6.5). The initial concentrations of Cu, Zn and Cd in the mesocosms were 1000, 1000 and 200 μg/L, respectively. Natural bottom sediments were used to provide additional mineral SP, and water hyacinth was used as a floating plant species. Over 11 days, measurements were made of several indicators: residual metal concentration in solution ([PHM]_w); metal concentration in SP ([PHM]_s); primary productivity of the phytoplankton community; mass of settled SP; PHM concentration in settled SP; and PHM bioaccumulation by water hyacinth. The ratio [PHM]_w/[PHM]_s in the water varied in the order Cu < Zn < Cd and was higher at pH 6.5 than at pH 8.5. This observation reflects different PHM sorption (Cu > Zn > Cd) onto mineral SP and PHM biosorption by planktonic organisms. Phytoplankton acts as a renewable source of organic SP and plays an important role in metal removal from the water in the mesocosms. After 11 days the residual concentrations of Cu, Zn and Cd in the mesocosm without SP addition (initial SP concentration was 15 mg/L) were 272, 355 and 84 μg/L, respectively. The residual concentrations of Cu, Zn and Cd in mesocosms with SP addition were 57, 100 and 14 μg/L at pH 8.5 and 80, 172 and 20 μg/L at pH 6.5, respectively. Therefore, addition of SP resulted in faster and more complete removal of metals into the bottom sediments. Floating plants (water hyacinth) accumulated PHM (Cu > Zn > Cd) more effectively at pH 8.5 than at pH 6.5, and PHM concentrations in the roots were higher than in settling SP. The general trends of PHM removal from contaminated water via sedimentation and bioaccumulation are compared with changes of metal speciation in solution.     

Stable isotope fractionation during bacterial sulfate reduction is controlled by reoxidation of intermediates

Bacterial sulfate reduction is one of the most important respiration processes in anoxic habitats and is often assessed by analyzing the results of stable isotope fractionation. However, stable isotope fractionation is supposed to be influenced by the reduction rate and other parameters, such as temperature. We studied here the mechanistic basics of observed differences in stable isotope fractionation during bacterial sulfate reduction. Batch experiments with four sulfate-reducing strains (Desulfovibrio desulfuricans, Desulfobacca acetoxidans, Desulfonatronovibrio hydrogenovorans, and strain TRM1) were performed. These microorganisms metabolize different carbon sources (lactate, acetate, formate, and toluene) and showed broad variations in their sulfur isotope enrichment factors. We performed a series of experiments on isotope exchange of ¹⁸O between residual sulfate and ambient water. Batch experiments were conducted with ¹⁸O-enriched (δ¹⁸O_water = +700‰) and depleted water (δ¹⁸O_water = −40‰), respectively, and the stable ¹⁸O isotope shift in the residual sulfate was followed. For Desulfovibrio desulfuricans and Desulfonatronovibrio hydrogenovorans, which are both characterized by low sulfur isotope fractionation (ε_S > −13.2‰), δ¹⁸O values in the remaining sulfate increased by only 50‰ during growth when ¹⁸O-enriched water was used for the growth medium. In contrast, with Desulfobacca acetoxidans and strain TRM1 (ε_S < −22.7‰) the residual sulfate showed an increase of the sulfate δ¹⁸O close to the values of the enriched water of +700‰. In the experiments with δ¹⁸O-depleted water, the oxygen isotope values in the residual sulfate stayed fairly constant for strains Desulfovibrio desulfuricans, Desulfobacca acetoxidans and Desulfonatronovibrio hydrogenovorans. However, strain TRM1, which exhibits the lowest sulfur isotope fractionation factor (ε_S < −38.7‰) showed slightly decreasing δ¹⁸O values.Our results give strong evidence that the oxygen atoms of sulfate exchange with water during sulfate reduction. However, this neither takes place in the sulfate itself nor during formation of APS (adenosine-5′-phosphosulfate), but rather in intermediates of the sulfate reduction pathway. These may in turn be partially reoxidized to form sulfate. This reoxidation leads to an incorporation of oxygen from water into the “recycled” sulfate changing the overall ¹⁸O isotopic composition of the remaining sulfate fraction. Our study shows that such incorporation of ¹⁸O is correlated with the stable isotope enrichment factor for sulfur measured during sulfate reduction. The reoxidation of intermediates of the sulfate reduction pathway does also strongly influence the sulfur stable isotope enrichment factor. This aforesaid reoxidation is probably dependent on the metabolic conversion of the substrate and therefore also influences the stable isotope fractionation factor indirectly in a rate dependent manner. However, this effect is only indirect. The sulfur isotope enrichment factors for the kinetic reactions themselves are probably not rate dependent.     

Kinetics of crystal nucleation in ionic solutions: Electrostatics and hydration forces

The heat of precipitation, the mean crystal size and the broadness of crystal size distribution of barium sulfate precipitating in aqueous solutions of different background electrolytes (KCl, NaCl, LiCl, NaBr or NaF), was shown to vary at constant thermodynamic driving force (supersaturation) and constant ionic strength depending on the salt present in solution. The relative inversion in the effect of respective background ions on the characteristics of barite precipitate was observed between two studied supersaturation (Ω) and ionic strength (IS) conditions. The crystal size variance (β²) increased in the presence of background electrolytes in the order LiCl < NaCl < KCl at Ω = 10^3.33 and IS = 0.03 M and KCl < NaCl < LiCl at Ω = 10^3.77 and IS = 0.09 M. At a given Ω and IS the respective size of barite crystals decreased with increasing β² in chloride salts of different cations and remained constant in sodium salts of different anions.We suggest that ionic salts affect the kinetics of barite nucleation and growth due to their influence on water of solvation and bulk solvent structure. This idea is consistent with the hypothesis that the kinetic barrier for barium sulfate nucleation depends on the frequency of water exchange around respective building units that can be modified by additives present in solution. In electrolyte solution the relative switchover between long range electrostatic interactions and short range hydration forces, which influence the dynamics of solvent exchange between an ion solvation shell and bulk fluid, results in the observed inversion in the effect of differently hydrated salts on nucleation rates and the resulting precipitate characteristics.     

Gold deposition on pyrite and the common sulfide minerals: An STM/STS and SR-XPS study of surface reactions and Au nanoparticles

Gold species spontaneously deposited on pyrite and chalcopyrite, pyrrhotite, galena, sphalerite from HAuCl₄ solutions at room temperature, as well as the state of the reacted mineral surfaces have been characterized using synchrotron radiation X-ray photoelectron spectroscopy (SR-XPS), scanning tunneling microscopy and tunneling spectroscopy (STM/STS). The deposition of silver from 10⁻⁴ M AgNO₃ has been examined for comparison. Gold precipitates as metallic nanoparticles (NPs) from about 3 nm to 30 nm in diameter, which tends to aggregate forming larger particles, especially on pyrite. The Au 4f binding energies increase up to 1 eV with decreasing size of individual Au⁰ NPs, probably due to the temporal charging in the final state. Concurrently, a positive correlation between the tunneling current and the particle size was found in STS. Both these size effects were observed for unusually large, up to 20 nm Au particles. In contrast, silver deposited on the minerals as nanoparticles of semiconducting sulfide showed no shifts of photoelectron lines and different tunneling spectra.The quantity of gold deposited on pyrite and other minerals increased with time; it was lower for fracture surfaces and it grew if minerals were moderately pre-oxidized, while the preliminary leaching in Fe(III)-bearing media inhibited the following Au deposition. After the contact of polished minerals with 10⁻⁴ M solution (pH 1.5) for 10 min, the gold uptake changed in the order CuFeS₂ > ZnS > PbS > FeAsS > FeS₂ > Fe₇S₈. It was noticed that the open circuit (mixed) potentials of the minerals varied in approximately the same order, excepting chalcopyrite. We concluded that the potentials of minerals were largely determined by Fe(II)/Fe(III) couple, whereas the reduction of gold complexes had a minor effect. As a result, the deposition of gold, although it proceeded via the electrochemical mechanism, increased with decreasing potential. This suggests, in particular, that the accumulation of “invisible” gold in arsenian pyrites and arsenopyrite under hydrothermal conditions may be explained by the low electrochemical potentials but not structural relationships between As and Au in solids.     

Long-term river discharge and multidecadal climate variability inferred from varved sediments, southwest Alaska

Sedimentological analyses of 289 years (AD 1718-2006) of varved sediment from Shadow Bay, southwest Alaska, were used to investigate hydroclimate variability during and prior to the instrumental period. Varve thicknesses relate most strongly to total annual discharge (r² = 0.75, n = 43, p < 0.0001). Maximum annual grain size depends most strongly on maximum spring daily discharge (r² = 0.63, n = 43, p < 0.0001) and maximum annual daily discharge (r² = 0.61, n = 43, p < 0.0001), while varve thickness is poorly correlated with maximum annual grain size (r² = 0.004, n = 287, p = 0.33). Relations between varve thickness and annual climate variables (temperature, precipitation, North Pacific (NP) and Pacific Decadal Oscillation (PDO) indices) are insignificant. On multidecadal timescales, however, regime shifts in varve thickness and total annual discharge coincide with shifts in NP and PDO indices. Periods with increased varve thickness and total annual discharge were associated with warm PDO phases and a strengthened Aleutian Low. The varve-inferred record of PDO suggests that any periodicity in the PDO varied over time, and that the early 19th century marked a transition to a more frequent or detectable shifts.     

Parameter studies on the rheology of limestone slurries

The influences of solids concentration, molecular weight of dispersant, particle size and distribution, and temperature on the rheological behaviour of limestone slurries have been investigated. The results reveal that when the solids concentration of a limestone slurry (< 100 μm) is increased from 60 wt.% (35.71 vol.%) to 78.5 wt.% (57.49 vol.%), the rheological behaviour of the slurry is transformed from a weakly dilatant characteristic to a pseudoplastic one with a yield stress, which is in combination with a thixotropic property at a higher solids concentration (i.e., ≥ 75 wt.% or 52.63 vol.%). At a certain shear rate, the apparent viscosity and the relative viscosity of the slurry increase exponentially with solids concentration. The extrapolated Bingham yield stress increases rather sharply in a power-law form with increasing solids concentration when the solids concentration of the slurry is larger than 70 wt.% (i.e., 46.36 vol.%). An attainable maximum packing solids fraction (?_m) is predicted as ?_m = 64.6 vol.% at the certain limestone–water suspension system. A polymeric dispersant named Dispersant S40 with a molecular weight of 5500 appears most effective for the reduction of the apparent viscosity of limestone slurry due to its good electrosteric stabilization and effective avoidance of depletion flocculation. The smaller the particle size and the narrower the size distribution, the more evident the pseudoplastic property of limestone slurry is with a larger yield stress and a larger apparent viscosity at a given shear rate in the range of 12 to 1200 s^− 1. Also, a statistic model describes a relationship between the particle size and distribution and the apparent viscosity of the slurries at a given solids concentration (i.e., 70 wt.% or 46.36 vol.%). However, a sufficient additive dosage of Dispersant S40 (i.e., ≥ 0.1 wt.%) significantly decreases or even eliminates the rheological differences of limestone slurries (apparent viscosities and extrapolated yield stresses) resulting from the difference in particle size and distribution. Besides, the apparent viscosity of limestone slurries decreases with increasing temperature in the range of 13 to 55 °C, regardless of the absence or the presence of Dispersant S40.     

The combined effects of chlorine and fluorine on the viscosity of aluminosilicate melts

The effect of fluorine and fluorine + chlorine on melt viscosities in the system Na₂O-Fe₂O₃-Al₂O₃-SiO₂ has been investigated. Shear viscosities of melts ranging in composition from peraluminous [(Na₂O + FeO) < (Al₂O₃ + Fe₂O₃)] to peralkaline [(Na₂O + FeO) > (Al₂O₃ + Fe₂O₃)] were determined over a temperature range 560-890 °C at room pressure in a nitrogen atmosphere. Viscosities were determined using the micropenetration technique in the range of 10^8.8 to 10^12.0 Pa s. The compositions are based on addition of FeF₃ and FeCl₃ to aluminosilicate melts with a fixed amount of SiO₂ (67 mol%). Although there was a significant loss of F and Cl during glass syntheses, none occurred during the viscometry experiments. The presence of fluorine causes a decrease in the viscosity of all melts investigated. This is in agreement with the structural model that two fluorines replace one oxygen; resulting in a depolymerisation of the melt and thus a decrease in viscosity. The presence of both chlorine and fluorine results in a slight increase in the viscosity of peraluminous melts and a decrease in viscosity of peralkaline melts. The variation in viscosity produced by the addition of both fluorine and chlorine is the opposite to that observed in the same composition melts, with the addition of chlorine alone (Zimova M. and Webb S.L. (2006) The effect of chlorine on the viscosity of Na₂O-Fe₂O₃-Al₂O₃-SiO₂ melts. Am. Mineral.91, 344-352). This suggests that the structural interaction of chlorine and fluorine is not linear and the rheology of magmas containing both volatiles is more complex than previously assumed.     

Selenium levels in Lebanese environment

Very limited research has been conducted on selenium (Se) in Lebanese soils and forage crops but no work has been done on Se in water and locally produced vegetables and grains. This research was conducted in order to quantify Se levels and its availability in agricultural soils, vegetables and grains in Lebanon. Sixty-six (66) soil samples were collected from 33 selected sites in Lebanon: the Bekaa Valley, coastal and mountainous regions. Thirteen (13) different plant types (86 samples) were sampled from the same locations. Also, 13 spring water and 10 bottled water samples were collected. Soil samples were analyzed for their physical and chemical properties. Selenium was extracted from soils with: deionized–distilled water (Soluble-Se), KH₂PO₄-0.1 M (MKP-Se) and concentrated (HNO₃ + HCl) mixture (acid-Se). Plant Se was extracted by acid digestion on a hotplate. Selenium concentrations were measured by the inductively coupled plasma-mass spectrophotometer (ICP-MS). The values of Soluble-Se, MKP-Se and acid-Se ranged between 47 and 142, 147 and 400, and 1749 and 4713 μg/kg, respectively, with average values of 95, 306, and 3118 μg/kg and at a ratio of 1:3:30. Thus, Se extracted with deionized–distilled water is a good indicator for Se availability in the studied soils. The average Se concentration in plants was in the following order: radish > lettuce > cucumber > cabbage > parsley > alfalfa > onion (leaves) > broccoli > tomato > mint > chickpeas > wheat > onion (bulbs). The Se levels in water samples were in the safe range (less than 50 μg/L) and ranged between 2.14 and 17.6 μg/L. The levels of Se in the three soil extractants were positively correlated with each other and with organic matter content, salinity and phosphorus (P). Selenium levels in plant samples were positively correlated at a 0.01 significance level with clay and P content.     

Sulfur biogeochemistry and isotopic fractionation in shallow groundwater and sediments of Owens Dry Lake, California

Groundwater and sediment samples (∼ 1 m depth) at sites representative of different groundwater pathways were collected to determine the aqueous speciation of sulfur and the fractionation of sulfur isotopes in aqueous and solid phases. In addition, selected sediment samples at 5 depths (from oxic to anoxic layers) were collected to investigate the processes controlling sulfur biogeochemistry in sedimentary layers. Pyrite was the dominant sulfur-bearing phase in the capillary fringe and groundwater zones where anoxic conditions are found. Low concentrations of pyrite (< 5.9 g kg^− 1) coupled with high concentrations of dissolved sulfide (4.81 to 134.7 mg L^− 1) and low concentrations of dissolved Fe (generally < 1 mg L^− 1) and reducible solid-phase Fe indicate that availability of reactive Fe limits pyrite formation. The relative uniformity of down-core isotopic trends for sulfur-bearing mineral phases in the sedimentary layers suggests that sulfate reduction does not result in significant sulfate depletion in the sediment. Sulfate availability in the deeper sediments may be enhanced by convective vertical mixing between upper and lower sedimentary layers due to evaporative concentration. The large isotope fractionation between dissolved sulfate and sedimentary sulfides at Owens Lake provides evidence for initial fractionation from bacterial sulfate reduction and additional fractionation generated by sulfide oxidation followed by disproportionation of intermediate oxidation state sulfur compounds. The high salinity in the Owens Lake brines may be a factor controlling sulfate reduction and disproportionation in hypersaline conditions and results in relatively constant values for isotope fractionation between dissolved sulfate and total reduced sulfur.     

The role of sulfate groups in controlling CaCO3 polymorphism

The nucleation and growth of CaCO₃ phases from aqueous solutions with SO₄²⁻:CO₃²⁻ ratios from 0 to 1.62 and a pH of ∼10.9 were studied experimentally in batch reactors at 25 °C. The mineralogy, morphology and composition of the precipitates were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy and microanalyses. The solids recovered after short reaction times (5 min to 1 h) consisted of a mixture of calcite and vaterite, with a S content that linearly correlates with the SO₄²⁻:CO₃²⁻ ratio in the aqueous solution. The solvent-mediated transformation of vaterite to calcite subsequently occurred. After 24 h of equilibration, calcite was the only phase present in the precipitate for aqueous solutions with SO₄²⁻:CO₃²⁻ ? 1. For SO₄²⁻:CO₃²⁻ > 1, vaterite persisted as a major phase for a longer time (>250 h for SO₄²⁻:CO₃²⁻ = 1.62). To study the role of sulfate in stabilizing vaterite, we performed a molecular simulation of the substitution of sulfate for carbonate groups into the crystal structure of vaterite, aragonite and calcite. The results obtained show that the incorporation of small amounts (<3 mole%) of sulfate is energetically favorable in the vaterite structure, unfavorable in calcite and very unfavorable in aragonite. The computer modeling provided thermodynamic information, which, combined with kinetic arguments, allowed us to put forward a plausible explanation for the observed crystallization behavior.     

Lead and its isotopes in the sediment of three sites on the Lebanese coast: Identification of contamination sources and mobility

Lead concentrations and isotopic composition of sediment samples collected from three sites within the Lebanese coastal zones were measured: at Akkar, Dora and Selaata. Akkar is located far from any direct source of contamination, while Dora and Selaata receive urban and industrial wastes, respectively. Low Pb concentrations (6–16 μg g⁻¹) were detected in the Akkar sediments, and high concentrations of Pb (70–101 μg g⁻¹) were detected in the Dora sediments. Measuring stable isotope ratios of Pb makes it possible to identify the principal sources of Pb in the Akkar sediments as Pb emitted from gasoline combustion and Pb originating from natural sources. On the other hand, Pb stable isotopic ratios in Dora sediments indicate that they are more highly influenced by anthropogenic sources. Isotopic Pb ratios in the Selaata deposits, where Pb concentrations range between 5 and 35 μg g⁻¹, have an exceptional radiogenic signature for marine sediments 1.25 < ²⁰⁶Pb/²⁰⁷Pb < 1.6 and 0.5 < ²⁰⁶Pb/²⁰⁸Pb < 0.67, which shows the impact of the phosphogypsum discharged by Selaata’s chemical plant. Isotopic Pb analysis applied to EDTA extracts, to test the mobility of Pb, shows that that this mobility is high (>60%) after 24 h of extraction, and that the extracted Pb is less radiogenic than the residual Pb.     

Recycled crust controls contrasting source compositions of Mesozoic and Cenozoic basalts in the North China Craton

We explore Fe/Mn and Nb/Ta ratios of basalts as potential tracers for differentiating melts of recycled mafic crustal lithologies from peridotitic melts. Trace elements and Fe/Mn ratios of the Mesozoic and Cenozoic basalts from East China were analyzed by ICP-MS. Low Nb/Ta ratios (15.4 ± 0.3 (2σ, n = 45)), high Nb and Ta contents (60.1 and 4.01 ppm) and high Fe/Mn ratios (64.7 ± 1.5 (2σ, n = 45)) characterize the <110 Ma basalts. Mesozoic basalts with ages >110 Ma are characterized by superchondritic Nb/Ta ratios (20.1 ± 0.3 (2σ, n = 25)), low Nb and Ta contents (10.8 and 0.54 ppm) and slightly lower Fe/Mn ratios (60.0 ± 1.1 (2σ, n = 25)). Both the Mesozoic and Cenozoic basalts have Fe/Mn ratios higher than basaltic melt formed by partial melting of peridotite at the same MgO and CaO levels. Although both the Mesozoic and Cenozoic basalts are characterized by highly fractionated REE patterns, the >110 Ma basalts have island arc-type trace element patterns (i.e., depletion in Nb and Ta), whereas OIB-type trace element patterns (e.g., no depletion in Nb and Ta) are characteristic of the <110 Ma basalts. Based on D_Fe/Mn values for olivine, clinopyroxene, orthopyroxene and garnet, high Fe/Mn ratios and negative correlations of Fe/Mn with Yb (Y) of the <110 Ma basalts suggest clinopyroxene/garnet-rich mantle sources. The lower Fe/Mn ratios and positive correlations of Fe/Mn with Y and Yb in the >110 Ma basalts suggest orthopyroxene/garnet-rich mantle sources. Combining these data with Sr-Nd isotopes, we present a conceptual model to explain the Nb/Ta ratios and PM-normalized trace element patterns of the >110 and <110 Ma basalts. Preferential melting of recycled ancient lower continental crust during Mesozoic lithospheric thinning resulted in (1) peridotite-melt/fluid reaction that formed the orthopyroxene/garnet-rich mantle sources for the >110 Ma basalts, and (2) peridotite + rutile-bearing eclogite mixing that formed the clinopyroxene/garnet-rich mantle sources for the <110 Ma basalts. The choice of models may indeed be arbitrary and non-unique, but the goal is to seek relatively simple forward models that explain the characteristics of the lavas, and the differences between the >110 and <110 Ma basalts, in a relatively consistent geodynamic framework.     

Modeling the adsorption of Cd (II), Cu (II), Ni (II), Pb (II) and Zn (II) onto montmorillonite

The adsorption of five toxic metallic cations, Cd(II), Cu(II), Ni(II), Pb(II) and Zn(II), onto montmorillonite was investigated as a function of pH and ionic strength and a two-site surface complexation model was used to predict the adsorption data. The results showed that in the lower pH range, 3∼6 for Cd, Cu, Ni and Zn, and 3∼4.5 for Pb, the adsorption was greatly affected by ionic strength, while in the higher pH range, the adsorption was not. In the lower pH range, the metallic cations were mainly bound through the formation of outer-sphere surface on the permanently charged basal surface sites (≡X⁻), while in the higher pH range the adsorption occurred mainly on the variably charged edge sites (≡SOH) through the formation of inner-sphere surface complexes. Acid-base surface constants and metal binding constants for the two sites were optimized using FITEQL. The adsorption affinity of the five metallic cations to the permanently charged sites of montmorillonite was Pb > Cu > Ni ≈ Zn ≈ Cd, while that to the variable charged sites was Pb ? Cu > Zn > Cd > Ni.     

Major and trace element geochemistry of Lake Bogoria and Lake Nakuru,Kenya, during extreme draught

The physico-chemical properties of water samples from the two athalassic endorheic lakes Bogoria and Nakuru in Kenya were analysed. Surface water samples were taken between July 2008 and October 2009 in weekly intervals from each lake. The following parameters were determined: pH, salinity, electric conductivity, dissolved organic carbon (DOC), the major cations (FAAS and ICP-OES) and the major anions (IC), as well as certain trace elements (ICP-OES). Samples of superficial sediments were taken in October 2009 and examined using Instrumental Neutron Activation Analysis (INAA) for their major and trace element content including rare earth elements (REE). Both lakes are highly alkaline with a dominance of Na > K > Si > Ca in cations and HCO₃ > CO₃ > Cl > F > SO₄ in anions. Both lakes also exhibited high concentrations of Mo, As and fluoride. Due to an extreme draught from March to October 2009, the water level of Lake Nakuru dropped significantly. This created drastic evapoconcentration, with the total salinity rising from about 20‰ up to 63‰. Most parameters (DOC, Na, K, Ca, F, Mo and As) increased with falling water levels. A clear change in the quality of DOC was observed, followed by an almost complete depletion of dissolved Fe from the water phase. In Lake Bogoria the evapoconcentration effects were less pronounced (total salinity changed from about 40‰ to 48‰). The distributions of REE in the superficial sediments of Lake Nakuru and Lake Bogoria are presented here for the first time. The results show a high abundance of the REE and a very distinct Eu depletion of Eu/Eu* = 0.33–0.45.     

Size, speciation and lability of NOM-metal complexes in hyperalkaline cave dripwater

Transport of trace metals by natural organic matter (NOM) is potentially an important vector for trace metal incorporation in secondary cave precipitates [speleothems], yet little is known about the size distribution, speciation and metal binding properties of NOM in cave dripwaters. A hyperalkaline cave environment (ca. pH 11) was selected to provide information on colloid-metal interactions in cave waters, and to address the lack of high-pH data in natural systems in general. Colloidal (1 nm-1 μm) NOM in hyperalkaline cave dripwater from Poole’s Cavern, UK, was characterised by flow field-flow fractionation (FlFFF) coupled to UV and fluorescence detectors and transmission electron microscopy (TEM) coupled to X-ray energy-dispersive spectroscopy (X-EDS); trace-metal lability was examined by diffusive gradients in thin films (DGT). Colloidal aggregates and small particulates (>1 μm) imaged by TEM were morphologically heterogeneous with qualitative elemental compositions (X-EDS spectra; n = 41) consistent with NOM aggregates containing aluminosilicates, and iron and titanium oxides. Globular organic colloids, with diameters between ca. 1 and 10 nm were the most numerous colloidal class and exhibited high UV-absorbance (254 nm) and fluorescence intensity (320:400 nm excitation: emission) in optical regions characteristic of humic-like compounds. Metal binding with humic substances was modelled using the WHAM 6.1 (model VI) and visual MINTEQ 3.0 (NICA-Donnan) speciation codes. At pH 11, both models predicted dominant humic binding of Cu (ca. 100%) and minimal binding of Ni and Co (ca. <1-7%). A DGT depletion experiment (7 days duration) with the hyperalkaline dripwater showed that the available proportion of each metal was much lower than its total concentration. Metal availability for DGT in the initial stages (24 h) was consistent with weaker binding of alkaline earth metals by humic substances (Ba > Sr > V > Cu > Ni > Co), compared to the transition metals. Integrated over the entire experiment, the DGT-available proportion of transition metals (Ni > Cu & V >> Co) differed greatly from the expected hierarchy from WHAM and MINTEQ, indicating unusually strong complexation of Co. Total metal concentrations of Cu, Ni, and Co in raw and filtered PE1 dripwater samples (n = 53) were well correlated (Cu vs. Ni, R² = 0.8; Cu vs. Co, R² = 0.5) and were strongly reduced (> ca. 50%) by filtration at ca. 100 and 1 nm, indicating a common colloidal association. Our results demonstrate that soil-derived colloids reach speleothems, despite transport through a karst zone with potential for adsorption, and that NOM is a dominant complexant of trace metals in high pH speleothem-forming groundwaters.     

Synthetic coprecipitates of exopolysaccharides and ferrihydrite. Part I: Characterization

Iron(III) (hydr)oxides formed at extracellular biosurfaces or in the presence of exopolymeric substances of microbes and plants may significantly differ in their structural and physical properties from their inorganic counterparts. We synthesized ferrihydrite (Fh) in solutions containing acid polysaccharides [polygalacturonic acid (PGA), alginate, xanthan] and compared its properties with that of an abiotic reference by means of X-ray diffraction, transmission electron microscopy, gas adsorption (N₂, CO₂), X-ray absorption spectroscopy, ⁵⁷Fe Mössbauer spectroscopy, and electrophoretic mobility measurements. The coprecipitates formed contained up to 37 wt% polymer. Two-line Fh was the dominant mineral phase in all precipitates. The efficacy of polymers to precipitate Fh at neutral pH was higher for polymers with more carboxyl C (PGA ∼ alginate > xanthan). Pure Fh had a specific surface area of 300 m²/g; coprecipitation of Fh with polymers reduced the detectable mineral surface area by up to 87%. Likewise, mineral micro- (<2 nm) and mesoporosity (2-10 nm) decreased by up to 85% with respect to pure Fh, indicative of a strong aggregation of Fh particles by polymers in freeze-dried state. C-1s STXM images showed the embedding of Fh particles in polymer matrices on the micrometer scale. Iron EXAFS spectroscopy revealed no significant changes in the local coordination of Fe(III) between pure Fh and Fh contained in PGA coprecipitates. ⁵⁷Fe Mössbauer spectra of coprecipitates confirmed Fh as dominant mineral phase with a slightly reduced particle size and crystallinity of coprecipitate-Fh compared to pure Fh and/or a limited magnetic super-exchange between Fh particles in the coprecipitates due to magnetic dilution by the polysaccharides. The pH_iep of pure Fh in 0.01 M NaClO₄ was 7.1. In contrast, coprecipitates of PGA and alginate had a pH_iep < 2. Considering the differences in specific surface area, porosity, and net charge between the coprecipitates and pure Fh, composites of exopolysaccharides and Fe(III) (hydr)oxides are expected to differ in their geochemical reactivity from pure Fe(III) (hydr)oxides, even if the minerals have a similar crystallinity.     

Quantifying inorganic sources of geochemical energy in hydrothermal ecosystems, Yellowstone National Park, USA

Combining analytical data from hot spring samples with thermodynamic calculations permits a quantitative assessment of the availability and ranking of various potential sources of inorganic chemical energy that may support microbial life in hydrothermal ecosystems. Yellowstone hot springs of diverse geochemical composition, ranging in pH from <2 to >9 were chosen for this study, and dozens of samples were collected during three field seasons. Field measurements of dissolved oxygen, nitrate, nitrite, total ammonia, total sulfide, alkalinity, and ferrous iron were combined with laboratory analyses of sulfate and other major ions from water samples, and carbon dioxide, hydrogen, methane, and carbon monoxide in gas samples to evaluate activity products for ∼300 coupled oxidation-reduction reactions. Comparison of activity products and independently calculated equilibrium constants leads to values of the chemical affinity for each of the reactions, which quantifies how far each reaction is from equilibrium. Affinities, in turn, show systematic behavior that is independent of temperature but can be correlated with pH of the hot springs as a proxy for the full spectrum of geochemical variability. Many affinities are slightly to somewhat dependent on pH, while others are dramatically influenced by changes in chemical composition. All reactions involving dissolved oxygen as the electron acceptor are potential energy sources in all hot spring samples collected, but the ranking of dominant electron donors changes from ferrous iron, and sulfur at high pH to carbon monoxide, hydrogen, and magnetite as pH decreases. There is a general trend of decreasing energy yields depending on electron acceptors that follows the sequence: O₂(aq) > NO₃⁻ ≈ NO₂⁻ ≈ S > pyrite ≈ SO₄⁻² ≈ CO(g) ≈ CO₂(g) at high pH, and O₂(aq) ≈ magnetite > hematite ≈ goethite > NO₃⁻ ≈ NO₂⁻ ≈ S ≈ pyrite ≈ SO₄⁻² at low pH. Many reactions that are favorable sources of chemical energy at one set of geochemical conditions fail to provide energy at other conditions, and vice versa. This results in energy profiles supplied by geochemical processes that provide fundamentally different foundations for chemotrophic microbial communities as composition changes.