Partitioned by process: Measuring post-fire debris-flow and rill erosion with Structure from Motion photogrammetry

After wildfire, hillslope and channel erosion produce large amounts of sediment and can contribute significantly to long-term erosion rates. However, pre-erosion high-resolution topographic data (e.g. lidar) is often not available and determining specific contributions from post-fire hillslope and channel erosion is challenging. The impact of post-fire erosion on landscape evolution is demonstrated with Structure from Motion (SfM) Multi-View Stereo (MVS) photogrammetry in a 1 km² Idaho Batholith catchment burned in the 2016 Pioneer Fire. We use SfM-MVS to quantify post-fire erosion without detailed pre-erosion topography and hillslope transects to improve estimates of rill erosion at adequate spatial scales. Widespread rilling and channel erosion produced a runoff-generated debris-flow following modest precipitation in October 2016. We implemented unmanned aerial vehicle (UAV)-based SfM-MVS to derive a 5 cm resolution digital elevation model (DEM) of the channel scoured by debris-flow. In the absence of cm-resolution pre-erosion topography, a synthetic surface was defined by the debris-flow scour's geomorphic signature and we used a DEM of Difference (DoD) to map and quantify channel erosion. We found 3467 ± 422 m³ was eroded by debris-flow scour. Rill dimensions along hillslope transects and Monte Carlo simulation show rilling eroded ~1100 m³ of sediment and define a volume uncertainty of 29%. The total eroded volume (4600 ± 740 m³) we measured in our study catchment is partitioned into 75% channel erosion and 25% rill erosion, reinforcing the importance of catchment size on erosion process-dominance. The deposit volume from the 2016 event was 5700 ± 1140 m³, indicating ~60% contribution from post-fire channel erosion. Dating of charcoal fragments preserved in stratigraphy at the catchment outlet, and reconstructions of prior deposit volumes provide a record of Holocene fire-related debris-flows at this site; results suggest that episodic wildfire-driven erosion (~6 mm/year) dominate millennial-scale erosion (~5 mm/Ka) at this site. © 2019 John Wiley & Sons, Ltd. © 2019 John Wiley & Sons, Ltd.     

Multitemporal ALSM change detection,sediment delivery,and process mapping at an active earthflow

Remote mapping and measurement of surface processes at high spatial resolution is among the frontiers in Earth surface process research. Remote measurements that allow meter‐scale mapping of landforms and quantification of landscape change can revolutionize the study of landscape evolution on human timescales. At Mill Gulch in northern California, USA, an active earthflow was surveyed in 2003 and 2007 by airborne laser swath mapping (ALSM), enabling meter‐scale quantification of landscape change. We calculate four‐year volumetric flux from the earthflow and compare it to long‐term catchment average erosion rates from cosmogenic radionuclide inventories from adjacent watersheds. We also present detailed maps of changing features on the earthflow, from which we can derive velocity estimates and infer dominant process. These measurements rely on proper digital elevation model (DEM) generation and a simple surface‐matching technique to align the multitemporal data in a manner that eliminates systematic error in either dataset. The mean surface elevation of the earthflow and an opposite slope that was directly influenced by the earthflow decreased 14 ± 1 mm/yr from 2003 to 2007. By making the conservative assumption that these features were the dominant contributor of sediment flux from the entire Mill Gulch drainage basin during this time interval, we calculate a minimum catchment‐averaged erosion rate of 0·30 ± 0·02 mm/yr. Analysis of beryllium‐10 (¹⁰Be) concentrations in fluvial sand from nearby Russian Gulch and the South Fork Gualala River provide catchment averaged erosion rates of 0·21 ± 0·04 and 0·23 ± 0·03 mm/yr respectively. From translated landscape features, we can infer surface velocities ranging from 0·5 m/yr in the wide upper ‘source’ portion of the flow to 5 m/yr in the narrow middle ‘transport’ portion of the flow. This study re‐affirms the importance of mass wasting processes in the sediment budgets of uplifting weak lithologies. Copyright © 2011 John Wiley & Sons, Ltd.     

10Be‐derived assessment of accelerated erosion in a glacially conditioned inner gorge,Entlebuch, Central Alps of Switzerland

Inner gorges often result from the propagation of erosional waves related to glacial/interglacial climate shifts. However, only few studies have quantified the modern erosional response to this glacial conditioning. Here, we report in situ ¹⁰Be data from the 64 km² Entlen catchment (Swiss Alps). This basin hosts a 7 km long central inner gorge with two tributaries that are >100 m‐deeply incised into thick glacial till and bedrock. The ¹⁰Be concentrations measured at the downstream end of the gorge yield a catchment‐wide erosion rate of 0.42 ± 0.04 mm yr^‐1, while erosion rates are consistently lower upstream of the inner gorge, ranging from 0.14 ± 0.01 mm yr^‐1 to 0.23 ± 0.02 mm yr^‐1. However, ¹⁰Be‐based sediment budget calculations yield rates of ~1.3 mm yr^‐1 for the inner gorge of the trunk stream. Likewise, in the two incised tributary reaches, erosion rates are ~2.0 mm yr^‐1 and ~1.9 mm yr^‐1. Moreover, at the erosional front of the gorge, we measured bedrock incision rates ranging from ~2.5 mm yr^‐1 to ~3.8 mm yr^‐1. These rates, however, are too low to infer a post‐glacial age (15–20 ka) for the gorge initiation. This would require erosion rates that are between 2 and 6 times higher than present‐day estimates. However, the downcutting into unconsolidated glacial till favored high erosion rates through knickzone propagation immediately after the retreat of the LGM glaciers, and subsequent hillslope relaxation led to a progressive decrease in erosion rates. This hypothesis of a two‐ to sixfold decrease in erosion rates does not conflict with the ¹⁰Be‐based erosion rate budgets, because the modern erosional time scale recorded by ¹⁰Be cover the past 2–3 ka only. These results point to the acceleration of Holocene erosion in response to the glacial overprint of the landscape. Copyright © 2012 John Wiley & Sons, Ltd.     

From mass‐wasting to slope stabilization – putting constrains on a tectonically induced transition in slope erosion mode: a case study in the Judea Hills,Israel

Calcrete‐coated remnants of landslide debris and alluvial deposits are exposed along the presently stable hillslopes of the Soreq drainage, Judea Hills, Israel. These remnants indicate that a transition from landslide‐dominated terrain to dissolution‐controlled hillslope erosion had occurred. This transition possibly occurred due to the significant decrease in tectonic uplift during the late Cenozoic. The study area is characterized by sub‐humid Mediterranean climate. The drainage hillslopes are typically mantled by thick calcrete crusts overlying Upper Cretaceous marine carbonate rocks. Using TT‐OSL dating of aeolian quartz grains incorporated in the calcrete which cements an ancient landslide deposit, we conclude that incision of ~100 m occurred from 1056 ± 262 to 688 ± 86 ka due to ~0·3° westward tilt of the region; such incision invoked high frequency of landslide activity in the drainage. The ages of a younger landslide remnant, alluvial terrace, and alluvial fan, all situated only a few meters above the present level of the active streambed, range between 688 ± 86 ka and 244 ± 25 ka and indicate that since 688 ± 86 the Soreq base level had stabilized and that landslide activity decreased significantly by the middle Pleistocene. Copyright © 2012 John Wiley & Sons, Ltd.     

Hillslope response to tectonic forcing in threshold landscapes

Hillslopes are thought to poorly record tectonic signals in threshold landscapes. Numerous previous studies of steep landscapes suggest that large changes in long‐term erosion rate lead to little change in mean hillslope angle, measured at coarse resolution. New LiDAR‐derived topography data enables a finer examination of threshold hillslopes. Here we quantify hillslope response to tectonic forcing in a threshold landscape. To do so, we use an extensive cosmogenic beryllium‐10 (¹⁰Be)‐based dataset of catchment‐averaged erosion rates combined with a 500 km² LiDAR‐derived 1 m digital elevation model to exploit a gradient of tectonic forcing and topographic relief in the San Gabriel Mountains, California. We also calibrate a new method of quantifying rock exposure from LiDAR‐derived slope measurements using high‐resolution panoramic photographs. Two distinct trends in hillslope behavior emerge: below catchment‐mean slopes of 30°, modal slopes increase with mean slopes, slope distribution skewness decreases with increasing mean slope, and bedrock exposure is limited; above mean slopes of 30°, our rock exposure index increases strongly with mean slope, and the prevalence of angle‐of‐repose debris wedges keeps modal slopes near 37°, resulting in a positive relationship between slope distribution skewness and mean slope. We find that both mean slopes and rock exposure increase with erosion rate up to 1 mm/a, in contrast to previous work based on coarser topographic data. We also find that as erosion rates increase, the extent of the fluvial network decreases, while colluvial channels extend downstream, keeping the total drainage density similar across the range. Our results reveal important textural details lost in 10 or 30 m resolution digital elevation models of steep landscapes, and highlight the need for process‐based studies of threshold hillslopes and colluvial channels. Copyright © 2012 John Wiley & Sons, Ltd.     

Changes to sediment sources following wildfire in a forested upland catchment,southeastern Australia

Few investigations link post‐fire changes to sediment sources and erosion processes with sediment yield response at the catchment scale. This linkage is essential if downstream impacts on sediment transport after fire are to be understood in the context of fire effects across different forest environments. In this study, we quantify changing source contributions to fine sediment (<63 µm) exported from a eucalypt forest catchment (136 ha) burnt by wildfire. The study catchment is one of a pair of research catchments located in the East Kiewa River valley in southeastern Australia that have been the subject of a research program investigating wildfire effects on runoff, erosion, and catchment sediment/nutrient exports. This previous research provided the opportunity to couple insights gained from a range of measurement techniques with the application of fallout radionuclides ¹³⁷Cs and ²¹⁰Pb_ex to trace sediment sources. It was found that hillslope surface erosion dominated exports throughout the 3·5‐year post‐fire measurement period. During this time there was a pronounced decline in the proportional surface contribution from close to 100% in the first six months to 58% in the fourth year after fire. Over the study period, hillslope surface sources accounted for 93% of the fine sediment yield from the burnt catchment. The largest decline in the hillslope contribution occurred between the first and second years after fire, which corresponded with the previously reported large decline in sediment yield, breakdown of water repellency in burnt soils, substantial reduction in hillslope erodibility, and rapid surface vegetation recovery. Coupling the information on sediment sources with hillslope process measurements indicated that only a small proportion of slopes contributed sediment to the catchment outlet, with material derived from near‐channel areas dominating the post‐fire catchment sediment yield response. Copyright © 2011 John Wiley & Sons, Ltd.     

Sub‐grid scale parameterization of hillslope runoff and erosion processes for catchment‐scale models of semi‐arid landscapes

The processes of hillslope runoff and erosion are typically represented at coarse spatial resolution in catchment‐scale models due to computational limitations. Such representation typically fails to incorporate the important effects of topographic heterogeneity on runoff generation, overland flow, and soil erosion. These limitations currently undermine the application of distributed catchment models to understand the importance of thresholds and connectivity on hillslope and catchment‐scale runoff and erosion, particularly in semi‐arid environments. This paper presents a method for incorporating high‐resolution topographic data to improve sub‐grid scale parameterization of hillslope overland flow and erosion models. Results derived from simulations conducted using a kinematic wave overland flow model at 0.5 m spatial resolution are used to parameterize the depth–discharge relationship in the overland flow model when applied at 16 m resolution. The high‐resolution simulations are also used to derive a more realistic parameterization of excess flow shear stress for use in the 16 m resolution erosion model. Incorporating the sub‐grid scale parameterization in the coarse‐resolution model (16 m) leads to improved predictions of overland flow and erosion when evaluated using results derived from high‐resolution (0.5 m) model simulations. The improvement in performance is observed for a range of event magnitudes and is most notable for erosion estimates due to the non‐linear dependency between the rates of erosion and overland flow. Copyright © 2013 John Wiley & Sons, Ltd.     

Quantifying rainfall controls on catchment‐scale landslide erosion in Taiwan

Landslide erosion is a dominant hillslope process and the main source of stream sediment in tropical, tectonically active mountain belts. In this study, we quantified landslide erosion triggered by 24 rainfall events from 2001 to 2009 in three mountainous watersheds in Taiwan and investigated relationships between landslide erosion and rainfall variables. The results show positive power‐law relations between landslide erosion and rainfall intensity and cumulative rainfall, with scaling exponents ranging from 2·94 to 5·03. Additionally, landslide erosion caused by Typhoon Morakot is of comparable magnitude to landslide erosion caused by the Chi‐Chi Earthquake (M_W = 7·6) or 22–24 years of basin‐averaged erosion. Comparison of the three watersheds indicates that deeper landslides that mobilize soil and bedrock are triggered by long‐duration rainfall, whereas shallow landslides are triggered by short‐duration rainfall. These results suggest that rainfall intensity and watershed characteristics are important controls on rainfall‐triggered landslide erosion and that severe typhoons, like high‐magnitude earthquakes, can generate high rates of landslide erosion in Taiwan. Copyright © 2012 John Wiley & Sons, Ltd.     

Gully,channel and hillslope erosion – an assessment for a traditionally managed catchment

Understanding landscape features such as gullying and soil erosion is an important issue in the long‐term dynamics and evolution of both natural, agricultural and rehabilitated (i.e. post‐mining) landscapes. Considerable research has been undertaken examining the initiation, movement and overall dynamics of such features. This study reports on a series of 34 gully heads and other erosion features, such as scour holes (five in total), located in channels in a catchment largely undisturbed by European activity in the Northern Territory, Australia over a 5 year period (2002–2007). During this period the erosion features were monitored for their headward advance/retreat, enlargement or in‐filling. The erosion features ranged in depth from 0.2 m to 1.5 m and widths of 0.3 m to 8 m. Hillslope erosion was also monitored using erosion pins. The catchment was subject to a range of rainfall regimes including extreme rainfall and a Category 5 cyclone and also was burnt every second year so that all grass cover was removed according to traditional management practice. The results of this monitoring show that the erosion features have changed little during this 5 year period. A remote sensing assessment found no relationship between erosion feature morphology and hillslope erosion. The monitored gullies heads and scour holes appear to be resilient landscape features, yet have a morphology that suggests they are ready for rapid headward movement and expansion, leading to a destabilisation of the catchment. Hillslope erosion was found to be related to wetness indices derived from a digital elevation model. Significant linkages were found between hillslope erosion and change in erosion feature depth, indicative of a strong hillslope–channel coupling. Copyright © 2010 Commonwealth of Australia     

Effects of hillslope topography on runoff response in a small catchment in the Fudoji Experimental Watershed,central Japan

We investigated the role of different hillslope units with different topographic characteristics on runoff generation processes based on field observations at two types of hillslopes (0·1 ha): a valley‐head (a convergent hillslope) and a side slope (a planar hillslope), as well as at three small catchments having two types of slopes with different drainage areas ranging from 1·9 to 49·7 ha in the Tanakami Mountains, central Japan. We found that the contribution of the hillslope unit type to small catchment runoff varied with the magnitude of rainfall. When the total amount of rainfall for a single storm event was < 35 mm, runoff in the small catchment was predominantly generated from the side slope. As the amount of rainfall increased (>35 mm), the valley‐head also began to contribute to the catchment runoff, adding to runoff from the side slope. Although the direct runoff from the valley‐head was greater than that from the side slope, the contribution from the side slope was quantitatively greater than that from the valley‐head due to the proportionally larger area occupied by the side slope in the small catchment. The storm runoff responses of the small catchments reflected the change in the runoff components of each hillslope unit as the amount of rainfall increased and rainfall patterns changed. However, similar runoff responses were found for the small catchments with different areas. The similarity of the runoff responses is attributable to overlay effects of different hillslope units and the similar composition ratios of the valley‐head and side slope in the catchments. This study suggests that the relative roles of the valley‐head and side slope are important in runoff generation and solute transport as the catchment size increases from a hillslope/headwater to a small catchment. Copyright © 2011 John Wiley & Sons, Ltd.     

Estimating the deep seepage component of the hillslope and catchment water balance within a measurement uncertainty framework

Deep seepage is a term in the hillslope and catchment water balance that is rarely measured and usually relegated to a residual in the water balance equation. While recent studies have begun to quantify this important component, we still lack understanding of how deep seepage varies from hillslope to catchment scales and how much uncertainty surrounds its quantification within the overall water balance. Here, we report on a hillslope water balance study from the H. J. Andrews Experimental Forest in Oregon aimed at quantifying the deep seepage component where we irrigated a 172‐m² section of hillslope for 24·4 days at 3·6 ± 3 mm/h. The objective of this experiment was to close the water balance, identifying the relative partitioning of, and uncertainties around deep seepage and the other measured water balance components of evaporation, transpiration, lateral subsurface flow, bedrock return flow and fluxes into and out of soil profile storage. We then used this information to determine how the quantification of individual water balance components improves our understanding of key hillslope processes and how uncertainties in individual measurements propagate through the functional uses of the measurements into water balance components (i.e. meteorological measurements propagated through potential evapotranspiration estimates). Our results show that hillslope scale deep seepage composed of 27 ± 17% of applied water. During and immediately after the irrigation experiment, a significant amount of the irrigation water could not be accounted for. This amount decreased as the measurement time increased, declining from 28 ± 16% at the end of the irrigation to 20 ± 21% after 10 days drainage. This water is attributed to deep seepage at the catchment scale. Copyright © 2010 John Wiley & Sons, Ltd.     

Supra‐glacial deposition and flux of catastrophic rock–slope failure debris,south‐central Alaska

The ongoing debate over the effects of global environmental change on Earth's cryosphere calls for detailed knowledge about process rates and their variability in cold environments. In this context, appraisals of the coupling between glacier dynamics and para‐glacial erosion rates in tectonically active mountains remain rare. We contribute to filling this knowledge gap and present an unprecedented regional‐scale inventory of supra‐glacial sediment flux and hillslope erosion rates inferred from an analysis of 123 large (> 0·1 km²) catastrophic bedrock landslides that fell onto glaciers in the Chugach Mountains, Alaska, as documented by satellite images obtained between 1972 to 2008. Assuming these supra‐glacial landslide deposits to be passive strain markers we infer minimum decadal‐scale sediment yields of 190 to 7400 t km^–2 yr^–1 for a given glacier‐surface cross‐section impacted by episodic rock–slope failure. These rates compare to reported fluvial sediment yields in many mountain rivers, but are an order of magnitude below the extreme sediment yields measured at the snouts of Alaskan glaciers, indicating that the bulk of debris discharged derives from en‐glacial, sub‐glacial or ice‐proximal sources. We estimate an average minimum para‐glacial erosion rate by large, episodic rock–slope failures at 0·5–0·7 mm yr^–1 in the Chugach Mountains over a 50‐yr period, with earthquakes likely being responsible for up to 73% of this rate. Though ranking amongst the highest decadal landslide erosion rates for this size of study area worldwide, our inferred rates of hillslope erosion in the Chugach Mountains remain an order of magnitude below the pace of extremely rapid glacial sediment export and glacio‐isostatic surface uplift previously reported from the region. Copyright © 2012 John Wiley & Sons, Ltd.     

The role of chronic and episodic disturbances on channel–hillslope coupling: the persistence and legacy of extreme floods

Landscape form represents the cumulative effects of de‐stabilizing events relative to recovery processes. Most geomorphic research has focused on the role of episodic rare events on landscape form with less attention paid to the role and persistence of chronic inputs. To better establish the interplay between chronic and episodic extreme events at regional scales, we used aerial photography and post‐flood sediment sampling to assess stream and hillslope response and recovery to a 100–300 yr. flood caused by Tropical Storm Irene in New England. Within a 14 000 km² study area, analysis of aerial photographs indicated that the storm initiated (n = 534) and reactivated (n = 460) a large number of landslides. These landslides dramatically increased overall estimates of regional erosion rates (from 0.0023 mm/yr. without Irene to 0.0072 mm/yr. with Irene). Similarly, Irene‐generated LWD inputs of 0.25–0.5 trees/km exceeded annual background rates in a single event, and these concentrated inputs (10¹–10² of trees/landslide) are likely to result in large jams and snags that are particularly persistent and geomorphically effective. Finally, we found that landslide scars continue to provide elevated sediment inputs years after the event, as evidenced by sustained higher suspended sediment concentrations in streams with Irene‐generated landslides. Overall, our results indicate that infrequent, high‐magnitude events have a more important geomorphic role in tectonically stable, more moderate‐relief systems than has been previously recognized. Understanding the role of these events has particular relevance in regions such as New England, where the frequency and magnitude of extreme storms is expected to increase. Further, these effects may force reconsideration of conservation and restoration targets (for example in channel form and large wood loading and distribution) in fluvial systems. Copyright © 2016 John Wiley & Sons, Ltd.     

Sediment transport,redistribution and storage on logged forest hillslopes in south‐eastern Australia

Post‐logging changes in catchment sediment yield have traditionally been attributed to increases in hillslope erosion and delivery rates as a result of forest harvesting activities. Linking hillslope erosion to catchment yield in forestry environments remains difficult, however, primarily because of the scarcity of data on the nature of hillslope sediment storage and delivery processes. A large rainfall simulator (350 m²) was used to apply rainstorms to a logged hillslope containing a snig track (skid trail) and a general logging or harvesting area (GHA) on 10 forest compartments in south‐eastern Australia. The experiments confirmed that the compacted, disturbed surfaces, such as roads and tracks, are the dominant sources of sediment in forestry areas. Sediment transport rates were limited by available sediment supply on both the snig track and the GHA, introducing important implications for the modelling of these surfaces using sediment transport capacity theories. Sediment delivery from the snig track to the adjacent GHA, via a cross‐bank (drainage diversion), was strongly influenced by the percentage fine fraction in the eroded sediment. Preferential deposition of coarse aggregates was measured at erosion control structures and on the adjacent GHA. Over 50% of fine‐grained material were deposited on the hillslope over a relatively short, flow path length of <5 m, highlighting the effectiveness of runoff diversion as a practice in reducing sediment flux. The transfer of water and sediment from disturbed to less disturbed parts of the landscape, and the associated potential for sediment storage, needs to be considered as part of any catchment impact assessment. Copyright © 1999 John Wiley & Sons, Ltd.     

Using sediment travel distance to estimate medium‐term erosion rates: a 16‐year record

Fine grained (80 µm) magnetite was introduced onto a semi‐arid grassland hillslope in 1992, as part of a set of rainfall‐simulation experiments. Using measurements of magnetic susceptibility, the median distance travelled by these magnetite grains during subsequent natural runoff events in the 16‐year period up to 2008 was estimated. Coupling this estimate to direct measurements of sediment flux obtained during the rainfall‐simulation experiments has enabled estimation of the erosion rate over this period. The estimated average erosion rate of between 2·61 × 10^?2 and 4·36 × 10^?2 kg m^?1 year^?1, is equivalent to a rate of ground lowering between 0·020 and 0·033 mm year^?1. This estimate is consistent with (in the sense of being less than) an estimate of total sediment detachment over the same period. The rate of erosion measured using this travel‐distance approach is an order of magnitude less that obtained from a study based on ¹³⁷Cs in a nearby catchment, and compatible with the longevity of continents. Copyright © 2010 John Wiley & Sons, Ltd.     

Interpreting erosion rates from cosmogenic radionuclide concentrations measured in rapidly eroding terrain

A combination of numerical analysis and ¹⁰Be concentrations measured in sediment samples from the high‐relief Torrente catchment, southern Spain, allows us to investigate the sampling requirements for determining erosion rates using cosmogenic nuclides in high‐relief, landslide‐dominated terrain. We use simple modelling to quantify the effect of particle spalling and/or landsliding on erosion rates determined using a cosmogenic in‐situ produced isotope. Analytical results show that the cosmogenic nuclide concentration of a surface experiencing regular detachment of a grain or block may be considered to be in steady state, and ‘in‐situ’ erosion rates estimated, when an appropriate number of spatially independent samples are amalgamated. We present equations that enable calculation of the number of bedrock samples that must be amalgamated for the estimation of mean erosion rates on an outcrop experiencing regular detachment of a grain or chip of thickness L every T years. Our findings confirm that mean catchment erosion rates may be reliably estimated from ¹⁰Be concentrations in fluvial sediment in high‐relief rapidly eroding terrain. These catchment‐wide integrated erosion rates can be calculated where erosion is primarily accomplished through shallow (<3 m) spalling processes; where deep‐seated (>3 m) landslides are the dominant mode of erosion only minimum erosion rates can be determined. Lastly, we present erosion rate measurements from the Torrente catchment that reveal variation of two orders of magnitude (0·03–1·6 m ka^?1) quantifying the high degree of spatial variation in erosion rates expected within rapidly uplifting catchments. Copyright © 2006 John Wiley & Sons, Ltd.     

Ground‐based thermal imagery as a simple,practical tool for mapping saturated area connectivity and dynamics

The hillslope‐riparian‐stream system is a key functional unit of catchments, yet very difficult to measure and monitor due to its tremendous complexity and high spatio‐temporal variability. Here, we present a simple and practical tool for imaging directly these hillslope‐riparian‐area connections. We used a FLIR b50 infrared camera to produce thermal images at the scale of 140 × 140 pixels over the spectral range 7·5–13 µm. Our IR imaging technique is sensitive to the upper 0·1 mm of the water column. Images were obtained from a constant position on the right bank of the Weierbach catchment in Luxembourg, at an incidence angle of approximately 45° over a 5‐week period. The study site measured 5 × 3 m. Our results show that ground‐based IR imagery can discriminate between areas with snow cover, snow melt, soil seepage, and stream water. More importantly, it can detect when and where variably saturated areas are active and when connectivity exists between the hillslope–riparian–stream system. Our proof of concept suggests that this is a simple, inexpensive technology for sequential mapping and characterisation of surface saturated areas and a useful complement to conventional tracer techniques. Copyright © 2010 John Wiley & Sons, Ltd.     

Gully catchments as a sediment sink,not just a source: Results from a long‐term (~12 500 year) sediment budget

Sediment delivery from hillslopes to trunk streams represents a significant pathway of mass transfer in the landscape, with a large fraction facilitated by gully systems. The internal gully geomorphic dynamics represent a considerable gap in many landscape and empirical erosion models, therefore a better understanding of these processes over longer timescales (10–10⁴ years) is needed. This study analyses the sediment mass balance and storage dynamics within a headwater gully catchment in central Europe over the last ~12 500 years. Human induced erosion resulted in hillslope erosion rates ~2.3 times higher than under naturally de‐vegetated conditions (during the Younger Dryas), however the total sediment inputs to the gully system (and therefore gully aggradation), were similar. Net gully storage has consistently increased to become the second largest term in the sediment budget after hillslope erosion (storage is ~45% and ~73% of inputs during two separate erosion and aggradation cycles). In terms of the depletion of gully sediment storage, the sediment mass balance shows that export beyond the gully fan was not significant until the last ~500 years, due to reduced gully fan accommodation space. The significance of storage effects on the gully sediment mass balance, particularly the export terms, means that it would be difficult to determine the influences of human impact and/or climatic changes from floodplain or lake sedimentary archives alone and that the sediment budgets of the headwater catchments from which they drain are more likely to provide these mechanistic links. Copyright © 2015 John Wiley & Sons, Ltd.     

The topographic signature of a major typhoon

In August 2009, the typhoon Morakot, characterized by a cumulative rainfall up to 2884 mm in about three days, triggered thousands of landslides in Taiwan. The availability of LiDAR surveys before (2005) and after (2010) this event offers a unique opportunity to investigate the topographic signatures of a major typhoon. The analysis considers the comparison of slope–area relationships derived by LiDAR digital terrain models (DTMs). This approach has been successfully used to distinguish hillslope from channelized processes, as a basis to develop landscape evolution models and theories, and understand the linkages between landscape morphology and tectonics, climate, and geology. We considered six catchments affected by a different degree of erosion: three affected by shallow and deep‐seated landslides, and three not affected by erosion. For each of these catchments, 2 m DTMs were derived from LiDAR data. The scaling regimes of local slope versus drainage area suggested that for the catchments affected by landslides: (i) the hillslope‐to‐valley transitions morphology, for a given value of drainage area, is shifted towards higher value of slopes, thus indicating a likely migration of the channelized processes and erosion toward the catchment boundary (the catchment head becomes steeper because of erosion); (ii) the topographic gradient along valley profiles tends to decrease progressively (the valley profile becomes gentler because of sediment deposition after the typhoon). The catchments without any landslides present a statistically indistinguishable slope–area scaling regime. These results are interesting since for the first time, using multi‐temporal high‐resolution topography derived by LiDAR, we demonstrated that a single climate event is able to cause significant major geomorphic changes on the landscape, detectable using slope–area scaling analysis. This provides new insights about landscape evolution under major climate forcing. Copyright © 2015 John Wiley & Sons, Ltd.     

The topographic imprint of a transient climate episode: the western Andean flank between 15·5° and 41·5°S

Mountain‐range topography is determined by the complex interplay between tectonics and climate. However, often it is not clear to what extent climate forces topographic evolution and how past climatic episodes are reflected in present‐day relief. The Andes are a tectonically active mountain belt encompassing various climatic zones with pronounced differences in rainfall, erosion, and glacier extent under similar plate‐boundary conditions. In the central to south‐western Andes, climatic zones range from hyperarid desert with mean annual rainfall of 5 mm/a (22·5°S) to year‐round humidity with 2500 mm/a (40°S). The Andes thus provide a unique setting for investigating the relationship between tectonics, climate, and topography. We present an analysis of 120 catchments along the western Andean watersheds between 15·5° and 41·5°S, which is based on SRTMV3‐90m data and new medium‐resolution rainfall, tropical rainfall measurement mission (TRMM) dataset. For each basin, we extracted geometry, relief, and climate parameters to test whether Andean topography shows a climatic imprint and to analyze how climate influences relief. Our data document that elevation and relief decrease with increasing rainfall and descending snowline elevation. Furthermore, we show that local relief reaches high values of 750 m in a zone between 28°S to 35°S. During Pleistocene glacial stages this region was affected by the northward shifting southern hemisphere Westerlies, which provided moisture for valley‐glacier formation and extended glacial coverage as well as glacial erosion. In contrast, the southern regions between 35°S to 40°S receive higher rainfall and have a lower local relief of 200 m, probably related to an increased drainage density. We distinguish two different, climatically‐controlled mechanisms shaping topography: (1) fluvial erosion by prolonged channel‐hillslope coupling, which smoothes relief, and (2) erosion by valley glaciers that generates relief. Finally, Our results suggests that the catchment‐scale relief of the Andes between 28°S to 35°S is characterized by a pronounced transient component reflecting past climatic conditions. Copyright © 2010 John Wiley & Sons, Ltd.