Cyclic and post-cyclic shear behavior of low-plasticity silt with varying clay content

This paper investigates the cyclic and post-cyclic shear behavior of low-plasticity silt and the impact of additional clay content. Bentonite clay was added to the low-plasticity Mississippi River Valley (MRV) silt (PI=6) to increase the clay content of the soil. A series of triaxial tests were conducted in the laboratory to examine the shear and pore pressure behavior during and after cyclic loading. As the bentonite content in the reconstituted specimens increased, the excess pore pressure developed at a slower rate and the total excess pore pressure decreased at the end of cyclic loading. In contrast to the MRV silt, the specimens modified with bentonite experienced cyclic softening rather than initial flow liquefaction. The cyclic shear strength increased with an increase in bentonite content. The post-cyclic reconsolidation behavior was a similar to a virgin compression process, and not recompression. Adding bentonite to the MRV silt results in changes in permeability, compressibility, undrained shear strength, and initial stiffness. Additionally, the cyclic loading had a marked effect on the shear behavior of low-plasticity soil with a PI<6, but not noticeable with a PI>6. This study suggests that the behavior of the Mississippi River Valley silt changes from contractive sand-like material to clay-like behavior at a PI≈6 due to the addition of clay.     

Postcyclic behavior of low-plasticity silt with limited excess pore pressures

This paper investigates the postcyclic behavior of low-plasticity silt with excess pore pressure ratio (R_u) less than 1. The testing specimens were prepared from Mississippi River Valley (MRV) silt. Full and no reconsolidation were allowed after specimens were subjected to various excess pore pressure ratios due to cyclic loading in a cyclic triaxial cell, and then monotonic shear tests were conducted. The effect of the R_u on shear strength and stiffness at small and large deformation was investigated. It was found that a R_u greater than 0.70 is a prerequisite of large increase in volumetric strain and undrained shear strength for specimens with full reconsolidation. In contrast, a significant decrease in yield shear strength and initial stiffness was noted for specimens without reconsolidation. In comparison to published data for sands, the silt experienced significant volumetric strain due to reconsolidation at lower R_u, indicating that the specimen fabric was modified or strained at lower R_u.     

Cyclic shear response of channel-fill Fraser River Delta silt

The cyclic shear response of a channel-fill, low-plastic silt was investigated using constant-volume direct simple shear testing. Silt specimens, initially consolidated to stress levels at or above the preconsolidation stress, displayed cyclic-mobility-type strain development during cyclic loading without static shear stress bias. Liquefaction in the form of strain softening accompanied by loss of shear strength did not manifest regardless of the applied cyclic stress ratio, or the level of induced excess pore water pressure, suggesting that the silt is unlikely to experience flow failure under cyclic loading. The cyclic shear resistance of the silt increased with increasing overconsolidation ratio (OCR) for OCR>1.3. The silt specimens that experienced high equivalent excess cyclic pore water pressure ratios (r_u>80%) resulted in considerable volumetric strains (2.5%–5%) during post-cyclic reconsolidation implying potentially significant changes to the particle fabric under cyclic loading.     

Effect of non-plastic silt content on the liquefaction behavior of sand–silt mixture

To identify the effect of non-plastic silt on the cyclic behavior of sand–silt mixtures, total sixty undrained cyclic triaxial stress-control tests were carried out on sand–silt mixtures. These tests were conducted on specimens of size 71 mm diameter and 142 mm height with a frequency of 1 Hz. Specimens were prepared at a constant relative density and constant density approach. The effect of relative density, confining pressure as well as magnitude of cyclic loading was also studied. For a constant relative density (D_r=60%) the effect of limiting silt content, pore pressure response and cyclic strength was observed. The rate of generation of excess pore water pressure with respect to cycles of loading was found to initially increase with increase in silt content till the limiting silt content and thereafter it reverses its trend when the specimens were tested at a constant relative density. The cyclic resistance behavior was observed to be just opposite to the pore pressure response. Permeability, CRR and secant shear modulus decreased till limiting silt content; after that they became constant with increasing silt content.     

Cyclic resistance and liquefaction behavior of silt and sandy silt soils

The liquefaction behavior and cyclic resistance ratio (CRR) of reconstituted samples of non-plastic silt and sandy silts with 50% and 75% silt content are examined using constant-volume cyclic and monotonic ring shear tests along with bender element shear wave velocity (V_s) measurements. Liquefaction occurred at excess pore water pressure ratios (r_u) between 0.6 and 0.7 associated with cumulative cyclic shear strains (γ) of 4% to 7%, after which cyclic liquefaction ensued with very large shear strains and excess pore water pressure ratio (r_u>0.8). The cyclic ring shear tests demonstrate that cyclic resistance ratio of silt and sandy silts decreases with increasing void ratio, or with decreasing silt content at a certain void ratio. The results also show good agreement with those from cyclic direct simple shear tests on silts and sandy silts. A unique correlation is developed for estimating CRR of silts and sandy silts (with more than 50% silt content) from stress-normalized shear wave velocity measurements (V_s1) with negligible effect of silt content. The results indicate that the existing CRR–V_s1 correlations would underestimate the liquefaction resistance of silts and sandy silt soils.     

Cyclic response of saturated silts

Softening and strength loss of sands with increasing excess pore water pressure under repeated loads is well-known. However, extensive damage to the built environment also occurs at the sites underlain by fine grained soils during seismic shaking. The primary objective of this study is to investigate the factors affecting cyclic behavior of saturated low-plastic silt through laboratory testing. For this purpose, an extensive laboratory testing program including conventional monotonic and cyclic triaxial tests was carried out over reconstituted silt samples. The effects of the inherent soil properties and the effects of loading characteristics on the cyclic response of saturated low-plastic reconstituted silt samples were examined separately. Based on the test results, a model was introduced to estimate the effect of initial shear stress on the cyclic response. Besides, liquefaction susceptibility of the samples was examined via current liquefaction susceptibility criteria.     

The effect of plastic fines on the pore pressure generation characteristics of saturated sands

Pore water pressure generation during earthquake shaking initiates liquefaction and affects the shear strength, shear stiffness, deformation, and settlement characteristics of soil deposits. The effect of plastic fines (kaolinite) on pore pressure generation in saturated sands was studied through strain-controlled cyclic triaxial tests. In addition to pore pressure generation, this experimental study also focused on evaluating the threshold shear strain for pore pressure generation and the volumetric compressibility of specimens during pore pressure dissipation. The results reveal that specimens having up to 20% plastic fines content generated larger values of pore water pressure than clean sand specimens. At 30% fines content, the excess pore water pressure decreased below that of clean sand. The threshold shear strain, which indicates the strain level above which pore pressures begin to generate, was assessed for different kaolinite–sand mixtures. The threshold shear strain was similar for 0–20% fines (γ_t0.006–0.008%), but increased to about 0.025% for 30% fines. The volumetric compressibility, measured after pore pressure generation, was similar for all specimens. The transition of behavior at fines contents between 20% and 30% can be attributed to a change in the soil structure from one dominated by sand grains to one dominated by fines.     

Evolution of the shear wave velocity during shaking modeled in centrifuge shaking table tests

Two in-flight shear wave velocity measurement systems were developed to perform the subsurface exploration of shear wave velocity in a centrifuge model. The bender elements test and the pre-shaking test used in the study provided reliable and consistent shear wave velocity profiles along the model depth before and after shaking in the centrifuge shaking table tests. In addition, the use of the bender elements measurement system particularly developed here allowed continuous examination of the evolution of shear wave velocity not only during and after the shaking periods in the small shaking events but also during the dissipation period of excess pore water pressure after liquefaction in the large shaking events. The test results showed that the shear wave velocity at different values of excess pore water pressure ratio varied as the effective mean stress to the power of 0.27, to a first approximation. Consequently, a relationship between the shear wave velocity evolution ratio and the excess pore water pressure ratio is proposed to evaluate the changes in shear wave velocity due to excess pore water generation and dissipation during shaking events. This relation will assist engineers in determining the shear stiffness reduction ratio at various r_u levels when a sand deposit is subjected to different levels of earthquake shaking.     

压实度对脱硫石膏动强度和动孔压影响试验

为研究压实度对脱硫石膏动强度与动孔压特性影响，对压实度为0.85、0.90和0.95三组脱硫石膏进行等压固结不排水振动三轴试验，试验围压为100 kPa、200 kPa和400 kPa。结果表明：随压实度增大，脱硫石膏颗粒间作用力愈强，颗粒联结骨架越不容易破坏，脱硫石膏动强度越大，动孔压增长越慢；试验压实度范围下，脱硫石膏动剪应力比和动内摩擦角均与压实度呈线性相关；试验用脱硫石膏可分类定名为低液限粉土，其动强度曲线和动孔压发展模式均与常规粉土类似，分别可通过幂函数和对数函数表征，经F值试验法检验，其统计回归显著性水平均为"高度显著"。     

Cyclic undrained behavior of silty sand

Laboratory cyclic triaxial tests were performed to investigate the effect of fine content on the pore pressure generation in sand. Strain-controlled, consolidated undrained tests have been performed with a cyclic shear strain range of 0·015-1·5%. These tests were carried to 1000 cycles or to initial liquefaction, which ever occurred first. Triaxial tests were performed on pure sand silt specimens and specimens with silt additions of 10, 20, 30, and 60% by weight. Two types of silt, a non-plastic silt and a low plasticity silt (PI 10) were used as control materials. The main parameters varied in this study were the amount of silt, the plasticity index of silt, and the void ratio where the observed parameter was the pore pressure generation. For all silt contents, silt plasticity and the number of loading cycles have no significant effect at strain levels below 0·01%. Therefore, threshold strain for silty sands have approximately the same value as sands. For both non-plastic and low plasticity silts, there is a significant increase in the generated pore pressure at high strain levels.     

Investigation of liquefaction and pore water pressure development in layered sands

This paper presents the results of shaking table model tests which were carried out to investigate the pore water pressure generation and related liquefaction mechanism in layered sand deposits. The experiments were performed on uniform sand columns, silt interlayered sand columns and two layered sand columns deposited at various relative densities and subjected to different input excitations. During the experiments excess pore water pressures were measured by pore pressure transducers installed at three different depths and, surface settlements and thickness of water film developed under less permeable inclusions were measured by a digital camera. The experimental results are discussed and compared to demonstrate the effects of relative density, input acceleration and presence of a silt seam on the generation of excess pore water pressure in sand deposits subjected to dynamic loading. The results showed that the presence of a less permeable silt interlayer within the sand deposit and existence of a loose sand layer underlying dense sand deposits can have significant effect on the pore water pressure generation mechanism.     

颗粒组成对粉土动强度的影响分析

以天津汉沽地区某挡土墙地基粉土为研究对象,首先对不同颗粒组成的粉土做固结不排水动三轴剪切试验,采用各向等压固结,周围压力等于100kPa。固结完成后在不排水条件下施加轴向激振力,试验波形为正弦波,振动频率1.0Hz,试验中以试样在周期剪切时轴向周期应变达到5%作为破坏标准,得出粉土的动强度受颗粒组成的影响。细颗粒含量越大,其动强度越小,黏粒含量为7.2%的粉土循环剪应力比CSR约为20.3%黏粒含量粉土的2倍。粉土的动强度可以用循环剪应力比和破坏振次建立的幂函数关系式较好地拟合。在剪切过程中,粉土的孔隙水压力一直没有达到所施加的围压数值,最终稳定在75%~85%围压之间。同时,试验还得出孔隙水压力的增长模式不能用统一的Seed模型拟合,孔压增长规律的影响因素较多。     

沙土在孔隙水注入实验中渗透剪切破坏

前人曾指出液化后伴随着超孔隙水压重新分配的渗透会引起流体破坏的可能性。为了研究这一现象,利用实验室三轴试验将孔隙水注入土壤检测了土壤的渗透剪切破坏。该实验是在各项异性的固结作用后保持差应力,使用孔隙水控制装置在体积不变的应变控制条件下将孔隙水注入。实验中所用的材料是在1995年神户地震时被液化的常规洁净细砂和风化的花岗岩土壤。本文以实验结果为基础,讨论了由孔隙水注入引起的渗透剪切破坏判据和导致后液化行为的剪切应变发展特征。     

Seismic loading impacts on excess pore‐water pressure maintain landslide triggered flowslides

During the 2003 Sanriku‐Minami earthquake, Japan, a flowslide was triggered on a slope of about 13.5º. The displaced landslide mass developed into a flowslide and deposited on a horizontal rice paddy after traveling approximately 130 m. To study the trigger and movement mechanisms of this landslide, field investigation and laboratory ring‐shear tests were performed. Field investigation revealed that the landslide originated from a fill slope, where a gully was buried for cultivation some decades ago, and shallow ground water was present. Undrained monotonic and cyclic ring‐shear tests on a sample (pyroclastic deposits) taken from the source area revealed that the soil is highly liquefiable, and its steady‐state shear strength can be little affected by overconsolidation. Using the seismic records of the earthquake, probable seismic loadings on the sliding surface were synthesized and applied to the samples in ring‐shear tests, which were performed under undrained or partially drained conditions. The undrained and partially drained tests revealed that shear failure can be triggered by the introduction of seismic loading and formation of excess pore‐water pressure. The generation of excess pore‐water pressure along with increase of shear displacement and the inhibited dissipation of excess pore‐water pressure due to the thickness of the saturated soil layer above the sliding surface probably enabled the continued post‐failure landsliding. Copyright © 2008 John Wiley & Sons, Ltd.     

徐州市棠张镇饱和粉土液化性能试验研究

徐州市棠张镇高速铁路路基的粉土粘粒含量少于1．5％、粉粒含量约为80％,在强烈地震作用下存在着液化可能性,为了分析该路基粉土的液化特性,进行了多组振动三轴液化试验。对试验结果进行分析发现,该地区的粉土振动孔压发展模式与Seed提出的用反正弦三角函数拟合的砂十振动孔压发展模式不同,可以用双曲线进行拟合。采用最大往返剪切作用面上的应力条件确定了该地区的孔压发展模式的拟合参数,为该地区粉土地震液化动力计算分析提供了所需的地震孔隙水压力增长模型。同时,本文指出粉土的密度和结构是振动孔压发展的重要影响因素。     

Energy approach to unsaturated cyclic strength of sand

The mechanical response to cyclic loading of saturated cohesionless soils is usually investigated by means of effective stress method considering pore water pressure changes that lead to reduced strength and stiffness. On the other hand, the behavior of partially saturated sands is different from the behavior of saturated sand deposits. The development of negative pore water pressures in particular makes it difficult to estimate the behavior of partially saturated sands. The response of partially saturated sands, however, can be examined in a physically understandable manner by investigating their energy characteristics independently of pore pressure behavior. To establish a general framework for understanding the behavior of partially saturated sand, a total of 52 resonant column and dynamic torsional shear tests were conducted under undrained conditions. The effects of factors such as the amplitude of shear strain, relative density, saturation ratio and confining pressure on the dynamic characteristics of the sand and on energy dissipation were studied. The use of the energy concept in the evaluation of partially saturated soils is shown to be a promising method for the evaluation of the cyclic behavior of partially saturated sands.     

Undrained monotonic and cyclic behavior of sand-ground rubber mixtures

In this study the stress–strain characteristics of sand-ground rubber mixtures are investigated in the sandlike zone,at different confining pressures,using hollow cylinder specimens subjected to torsional monotonic and cyclic loading.Under monotonic loading a mixture of sand-ground rubber with 10% and 25% rubber content show more contraction behaviour than that observed in a pure sand specimen.Phase transformation point in these mixtures are located on a larger shear strain.As expected,the shear strength of specimens decreases with increase of ground rubber content.However,with increasing of effective confining pressure,the loss in shear strength of the mixture is decreased.In addition,a mixture with 25% ground rubber shows a smaller loss in shear strength compared to a mixture with 10% ground rubber mixture.Under cyclic loading mixtures with 10% and 25% ground rubber have similar liquefaction resistance,especially at confining pressures of 110 k Pa and 260 k Pa.Therefore,by using of the mixture with 25% ground rubber,a larger volume of scrap tires could be recycled.The addition of ground rubber to sand would affect the shear strain variation and excess pore water pressure trends,and this effect was further intensified with increasing ground rubber percentage.     

An example of slip instability resulting from displacement-varying strength

A rock cylinder, containing a clay-filled sawcut making an angle of 30° to the sample axis, was deformed at constant confining and pore pressures and constant remote shortening rate. The sawcut surfaces contained a series of regularly spaced ridges and grooves oriented perpendicular to the direction of shear. The interaction of these grooved surfaces resulted in a sliding strength which varied periodically with displacement. By varying the effective machine stiffness through the use of an electronic feedback circuit, a range of stable and unstable slip behavior was achieved. In this way, we examined fault slip behavior which was dominated by displacement-dependent strength.     

Learning of pore pressure response and dynamic soil behavior from downhole array measurements

Downhole arrays are deployed to measure motions at the ground surface and within the soil profile, with some arrays instrumented to also record the pore pressure response within soft soil profiles during excitation. The measurements from these arrays have typically been used in conjunction with parametric and nonparametric inverse analysis approaches to identify soil constitutive model parameters for use in site response analysis or to identify averaged soil behavior between locations of measurement. The self-learning simulations (SelfSim) inverse analysis framework, previously developed and applied under total stress conditions, is extended to effective stress considerations and is employed to reproduce the measured motions and pore pressures from downhole arrays while extracting the underlying soil behavior and pore pressure response of individual soil layers. SelfSim is applied to the 1987 recordings from the Imperial Valley Wildlife Liquefaction Array. The extracted soil behavior suggests a new functional form for modeling the degradation of the shear modulus with respect to excess pore pressures. The extracted pore pressure response is dependent on the number and amplitude of shear strain cycles and has a functional form similar to current strain-based pore pressure generation models.     

Triggering Mechanisms of Slope Instability and their Relationship to Earthquakes and Tsunamis

— Submarine and shoreline slope failures that accompany large earthquakes and large tsunamis are triggered by several mechanisms. Triggering mechanisms range from direct effects, such as inertial forces from earthquake shaking, to indirect effects, such as rapid drawdown that occurs when an earthquake-generated tsunami first approaches a shoreline. Soil shear strength also plays an important role in earthquake-related slope failures. Earthquakes change the shear strength of the soil by inducing excess pore water pressures. These excess pore water pressures change with time after the earthquake, resulting in changes in shear strength and slope stability with time. This paper reviews earthquake-related triggering mechanisms for submarine and shoreline slope failures. The variation in shear strength with time following an earthquake is examined and it is shown that delayed slope failures after an earthquake can occur as a result of changes in earthquake-induced excess pore water pressures and shear strength with time.