Vibration characterization of fully-closed high speed railway subgrade through frequency: Sweeping test

This paper presents the vibration characteristics of a new type fully-closed railway subgrade (FCRS) through field frequency – sweeping test. The FCRS, which uses semi-grid modified cement-based compound material as waterproof layer, is designed to solve serious subgrade damage problems induced by expansive soil. Dynamic stress sensors and accelerometers were installed at various locations in FCRS to monitor dynamic response. The results show that the attenuation regularities of dynamic stress and acceleration along subgrade depth were significantly affected by excitation frequency and semi-grid waterproof layer. The pronounced frequency of FCRS investigated in this paper was gently influenced by its layer system, and gradually changed from 20 Hz to 22 Hz as depth increased.     

MEMS型加速度传感器在超高层建筑振动监测中的性能对比测试

为开展MEMS型加速度传感器在超高层建筑振动监测应用中的性能对比测试,选取4种不同类型MEMS型加速度传感器与G1B型力平衡式加速度传感器,将其安装在地王大厦相同测点,对MEMS型、G1B型加速度传感器记录的结构环境振动数据进行时程、频谱和模态频率对比分析,并对其记录的结构地震响应进行时域及频域对比。研究结果表明,不同类型MEMS型加速度传感器仪器噪声均大于G1B型加速度传感器,其中MEMS-I型加速度传感器噪声水平相对较小,与G1B型加速度传感器模态频率识别结果及地震响应监测数据吻合较好,验证了MEMS-I型加速度传感器可较准确地记录到结构强振动响应,适用于超高层建筑日常结构振动监测。     

Seismic response of retaining walls with cohesive backfill: Centrifuge model studies

Observations from recent earthquakes show that retaining structures with non-liquefiable backfills perform extremely well; in fact, damage or failures related to seismic earth pressures are rare. The seismic response of a 6-m-high braced basement and a 6-m free-standing cantilever wall retaining a compacted low plasticity clay was studied in a series of centrifuge tests. The models were built at a 1/36 scale and instrumented with accelerometers, strain gages and pressure sensors to monitor their response. The experimental data show that the seismic earth pressure on walls increases linearly with the free-field PGA and that the earth pressures increase approximately linearly with depth, where the resultant acts near 0.33 H above the footing as opposed to 0.5–0.6 H, which is suggested by most current design methods. The current data suggest that traditional limit equilibrium methods yield overly conservative earth pressures in areas with ground accelerations up to 0.4g.     

Impact and cyclic shaking on loose sand properties in laminar box using gap sensors

This paper focuses on using high-frequency GAP-SENSORs (GSs), accelerometers, and load cells in a laminar shear box (LSB) filled with loose Toyoura sand to understand the effects of impact loads and cyclic shaking at 1-G on soil properties. The shear wave velocity at small strain (V_s) was calculated directly from first arrival reference using displacement time-history of two GSs under impact loading. Moreover, from first peak using the reduced deformation amplitude technique, damping ratio was calculated. In addition, shaking table tests were performed under harmonic loading with amplitude of acceleration inside the model ground varying from 0.02 g to 1 g. The frequencies of excitation varied from 1 Hz to 10 Hz. GSs and inside accelerometers were used to directly measure the outside lateral deformation and shear stress at different elevations of LSB, respectively. Results show that the shear modulus (G) and the damping ratio (D) behavior of model sand are generally consistent with the behavior presented by similar tests using only accelerometers. In addition, damping ratio increases as frequency loading increases. Characteristic changes in two shear stress components in shaking loading conditions were also investigated using high precision inside load cells.     

Preliminary analysis of the connection between ocean dynamics and the noise of gravity tide observed at the Sopronbánfalva Geodynamical Observatory,Hungary

An experimental development of a computer controlled photoelectric ocular system applied for the LaCoste and Romberg G949 gravimeter made the continuous observation of time variation of gravity possible. The system was operated for half a year in the Sopronbánfalva Geodynamical Observatory to test its capabilities. The primary aim of this development was to provide an alternative and self-manageable solution instead of the standard electronic (Capacitive Position Indicator) reading of this type of gravimeter and use it for the monitoring of Earth tide. It, however, turned out that this system is sensitive enough to observe the effect of variable seismic noise (microseisms) due to the changes of ocean weather in the North Atlantic and North Sea regions at microGal level (1 μGal = 10⁻⁸ m/s²). Up to now not much attention was paid to its influence on the quality and accuracy of gravity observations because of the large distance (>1000 km) between the observation place (generally the Carpathian–Pannonian basin) and the locations (centres of storm zones of the northern hydrosphere) of triggering events. Based on an elementary harmonic surface deformation model the noise level of gravity observations was compared to the spectral characteristics of seismic time series recorded at the same time in the observatory. Although the sampling rate of gravity records was 120 s the daily variation of gravity noise level showed significant correlation with the variation of spectral amplitude distribution of the analysed high pass filtered (cut-off frequency = 0.005 Hz) seismograms up to 10 Hz. Also available daily maps of ocean weather parameters were used to support both the correlation analysis and the parameterization of the triggering events of microseisms for further statistical investigations. These maps, which were processed by standard image processing algorithms, provide numerical data about geometrical (distance and azimuth of the storm centres relative to the observation point) and physical (mass of swelling water) quantities. The information can be applied for characterizing the state of ocean weather at a given day which may help the prediction of its influence on gravity measurements in the future. Probably it is the first attempt to analyse quantitatively the effect of ocean weather on gravity observations in this specific area of the Carpathian–Pannonian region.     

1-g Experimental investigation of bi-layer soil response and kinematic pile bending

The effect of soil inhomogeneity and material nonlinearity on kinematic soil–pile interaction and ensuing bending under the passage of vertically propagating seismic shear waves in layered soil, is investigated by means of 1-g shaking table tests and nonlinear numerical simulations. To this end, a suite of scale model tests on a group of five piles embedded in two-layers of sand in a laminar container at the shaking table facility in BLADE Laboratory at University of Bristol, are reported. Results from white noise and sine dwell tests were obtained and interpreted by means of one-dimensional lumped parameter models, suitable for inhomogeneous soil, encompassing material nonlinearity. A frequency range from 0.1 Hz to 100 Hz and 5 Hz to 35 Hz for white noise and sine dwell tests, respectively, and an input acceleration range from 0.015 g to 0.1 g, were employed. The paper elucidates that soil nonlinearity and inhomogeneity strongly affect both site response and kinematic pile bending, so that accurate nonlinear analyses are often necessary to predict the dynamic response of pile foundations.     

Soil anomaly mapping using a caesium magnetometer: Limits in the low magnetic amplitude case

Caesium magnetometers are new tools for soil property mapping with a decimetric resolution [Mathé, V., Lévêque, F., 2003. High resolution magnetic survey for soil monitoring: detection of drainage and soil tillage effects. Earth and Planetary Science Letters 212 (1–2), 241–251]. However, when the magnetic anomalies are only a few nanoteslas (nT), the geologic and pedogenic signal must first be isolated from magnetic disturbances for this method to be useful. This paper investigates the instrumental artifacts and environmental disturbances to adapt the survey protocol to slightly magnetic soils.Among the possible instrumental sources of disturbances listed and quantified, the most significant are: 1) The battery effect upon sensors 2 m away (classic protocol, about ± 0.15 nT) while increasing this distance up to 10 m cancelled it; 2) The noise level of magnetometers and sensors, which, according to tests on two magnetometers and three sensors, rarely and randomly exceeds 0.1 nT, but seems to increase with the electronic component age.Among the environmental disturbances, temporal variations such as diurnal variation or fluctuations linked to the moving of metallic masses play a major role, although the pseudogradient or base-station methods have commonly cancelled them. The efficiency of the latter is strongly dependent on the source nature. However, the ground currents and electromagnetic fields propagating in soils cause more problems. As a first step to better understand such disturbance sources, uncommon magnetic signal variations supposedly due to electromagnetic wave conversions and likely linked to the railway traffic are presented.Based on previous results, an adapted protocol using one magnetometer and two caesium sensors (0.3 and 1.6 m above the surface) is proposed to increase the signal / noise ratio. At first, to maintain an accurate horizontal and vertical location of the sensors, the latter are affixed to a wooden handcart running on plastic rails. Rails adapt to micro-topography, thereby decreasing strongly the soil–sensors distance variations. Anomalies due to topography rarely exceed 0.1 nT. Finally, a method to remove diurnal variations from high-resolution magnetic maps is proposed. Parallel profiles performed successively are adjusted by a cross-profile. Assuming that the temporal variations during each profile are negligible (less than 0.05 nT), this technique, contrary to the pseudogradient, preserves both the decimetric and the metric anomalies (gain of more than 1 nT).     

Processing and interpretation of vintage 2D marine seismic data from the outer Hanö Bay area,Baltic Sea

A grid of previously unpublished, vintage 2D marine seismic lines has been processed and interpreted to the east of Hanö Bay, SW Baltic Sea. The 3200 km² study area lies on the transition between the Hanö Bay Basin to the West and Baltic Synelcise to the East, NE of the Tornquist intra shield tectonic zone.Data from the NA79, NA80 and RW84 surveys were selected for this study from the extensive Oljeprospektering AB (OPAB) Baltic Sea dataset. New processing workflows have been developed for the data which focus on suppressing two significant forms of noise, namely multiple and side scattered noise. Deconvolution in the tau-p domain, parabolic radon demultiple and post stack deconvolution are shown to be effective at attenuating multiple noise, while FK filtering in shot and receiver gathers is effective at removing side scattered noise.The newly processed data were interpreted and a series of maps detailing the structure of the basement, Cambrian and Silurian/Paleozoic horizons were constructed. These maps differ significantly to previously published interpretations of the area. Within the study area, a region of significant Late Carboniferous/Early Permian transtensional faulting and Late Cretaceous inversion is mapped in detail. This structure would have exhibited normal offsets of up to 600 m before inversion with later inverted displacements of up to approximately 200 m in places. This feature appears to extend some 20 km to the SW of the study area to the major fault bounding the Christiansø High. Based on the seismic interpretation, the area appears to have had a similar overall geological history as the adjacent Tornquist Zone to the SW.     

Measuring accelerometer dynamic range from seismic data using Allan deviation

We propose a new approach for calculating the dynamic range of an accelerometer based on an Allan deviation analysis of production seismic data. This test is intended as a field audit technique and does not require an unconditioned dataset from a low‐noise environment. We first show that Allan deviation can measure white noise levels using two commercial accelerometers. The analysis accurately captures the manufacturing noise density specifications and known relationships between white noise, preamplifier gain, and group forming. We then show that a production seismic dataset is suitable for an Allan deviation analysis because the results are not critically affected by a recording filter. Finally, we illustrate the proposed technique by calculating the dynamic range of an accelerometer channel in a seismic streamer using a production dataset.     

Characterizing complex eruptive activity at Santiaguito,Guatemala using infrasound semblance in networked arrays

We implement an infrasound semblance technique to identify acoustic sources originating from volcanic vents and apply the technique to the generally low-amplitude infrasound (< 3 Pa at 1 km) signals produced by Santiaguito dome in Guatemala. Semblance detection is demonstrated with data collected from two-element miniature arrays with ~ 30 m spacing between elements. The semblance technique is effective at identifying a range of eruptive phenomena, including pyroclastic-laden eruptions, vigorous degassing events, and rockfalls, even during periods of high wind contamination Many of the detected events are low in amplitude (tens of mPa) such that they are observed only by select arrays positioned with proximity and line-of-sight to the source. Larger events, such as the pyroclastic-laden eruptions, which occurred bi-hourly in 2009, were detected by all five arrays and produced an infrasonic signal that was correlated across the network. Network correlated events can be roughly located and map to the summit of the Caliente Vent where pyroclastic-laden eruptions originate. In general, the degree of Santiaguito infrasound event correlation is poor across the network, suggesting that complex source geometry contributes to asymmetric sound radiation.     

Low-field variation of magnetic susceptibility as a tool for magnetic mineralogy of rocks

Low-field variation of magnetic susceptibility was investigated on a collection of several hundreds specimens of various minerals and rocks using the KLY-4S Kappabridge. The measurement is fully automated, being executed in 21 distinct fields ranging from 2 to 450 A/m (in one frequency of 875 Hz). The measurement is rapid, 7 min per specimen, so that large collections of specimens can be investigated. The results can be processed both graphically and mathematically. For the latter processing, parameters of two kinds were introduced. One characterizes the susceptibility change with field, the other one characterizes the field in which the susceptibility no longer obeys the Rayleigh law and starts becoming more complex.The results were evaluated statistically. Remarkable differences were revealed between individual minerals and between some rock types. For example, the field variation of susceptibility of pyrrhotite is in general an order of magnitude larger than that of titanomagnetite. The susceptibility increase in pyrrhotite starts at the field an order of magnitude lower than that of titanomagnetite. Low-field variation of susceptibility then appears as an interesting phenomeon that helps in the identification of magnetic minerals and in some cases also in assessing the compositional variation of them.     

Shipping noise in a dynamic sea: a case study of grey seals in the Celtic Sea

Shipping noise is a threat to marine wildlife. Grey seals are benthic foragers, and thus experience acoustic noise throughout the water column, which makes them a good model species for a case study of the potential impacts of shipping noise. We used ship track data from the Celtic Sea, seal track data and a coupled ocean-acoustic modelling system to assess the noise exposure of grey seals along their tracks. It was found that the animals experience step changes in sound levels up to ~ 20 dB at a frequency of 125 Hz, and ~ 10 dB on average over 10–1000 Hz when they dive through the thermocline, particularly during summer. Our results showed large seasonal differences in the noise level experienced by the seals. These results reveal the actual noise exposure by the animals and could help in marine spatial planning.     

Suspended microplastics in the surface water of the Yangtze Estuary System,China: First observations on occurrence,distribution

Levels of microplastics (MPs) in China are completely unknown. This study characterizes suspended MPs quantitatively and qualitatively for the Yangtze Estuary and East China Sea. MPs were extracted via a floatation method. MPs were counted and categorized according to shape and size under a stereomicroscope. The MP densities were 4137.3 ± 2461.5 and 0.167 ± 0.138 n/m³, respectively, in the estuarine and the sea samples. Plastic abundances varied significantly in the estuary. Higher densities in three sea trawls confirmed that rivers were the important sources of MP to the marine environment. Plastic particles (>5 mm) were observed with a maximum size of 12.46 mm, but MPs (0.5–5 mm) constituted more than 90% by number of items. The most frequent geometries were fibres, followed by granules and films. Plastic spherules occurred sparsely. Transparent and coloured plastics comprised the majority of the particles. This study provides clues in understanding the fate and potential sources of MPs.     

Severity of killer whale behavioral responses to ship noise: A dose–response study

Critical habitats of at-risk populations of northeast Pacific “resident” killer whales can be heavily trafficked by large ships, with transits occurring on average once every hour in busy shipping lanes. We modeled behavioral responses of killer whales to ship transits during 35 “natural experiments” as a dose–response function of estimated received noise levels in both broadband and audiogram-weighted terms. Interpreting effects is contingent on a subjective and seemingly arbitrary decision about severity threshold indicating a response. Subtle responses were observed around broadband received levels of 130 dB re 1 μPa (rms); more severe responses are hypothesized to occur at received levels beyond 150 dB re 1 μPa, where our study lacked data. Avoidance responses are expected to carry minor energetic costs in terms of increased energy expenditure, but future research must assess the potential for reduced prey acquisition, and potential population consequences, under these noise levels.     

Transition zone structure under a stationary hot spot: Cape Verde

We report on a two-year seismic deployment in the Cape Verde Islands, one goal of which was to study the upper mantle to determine its structure under a hot spot that is stationary in the hot spot reference frame. We find from analysis of P-to-S receiver functions estimated from broadband seismic recordings that, within uncertainty, the time separation between the 410 and 660 km discontinuities is normal compared to radial earth models. Thus, to exist, even stationary hot spots do not require vertical thermal anomalies from deep melting sources anchored in the lower mantle or at the core–mantle boundary or their anomalies are narrower than ～ 250 km in the upper mantle.     

A coastal three-dimensional water quality model of nitrogen in Jiaozhou Bay linking field experiments with modelling

With anthropogenic changes, the structure and quantity of nitrogen nutrients have changed in coastal ocean, which has dramatically influenced the water quality. Water quality modeling can contribute to the necessary scientific grounding of coastal management. In this paper, some of the dynamic functions and parameters of nitrogen were calibrated based on coastal field experiments covering the dynamic nitrogen processes in Jiaozhou Bay (JZB), including phytoplankton growth, respiration, and mortality; particulate nitrogen degradation; and dissolved organic nitrogen remineralization. The results of the field experiments and box model simulations showed good agreement (RSD = 20% ± 2% and SI = 0.77 ± 0.04). A three-dimensional water quality model of nitrogen (3DWQMN) in JZB was improved and the dynamic parameters were updated according to field experiments. The 3DWQMN was validated based on observed data from 2012 to 2013, with good agreement (RSD = 27 ± 4%, SI = 0.68 ± 0.06, and K = 0.48 ± 0.04), which testifies to the model's credibility.     

Solar activity imprints in tree ring width from Chile (1610–1991)

We have investigated the solar activity signal in tree ring data from two locations in Chile. The tree ring time series extended over a period of ∼400 yr. Spectral and wavelet analysis techniques were employed. We have found evidence for the presence of the solar activity Schwabe (∼11 yr), Hale (∼22 yr), fourth-harmonic of the 208-yr Suess cycle (∼52 yr) and Gleissberg (∼80 yr) cycles. The Gleissberg cycle of tree ring data is in anti-phase with solar activity. Wavelet and cross-wavelet techniques revealed that the periods found are intermittent, possibly because solar activity signals observed in tree rings are mostly due to solar influence on local climate (rainfall, temperature, and cloud cover) where trees grow up. Further, cross-wavelet analysis between sunspot and tree ring time series showed that the cross power around the 11 yr solar cycle is more significant during periods of high solar activity (grand maximum) than during periods of low solar activity (grand minimum). As Glaciar Pio XI is practically at the Pacific Ocean level, the tree-ring response may be stronger due to the heating of the Pacific Ocean water following an increase of the solar radiation incidence rather than at the higher altitudes of Osorno region.     

Water mass variation in the Mediterranean and Black Seas

The mass-induced sea level variability and the net mass transport between Mediterranean Sea and Black Sea are derived for the interval between August 2002 and July 2008 from satellite-based observations and from model data. We construct in each basin two time series representing the basin mean mass signal in terms of equivalent water height. The first series is obtained from steric-corrected altimetry while the other is deduced from GRACE data corrected for the contamination by continental hydrology. The series show a good agreement in terms of annual and inter-annual signals, which is in line with earlier works, although different model corrections influence the consistency in terms of seasonal signal and trend.In the Mediterranean Sea, we obtain the best agreement using a steric correction from the regional oceanographic model MFSTEP and a continental hydrological leakage correction derived from the global continental hydrological model WaterGAP2. The inter-annual time series show a correlation of 0.85 and a root mean square (RMS) difference of 15 mm. The two estimates have similar accuracy and their annual amplitude and phase agree within 3 mm and 23 days respectively. The GRACE-derived mass-induced sea level variability yields an annual amplitude of 27 ± 5 mm peaking in December and a trend of 5.3 ± 1.9 mm/yr, which deviates within 3 mm/yr from the altimetry-derived estimate.In the Black Sea, the series are less consistent, with lower accuracy of the GRACE-derived estimate, but still show a promising agreement considering the smaller size of the basin. The best agreement is realized choosing the corrections from WaterGAP2 and from the regional oceanographic model NEMO. The inter-annual time series have a correlation and RMS differences of 0.68 and 55 mm, their annual amplitude and phase agree within 4 mm and 6 days respectively. The GRACE-derived seawater mass signal has an annual amplitude of 32 ± 4 mm peaking in April. On inter-annual time scales, the mass-induced sea level variability is stronger than in the Mediterranean Sea, with an increase from 2003 to 2005 followed by a decrease from 2006 to 2008.Based on mass conservation, the mass-induced sea level variations, river runoff and precipitation minus evaporation are combined to derive the strait flows between the basins and with the Atlantic Ocean. At the Gibraltar strait, the net inflow varies annually with an amplitude of 52 ± 10 × 10⁻³ Sv peaking end of September (1 Sv = 10⁶ m³ s⁻¹). The inflow through the Bosphorus strait displays an annual amplitude of 13 ± 3 ×10⁻³ Sv peaking in the middle of March. Additionally, an increase of the Gibraltar net inflow (3.4 ± 0.8 × 10⁻³ Sv/yr) is detected.     

Global-scale validation of model-based load deformation of the Earth's crust from continental watermass and atmospheric pressure variations using GPS

Temporal mass variations in the continental hydrosphere and in the atmosphere lead to changes in the gravitational potential field that are associated with load-induced deformation of the Earth’s crust. Therefore, models that compute continental water storage and atmospheric pressure can be validated by measured load deformation time series. In this study, water mass variations as computed by the WaterGAP Global Hydrology Model (WGHM) and surface pressure as provided by the reanalysis product of the National Centers for Environmental Prediction describe the hydrological and atmospheric pressure loading, respectively. GPS observations from 14 years at 208 stations world-wide were reprocessed to estimate admittance factors for the associated load deformation time series in order to determine how well the model-based deformation fits to real data. We found that such site-specific scaling factors can be identified separately for water mass and air pressure loading. Regarding water storage variation as computed by WGHM, weighted global mean admittances are 0.74 ± 0.09, 0.66 ± 0.10, 0.90 ± 0.06 for the north, east and vertical component, respectively. For the dominant vertical component, there is a rather good fit to the observed displacements, and, averaged over all sites, WGHM is found to slightly overestimate temporal variations of water storage. For Europe and North America, with a dense GPS network, site-specific admittances show a good spatial coherence. Regarding regional over- or underestimation of WGHM water storage variations, they agree well with GRACE gravity field data. Globally averaged admittance estimates of pre-computed atmospheric loading displacements provided by the Goddard Geodetic VLBI Group were determined to be 0.88 ± 0.04, 0.97 ± 0.08, 1.13 ± 0.01 for the north, east and vertical, respectively. Here, a relatively large discrepancy for the dominant vertical component indicates an underestimation of corresponding loading predictions.