两种水体吸收系数测量方法的比较研究

基于2011年7月藻类培养实验期间的实测数据,对高光谱吸收衰减系数测量仪(AC-S)和紫外-可见分光光度计(UV2550)获取的水体吸收系数进行了比较分析.结果表明,短波波段AC-S测得吸收光谱曲线普遍低于UV2550测量结果,而长波波段恰恰相反;两种方法测量结果的相对误差基本可控制在±40％范围内;特征波段处,两种方法测量结果线性拟合的相关性较高,均可这98％以上,412 nm、440 nm、443nm波段斜率小于1,而488 nm、531nm、551 nm、667nm、675nm、678 nm波段斜率大于1.     

硬X射线相位光栅的设计与研制

针对在普通实验室和医院实现40—100 keV X射线相衬成像的需求,考虑到成像系统参数、X射线源空间相干特性及光栅衍射效率,设计出硅基相位光栅结构参数.利用我们已发展的光助电化学刻蚀技术研制出直径为5英寸的相位光栅,其空间周期为5.6 μm,线宽为2.8 μm,深度为40—70 μm.在理论分析的基础上,通过提高硅片两端有效工作电压和修正Lehmann电流密度公式,解决了实际刻蚀过程中出现的钻蚀问题.由实验结果可知,本方案对制作大面积高精度相位光栅十分有效.     

不同光强下小球藻纵向沉降及悬浮特性研究

通过用自制沉降柱研究小球藻(Chlorella vulgaris)在表层不同光强作用下纵向沉降特性以及分布规律, 为进一步了解水库中小球藻的纵向分布提供参考。实验室培养的小球藻按其直径可分为小于4.5 μm、4.5～5.5 μm、大于5.5 μm 3 个等级, 不同粒径的小球藻在不同光强的作用下沉速不同; 实验条件下小球藻的沉速分布在0.1～468.2 μm/s, 均值为32.8 μm/s; 小球藻的沉降速度随沉降柱表层光强增强而降低, 无光状态下时沉速是表层光强为10 000 lx 的2～3 倍; 小球藻直径大小与沉速呈正相关, 直径4.5～5.5 μm 的小球藻沉速是3.5～4.5 μm 的5~6 倍; 沉降稳定后实验柱中小球藻从表层至底层粒径逐渐变大, 除底层外小球藻在纵向峰值随光强增加而向下延伸, 如实验柱表层光强为1 000 lx 和4 000 lx时小球藻峰值出现实验柱表层, 而表层光强为7 000 lx 和10 000 lx 的实验峰值分别出现在水下300 mm和600 mm 处。     

卫星高度计及其应用

传统的遥感技术,都是利用地物的电磁波谱特征来提取物质的分类、数最或状态信息。由于海水的导电性,电磁波在海水中被强烈吸收,除了极狭窄的可见波段能透入表面几米至几十米外,其余的红外、微波段电磁波只能透入极表层、μm—mm深度。同时,由于海洋表层     

第一章 遥感图象信息提取和遥感地质工作程序

一、遥感图象地物信息的提取 地球表面物体对外来的电磁波都有反射、吸收和透射的作用。反射、吸收、透射电磁波能量占入射电磁波能量的百分比,即分别为反射率、吸收率和透射率,它们的差异可作为探测和区别地面目标物的有用信息。另外,不同的地物发射电磁波的能力也各不相同,当地物的温度高于绝对零度时,它就会向外发射电磁波(热辐射)。专题绘图仪的TM—6波段为10.40～12.50μm,属于远红外波段,若以远红外波段扫描成像而获得的遥感信     

海面溢油无人机高光谱遥感检测与厚度估算方法

海上溢油是海洋国家所面临的共同问题,但至今仍没有一种可靠实用的海上溢油准确识别和油量遥感监测方法。为此,本文以无人机高光谱遥感为手段,开展了海面溢油检测与厚度估算方法研究。实验中,通过搭建室外大型水槽溢油实验装置,获取了模拟真实海洋环境条件下不同溢油量的遥感和现场光谱数据,在此基础上,分析并提取了海上溢油特征光谱波段,给出了海上溢油高光谱检测模型;针对现场实验条件下水面油膜厚度难以测定的问题,设计了3种利用总体溢油量的油膜厚度估算模型。得到如下主要结论:（1）675 nm和699 nm是海上溢油检测的有效特征波段,但对极薄的油膜没有检测能力;（2）提出了归一化溢油指数模型、反比例模型和吸收基线模型等3种海上溢油油膜厚度估算模型,其中对于薄油膜（厚度≤ 5 μm）和厚油膜（厚度>50 μm）,反比例模型是溢油厚度反演的首选也是唯一选择。对于中厚度油膜,晴朗天气条件下,归一化溢油指数模型是油膜厚度反演的首选,同时反比例模型和溢油吸收基线模型也都有较好的反演能力,而在多云天气条件下,反比例模型效果最佳。     

东海海域典型赤潮水体反射光谱模拟研究

东海原甲藻(Prorocentrum donghaiense Lu)是我国东海海域的典型赤潮藻种,其在水体中通常呈垂直非均匀分布,并存在季节性和日内的垂直迁移现象。本文通过量化垂直迁移过程中东海原甲藻的分布状态,利用Hydrolight软件数值模拟各状态下的水体反射光谱,研究其光谱特征和变化规律。利用叶绿素浓度高斯垂向模型表征东海原甲藻在水体中的垂直分布,结合东海近岸海域二类水体的生物光学模型,模拟得到垂直迁移过程中东海原甲藻赤潮水体的反射光谱。对比分析叶绿素浓度垂向分布参数(背景叶绿素浓度、甲藻主体水层厚度、水体总生物量和叶绿素浓度峰值深度)对水体反射光谱的影响。研究结果表明,在东海原甲藻从次表层向表层垂直向上迁移过程中,水体反射光谱数值在蓝绿波段(400—570nm)减小,在黄红波段(570—720nm)增大,特别是在叶绿素荧光效应波段(680nm)处的变化尤为明显。     

皱纹盘鲍杂交幼鲍闽东内湾度夏初探

为探讨皱纹盘鲍杂交鲍幼鲍在闽东内湾度夏的生长与存活,以山东荣成两家育苗场培育的皱纹盘鲍Haliotis discus hannai杂交鲍幼鲍(XXK、DY)、福建东山岛培育的盘鲍H.discus discus幼鲍(DS)为材料,分别运输至福建霞浦内湾长腰海区、山东荣成爱连湾进行度夏培育.各幼鲍组XXK、DY、DS均为1龄苗种,起始壳长分别为31.51 mm±2.66 mm、30.76 mm±3.30 mm、30.63 mm±2.57 mm,且无显著性差异(P<0.05).经过6个月的培育,在南方闽东内湾培育条件下,皱纹盘鲍杂交鲍幼鲍组壳长的日增长率达95.34 μm/d±29.14μm/73.81 μm/d±29.37 μm/d,存活率为50.06%±0.25%、49.88%±0.17%;盘鲍组壳长的日增长率则为65.81 μm/d±29.71μm/d,存活率为28.81%±4.87%.作为对照,在北方培育条件下,皱纹盘鲍杂交鲍幼鲍组壳长的日增长率达67.85μm/d±29.01μm/d、63.749 μm/d±22.99 μm/d,存活率为78.90%±2.24%、86.56%±2.98%;盘鲍组壳长的日增长率则为27.87μm/d±29.21μm/d,存活率为43.19%±1.85%.双因素方差分析结果表明养殖环境与幼鲍来源,以及两者的交互作用均显著影响幼鲍度夏的生长发育.本研究结果对皱纹盘鲍杂交幼鲍在南方闽东内湾的养成提供了一定的参考.     

高光谱特征波段在海洋典型溢油油种识别中的精度评估

溢油种类精准识别对快速有效地治理污染具有重要的意义,高光谱遥感在海面溢油油种识别中至关重要.为探讨海洋典型溢油油种识别的高光谱特征波段范围,通过设计室外模拟溢油实验,在获取原油、燃料油、柴油、汽油和棕榈油等5种油种的实测高光谱数据基础上,运用因子分析和光谱标准偏差分析法遴选溢油油种的光谱特征波段,并利用支持向量机模型开...     

珠江磨刀门河口表层沉积物磁性特征及其动力沉积环境意义

基于2015年3月珠江磨刀门河口表层沉积物磁学和粒度测量结果,研究磨刀门河口磁性特征空间分布规律,分析磁性参数与沉积物粒度的关系,并探讨其对沉积动力环境的响应。磁性参数磁化率（χ）和饱和等温剩磁（SIRM）均在拦门沙处出现低值区,并在10 m等深线外呈现向海递减趋势;频率磁化率（χ_fd%）、非磁滞剩磁磁化率（χ_ARM）以及比值参数χ_ARM/SIRM和χ_ARM/χ在拦门沙处出现低值区,而在拦门沙外呈现高值:表明研究区域磁性特征由亚铁磁性矿物主导,而拦门沙区域存在一定量的不完全反铁磁性矿物。粒度是影响沉积物磁性特征的重要因素,SIRM/χ等参数与粗颗粒组分（大于63 μm）呈显著正相关,χ_fd%等参数与小于16 μm粒级组分高度相关,结果显示χ_fd%、χ_ARM、χ_ARM/SIRM以及χ_ARM/χ等参数可作为本区域沉积物细颗粒组分（小于16 μm）的代用指标,而SIRM/χ则可作为粗颗粒组分（大于63 μm）的代用指标。基于沉积物类型、动力环境等综合考虑,选取SIRM、S_-300、SIRM/χ参数聚类分析,可将磨刀门河口动力沉积环境分为4个区,结果与该区域动力环境及动力地貌格局具有一致性。本研究不仅对了解新动力格局下磨刀门河口演变模式具有重要意义,还可以丰富河口沉积动力学研究方法。     

Microbial Biomass and Organic Nutrients in the Deep-Sea Sediments of the Central Indian Ocean Basin

In order to assess the impact of deep-sea mining on the in situ benthic life, we measured the microbial standing stock and concentration of organic nutrients in the deep-sea sediments of the Central Indian Ocean Basin in the Indian pioneer area. Sediments were collected using box core and grab samples during September 1996. The total bacterial numbers ranged from 10 10 -10 11 cells per g -1 dry weight sediment. There was a marginal decrease in the number of bacteria from surface to 30 cm depth, though the subsurface section registered a higher number than did the surface. The highest numbers were encountered at depths of 4-8 cm. The retrievable number of bacteria were two orders less in comparison with the direct total counts of bacteria. An almost homogeneous distribution of bacteria, total organic carbon, living biomass, and lipids throughout the depth of cores indicates active microbial and benthic processes in the deep sea sediments. On the other hand, a uniform distribution of total counts of bacteria, carbohydrates, and total organic carbon in all the cores indicates their stable nature and suggests that they can serve as useful parameters for long-term monitoring of the area after the benthic disturbance. Further studies on temporal variability in this region would not only verify the observed norms of distribution of these variables but would also help to understand restabilization processes after the simulated benthic disturbance.     

海上大直径钢管桩打桩过程中桩周土强度弱化研究

海上大直径钢管桩打桩过程中,桩周土体受到强烈扰动而发生强度弱化,掌握桩周土体强度弱化规律对于准确预测打桩过程、保证工程安全具有重要意义。为研究土体强度弱化规律,开展了环剪试验模拟打桩对桩周土体的扰动,测试土体强度随剪切速率的变化规律,建立了描述土体强度弱化规律的拟合公式,引入到打桩分析软件中。研究结果表明：土体的强度折减程度不仅与土体本身的性质有关还受到土体的埋深和剪切速率的影响,埋深越深土体强度折减程度越低,剪切速率越高土体强度折减越高,在打桩分析中可采用这里推荐的线性折减方法来模拟不同深度处土体强度的折减规律。     

Geoacoustic Inversion via Genetic Algorithm and Its Application to Manganese Sediment Identification

An acoustic inversion method using a wide-band signal and two near field receivers is proposed and applied to multiple layered seabed models including a manganese sediment. The inversion problem can be formulated into a probabilistic model comprised of signals, a forward model, and additive noise. The forward model simulates wide-band signals, such as chirp signals, and is chosen to be the source-waveletconvolution plane wave modeling method. The wavelet matching technique, using weighted least-squares fitting, estimates the sediment sound-speed and thickness on which determination of the possible numerical ranges for a priori uniform distribution is based. The genetic algorithm is applied to a global optimization problem to find a maximum a posteriori solution for determined a priori search space. Here the object function is defined by an L 2 norm of the difference between measured and modeled signals. Not only the marginal pdf but also its statistics are calculated by numerical evaluation of integrals using the samples selected during importance sampling process of the genetic algorithm.     

A Review of Some Environmental Issues Affecting Marine Mining

This article reviews information recently available from existing marine and coastal mining for responses to environmental issues affecting marine mining at different depths. It is particularly but not exclusively concerned with those issues affecting seabed biodiversity impact and recovery. Much information has been gathered in the past 10 years from shallow mining operations for construction aggregate, diamonds, and gold, from coastal mines discharging tailings to shallow and deep water, and from experimental deep mining tests. The responses to issues identified are summarized in a series of eight tables intended to facilitate site-specific consideration. Since impacts can spread widely in the surface mixing layer SML, and can affect the biologically productive euphotic zone, the main issues considered arise from the depth of mining relative to the SML of the sea. Where mining is below the SML, the issue is whether it is environmentally better to bring the extraction products to the surface vessel for processing (and waste discharge), or to process the extraction products as much as possible on the seabed. Responses to the issues need to be sitespecific, and dependent on adequate preoperational environmental impact and recovery prediction. For deep tailings disposal from a surface vessel, there are four important environmental unknowns: (1) the possible growth of "marine snow" (bacterial flocs) utilizing the enormous quantities of fine tailings particles (hundreds or thousands of metric tons per day) as nuclei for growth, (2) the possibility that local keystone plankton and nekton species may migrate diurnally down to and beyond the depth of deep discharge and hence be subjected to tailings impact at depth, (3) the burrow-up capability of deep benthos and their ability to survive high rates of tailings deposition, and (4) the pattern and rate of dispersion of a tailings density current through the deep water column from discharge point to seabed. Actions to obtain relevant information in general and site-specifically are suggested.     

Increased Particle Fluxes at the INDEX Site Attributable to Simulated Benthic Disturbance

Particle fluxes were measured 7 m above the sea bottom during the predisturbance, disturbance, and postdisturbance periods by using time series sediment traps attached to seven deep-sea moorings deployed in the INDEX experiment site in the Central Indian Basin. The predisturbance particle fluxes varied between 22.3 to 55.1 mg m -2 day -1 . Increased and variable particle fluxes were recorded by the sediment traps during the disturbance period. The increase observed was 0.5 to 4 times more than the background predisturbance fluxes. The increases in particle fluxes (~4 times) recorded by the sediment trap located in the southwestern direction (DMS-1) were the greatest, which could be the result of preferential movement of resuspended particles generated during the deep-sea benthic disturbance along the general current direction prevailing in this area during the experimental period. Also, the traps located closer to the disturbance area recorded greater fluxes than did the traps far away, across the Deep Sea Sediment Resuspension System path. This variability in recorded particle fluxes by the traps around the disturbance area clearly indicates that physical characteristics such as grain size and density of the resuspended particles produced during the disturbance had an important effect on particle movement. The postdisturbance measurements during ~5 days showed a reduction in particle fluxes of ~50%, indicating rapid particle settlement.     

Determination of In Situ Sediment Shear Strength from Advanced Piston Corer Pullout Forces

The advanced piston corer (APC) has been used by the Ocean Drilling Program since 1985 for recovering soft sediments from the ocean floor. The pullout force measured on extracting the core barrel from the sediment is shown to correlate with the average shear strength of the sediment core measured in the ship's laboratory. A simple rule of thumb is derived relating the shear strength of the sediment to the pullout force. Multiple APC holes at individual sites allow the consistency of the pullout measurements to be assessed. The effects of different operational procedures during APC coring are also explored. Although generally applicable, the correlation between pullout force and laboratory measurements of shear strength breaks down for some APC holes, possibly because of the disturbance of some sediment types during the APC coring process. A better understanding of the physical process of APC coring, and its effect on the properties of the sediment both inside and immediately outside the core barrel, would indicate what confidence can be put on the measurement of pullout force as a way of evaluating the in situ shear strength of deep sea sediments.     

Phylogenetic diversity and phenotypic characterization of cultivable bacterioplankton isolated from polar oceans

A set of 27 marine planktonic bacteria isolated from the polar regions was characterized by 16S rDNA sequencing and physiological and biochemical testing. More than half of these bacteria were positive for caseinase, gelatinase and 13-glucosidase, and could utilize glucose, maltose or malic acid as carbon source for cell growth. Twelve isolates expressed nitrate reduction activities. Except for one antarctic isolate BSwlO175 belonging to Actinobacteria phylum, these isolates were classified as γ-Proteobacteria, suggesting that γ-Proteobacteria dominated in cultivable marine bacterioplankton at both poles. Genus Pseudoalteromonas was the predominant group in the Chukchi Sea and the Bering Sea, and genus ShewaneUa dominated in cultivable bacterioplankton in the Prydz Bay. With sequence similarities above 97%, genus Psychrobacter was found at both poles. These 27 isolates were psychrotolerant, and significant 16S rDNA sequence similarities were found not only between arctic and antarctic marine bacteria （ 〉 99% ）, but also between polar marine bacteria and bacteria from other aquatic environments （ ≥ 98.8% ）, including temperate ocean, deep sea, pond and lake, suggesting that in the polar oceans less temperature-sensitive bacteria may be cosmopolitan and have a bipolar, even global, distribution at the species level.     

Deep-Sea Sediment Compression Curves: Some Controlling Factors, Spurious Overconsolidation, Predictions, and Geophysical Reproduction

Oedometer tests have been carried out on 70 undisturbed surficial clays (at approximately 250 mm below the mudline), mostly collected by free-fall corers from sites widely scattered throughout the deep-sea North Atlantic. Acoustic measurements were also made, initially on contiguous samples and ultimately on the same sample using a geophysically instrumented oedometer which also collected electrical resistivity data. Apart from those quiescent areas below the carbonate compensation depth, such as north of the West Indies where very fine clays exist, most of the samples are silty clays whose geotechnical-geophysical properties are dependent on the type of clay minerals present (and their ability to take in moisture), the sand-size fraction, and the quantity of carbonate present. Thus the pure clays have high compressibilities which decrease on the addition of coarse particles, while the converse is true for the acoustic parameters, these increasing with the sand fraction. Using the notion of the intrinsic compression line for all samples, and comparison to it of the measured compression curves, it is clear that, contrary to some previously held ideas, most deep-sea clays are normally consolidated; the addition of carbonate has the effect of creating an open, stronger sediment skeleton. Interestingly, where information is available, the variation with depth of a sample's acoustic velocity follows the void ratio pressure relationship of the compression curve. This allows the construction of an in-situ sediment compression curve using the in-situ geophysical observations.