Evaluation of shear strength of rock joints subjected to cyclic loading

Variation of the shear strength of rock joints due to cyclic loadings is studied in the present paper. Identical joint surfaces were prepared using a developed moulding method with special mortar and shear tests were performed on these samples under both static and cyclic loading conditions. Different levels of shear displacement were applied on the samples to study joint behaviour before and during considerable relative shear displacement. It was found that the shear strength of joints is related to rate of displacement (shearing velocity), number of loading cycles and stress amplitude. Finally, based on the experimental results, mathematical models were developed for evaluation of shear strength in cyclic loading conditions.     

Earthquake-induced residual deformation of Ariake clay deposits with leaching

It is widely known that the sensitivity ratio of Ariake marine clay increases, if the clay is leached. Therefore, it is assumed that the mechanical properties of such clay considerably change and the shear strength decreases, if it is subjected to a cyclic load as a disturbance force, like earthquakes. In the present study, dynamic deformation and strength tests, as well as consolidation tests were conducted on Ariake clay that had leached. Static shear tests were also carried out on the clay after it had been subjected to a cyclic load. The stability of man-made earth structures on Ariake clay deposits that had leached during earthquakes was investigated. Undisturbed samples of the clay sedimented in the sea area were used in all the tests. Furthermore, an earthquake-induced residual deformation analysis was also conducted on the basis of the test results described above. Consequently, the following behaviors were observed in the study. (1) When Ariake marine clay was leached, the dynamic strength decreased and the shear modulus after subjecting it to a cyclic load remarkably decreased. (2) The effect of the leaching on the behavior of Ariake clay deposits was considerable during earthquakes.     

不同应力分量耦合模式下天津滨海饱和黏性土变形特性研究

地基土单元体在地震荷载作用下将产生主应力轴连续旋转,不同的应力耦合模式对土的强度、孔压以及变形等特性影响显著。利用GCTS空心圆柱扭剪仪,对天津滨海软土场地饱和黏性土进行K0固结下的不同应力耦合模式的循环剪切试验。着重对比相同应力路径下竖向和扭剪双向耦合加载模式,内外围压和扭剪的三向耦合加载模式以内外围压、竖向和扭剪的四向耦合加载模式条件下饱和黏性土的变形特性、循环软化特性。试验结果表明:在相同的动强度下,四向耦合应力模式更容易破坏且变形特性以及软化特性较双向、三向耦合下发展更加迅速;剪应力分量对试样软化变形特性的影响更加显著。     

Cyclic testing of moment-shear force interaction in reinforced concrete shear wall substructures

Previous quasi-static cyclic tests of shear walls, which routinely used an incremental lateral displacement test protocol with a constant axial load, failed to reflect the character of moment-shear force interaction of prototype buildings. To study the effect of the moment-shear force interaction on the seismic performance of shear walls, three identical 2-story shear wall specimens with different loading patterns were constructed at 1/2 scale, to represent the lower portion of an 11-story high-rise building, and were tested under reversed cyclic loads. The axial force, shear force and bending moment were simultaneously applied to simulate the effects of gravity loads and earthquake excitations on the prototype. The axial force and bending moment delivered from the upper structure were applied to the top of the specimens by two vertical actuators, and the shear force was applied to the specimens by two horizontal actuators. A mixed force-displacement control test program was adopted to ensure that the bending moment and the lateral shear were increased proportionally. The experimental results show that the moment-shear force interaction had a significant effect on the failure pattern, hysteretic characteristics, ductility and energy dissipation of the specimens. It is recommended that moment-shear force interaction should be considered in the loading condition of RC shear wall substructures cyclic tests.     

Nonlinear elastic behavior of fiber-reinforced soil under cyclic loading

Experimental investigations and modeling of nonlinear elasticity of fiber-reinforced soil under cyclic loading at small strain are conducted in this paper. The investigations include three aspects. First, cyclic shear tests are conducted using conventional triaxial apparatus. Twenty-seven specimens with three different fiber contents are employed to conduct triaxial cyclic shear tests under different confining pressure and loading repetition. Effects of geofiber, confining pressure and loading repetition on elastic shear modulus of reinforced soil are studied and analyzed. Second, a hyperbolic function is introduced to describe the nonlinear stress–strain skeletal curve under cyclic loading. Nonlinear elastic modulus is expressed as a function of shear strain and two variables A and B that are related to the initial tangential modulus and ultimate cyclic loading stress, respectively. In the present paper, variables A and B both are further assumed to be functions of geofiber content, confining pressure and loading repetition. Finally, eight constitutive coefficients of the nonlinear elastic model are calibrated using stress–strain curves from cyclic triaxial shear tests. The calibration of parameters is conducted using the technique of the linear regression for multiple variables. Impacts and effects of geofiber, confining pressure and loading repetitions on soil nonlinear elastic behavior are discussed.     

Cyclic shearing and liquefaction of soil under irregular loading: an incremental model for the dynamic earthquake-induced deformation

The paper presents a mathematical model for the deformation of soil under irregular cyclic loading in the simple-shear conditions. The model includes the possible change in the effective pressure in saturated soil due to the cyclic shearing, the reciprocal influence of the effective pressure on the response of the soil to the shear loading, and the pore pressure dissipation due to the seepage of the pore fluid. The hysteresis curves for the strain–stress relationship are constructed in such a way that they produce both the required backbone curve and the required damping ratio as functions of the strain amplitude. At the same time, the approach enables the constitutive functions involved in the model to be specified in various ways depending on the soil under study. The constitutive functions can be calibrated independently of each other from the conventional cyclic shear tests. The constitutive model is incorporated in the boundary value problem for the dynamic site response analysis of level ground. A numerical solution is presented for the dynamic deformation and liquefaction of soil at the Port Island site during the 1995 Hyogoken-Nambu earthquake.     

Cyclic strength and deformation of crushable carbonate sand

Cyclic triaxial tests have been carried out on a skeletal carbonate sand from the west coast of Eire. Results are presented for undrained cyclic shear tests on samples with 80% of relative density consolidated under both isotropic and anisotropic conditions. Failure was defined as a 5% double amplitude cyclic strain and a 5% peak axial strain for stress-reversal and non-reversal stress conditions, respectively. Using this definition the cyclic strength for isotropically consolidated samples was affected by the confining pressure although the angular platey nature of the sand resulted in higher cyclic strengths than for a comparable silica sand. For anisotropically consolidated samples the cyclic strength increased with increasing initial static shear stress while on the other hand the cyclic strength normalised in the usual way with respect to the initial confining pressure decreased as this pressure increased.     

In-plane shear behaviour of unreinforced and jacketed brick masonry walls

This paper deals with the results of cyclic load tests on masonry walls performed for the purpose of evaluation of in-plane shear behaviour and identification of shear strength, stiffness and energy dissipation. Eight walls in two series were assembled in laboratory conditions. The first series consisted of four unreinforced masonry walls constructed from solid clay bricks and lime mortar. The walls from the second series were strengthened by application of RC jackets on both sides. These were constructed of the same material and were characterized by the same geometry properties and vertical load levels as those of the walls from the first series. The main goal of the tests was to compare the behaviour of the unreinforced and strengthened walls under cyclic horizontal load. The results from the tests showed that the application of the strengthening method contributed to a significant improvement of the shear resistance of the jacketed walls. Analytical models were used to predict the shear resistance of the walls. Good agreement with the experimental results was obtained with a model based on tensile strength of masonry.     

Settlements under consecutive series of cyclic loading

In this study, consolidation settlements of soft clay caused by cyclic loading and the affecting factors such as number of cycles and stress level were experimentally investigated. A group of samples prepared in slurry consolidometer in the laboratory were tested using cyclic simple shear testing device. Normally consolidated samples were subjected to five consecutive series of cyclic loading and drainage for 60 min were applied between each cyclic loading stages. Cyclic tests were performed with stress controlled two-way sinusoidal wave loading with different stress levels and number of cycles. Frequency of cyclic loading was constant as 0.1 Hz. As a result of this study, it can be concluded that soft clays subjected to undrained cyclic loading and drainage cycles exhibit more resistance against subsequent cyclic shear stresses. The consolidation settlements, pore pressures and shear strains decrease after each stage of cyclic loading.     

钢筋混凝土框架角节点抗剪强度试验研究

通过对6个钢筋混凝土框架梁柱角节点在低周反复荷载作用下的试验,调查了高强度节点箍筋、双向加载等对节点强度的影响。试验结果证明,节点强度试验值为规范设计值的85%左右,设计式应导入强度降低系数。高强度箍筋对节点强度提高影响很小,在节点强度设计时可忽略不计。双向加载的节点强度只有单向加载时的80%,节点抗震设计时角节点应作为所有边节点中最不利情况考虑。楼板虽然可以提高梁的强度及刚度,但对角节点强度及最大荷载后的节点延性有不利影响。     

Cyclic response of saturated silts

Softening and strength loss of sands with increasing excess pore water pressure under repeated loads is well-known. However, extensive damage to the built environment also occurs at the sites underlain by fine grained soils during seismic shaking. The primary objective of this study is to investigate the factors affecting cyclic behavior of saturated low-plastic silt through laboratory testing. For this purpose, an extensive laboratory testing program including conventional monotonic and cyclic triaxial tests was carried out over reconstituted silt samples. The effects of the inherent soil properties and the effects of loading characteristics on the cyclic response of saturated low-plastic reconstituted silt samples were examined separately. Based on the test results, a model was introduced to estimate the effect of initial shear stress on the cyclic response. Besides, liquefaction susceptibility of the samples was examined via current liquefaction susceptibility criteria.     

Overstrength of dowelled CLT connections under monotonic and cyclic loading

This paper presents an evaluation of overstrength based on an experimental study on dowelled connections in Cross Laminated Timber (CLT). Connection overstrength needs to be well understood in order to ensure that ductile system behaviour and energy dissipation can be achieved under seismic loading. Overstrength is defined as the difference between the code-based strength, using characteristic material strengths, and the 95th percentile of the true strength distribution. Many aspects contribute to total connection overstrength, which makes its definition challenging. In this study, half-hole embedment tests were performed on CLT to establish embedment strength properties and three point bending tests were performed to determine the fastener yield moment. Different connection layouts, making use of mild steel dowels and an internal steel plate, were tested under monotonic and cyclic loading to evaluate theoretically determined overstrength values and study the influence of cyclic loading on overstrength. Experimental results were compared with strength predictions from code provisions and analytical models for ductile response under monotonic loading. It was found that cyclic loading does not significantly influence overstrength for connections that respond in a mixed-mode ductile way indicating that in future more expedient monotonic test campaigns could be used. This work also provides further experimental data and theoretical considerations necessary for the estimation of a generally applicable overstrength factor for dowelled CLT connections.     

饱和南京细砂孔压增量模型的普适性研究

循环荷载作用下饱和砂土的孔压增长规律是土动力学的核心内容之一。基于笔者在给定相对密度、均等固结条件下饱和南京细砂的不排水等幅循环三轴试验结果建立的孔压增量模型,进一步进行了不同相对密度、不同固结比条件下饱和南京细砂的不排水等幅循环三轴试验,将上述均等固结的孔压增量模型拓展为适用于不同相对密度、均等和非均等固结条件的孔压增量模型。采用拓展后的孔压增量模型对试验结果进行分析的结果表明：通过该孔压增量模型预测验证试验的孔压与验证试验测试的孔压具有较好的一致性,说明该孔压增量模型具有普适性。     

钢筋混凝土核心筒体抗震性能试验研究

本文对两组五个钢筋混凝土核心筒试件进行了低周反复荷载试验，研究了不同轴压比和剪跨比的核心筒破坏机理、承载能力、延性和耗能能力等方面的抗震性能。结果表明，轴压比对核心筒的抗震性能有较大影响。     

CFRP布约束增强高强混凝土柱抗震性能数值分析

采用地震工程开源模拟软件OpenSees（Open System for Earthquake Engineering Simulation）对CFRP（Carbon Fiber Reinforced Polymer,碳纤维增强复合材料）布加固高强钢筋混凝土方柱的抗震性能进行了数值分析。采用Steel02Material和Concrete02Material材料本构模型模拟了CFRP布加固高强混凝土方柱的抗震性能;在此基础上,进一步研究了轴压比和剪跨比这2个因素对试件抗震性能的影响。将所得数值分析结果与相同条件下的试验结果对比后发现：基于Steel02 Material和Concrete02 Material材料本构,利用OpenSees,可以较好地模拟CFRP布加固高强混凝土方柱的抗震性能,并且与试验结果（滞回曲线、骨架曲线、水平承载力和位移延性系数）能够较好地吻合,从而说明该数值分析方法还可以准确地反映出轴压比和剪跨比对高强混凝土柱抗震性能的影响规律。     

型钢高强混凝土柱轴压比限值的试验研究

通过20个型钢高强混凝土柱的低周反复加载试验对其受力性能进行了研究，分析了剪跨比、轴压比、配箍率以及混凝土强度对型钢高强混凝土柱延性的影响，提出了不同剪跨比、不同配箍率的型钢高强混凝土柱的轴压比限值。其中，剪跨比大于2．0的型钢高强混凝土柱的轴压比限值由大、小偏心界限破坏时力的平衡条件并结合试验结果确定，而剪跨比小于2．0的型钢高强混凝土柱的轴压比限值则通过与剪跨比大于2．0的型钢高强混凝土柱的延性对比加以确定。     

Pre-shear effect on liquefaction resistance of a Fujian sand

Pre-shear history has been shown to be a critical factor in the liquefaction resistance of sand. By contrast to prior experimental studies in which triaxial shear tests were used to examine the effects of pre-shear on the liquefaction resistance of sand, hollow cylinder torsional shear tests were used in this study to avoid the influence of the inherent anisotropy that is inevitably produced during the sample preparation process because of gravitational deposition. A series of cyclic undrained shear tests were performed on sand samples that had experienced medium to large pre-shear loading. The test results showed that the liquefaction resistance of sand can be greatly reduced by its pre-shear history, and a pre-shear strain within the range from 0.1% to 5% can cause sand to be more prone to liquefaction. During the cyclic shear tests, the samples that had experienced pre-shear loading exhibited different behaviors when cyclic shear loading started in different directions, i.e., the clockwise direction and the counterclockwise direction. If the cyclic loading started in the identical direction as the pre-shear loading, then the mean effective stress of the sand was almost unchanged during the first half of the loading cycle; if the cyclic loading started in the direction opposite to that of the pre-shear loading, then the mean effective stress decreased significantly during the first half of the loading cycle. However, this anisotropic behavior was only remarkable during the first loading cycle. From the second cycle onward, the speeds of the decrease in the mean effective stresses in the two types of shear tests became similar.     

地震波类型对砂土震陷影响的数值模拟分析

地震波是一种随机的、不规则作用的动荷载脉冲,可分为振动型和冲击型。不同类型的地震波会对砂土液化和变形等产生重要影响,而传统的砂土震陷计算方法往往忽视这种因素,只考虑最大加速度幅值。通过编写UMAT子程序,在非线性有限元软件ABAQUS中开发亚塑性砂土边界面模型,对不同地震波类型下不同相对密度的砂土进行动单剪试验模拟,得到一系列砂土剪应变及竖向应变的时程曲线,并与室内试验结果进行对比分析。研究表明:在同一工况下,同类型的地震波引起的砂土竖向应变相近,不同类型引起的竖向应变差异明显;振动型地震波比冲击型引起的竖向应变更大。     

型钢混凝土梁柱框支剪力墙结构抗震性能试验研究

框支剪力墙结构在实际工程中经常被采用,震害表明钢筋混凝土框支剪力墙结构抗震性能较差,本文提出型钢混凝土梁柱框支剪力墙结构对此加以改进。作者进行了4个1/4缩尺模型在竖向荷载和单调及低周反复水平荷载作用下的对比试验,其中3个试件采用型钢混凝土转换梁、型钢混凝土框支柱,1个试件采用钢筋混凝土转换梁、钢筋混凝土框支柱。我们分析其承载力、刚度、变形、延性和破坏形态等。试验结果表明,型钢混凝土梁柱框支剪力墙结构承载力高、延性好、滞回曲线丰满,变形能力和耗能能力较强。     

Experimental study of the seismic behavior of partially concrete‐filled steel bridge piers under bidirectional dynamic loading

The seismic behavior of steel bridge piers partially filled with concrete under actual earthquake conditions was investigated by using 20 square section specimens subjected to static cyclic loading tests and single‐directional and bidirectional hybrid loading tests. Acceleration records of two horizontal NS and EW directional components for hard (GT1), medium (GT2), and soft grounds (GT3), obtained during the 1995 Kobe earthquake, were adopted in dynamic tests. Experimental results clearly showed that maximum and residual displacements under actual earthquake conditions cannot be accurately estimated by conventional single‐directional loading tests, especially for GT2 and GT3. A modified admissible displacement was proposed on the basis of bidirectional loading test results. The concrete fill can effectively improve the seismic resistance performance if the concrete inside the steel bridge piers is sufficiently high in quantity. Copyright © 2013 John Wiley & Sons, Ltd.