Surface wave studies for shear wave velocity and bedrock depth estimation over basalts

Shear wave velocity (V _S) estimation is of paramount importance in earthquake hazard assessment and other geotechnical/geo engineering studies. In our study, the shear wave velocity was estimated from ground roll using multichannel analysis of surface wave (MASW) technique making use of dispersive characteristics of Rayleigh type surface waves followed by imaging the shallow subsurface basaltic layers in an earthquake-prone region near Jabalpur, India. The reliability of MASW depends on the accurate determination of phase velocities for horizontally traveling fundamental mode Rayleigh waves. Inversion of data from surface waves resulted in a shear wave velocity (V _S) in the range of 200–1,200 m/s covering the top soil to weathering and up to bedrock corresponding to a depth of 10–30 m. The P-wave velocity (V _P) obtained from refraction seismic studies at these locations found to be comparable with V _S at an assumed specific Poisson’s ratio. A pair of selected set of V _S profiles over basalt which did not result in a hazardous situation in an earthquake of moderate magnitude are presented here as a case study; in other words, the shear wave velocity range of more than 200 m/s indicate that the area is highly unlikely prone to liquefaction during a moderate or strong earthquake. The estimated depth to basalt is found to be 10–12 m in both the cases which is also supported by refraction studies.     

Estimation of shearwave velocity in drifts using multichannel analysis of surface wave (MASW) technique — A case study from Jammu & Kashmir,India

Multichannel analysis of surface waves (MASW) is a non-destructive seismic prospecting method utilizing Rayleigh waves for imaging and characterizing shallow sub-surface structure. Multichannel analysis of surface waves (MASW) studies were conducted in drift areas of two bridge sites in the hilly terrain of J&K for imaging and characterizing shallow sub-surface structure. The purpose of the present study is to estimate the shear wave velocity (V_S) and subsurface structure in four drifts made in a hilly terrain for construction of two bridges. Rayleigh waves are having dispersive properties, travelling along or near the ground surface and are usually characterized by relatively low velocity, low frequency, and high amplitude. The study area comprises of Tertiary group of rocks which are underlain by Siwalik group. The main rock type in the study area is dolomite which has undergone various geological processes like weathering, jointing, fracturing and shearing. MASW data was collected inside four drifts in the mountainous terrain of J&K state which are located on either sides of Chenab river. The data was analyzed by relevant processing software using dispersion and inversion technique. Shear wave velocities were estimated up to 30 m depth. Average shear wave velocity (V_S ³⁰) up to top 30m was also computed. It is observed that, V_S in the range 400–800 m/s upto 10–15 m corresponding to weathered rock, followed by compact dolomite rock up to the depth of about 30 m with V_S in the range 1200–1600 m/s. Some low velocity zones are also identified from these sections which represent shear zones.     

Determination of shear wave velocity and depth to basement using multichannel analysis of surface wave technique

The dispersive characteristics of Rayleigh type surface waves were utilized to estimate shear wave velocity (Vs) profile followed by imaging the shallow subsurface granitic layers in the heart of Hyderabad. The reliability of Multichannel Analysis of Surface Waves (MASW) depends on the accurate determination of phase velocities for horizontally traveling fundamental mode Rayleigh waves. Multichannel recording leads to effective identification and isolation of various factors of noise. Calculating the 1-D shear wave velocity (Vs) field from surface waves ensures high degree of accuracy irrespective of cultural noise. The main advantage of mapping the bed rock surface with shear wave velocity (Vs) is the insensitivity of MASW to velocity inversion besides being free from many constraints such as contrast in physical properties etc. Modeling of surface waves data results a shear wave velocity (Vs) of 250?C750 m/s covering the top soil to weathering and up to bedrock corresponding to a depth range of 10?C30 m. Further, the computed N values (which is an indicator of site characteristic) based on the harmonic shear wave velocity up to a depth of 5 m is found to be quite high (> 25?C30) well above 5 indicating the site to be safe and strong enough and not prone to liquefaction. A pair of selected set of results over granites are presented here as a case study highlighting the salient features of MASW.     

Multichannel analysis of surface waves (MASW) for seismic site characterization using 2D genetic algorithm at Bahrah area,Wadi Fatima,Saudi Arabia

The present study deals with the seismic site classification of Bahrah area, Wadi Fatima, to characterize the local site conditions. The dynamic behavior of sediments was studied by the application of surface wave inversion. The multichannel analysis of surface waves (MASW) shallow geophysical technique was utilized for site classification. MASW survey was carried out at 66 sites along with 13 seismic refraction profiles at suitable localities. MASW and seismic refraction profiles were processed and compared with the available borehole data. The integration of MASW techniques with seismic refraction and borehole data progressively enhanced the subsurface visualization and reliability of the shear wave velocity estimation in the subsurface in the study area. The subsurface shear-wave velocity model was achieved by the solution of an inverse problem-based dispersion of surface waves and propagation in a vertically heterogeneous medium. The 2D genetic algorithm was employed for the inversion of dispersion curves to obtain velocity and thickness of subsurface layers. The depth to engineering bedrock and velocity of shear waves in the first 30 m was deciphered and mapped. The depth of bedrock in study area varies from 4 to 30 m, and V _{S 30} ranges from 320 to 800 m/s. The most of study area falls in B and C class categories in addition to few sites of D class according to the NEHRP guidelines.     

Shear Wave Velocities in the Estimation of Earthquake Hazard Over Alluvium in Seismically Active Region

It is well known that the potential hazard during an earthquake is mainly in alluvium or alluvium filled basins; shear wave velocity plays a significant role in estimating the possible hazard during an earth quake in such an area. This paper presents shear wave velocity profile from Jabalpur, Central India mainly dominated by alluvial soil that was moderately affected by an earthquake of magnitude 6.5 in May, 1997. The acquired shear wave velocity by Multichannel Analysis of Surface Wave (MASW) in as many as 36 sites over alluvial soil ranges from 200 m/sec to 400 m/sec and in a few sites marginally less than 200 m/sec corresponding to a sub-surface depth of 30–35 m. Further, the computed N values vary as low as near zero to less than 25. The study is substantiated by the estimation of P-wave velocity by refraction seismic method at the same locations of MASW which ranges from 350 m/sec to 2200 m/sec. The results suggest that the damage during an earth quake appears to be highly unlikely in view of the marginally high Vs up to depth of 30 m. This study on seismic hazard is substantiated by the estimation of frequency of the ground as well as amplification which is found to be a maximum of about 2.5 in the frequency band of 2–6 Hz in west and north western portion of the study area.     

Applications of a GIS-based geotechnical tool to assess spatial earthquake hazards in an urban area

A geotechnical information system (GTIS) was constructed within a spatial geographic information system (GIS) framework to reliably predict geotechnical information and accurately estimate site effects at Gyeongju, an urban area in South Korea. The system was built based on both collected and performed site investigation data in addition to acquired geo-knowledge data. Seismic zoning maps were constructed using the site period (T _G) and mean shear wave velocity to a depth of 30 m (V _S30), and these maps were presented as a regional strategy to mitigate earthquake-induced risks in the study area. In particular, the T _G distribution map indicated the susceptibility to ground motion resonance in periods ranging from 0.2 to 0.5 s and the corresponding seismic vulnerability of buildings with two to five stories. Seismic zonation of site classification according to V _S30 values was also performed to determine the site amplification coefficients for seismic design and seismic performance evaluation at any site and administrative subunit in the study area. In addition, we investigated the site effects according to subsurface and surface ground irregularities at Gyeongju by seismic response analyses in time domains based on both two- and three-dimensional spatial finite element models, which were generated using spatial interface coordinates between geotechnical subsurface layers predicted by the GTIS. This practical study verified that spatial GIS-based geotechnical information can be a very useful resource in determining how to best mitigate seismic hazards, particularly in urban areas.     

Geospatial contour mapping of shear wave velocity for Mumbai city

Shear wave velocity is one of the most important input parameter in the analysis of geotechnical earthquake engineering problems, particularly to estimate site-specific amplification factor and ground response study. Dynamic in situ tests such as spectral analysis of surface waves (SASW) or multichannel analysis of surface waves (MASW) are very expensive. Also due to lack of specialized personnel, these tests are generally avoided in many soil investigation programs. Worldwide, several researchers have developed correlations between the SPT ‘N’ value and shear wave velocity ‘V _s’, which are useful for determining the dynamic soil properties. In the present study, more than 400 numbers of soil borehole data were collected from various geotechnical investigation agencies, government engineering institutes and geotechnical laboratories from different parts of Mumbai city, which is financial capital of India with highest population density. In this paper, an attempt has been made to develop the correlation between the SPT ‘N’ value and shear wave velocity ‘V _s’ for various soil profile of Mumbai city and compared with other existing correlations for different cities in India. Using Geographical Information System (GIS), a geospatial contour map of shear wave velocity profile for Mumbai city is prepared with contour intervals of 25 and 50 m/s. The scarcity of database or maps of shear wave velocity profile for Mumbai city will make the present geospatial contour maps extremely useful and beneficial to the designer, practitioners for seismic hazard study involved in geotechnical earthquake engineering.     

Delineation of shallow resistivity structure in the city of Burdur,SW Turkey by vertical electrical sounding measurements

The city of Burdur, which is built on an alluvium aquifer, is located in one of the most seismically active zones in southwestern Turkey. The soil properties in the study site are characterized by unconsolidated and water-saturated sediments including silty, clayey and sandy units, and shallow groundwater level is the other characteristic of the site. Thus, the city is under soil liquefaction risk during a large earthquake. A resistivity survey including 189 vertical electrical sounding (VES) measurements was carried out in 2000 as part of a multi-disciplinary project aiming to investigate settlement properties in Burdur city and its vicinity. In the present study, the VES data acquired by using a Schlumberger array were re-processed with 1D and 2D inversion techniques to determine liquefaction potential in the study site. The results of some 1D interpretations were compared to the data from several wells drilled during the project. Also, the groundwater level map that was previously obtained by hydrological studies was extended toward north by using the resistivity data. 2D least-squares inversions were performed along nine VES profiles. This provided very useful information on vertical and horizontal extends of geologic units and water content in the subsurface. The study area is characterized by low resistivity distribution (<150 Ωm) originating from high fluid content in the subsurface. Lower resistivity (3–30 Ωm) is associated with the Quaternary and the Tertiary lacustrine sediments while relatively high resistivity (40–150 Ωm) is related to the Quaternary alluvial cone deposits. This study has also shown that the resistivity measurements are useful in the estimation of liquefaction risk in a site by providing information on the groundwater level and the fluid content in the subsurface. Based on this, we obtained a liquefaction hazard map for the study area. The liquefaction potential was classified by considering the resistivity distributions from 2D inversion of the VES profiles, the types of the sediments and the extended groundwater level map. According to this map, the study area was characterized by high liquefaction hazard risk.     

GIS-based multi-criteria earthquake hazards evaluation using analytic hierarchy process for a nuclear power plant site,west Alexandria,Egypt

Nuclear power plants are designed to prevent the hazardous effects of the earthquakes and any external events to keep the safety of the plant. Ninety-one shallow seismic refraction profiles were performed to determine shear wave velocity of the engineering layers at the site of El Dabaa area that is situated to the northern coastline of Egypt for seismic hazard microzonation evaluation according to hazard index values. A microzonation is a procedure of delineating an area into individual zones having different ranks of numerous seismic hazards. This will aid in classifying areas of high seismic risk which is vigorous for industrial design of nuclear structures. The site response analysis requires the characterization of subsurface materials considering local subsurface profiles of the site. Site classification of the area under investigation was undertaken using P- and S-waves and available borehole data. The studied nuclear power plant site has been characterized as per NEHRP site classification using an average velocity of transverse wave (V _s ³⁰ ) of depth 30 m which acquired from seismic survey. This site was categorized into two site classes: the major one is “site class B,” and the minor one is “site class A.” The attenuation coefficient, the damping ratio and the liquefaction potential are geotechnical parameters which were derived from P- and S-waves, and have their major effects on the seismic hazard contribution. 1D ground response analysis was carried out in the places of seismic profiles inside the site for estimating the amount of ground quaking using peak ground acceleration (PGA), site amplification, predominant frequency and spectral accelerations on the surface of ground by the DEEPSOIL software package. Seven factors (criteria) deliberated to assess the earthquake hazard index map are: (1) the peak ground acceleration at the bedrock, (2) the amplification of the site, (3) the liquefaction potential, (4) the main frequency of the earthquake signal, (5) the average V _s of the first 30 m from the ground surface, (6) the depth to the groundwater and (7) the depth to the bedrock. These features were exemplified in normalized maps after uniting them to 0–1 scores according to some criteria by the minimum and maximum values as linear scaling points. Multi-criteria evaluation is an application of multi-criteria decision analysis theory that used for developing a seismic hazard index map for a nuclear power plant site at El Dabaa area in ArcGIS 10.1 software. Two models of decision making were used in this work for seismic hazard microzonation. The analytic hierarchy process model was applied to conduct the relative weights of the criteria by pairwise comparison using Expert Choice Software. An earthquake hazard index map was combined using Weighted Linear Combination model of the raster weighted overlay tool of ArcGIS 10.1. The results indicated that most of the study site of the nuclear power plant is a region of low to moderate hazard; its values are ranging between 0.2 and 0.4.     

Simultaneous inversion of the aftershock data of the 1993 Killari earthquake in Peninsular India and its seismotectonic implications

The aftershock sequence of the September 30th, 1993 Killari earthquake in the Latur district of Maharashtra state, India, recorded by 41 temporary seismograph stations are used for estimating 3-D velocity structure in the epicentral area. The local earthquake tomography (LET) method of Thurber (1983) is used. About 1500P and 1200S wave travel-times are inverted. TheP andS wave velocities as well asV _P/V_Sratio vary more rapidly in the vertical as well as in the horizontal directions in the source region compared to the adjacent areas. The main shock hypocentre is located at the junction of a high velocity and a low velocity zone, representing a fault zone at 6–7 km depth. The estimated average errors ofP velocity andV _P/V_Sratio are ±0.07 km/s and ±0.016, respectively. The best resolution ofP and S-wave velocities is obtained in the aftershock zone. The 3-D velocity structure and precise locations of the aftershocks suggest a ‘stationary concept’ of the Killari earthquake sequence.     

Geophysical investigation for shallow subsurface geotechnical problems of Mokattam area,Cairo, Egypt

Nine vertical electrical soundings of Schlumberger configuration were measured with AB/2 = 1–500 m. Manual and computerized interpretation were done to detect the subsurface stratigraphy of the study area. The results show that the subsurface section consists of alternated units of limestone, clay, marly limestone and dolomitic limestone and the thickness of clay unit ranged from 10 to 40 m. Nine dipole–dipole sections have also been constructed to give a clearer picture of the subsurface at the study area. The length of each dipole–dipole section is 235 m, with a electrode spacing ranging between 5 and 25 m. The Res2Dinv software was used for processing and interpretation of field data. The dipole–dipole sections at the upper plateau display high resistivity values at most parts of the plateau. Twelve shallow seismic refraction profiles are measured at selected locations for the dipole sections to define the interface between the fractured limestone and the upper surface of the clay layer. Each profile consists of 24 geophones with a geophone spacing of 2–3 m. Interpretation of seismic data indicates that the surface layer of the upper plateau consists of fractured limestone with a velocity range of 1.16–1.56 km/s and another layer of compacted clay with a velocity range of 1.38–1.88 km/s. Furthermore, the surface layer of the middle plateau consists of marl and marly limestone with a velocity about 2.1 km/s and its underlying layer consists of massive limestone with a velocity of 4.94 km/s.     

3-D velocity structure of the 2003 Bam earthquake area (SE Iran): Existence of a low-Poisson's ratio layer and its relation to heavy damage

To understand the generation mechanism of the Bam earthquake (Mw 6.6), we studied three-dimensional V_P, V_S and Poisson's ratio (σ) structures in the Bam area by using the seismic tomography method. We inverted accurate arrival times of 19490 P waves and 19015 S waves from 2396 aftershocks recorded by a temporal high-sensitivity seismic network. The 3-D velocity structure of the seismogenic region was well resolved to a depth of 14 km with significant velocity variations of up to 5%. The general pattern of aftershock distribution was relocated by using the 3-D structure to delineate a source fault for a length of approximately 20 km along a line 4.5 km west of the known geological Bam fault; this source fault dips steeply westward and strikes a nearly north–south line. The main shallow cluster of aftershocks south of the city of Bam is distributed just under the minor surface ruptures in the desert. The 3-D velocity structure shows a thick layer of high V_S and low σ (minimum: 0.20) at a depth range of 2–6 km. The deeper layer, with a thickness of about 2 km, appears to have a low V_S and high σ (maximum: 0.28) from 6 km depth beneath Bam to a depth of 9 km south of the city. The inferred increase of Poisson's ratio from 2 to 10 km in depth may be associated with a change from rigid and SiO₂-rich rock to more mafic rock, including the probable existence of fluids. The main seismic gap of aftershock distribution at the depth range of 2 to 7 km coincides well with the large slip zone in the shallow thick layer of high V_S and low σ. The large slip propagating mainly in the shallow rigid layer may be one of the main reasons why the Bam area suffered heavy damage.     

Estimation of freeboard requirements against overtopping of surface impoundments under seismic action

The excitation of structural components and liquid contents of surface impoundments by seismic waves can generate turbulence that is large enough to overtop the bounding berms. In cases in which the liquids are wastes from industrial/municipal operations, their release from impoundments can pose significant risks to the environment. In this analysis, the freeboard magnitudes that can accommodate liquid head levels in impoundments are determined through linkage of configuration of waves in the liquid surface to incident seismic wave characteristics, liquid characteristics and impoundment design. For an impoundment site in a region of ground acceleration levels ranging from 0.2 to 1.0 g and impacted by seismic shear wave velocity of 180 m/s, freeboard requirements are in the range of 0.004–2.0 m on soft soil; 0.008–0.7 m on medium-dense soil; and 0.002–0.1 m for dense soil. For the same impoundment design, ground acceleration and incident wave characteristics, freeboard requirements are directly proportional to the depth of the soil mantle over bedrock. The impoundment slope, which is a key parameter with regards to liquid holding volumetric capacity of the impoundment, is a less significant parameter than depth to bedrock with regard to the size of the required freeboard. This implies that siting of an impoundment should be considered to be critical to impoundment performance in seismic zones.     

Examination of loose saturated sands impacted by a heavy tamper

This article examines the densification effects on the loose saturated sands impacted by a heavy steel tamper dropped from a great height (i.e., deep dynamic compaction, DDC). This examination was achieved by carrying out a series of piezocone penetration test (CPTu) soundings before and after the DDC impact. The depths at which densification took place ranged from 6.5 to 9.5 m below the ground surface (BGS) after one pass of DDC, and from 7.5 to 11.0 m BGS after two passes. The propagation of the surface waves generated in DDC disturbed the top 0.3–1.3 m soils. Directly below this disturbed layer, it was the most densified soil layer at the depths of 1.7–4.5 m BGS. The existence of the residual soft peat pockets reduced the densification effects substantially. Both the strength and the stiffness of the loose saturated sands were significantly improved after the DDC treatment. After two passes of impact, the liquefiable soils were densified to the level of unliquefiable along with dramatic reduction in liquefaction probabilities when subjected to earthquake motions.     

Interaction of monsoonal wave, current and tide near Gopalpur, east coast of India, and their impact on beach profile: a case study

A 97-day-long record on waves and currents was obtained using wave rider buoy and current meter moored at 2.5 km off Gopalpur from 19 May to 23 August 2008 representing southwest monsoon months. A Valeport tide gauge was used to record water level at Gopalpur port. Simultaneously, beach profiles at 4 transects were monitored using real-time kinematic (RTK) global positioning system (GPS). A total of 636,167 waves were analyzed for the period; a range of 3,200–9,700 waves approach the coast in an individual day. During the study, unusual characteristics of wave were observed on July 29, 2008, with a magnitude of significant wave height, H_s = 2.85 m, maximum wave height, H_max = 5.22 m, and peak wave period, T_p = 10.2 s, and on August 11, 2008, with H_s = 2.28 m, H_max = 5.37 m, and T_p = 11.1 s. Significant beach loss was noticed during these periods, and severe erosion was recorded on August 1, 2008. Beach profile data indicates that 18–58 cu. m/m sediment was lost during the study period. The paper provides an overview of the statistical analysis of wave heights, periods, direction, and spectral energy density and explains the cause of coastal erosion and loss of sediment.     

On the nature of the excess heat capacity of mixing

The excess vibrational entropy (ΔS _vib^ex) of several silicate solid solutions are found to be linearly correlated with the differences in end-member volumes (ΔV _i ) and end-member bulk moduli (Δκ _i ). If a substitution produces both, larger and elastically stiffer polyhedra, then the substituted ion will find itself in a strong enlarged structure. The frequency of its vibration is decreased because of the increase in bond lengths. Lowering of frequencies produces larger heat capacities, which give rise to positive excess vibrational entropies. If a substitution produces larger but elastically softer polyhedra, then increase and decrease of mean bond lengths may be similar in magnitude and their effect on the vibrational entropy tends to be compensated. The empirical relationship between ΔS _vib^ex, ΔV _i and Δκ _i , as described by ΔS _vib^ex = (ΔV _i  + mΔκ _i )f, was calibrated on six silicate solid solutions (analbite–sanidine, pyrope–grossular, forsterite–fayalite, analbite–anorthite, anorthite–sanidine, CaTs–diopside) yielding m = 0.0246 and f = 2.926. It allows the prediction of ΔS _vib^ex behaviour of a solid solution based on its volume and bulk moduli end-member data.     

S-waves profiles from noise cross correlation at small scale

Cross correlations of ambient seismic noise recordings are studied to infer shear-wave velocities (V_S) profiles versus depth. Experiments are performed, over inter-station distances ranging from 60 m to about 400 m, in the crowded and noisy historical centre of Napoli, where the conditions for the use of active (controlled source) seismic spreadings are prohibitive, even for just one receiver. From the noise cross correlation, group velocity dispersion curves are extracted, with FTAN method, and their non-linear inversion supplies V_S profiles versus depth. The information of nearby stratigraphies and the range of V_S variability for samples of Neapolitan soils and rocks confirms the validity and reliability of the results obtained with our expeditious procedure. If successfully tested in other geological settings, the proposed approach is a low cost methodology to get reliable V_S velocity profiles versus depth.     

Site classification of Pondicherry using shear-wave velocity and horizontal-to-vertical spectral ratio

Site classification studies play a vital role in earthquake hazard assessment since in situ ground conditions substantially affect the characteristics of incoming seismic waves during earthquakes. Flat areas along the coast and rivers generally consist of thick layers of soft clay and sand. Such deposits amplify certain frequencies of ground motion, thereby attributing to an increase in the damage due to an earthquake. Hence, site classification studies have been carried out using shear-wave velocity, ground response, and corresponding amplification at 83 locations in Pondicherry, a coastal city in India. The present study is aimed at estimating the shear-wave velocity through multichannel analysis of surface waves and to compute the average shear-wave velocity (V _S ³⁰ ), stiffness, and N values using empirical relations. Further, site-response studies (horizontal-to-vertical spectral ratio) were conducted to estimate the ground-response frequencies and corresponding amplifications through Nakamura technique. From the results, the study area was classified into three types, i.e., C-class: with V _S ³⁰ in the range of 360–760 m/s, D-class: with V _S ³⁰ in the range of 180–360 m/s, and E-class: with V _S ³⁰  < 180 m/s following the National Earthquake Hazard Reduction Programme norms (BSSC in NEHRP recommended provisions for seismic regulations for new buildings and other structures (FEMA 450), part 1: provisions. Building Seismic Safety Council for the Federal Emergency Management Agency, Washington, 2003). Finally, a site classification map for Pondicherry region has been prepared, which can be used in urban planning and strengthening of existing structures against future earthquakes.     

Assessing shear wave velocity profiles using multiple passive techniques of Shillong region of northeast India

Shillong region of northeast India falls under seismic zone V. Being a commercial hub, urbanization in this study region is at its peak. In order to qualitatively assess the subsurface velocity profiling of this area, we have blended two robust techniques, namely spatial autocorrelation (SPAC) and frequency wavenumber (FK) method. Corresponding to array noise data collected at five sites, situated in the close proximity of boreholes, we have evaluated V_S and V_P as well. The shear wave velocity estimates yielded by these techniques are found to be consistent with each other. The computed V_s values up to depth of 30 m are observed to be in the range of 275–375 m/s, in most of the sites which implies prevalence of low-velocity zone at some pocket areas. The estimates so found are systematically analyzed and implications are outlined. The results were corroborated by substantial evidence of site geology as well as geotechnical information.     

Effect of Source Energy for SASW Testing on Geological Sites

A number of Rayleigh wave tests were performed on two geological sites by employing a cylindrical mass of 65 kg dropped from a height ranging from 1 to 4 m. For each test, the mass was dropped freely either (1) directly on ground surface, or (2) on a steel circular base plate kept on the ground. Various combinations of source to first receiver distance (S) and receiver spacing (X) were employed. It has been noted that the value of λ _max increases continuously with an increase in the source energy; where λ _max refers to the maximum wavelength up to which the shear wave velocity profile can be obtained with the usage of the spectral analysis of surface waves tests. The inclusion of the steel base plate below the dropping mass leads to a further increase in the value of λ _max . It is also observed that, for the same height of fall, a ground stratum with relatively greater stiffness tends to provide an increased value of λ _max .