Field monitoring of groundwater responses to heavy rainfalls and the early warning of the Kualiangzi landslide in Sichuan Basin,southwestern China

The Kualiangzi landslide was triggered by heavy rainfalls in the “red beds” area of Sichuan Basin in southwestern China. Differing from other bedrock landslides, the movement of the Kualiangzi landslide was controlled by the subvertical cracks and a subhorizontal bedding plane (dip angle < 10°). The ingress of rainwater in the cracks formed a unique groundwater environment in the slope. Field measurement for rainfall, groundwater movement, and slope displacement has been made for the Kualiangzi landslide since 2013. The field monitoring system consists of two rainfall gauges, seven piezometers, five water-level gauges, and two GPS data loggers. The equipments are embedded near a longitudinal section of the landslide, where severe deformation has been observed in the past 3 years. The groundwater responses to four heavy rainfall events were analyzed between June 16 and July 24 in 2013 coincided with the flood season in Sichuan. Results showed that both of the water level and the pore-water pressure increased after each rainfall event with delay in the response time with respect to the precipitation. The maximum time lag reached 35 h occurred in a heavy rainfall event with cumulative precipitation of 127 mm; such lag effect was significantly weakened in the subsequent heavy rainfall events. In each presented rainfall event, longer infiltration period in the bedrock in the upper slope increased the response time of groundwater, compared to that of in the gravels in the lower slope. A translational landslide conceptual model was built for the Kualiangzi landslide, and the time lag was attributed to the gradual formation of the uplift pressure on the slip surface and the softening of soils at the slip surface. Another important observation is the effect on the slope movement which was caused by the water level (H _w) in the transverse tension trough developed at the rear edge of the landslide. Significant negative correlation was found for H _w and the slope stability factor (F _s), in particular for the last two heavy rainfall events, of which the drastic increase of water level caused significant deterioration in the slope stability. The rapid drop (Δ?=?22.5 kPa) of pore-water pressure in the deep bedrock within 1 h and the large increase (Δ?=?87.3 mm) of surficial displacement were both monitored in the same period. In the end, a four-level early warning system is established through utilizing H _w and the displacement rate D _r as the warning indicators. When the large deformation occurred in flood season, the habitants at the leading edge of the landslide can be evacuated in time.     

Analysis of an anti-dip landslide triggered by the 2008 Wenchuan earthquake in China

The Guantan landslide, with a total displaced mass of about 468 × 10⁴ m³, was triggered by the 2008 Wenchuan earthquake and succeeding rainfall in Jushui Town, Sichuan Province, China. The landslide occurred on an anti-dip hard rock slope with a weak rock founding stratum of 200 m in thickness. To investigate the failure mechanism of the Guantan landslide, dynamic behaviors of hard and soft rock slopes were investigated by means of large scale shaking table tests. The laboratory models attempted to simulate the field geological conditions of the Guantan landslide. Sinusoidal waves and actual seismic waves measured from the Wenchuan Earthquake were applied on the slope models under 37 loading configurations. The experimental results indicated that deformation mainly developed at a shallow depth in the upper part of the hard rock slope and in the upper (near the crest) and lower (near the toe) parts of the soft rock slope. An equation for predicting the depth of sliding plane was proposed based on the location of the maximum horizontal acceleration. Finally, it was concluded that the failure process of the Guantan landslide occurred in three stages: (1) toppling failure caused by compression of the underlying soft rock strata, (2) formation of crushed hard rock and sliding surface in soft rock as the result of seismic shocks, particularly in the horizontal direction, and (3) aftershock rainfall accelerates the process of mass movement along the sliding plane.     

Analysis of a progressive slope failure in the Xiangjiaba reservoir area,Southwest China

The rehabilitation construction in the reservoir area of Xiangjiaba hydropower station in Southwest China has caused many landslides. A shallow progressive failure that occurred on the resettlement site of Xin’an Town of Pingshan County in Sichuan Province was selected as a case study. This landslide occurred in a long and gently inclined area by slope excavation under rainfall conditions. It is about 3.0 m deep with a total length of 35 m and is composed of some subfailures. Undisturbed samples were retrieved, on which the basic properties, shear strength, expansive potential, mineral compositions, and microstructures were tested and analyzed. The results show (1) the landsliding materials belong to medium expansive soil, consisting of the clay minerals of illite–smectite (I/S) and chlorite–smectite (C/S); (2) shear strength of the soil is sensitive to water, which greatly decreases once saturated; and (3) many fractures and relatively large pores are developed in the soils. Back analysis of the landslide shows that the shear strength at failure is less than the residual shear strength obtained from lab tests, indicating that some processes contributing to the slope failure could not be reflected by the shear box test. Based on the above analysis, the progressive process of the slope failure was interpreted, and it is inferred that the rainfall entered into the slope mainly through fractures and relatively large pores in the soil. It caused not only the great decrease in soil strength but also the swelling trend. The latter one would lead to growth, interaction, and coalescence of the fractures. Soon after, these fractures formed the shear planes (zones), which further decreased the resistance of the landslide. Under these favorable conditions, the slope excavation directly triggered the failure.     

Evolution Mechanism and Rainfall Warning Criteria for Maijianwo Slope in Henan Province,China

In this study, two different research methods are applied to investigate the evolution mechanism and rainfall warning criteria for Maijianwo slope located in Henan Province, China. On the one hand, an indoor-model test is performed under artificial rainfall and based on similarity theory. A set of monitoring system is utilized to track the moisture content, deformation and cracks of critical points of the model during the test. On the other hand, the numerical simulation is carried out to provide an insight into the variation of unstable zone and factor of safety for the landslide with the increasing cumulative rainfall. Results indicate that the evolution process of Maijianwo slope is composed of three stages of initiating, accelerating and failure respectively, and stability of slope decreases gradually as cumulative rainfall increases. Based on the evolution mechanism of retrogressive landslide verified by both model test and numerical simulation, cracking time of critical positions on the slope prior to each stage were set as the initiating time of each stage and the cumulative rainfall associated with each initiating time (E₁ = 75 mm, E₂ = 180 mm) has been defined as the warning criteria for the Maijianwo slope. As the cumulative rainfall in Maijianwo slope reaches 75 and 180 mm, the landslide orange and red warning codes are issued, respectively. Otherwise, the slope is in a safe condition when the cumulative rainfall is less than 75 mm.     

Response of a loess landslide to rainfall: observations from a field artificial rainfall experiment in Bailong River Basin,China

Rainfall-induced landslides are a significant hazard in many areas of loess-covered terrain in Northwest China. To investigate the response of a loess landslide to rainfall, a series of artificial rainfall experiments were conducted on a natural loess slope, located in the Bailong River Basin, in southern Gansu Province. The slope was instrumented to measure surface runoff, pore water pressure, soil water content, earth pressure, displacement, and rainfall. The hydrological response was also characterized by time-lapse electrical resistivity tomography. The results show that most of the rainfall infiltrated into the loess landslide, and that the pore water pressure and water content responded rapidly to simulated rainfall events. This indicates that rainfall infiltration on the loess landslide was significantly affected by preferential flow through fissures and macropores. Different patterns of pore water pressure and water content variations were determined by the antecedent soil moisture conditions, and by the balance between water recharge and drainage in the corresponding sections. We observed three stages of changing pore water pressure and displacement within the loess landslide during the artificial rainfall events: Increases in pore water pressure initiated movement on the slope, acceleration in movement resulting in a rapid decrease in pore water pressure, and attainment of a steady state. We infer that a negative pore water pressure feedback process may have occurred in response to shear-induced dilation of material as the slope movement accelerated. The process of shear dilatant strengthening may explain the phenomenon of semi-continuous movement of the loess landslide. Shear dilatant strengthening, caused by intermittent or continuous rainfall over long periods, can occur without triggering rapid slope failure.     

Comprehensive analyses of the initiation and landslide-generated wave processes of the 24 June 2015 Hongyanzi landslide at the Three Gorges Reservoir,China

Reservoir landslides pose a great threat to shipping safety, human lives and properties, and the operation of the hydropower station. In this paper, the 24 June 2015 Hongyanzi landslide at the Three Gorges Reservoir is considered as an example to study the initiation mechanism and landslide-generated wave process of a reservoir landslide. The finite difference method and limit equilibrium analysis are used to analyze the deformation and failure characteristics of the Hongyanzi slope. Simulation results show that a large deformation (about 358 mm) happens in the shallow deposits under intermittent rainfall condition, and the slope is in a limit state. At the same time, continuous rapid drawdown of the water level (about ?0.55 m/day during 8–24 June 2015) reduced the support and accelerated the drainage of the water for the bank slope. A coupling effect of intermittent rainfall and rapid drawdown of the water level was the triggering factor of the 24 June Hongyanzi landslide. Landslide-generated wave process was simulated using a fluid–solid coupling method by integrating the general moving object collision model. Simulation results show that the landslide-generated wave is dominated by the impulse wave, which is generated by sliding masses entering the river with high speed. The maximum wave height is about 5.90 m, and the wave would decay gradually as it spreads because of friction and energy dissipation. To prevent reservoir landslides, the speed for the rising or drawdown of the water level should be controlled, and most importantly, rapid drawdown should be avoided.     

Flow-type landslides in pyroclastic soils on flysch bedrock in southern Italy: the Bosco de’ Preti case study

In the last 20 years, major efforts have been made to investigate shallow flow-type landslides. Such phenomena are usually rainfall-induced and in the geological context of Campania (Southern Italy) occur in pyroclastic soils resting on steep slopes mainly constituted by carbonate or volcanic bedrock and by flysch deposits. They are generally complex landslides with an early soil slide and a subsequent flow evolution. In this paper, a database of flowslides occurring in recent years within the flysch deposits of Avellino (Campanian Apennines) is first discussed and then the case study of Bosco de’ Preti landslide on March 4, 2005, is described. The geological and geotechnical characteristics of the soils involved are described and the monitoring of the groundwater heads collected over 1 year from June 2005 to June 2006 is also shown. The last part of the paper illustrates the results of numerical modelling of the landslide triggering to gain insights into such phenomena. Slope stability analyses are preceded by hydrological modelling of the slope based on the monitoring data. Numerical analysis demonstrated that the rainfall during the 2 months preceding the event was able to fully saturate the pyroclastic cover and to establish positive pore water pressure at the depth of the surface of rupture, a soil condition never witnessed in carbonatic contexts. Hence, a combination of antecedent (predisposing factors) and single rainfall events (triggering factors) led to slope failure, as usually happens in pyroclastic soils in carbonatic and volcanic contexts. Finally, analysis of the historical landslides together with detailed investigation of the Bosco de’ Preti case study permitted comparison between flow-type landslides in pyroclastic soils on carbonatic/volcanic bedrock and those on flysch.     

The January 10, 1997 Pozzano landslide, Sorrento Peninsula, Italy

From 1997 to 1999, a huge number of slides, often turning into extremely rapid debris-earth flows, repeatedly affected the late Quaternary volcaniclastic deposits mantling the carbonate slopes of Campania region, Italy. The Sorrento Peninsula was the epicentral district of the 1997 regional slope-instability crisis. Some hundred shallow mass movements took place during January 1997 in this area. These were the last episode of a long series of slope failure events dating back to mid-18th century. Results from geological and geomorphologic surveys are presented. Landslide mechanism and triggering factors are analysed for the most important mass movement, which occurred during the January 9-11, 1997, regional event. On January 10, 1997, at about 8:15 PM, a rainfall-induced debris slide-debris flow occurred at Pozzano (province of Naples), mainly affecting the 79 AD pyroclastic products. Following a J-path, the landslide destroyed a private house and invaded the State Road no. 145. This event resulted in four deaths, 22 persons injured and road closure for about 2 months. There was less than 200 mm of rainfall in the 72-h period prior to the landslide, although intense precipitation had occurred during a preceding 4-month period. However, the slope failure event was not preceded by an extreme short-term antecedent rainfall, as already noticed in previous landslides of this type in Campania. Finally, following a preliminary geotechnical characterization of volcaniclastic soils, a slope-stability back analysis was carried out, which adopted the classical infinite slope scheme. This analysis gave further evidence of the role played by pore pressure in reducing the overall shear strength of pyroclastic soils.     

Mechanism and failure process of Qianjiangping landslide in the Three Gorges Reservoir,China

The Qianjiangping landslide is a large planar rock slide which occurred in July 14, 2003 shortly after the water level reached 135 m in the Three Gorges Reservoir, China. The landslide destroyed 4 factories and 129 houses, took 24 lives, and made 1,200 people homeless. Field investigation shows that the contributing factors for the landslide are the geological structure of the slope, the previous surface of rupture, the water level rise, and continuous rainfall. In order to reveal the mechanism and failure process of the landslide, numerical simulation was conducted on Qianjiangping slope before sliding. Based on the characteristics and the engineering conditions of the landslide, the topography and the geological profiles of Qianjiangping slope before sliding is reconstructed. The seepage field of Qianjiangping slope before sliding was simulated with the Geostudio software. The results show that ground water table rises and bends to the slope during the rise of water level, and the slope surface becomes partially saturated within the period of continuous rainfall. Using the ground water table obtained above, the failure process of Qianjiangping slope is simulated with the Flac3D software. The results demonstrate that the shear strain increment, displacement, and shear failure area of the slope increased greatly after the water level rose and continuous rained, and the landslide was triggered by the combined effect both of water level rise and continuous rainfall. The development of shear strain increment, displacement, and shear failure area of the slope shows that the landslide was retrogressive in the lower part of the slope and progressive in the upper part of the slope.     

Topographical features of rainfall-triggered landslides in Mon State,Myanmar, August 2019: spatial distribution heterogeneity and uncommon large relative heights

Continuous 5-day (August 4–9, 2019) torrential rainfall in the monsoon season triggered more than 90 landslides on northwest-southeast extended mountain range of Mon State, Myanmar. In this study, remote sensing images, DEM, and limited fieldworks were used to create the landslide inventory. The topography features of these landslides are analyzed via ArcGIS. The largest one occurred on 9 August 2019 and caused 75 deaths and 27 buildings were damaged. This landslide occurred on gentle topography (slope angle, 23°) with long run-out, in which the angle of reach was relatively low (10°). The volume was 111,878 m³ was mainly composed of weathered granite and red soil and the sliding depth was approximately 7.5 m. Topographic characteristics including the relative slope height, angle of reach, and slope angle of source area of 35 landslides with areas?>?4000 m² were analyzed. The spatial distribution characteristics and topographic features of the 35 landslides below are distinguished: (1) the concentration of most of landslides on southwest-facing slopes showing the heterogeneous spatial distribution of landslide; (2) an uncommon landslide distribution in which more than half of landslide originates from upper slope; (3) the range of the angle of the source area (17°–38°) compatible with the internal friction angle of soils in tropical regions (17°–33°); and (4) the tangent of the angle of reach is generally smaller than 0.5 (angle of reach?<?27°) shows a relative high mobility and the relation between landslide mobility and the slope angle of the landslide source area is similar to the one of earthquake-triggered landslides, even though the triggering mechanism, landslide type, and landslide volume are dramatically different.

     

Failure Mechanism of a Shallow Landslide at Tun-Sardon Road Cut Section of Penang Island,Malaysia

The occurrences of shallow landslides in residual soils of Penang hilly areas are common in rainy days. The failure mechanisms of a shallow landslide occurred at km 3.9 road in Tun-Sardon area of Penang Island have been simulated using two different methods of slope stability analysis. The results indicate that the failure was initiated locally inside the slope and then propagated further to induce total failure. The failure propagation was started from initial local failure zone and was driven by mobilized shear strength along the shear plane. The slope was marginally stable with an overall factor of safety of 1.32 before it failed to a rainfall event on September 6, 2008. It is found from back calculation that the rain infiltration raised the temporary water level and reduced the shearing strength of soil to a minimum level with increased pore water pressure to trigger the failure. This paper suggests further research on shallow landslide of Penang Island considering the direct rainfall infiltration effect in terms of groundwater pressure-head distribution inside the slope.     

多工况下汉源二蛮山滑坡机理数值模拟

利用FLAC3D软件对四川省雅安市汉源县二蛮山滑坡坡体进行建模,模拟降雨滑坡过程,并进行应力应变特征及稳定性计算分析,从而为深入研究地震及降雨诱发再次滑坡及防灾减灾提供可靠依据。研究中假设地震工况,对边坡进行详细的动力分析,得到了各监测点动力特征曲线;通过降雨工况下坡体稳定性系数分析得到了不同强度折减安全系数。研究结果表明,滑源区相对特殊的地形条件和地质构造以及不利的结构面组合是滑坡的基础;前期强降雨期间饱水加载以及大量雨水沿斜沟张裂结构面的下渗软化作用,是诱发滑坡发生的关键因素。      

An experimental and numerical study of a landslide triggered by an extreme rainfall event in northern Australia

In February/March 2007, an extreme rainfall event occurred in the Jabiru region of the Northern Territory of Australia. Rainfall of 784 mm fell in a 72-h period. This rainfall event resulted in 49 separate landslides occurring in the adjacent, but remote and inaccessible region of Arnhem Land. The landslides were extensively mapped and characterised. A common feature of the landslides was their relatively surficial nature. This paper reports on laboratory and field tests to characterise the material properties of the slide material and the underlying, more competent material. One particular, large and relatively accessible landslide was chosen for detailed investigation. The experimental data are used to carry out seepage and slope stability analyses, taking account of changes in the degree of saturation (and thus the negative pore water pressure or suction) in the slope material during the rainfall event in question. Using a parametric study in which various material parameters were varied around the measured mean values, it is shown that the failure of this particular slope could have been predicted using relatively straightforward seepage and limit equilibrium slope stability analyses, coupled with the relevant rainfall data, as long as the contribution of matric suction to the engineering characteristics of the slope material was accounted for. The work also highlights the importance of in situ conditions at the time a particular rainfall event (particularly an extreme event such as that considered in this paper) occurs. If the slope has a relatively high degree of saturation, manifested as a low initial in situ suction, it is more susceptible to rainfall triggering a slope failure. Although this observation is not novel, the investigation described in this paper confirms the importance of ambient in situ conditions and provides an indication of how the likelihood of landslide occurrence at this particular site may in the future be quantified, i.e. by focussing on antecedent rainfall history.     

南京市浦口区某山前缓坡滑坡复活机制再分析

南京猪头山滑坡属于典型的覆盖层滑坡,2003年5月边坡发生缓慢变形失稳,没有对周围造成很大的危害,故未引起足够重视,2016年6~7月间受强降雨的影响再次发生大规模的滑动。研究发现,该滑体的地层具有特殊地质结构,在强降雨条件下会产生暂时性承压水,在其承压水的渗透力及浮托力作用下,其稳定性将会大大下降,因此该滑坡的再滑动与降雨密切相关。本文运用数值模拟方法分析了滑坡变形过程与降雨时长及降雨强度之间的关系,结果表明猪头山山前缓坡的稳定性随降雨时长和降雨强度增大逐渐降低,且具有一定的突变性,其滑坡面的位置位于坡体填土层的下部,较好地揭示了猪头山降雨型滑坡形成的机理以及滑坡再滑动机制。这一研究为所在地区的降雨性滑坡预报和治理提供了科学依据。     

Shear strength characterization of municipal solid waste at the Suzhou landfill, China

The current practice of slope stability analysis for a municipal solid waste (MSW) landfill usually overlooks the dependence of waste properties on the fill age or embedment depth. Changes in shear strength of MSW as a function of fill age were investigated by performing field and laboratory studies on the Suzhou landfill in China. The field study included sampling from five boreholes advanced to the bottom of the landfill, cone penetration tests and monitoring of pore fluid pressures. Twenty-six borehole samples representative of different fill ages (0 to 13 years) were used to perform drained triaxial compression tests. The field and laboratory study showed that the waste body in the landfill can be sub-divided into several strata corresponding to different ranges of fill age. Each of the waste strata has individual composition and shear strength characteristics. The triaxial test results showed that the MSW samples exhibited a strain-hardening and contractive behavior. As the fill age of the waste increased from 1.7 years to 11 years, the cohesion mobilized at a strain level of 10% was found to decrease from 23.3 kPa to 0 kPa, and the mobilized friction angle at the same strain level increasing from 9.9° to 26°. For a confinement stress level greater than 50 kPa, the shear strength of the recently-placed MSW seemed to be lower than that of the older MSW. This behavior was consistent with the cone penetration test results. The field measurement of pore pressures revealed a perched leachate mound above an intermediate cover of soils and a substantial leachate mound near the bottom of the landfill. The measurements of shear strength properties and pore pressures were utilized to assess the slope stability of the Suzhou landfill.     

降雨诱发填方路堤边坡变形机制物理模拟研究

填方路堤变形失稳是西部山区工程建设的常见问题。重庆某高速公路边坡为典型的堆载条件下降雨诱发型滑坡,填方堆载后,填方边坡在连续降雨条件下,沿基岩之上的软弱面产生滑动破坏。定性分析认为,降雨在滑坡形成中起着关键作用,为了研究填方边坡在降雨条件下的变形破坏机制及孔隙水压力与变形之间的关系,采用物理模拟方法研究边坡变形失稳的全过程,分析孔隙水压力随降雨时间的变化规律及其与变形破坏的关系。研究结果表明：边坡后缘大方量堆载,改变了其应力条件,是滑坡产生的主要因素。场地施工改变了原有的地表水环境,连续强降雨致使大量下渗的雨水,不仅显著改变坡体应力条件,而且雨水沿着滑面运移软化滑带,是滑坡产生的重要诱发因素。孔隙水压力在坡体失稳过程中起着关键作用,填方体土碎屑、泥质含量大,下渗的雨水携带上部细小颗粒及滑带泥质成分至滑带附近,堵塞地下水消散通道,表现为坡体变形积累,孔隙水压力增加;边坡变形陡增,孔隙水压力降低。该滑坡破坏分为降雨下渗、滑带饱水软化、后缘产生裂缝、裂缝贯通-整体滑动4个阶段,为蠕滑-拉裂式滑坡。     

低山丘陵区典型滑坡-泥石流链生灾害特征与成灾机理

2019年6月10—13日,龙川县发生持续强降雨,导致全县境内发生大量滑坡、泥石流灾害,贝岭镇米贝村是三个重灾区之一。本文以贝岭镇米贝村6号沟发生的滑坡-泥石流链生灾害为研究对象,在野外精细化调查测量基础上,结合数值模拟分析与计算,对链生灾害特征与成灾机理展开研究。研究发现:①6号沟内共发育7处浅层土质小型滑坡,仅3号滑坡体与部分6号滑坡体转化为泥石流,构成泥石流主要物源,其余滑坡未构成持续性影响;②持续降雨下渗,坡体由非饱和向饱和状态转变,坡表形成连续饱和区,孔隙水压力的增加与孔隙水的软化促使土体强度降低,加之坡体饱和自重的增大,斜坡发生浅表层失稳破坏;③降雨的持续下渗与支沟沟源“漏斗状”地形下的地表汇水快速增大滑坡松散堆积体内的含水率,促使其物理性质发生变化,在重力势能下呈流态状启动、运动转化为泥石流。降雨结构影响滑坡-泥石流链生过程,前期降雨引发滑坡、后期降雨启动形成泥石流,滑坡与泥石流的发生表现出阶段性特征。研究成果有助于指导当地政府进一步开展滑坡-泥石流链生灾害的防灾减灾工作,也为该地区未来区域预警研究工作提供理论支撑。     

Formation process of two massive dams following rainfall-induced deep-seated rapid landslide failures in the Kii Peninsula of Japan

Extreme heavy rainfall due to Typhoon Talas on September 2–4, 2011 in the Kii Peninsula, Japan, triggered numerous floods and landslides. This study investigates the mechanism and the entire process of rainfall-induced deep-seated landslides forming two massive dams in the Kuridaira and Akatani valleys, respectively. The mechanism of the rapid deep-seated landslides is examined through a series of laboratory experiments on samples from sliding surfaces by using undrained high-stress dynamic-loading ring-shear apparatus. The test results indicate that the failure of samples is triggered by excess pore water pressure generation under a shear displacement from 2 to 7 mm with a pore pressure ratio ranging from 0.33 to 0.37. The rapid movement of landslides is mainly attributed to high mobility due to the liquefaction behavior of both sandstone-rich and shale samples. Geomorphic settings and landslide mobility are major contributing factors to the dam formation. Additionally, shear displacement control tests show that a certain amount of shear displacement between 2 and 7 mm along the sliding surfaces of the gravitationally deformed slopes might have led to the failures. Importantly, computer simulation with LS-RAPID software using input parameters obtained from physical experiments is employed to interpret the entire formation process of the abovementioned two landslide dams. The simulation results are examined in accordance with the observed on-site geomorphic features and recorded data to explain the possibility of sliding processes. The results further point out that local failures are initiated from the lower middle part of the landslide bodies where the geological boundary exists. This condition most probably influences the landslide initiation in the two case studies. This research is therefore helpful for hazard assessment of slopes that are susceptible to deep-seated landslides and other sequential processes in areas with geology and geomorphology similar to that of the Kii Peninsula.     

Time evolution and spatial accumulation of progressive failure for Xinhua slope in the Dagangshan reservoir,Southwest China

This paper presents a preliminary study of time evolution and spatial accumulation of progressive failure for ancient landslide deposits in Xinhua slope. According to the geological response after impoundment, the Xinhua slope has shown the spatial accumulation of deformation, such as ground cracks in the rear edge, toe collapse, local shallow slides in intense rainfall, and progressive creep displacement. Approximately 2 years of monitoring was performed for the Xinhua slope with the assistance of the global navigation satellite system (GNSS), unmanned aerial vehicles (UAVs), and field investigations. The deformation process of a reservoir landslide is considered to be a comprehensive and complicated combination of geological influence from various adverse factors. Field investigations and monitoring indicate that the major serious influence after completion of dam construction comes from the initial large-scale impoundment, the fluctuation of water level, and the existence of a flood season. The creep/slip deformation of slope deposits is a result of integration with adverse hydraulic conditions, e.g., strong rainfall, intense currents and transient seepage flow inside the slope deposits, and activation by water level fluctuation, which can be verified from the twofold evident deformation in the flood season. For the reservoir with daily regulation ability, the occurrence of evident deformations in July highlights that the regulation plan for water level in the flood season is important for controlling the deformation of slope deposits, where the fluctuation of the water level is no more than 10 m in the operation period.     

Risk management study on impulse waves generated by Hongyanzi landslide in Three Gorges Reservoir of China on June 24, 2015

On June 24, 2015, Hongyanzi slope located in Wushan County of the Three Gorges Reservoir collapsed, generating 5–6-m-high impulse waves, which overturned 13 boats, killed 2 persons, and injured 4 persons. It is the second incident of landslide-generated impulse waves since the 175-m experimental impoundment in 2008. The emergency investigation shows that Hongyanzi landslide is a bedding soil landslide with a volume of 23?×?10⁴ m³ induced by a series of triggering factors such as rainfall, flooding upstream, and reservoir drawdown. The nonlinear Boussinesq water wave model is used to reproduce the impulse waves generated by the landslide of June 24th. The numerical simulation results suggest that the wave propagation process was influenced by the T-shaped geomorphic conditions of river valley, and the coastal areas in the county seat were the major wave-affected areas, which is opposite to the landslide. The numerical wave process accord well with the observed incident, and the investigation values were in good agreement with the calculated values. Moreover, the worst-case scenario of the 7?×?10⁴ m³ deformation mass beside Hongyanzi landslide is potential to generate impulse waves, which was predicted with the same numerical model. This adjacent deformation mass will probably generate impulse waves with maximum height and run-up of 2.2 and 2.0 m, respectively, and only a very few areas in the water course had waves rising to a height of 1 m or above. The research results provide a technical basis for emergency disposal to Hongyanzi landslide and navigation restriction in Wushan waterway. More importantly, it pushes the risk management of the navigation based on the impulse wave generated by landslide. It is advised that the Three Gorges Reservoir and other reservoirs around the world should put more efforts in performing special surveys and studies on the potential hazards associated with landslide-generated impulse waves.