Bed scour by debris flows: experimental investigation of effects of debris‐flow composition

Debris flows can grow greatly in size by entrainment of bed material, enhancing their runout and hazardous impact. Here, we experimentally investigate the effects of debris‐flow composition on the amount and spatial patterns of bed scour and erosion downstream of a fixed to erodible bed transition. The experimental debris flows were observed to entrain bed particles both grain by grain and en masse, and the majority of entrainment was observed to occur during passage of the flow front. The spatial bed scour patterns are highly variable, but large‐scale patterns are largely similar over 22.5–35° channel slopes for debris flows of similar composition. Scour depth is generally largest slightly downstream of the fixed to erodible bed transition, except for clay‐rich debris flows, which cause a relatively uniform scour pattern. The spatial variability in the scour depth decreases with increasing water, gravel (= grain size) and clay fraction. Basal scour depth increases with channel slope, flow velocity, flow depth, discharge and shear stress in our experiments, whereas there is no correlation with grain collisional stress. The strongest correlation is between basal scour and shear stress and discharge. There are substantial differences in the scour caused by different types of debris flows. In general, mean and maximum scour depths become larger with increasing water fraction and grain size, and decrease with increasing clay content. However, the erodibility of coarse‐grained experimental debris flows (gravel fraction = 0.64) is similar on a wide range of channel slopes, flow depths, flow velocities, discharges and shear stresses. This probably relates to the relatively large influence of grain‐collisional stress to the total bed stress in these flows (30–50%). The relative effect of grain‐collisional stress is low in the other experimental debris flows (<5%), causing erosion to be largely controlled by basal shear stress. Copyright © 2016 John Wiley & Sons, Ltd.     

Spatial and temporal diversity for debris‐flow meteorological control in subarctic oceanic periglacial environments in Iceland

Slopes in fjord environments of Iceland are prone to debris‐flow initiation, responding to a wide variety of meteorological triggering factors, such as rain on snow, rapid snowmelt, long‐lasting rainfall or intense rainfall. If all fjord regions have similar debris flows with regards to their magnitude, their meteorological control is diverse both in space and in time. Debris flows in Northwest Iceland are triggered mostly by rain‐on‐snow and long‐lasting rainfall, while snowmelt is more characteristic in North Iceland, and rainfall has a clear impact in East Iceland. Most debris‐flow events occur on a single slope, and only a few are recorded at the same time in different regions. Observations of the threshold values underline the diversity of debris‐flow initiation, occurring with huge amounts of sudden water supply as well as with very moderate ones. Copyright © 2007 John Wiley & Sons, Ltd.     

Field observations,rheological testing and numerical modelling of a debris‐flow event

Debris flows generated from landslides are common processes and represent a severe hazard in mountain regions due to their high mobility and impact energy. We investigate the dynamics and the rheological properties of a 90 000 m³ debris‐flow event triggered by a rapid regressive landslide with high water content. Field evidence revealed a maximum flow depth of 7–8 m, with an estimated peak discharge of 350–400 m³ s^?1. Depositional evidence and grain‐size distribution of the debris pose the debris flow in an intermediate condition between the fluid‐mud and grain‐flow behaviour. The debris‐flow material has silt–clay content up to 15 per cent. The rheological behaviour of the finer matrix was directly assessed with the ball measuring system. The measurements, performed on two samples at 45–63 per cent in sediment concentration by volume, gave values of 3·5–577 Pa for the yield strength, and 0·6–27·9 Pa s for the viscosity. Based on field evidence, we have empirically estimated the yield strength and viscosity ranging between 4000 ± 200 Pa, and 108–134 Pa s, respectively. We used the Flo‐2D code to replicate the debris‐flow event. We applied the model with rheological properties estimated by means of direct measurements and back‐analyses. The results of these models show that the rheological behaviour of a debris‐flow mass containing coarse clasts can not be assessed solely on the contribution of the finer matrix and thus neglecting the effects of direct grain contacts. For debris flows composed by a significant number of coarse clasts a back‐analysis estimation of the rheological parameters is necessary to replicate satisfactorily the depositional extent of debris flows. In these cases, the back‐estimated coefficients do not adequately describe the rheological properties of the debris flow. Copyright © 2006 John Wiley & Sons, Ltd.     

Experimental analysis on the impact force of viscous debris flow

A miniaturized flume experiment was carried out to measure impact forces of viscous debris flow. The flow depth (7.2–11.2 cm), velocity (2.4–5.2 m/s) and impact force were recorded during the experiment. The impact process of debris flow can be divided into three phases by analyzing the variation of impact signals and flow regime. The three phases are the sudden strong impact of the debris flow head, continuous dynamic pressure of the body and slight static pressure of the tail. The variation of impact process is consistent with the change in the flow regime. The head has strong–rapid impact pressure, which is shown as a turbulent‐type flow; the body approximates to steady laminar flow. Accordingly, the process of debris flows hitting structures was simplified to a triangle shape, ignoring the pressure of the tail. In order to study the distribution of the debris flow impact force at different depths and variation of the impact process over time, the impact signals of slurry and coarse particles were separated from the original signals using wavelet analysis. The slurry's dynamic pressure signal appears to be a smooth curve, and the peak pressure is 12–34 kPa when the debris flow head hits the sensors, which is about 1.54 ± 0.36 times the continuous dynamic pressure of the debris flow body. The limit of application of the empirical parameter α in the hydraulic formula was also noted. We introduced the power function relationship of α and the Froude number of debris flows, and proposed a universal model for calculating dynamic pressure. The impact pressure of large particles has the characteristic of randomness. The mean frequency of large particles impacting the sensor is 210 ± 50–287 ± 29 times per second, and it is 336 ± 114–490 ± 69 times per second for the debris flow head, which is greater than that in the debris flow body. Peak impact pressure of particles at different flow depths is 40–160 kPa, which is 3.2 ± 1.5 times the impact pressure of the slurry at the bottom of the flow, 3.1 ± 0.9 times the flow in the middle, and 3.3 ± 0.9 times the flow at the surface. The differences in impact frequency indicate that most of the large particles concentrate in the debris flow head, and the number of particles in the debris flow head increases with height. This research supports the study of solid–liquid two phase flow mechanisms, and helps engineering design and risk assessment in debris flow prone areas. Copyright © 2015 John Wiley & Sons, Ltd.     

Hydraulic,physical and rheological characteristics of rain‐triggered lahars at Semeru volcano,Indonesia

Lahars (volcanic debris flows) have been responsible for 40% of all volcanic fatalities over the past century. Mount Semeru (East Java, Indonesia) is a persistently active composite volcano that threatens approximately one million people with its lahars and pyroclastic flows. Despite their regularity, the behaviour and the propagation of these rain‐triggered lahars are poorly understood. In situ samples were taken from lahars in motion at two sites in the Curah Lengkong River, on the southeast flank of Semeru, providing estimates of the particle concentration, grain size spectrum, grain density and composition. This enables us to identify flow sediment from three categories of lahars: (a) hyperconcentrated flow, (b) non‐cohesive, clast‐ and matrix‐supported debris flow, and (c) muddy flood. To understand hyperconcentrated flow sediment transport processes, it is more appropriate to sample the active flows than the post‐event lahar deposits because in situ sampling retains the full spectrum of the grain‐size distribution. Rheometrical tests on materials sampled from moving hyperconcentrated flows were carried out using a laboratory vane rheometer. Despite technical difficulties, results obtained on the <63, <180, and <400 µm fractions of the sampled sediment, suggest a purely frictional behaviour. Importantly, and contrary to previous experiments conducted with monodisperse suspensions, our results do not show any transition towards a viscous behaviour for high shear rates. These data provide important constraints for future physical and numerical modelling of lahar flows. Copyright © 2010 John Wiley & Sons, Ltd.     

A depth‐averaged two‐phase model for debris flows over erodible beds

Mass exchange between debris flow and the bed plays a vital role in debris flow dynamics. Here a depth‐averaged two‐phase model is proposed for debris flows over erodible beds. Compared to previous depth‐averaged two‐phase models, the present model features a physical step forward by explicitly incorporating the mass exchange between the flow and the bed. A widely used closure model in fluvial hydraulics is employed to estimate the mass exchange between the debris flow and the bed, and an existing relationship for bed entrainment rate is introduced for comparison. Also, two distinct closure models for the bed shear stresses are evaluated. One uses the Coulomb friction law and Manning's equation to determine the solid and fluid resistances respectively, while the other employs an analytically derived formula for the solid phase and the mixing length approach for the fluid phase. A well‐balanced numerical algorithm is applied to solve the governing equations of the model. The present model is first shown to reproduce average sediment concentrations in steady and uniform debris flows over saturated bed as compared to an existing formula underpinned by experimental datasets. Then, it is demonstrated to perform rather well as compared to the full set of USGS large‐scale experimental debris flows over erodible beds, in producing debris flow depth, front location and bed deformation. The effects of initial conditions on debris flow mass and momentum gain are resolved by the present model, which explicitly demonstrates the roles of the wetness, porosity and volume of bed sediments in affecting the flow. By virtue of extended modeling cases, the present model produces debris flow efficiency that, as revealed by existing observations and empirical relations, increases with initial volume, which is enhanced by mass gain from the bed. Copyright © 2017 John Wiley & Sons, Ltd.     

Distorted Froude‐scaled flume analysis of large woody debris

This paper presents the results of a movable‐boundary, distorted, Froude‐scaled hydraulic model based on Abiaca Creek, a sand‐bedded channel in northern Mississippi. The model was used to examine the geomorphic and hydraulic impact of simplified large woody debris (LWD) elements. The theory of physical scale models is discussed and the method used to construct the LWD test channel is developed. The channel model had bed and banks moulded from 0·8 mm sand, and flow conditions were just below the threshold of motion so that any sediment transport and channel adjustment were the result of the debris element. Dimensions and positions of LWD elements were determined using a debris jam classification model. Elements were attached to a dynamometer to measure element drag forces, and channel adjustment was determined through detailed topographic surveys. The fluid drag force on the elements decreased asymptotically over time as the channel boundary eroded around the elements due to locally increased boundary shear stress. Total time for geomorphic adjustment computed for the prototype channel at the Q₂ discharge (discharge occurring once every two years on average) was as short as 45 hours. The size, depth and position of scour holes, bank erosion and bars created by flow acceleration past the elements were found to be related to element length and position within the channel cross‐section. Morphologies created by each debris element in the model channel were comparable with similar jams observed in the prototype channel. Published in 2001 John Wiley & Sons, Ltd.     

The triggering of debris flow due to channel‐bed failure in some alpine headwater basins of the Dolomites: analyses of critical runoff

The debris deposits at the bottom of very steep natural channels and streams in high mountain areas can be mobilized by runoff, triggering a water–sediment mixture flow known as debris flow. The routing of debris flow through human settlements can cause damage to civil structures and loss of human lives. The prediction of such an event, or the runoff discharge that triggers it, assumes an interest in risk analyses and the planning of defence measures. The object of this study is to find a method to determine the critical runoff value that triggers debris flow as a result of channel‐bed failure. Historical and rainfall data on 30 debris flows that occurred in six watersheds of the Dolomites (north‐eastern Italian Alps) were collected from different sources. Field investigations at the six sites, together with the hydrologic response to the rainfalls that triggered the events, were performed to obtain a realistic scenario of the formation of the debris flow there occurred. Field observations include a survey along the channel of the triggering reach of debris flow, with measurements of the channel slope and cross‐section and sampling of debris deposits for grain size distribution. Simulated runoff discharge values based on the rainfall recorded by pluviometers were then compared with values obtained through experimental criteria on the initiation and formation of debris flow by bed failure. The results are discussed to provide a plausible physical‐based method for the prediction of the triggering of debris flow by channel‐bed failure. Copyright © 2007 John Wiley & Sons, Ltd.     

泥石流区桥墩损毁机制与控制研究

为了保证安全,泥石流多发区的道路常采用桥梁的方式通过。位于泥石流区的桥梁的桥墩在泥石流暴发时受到泥石流的冲击,常会造成不同程度的损毁。泥石流冲击力是泥石流区桥墩受到的主要荷载,目前在计算泥石流冲击力时一般将其视为均质体,但是泥石流为固液两相流体,因此得到的计算结果误差较大。为了提高精确度,本文对泥石流冲击力计算公式进行了修正,先分别运用动力学中的弹性碰撞理论和牛顿第二定律对泥石流固相和液相的冲击力进行计算,然后将其进行叠加,得到总的泥石流冲击力。泥石流区桥墩破坏的模式主要有冲击破坏、倾覆破坏和滑动破坏3种形式。为了减小泥石流对桥墩的破坏能,可在桥墩受到泥石流冲击的部位设置消能层,通过算例发现,设置消能层后冲击力减小了26.94%。     

Real‐time monitoring and estimation of the discharge of flash floods in a steep mountain catchment

Synchronously and accurately estimating the flood discharges and dynamic changes in the fluid density is essential for hydraulic analysis and forecasting of flash floods, as well as for risk assessment. However, such information is rare for steep mountain catchments, especially in regions that are hotspots for earthquakes. Therefore, six hydrological monitoring sites were established in the main stream and tributaries of the 78.3‐km² Longxi River catchment, an affected region of the Wenchuan earthquake region in China. Direct real‐time monitoring equipment was installed to measure the flow depths, velocities, and fluid total pressures of the flood hydrographs. On the basis of field measurements, real‐time mean cross‐sectional velocities during the flood hydrographs could be derived from easily obtainable parameters: cross‐sectional maximum velocities and the calibrated dimensionless parameter K_h . Real‐time discharges were determined on the basis of a noncontact method to establish the effective rating curves of this mountainous stream, ranging from 1.46 to 386.34 m³/s with the root mean square errors of ≤10.22 m³/s. Compared with the traditional point‐velocity method and empirical Manning's formula, the proposed noncontact method was reliable and safe for monitoring whole flood hydrographs. Additionally, the real‐time fluid density during the flood hydrographs was calculated on the basis of the direct monitoring parameters for fluid total pressures and water depths. During the flood hydrograph, transient flow behaviour with higher fluid density generally occurred downstream during the flood peak periods when the flow was in the supercritical flow regime. The observed behaviour greatly increased the threat of damage to infrastructure and human life near the river. Thus, it is important to accurately estimate flood discharge and identify for fluid densities so that people at risk from an impending flash flood are given reliable, advanced warning.     

Dendrogeomorphic reconstruction of past debris‐flow activity using injured broad‐leaved trees

Tree‐ring records from conifers have been regularly used over the last few decades to date debris‐flow events. The reconstruction of past debris‐flow activity was, in contrast, only very rarely based on growth anomalies in broad‐leaved trees. Consequently, this study aimed at dating the occurrence of former debris flows from growth series of broad‐leaved trees and at determining their suitability for dendrogeomorphic research. Results were obtained from gray alder (Alnus incana (L.) Moench), silver birch and pubescent birch (Betula pendula Roth and Betula pubescens Ehrh.), aspen (Populus tremula L.), white poplar, black poplar and gray poplar (Populus alba L., Populus nigra L. and Populus x canescens (Ait.) Sm.), goat willow (Salix caprea L.) and black elder (Sambucus nigra L.) injured by debris‐flow activity at Illgraben (Valais, Swiss Alps). Tree‐ring analysis of 104 increment cores, 118 wedges and 93 cross‐sections from 154 injured broad‐leaved trees allowed the reconstruction of 14 debris‐flow events between AD 1965 and 2007. These events were compared with archival records on debris‐flow activity at Illgraben. It appears that debris flows are very common at Illgraben, but only very rarely left the channel over the period AD 1965–2007. Furthermore, analysis of the spatial distribution of disturbed trees contributed to the identification of six patterns of debris‐flow routing and led to the determination of preferential breakout locations of events. The results of this study demonstrate the high potential of broad‐leaved trees for dendrogeomorphic research and for the assessment of the travel distance and lateral spread of debris‐flow surges. Copyright © 2010 John Wiley & Sons, Ltd.     

GIS‐assisted modelling for debris flow hazard assessment based on the events of May 1998 in the area of Sarno,Southern Italy: II. Velocity and dynamic pressure

The velocity and dynamic pressure of debris flows are critical determinants of the impact of these natural phenomena on infrastructure. Therefore, the prediction of these parameters is critical for hazard assessment and vulnerability analysis. We present here an approach to predict the velocity of debris flows on the basis of the energy line concept. First, we obtained empirically and field‐based estimates of debris flow peak discharge, mean velocity at peak discharge and velocity, at channel bends and within the fans of ten of the debris flow events that occurred in May 1998 in the area of Sarno, Southern Italy. We used this data to calibrate regression models that enable the prediction of velocity as a function of the vertical distance between the energy line and the surface. Despite the complexity in morphology and behaviour of these flows, the statistical fits were good and the debris flow velocities can be predicted with an associated uncertainty of less than 30% and less than 3 m s^?1. We wrote code in Visual Basic for Applications (VBA) that runs within ArcGIS^® to implement the results of these calibrations and enable the automatic production of velocity and dynamic pressure maps. The collected data and resulting empirical models constitute a realistic basis for more complex numerical modelling. In addition, the GIS implementation constitutes a useful decision‐support tool for real‐time hazard mitigation. Copyright © 2008 John Wiley & Sons, Ltd.     

Morphology and sedimentology of a complex debris flow in a clay‐shale basin

Coupling morphological, sedimentological, and rheological studies to numerical simulations is of primary interest in defining debris‐flow hazard on alluvial fans. In particular, numerical runout models must be carefully calibrated by morphological observations. This is particularly true in clay‐shale basins where hillslopes can provide a large quantity of poorly sorted solid materials to the torrent, and thus change both the mechanics of the debris flow and its runout distance. In this context, a study has been completed on the Faucon stream (southeastern French Alps), with the objectives of (1) defining morphological and sedimentological characteristics of torrential watersheds located in clay‐shales, and (2) evaluating through a case study the scouring potential of debris flows affecting a clay‐shale basin. Morphological surveys, grain‐size distributions and petrographic analyses of the debris‐flow deposits demonstrate the granular character of the flow during the first hectometre, and its muddy character from there to its terminus on the debris fan. These observations and laboratory tests suggest that the contributing areas along the channel have supplied the bulk of the flow material. Copyright © 2005 John Wiley & Sons, Ltd.     

Modelling a cohesive‐frictional debris flow: an experimental,theoretical, and field‐based study

The rheology of debris flows is difficult to characterize owing to the varied composition and to the uneven distribution of the components that may range from clay to large boulders, in addition to water. Few studies have addressed debris flow rheology from observational, experimental, and theoretical viewpoints in conjunction. We present a coupled rheological‐numerical model to characterize the debris flows in which cohesive and frictional materials are both present. As a first step, we consider small‐scale artificial debris flows in a flume with variable percentages of clay versus sand, and measure separately the rheological properties of sand–clay mixtures. A comparison with the predictions of a modified version of the numerical model BING shows a reasonable agreement between measurements and simulations. As application to a field case, we analyse a recent debris flow that occurred in Fjærland (Western Norway) for which much information is now available. The event was caused by a glacial lake outburst flood (GLOF) originating from the failure of a moraine ridge. In a previous contribution (Breien et al., Landslides, 2008 , 5: 271–280) we focused on the hydrological and geomorphological aspects. In particular we documented the marked erosion and reported the change in sediment transport during the event. In contrast to the laboratory debris flows, the presence of large boulders and the higher normal pressure inside the natural debris flow requires the introduction of a novel rheological model that distinguishes between mud‐to–clast supported material. We present simulations with a modified BING model with the new cohesive‐frictional rheology. To account for the severe erosion operated by the debris flow on the colluvial deposits of Fjærland, we also suggest a simple model for erosion and bulking along the slope path. Numerical simulations suggest that a self‐sustaining mechanism could partly explain the extreme growth of debris flows running on a soft terrain.     

Study on hydraulic characteristics of sabo dam with a flap structure for debris flow

The front part of the flow is very important and complex in the case of debris flow where there is an accumulation of large boulders. It is important to control or dampen the energy of the frontal part of a debris flow for the safety of the downstream area because the impact pressure of debris flow is much greater than that of clear fluid. The main objective of this study is to analyze the hydraulic characteristics of the proposed dam (i.e. closed-type dam with flap). The vertical pressure distribution of this type is compared with conventional dam types. In the experiments, the total pressure associated with major debris flows was recorded in real time by a system consisting of four dynamic pressure sensors installed on different types of dam. The results from experimental data clearly show that the dam with the flap has advantages of capturing the debris flow with large boulders and controls the total pressure by flow circulation due to presence of the flap structure compared to a closed-type dam without flap. Further-more, the empirical coefficients of hydrodynamic and solid collision models were proposed and com-pared with available coefficients.     

Tree‐age control on reconstructed debris‐flow frequencies: examples from a regional dendrogeomorphic reconstruction in the Crimean Mountains

The Crimean Mountains (Ukraine) are renowned for the highest occurrence of debris flows along the northern coast of the Black Sea, but information on their origin, frequency and triggers is widely lacking. This study reconstructs a regional time series of debris flows in eight catchments located on the slopes above Yalta. Dendrogeomorphic analyses were performed on 1122 increment cores selected from 566 black pines (Pinus nigra ssp. pallasiana) with clear signs of external damage induced by past debris‐flow activity. The trees sampled were divided into old and young trees. The sample contains 361 young trees with post‐1930 innermost rings and 205 old trees with pre‐1930 germination dates. The two groups of trees were analyzed separately to identify possible age effects in the reconstructed debris‐flow series and to assess the ability of P. nigra to record geomorphic disturbances over time. We date a total of 215 debris flows back to ad 1701 and observe a mean decadal frequency of 6.9 events, with a peak in activity during the 1940s (20 events). The young trees record an increase in debris‐flow activity over the last 70 years, whereas the frequency of events remained fairly constant in the old trees for the same period. By contrast, the formation of reaction wood became increasingly scarce with increasing tree age whereas the occurrence of abrupt growth suppression increased. Copyright © 2014 John Wiley & Sons, Ltd.     

Full waveform inversion of SH‐ and Love‐wave data in near‐surface prospecting

We develop a two‐dimensional full waveform inversion approach for the simultaneous determination of S‐wave velocity and density models from SH ‐ and Love‐wave data. We illustrate the advantages of the SH/Love full waveform inversion with a simple synthetic example and demonstrate the method's applicability to a near‐surface dataset, recorded in the village ?achtice in Northwestern Slovakia. Goal of the survey was to map remains of historical building foundations in a highly heterogeneous subsurface. The seismic survey comprises two parallel SH‐profiles with maximum offsets of 24 m and covers a frequency range from 5 Hz to 80 Hz with high signal‐to‐noise ratio well suited for full waveform inversion. Using the Wiechert–Herglotz method, we determined a one‐dimensional gradient velocity model as a starting model for full waveform inversion. The two‐dimensional waveform inversion approach uses the global correlation norm as objective function in combination with a sequential inversion of low‐pass filtered field data. This mitigates the non‐linearity of the multi‐parameter inverse problem. Test computations show that the influence of visco‐elastic effects on the waveform inversion result is rather small. Further tests using a mono‐parameter shear modulus inversion reveal that the inversion of the density model has no significant impact on the final data fit. The final full waveform inversion S‐wave velocity and density models show a prominent low‐velocity weathering layer. Below this layer, the subsurface is highly heterogeneous. Minimum anomaly sizes correspond to approximately half of the dominant Love‐wavelength. The results demonstrate the ability of two‐dimensional SH waveform inversion to image shallow small‐scale soil structure. However, they do not show any evidence of foundation walls.     

带弹簧支撑的新型泥石流拦挡坝抗冲击性能研究

为了解决普通重力式泥石流拦挡坝在大规模泥石流发生时容易被大块石损毁的问题,提出带弹簧支撑的新型泥石流拦挡坝,并采用钢球代替泥石流中的大块石,运用有限元软件ANSYS/LS-DYNA对这种新型坝体进行泥石流大块石的冲击模拟,从坝体的变形、支反力、Von Mises应力、加速度和应变率5个方面与普通重力式拦挡坝进行对比分析。结果表明：与普通泥石流拦挡坝相比,带弹簧支撑的新型泥石流拦挡坝的支反力可减小3/4左右,钢球的冲击加速度可降到1/3.87,坝体的响应加速度可降到1/2.61,说明带弹簧支撑的新型泥石流拦挡坝具有非常好的抗冲击性能。     

Geomorphological characteristics of small debris flows on Junior's Kop,Marion Island,maritime sub ‐ Antarctic

The geomorphological characteristics of small debris flows in a maritime sub‐Antarctic environment are described. The morphological and sedimentological characteristics of the debris flows are comparable to debris flows documented for other parts of the world; their initiation appears closely linked to the unusual environment in which they are found. Sediment supply is generated by diurnal frost heave of loamy sediment associated with Azorella selago. The debris flows are triggered by sediment mobilization upon saturation of the frost‐heaved surface gravel and overland flow over the low‐permeability and frost‐susceptible slope materials. Morphological effects of the flows are short‐lived due to obliteration by subsequent frost heave activity. Copyright © 2000 John Wiley & Sons, Ltd.