The significance of rock structure,lithology and pre‐glacial deep weathering for the shape of intermediate‐scale glacial erosional landforms

The main landforms within the glacially scoured Precambrian rocks of the Swedish west coast are closely connected to the principal structural pattern and have lately been explained as mainly a result of etch processes, probably during the Mesozoic and with a possible second period of etching during the Neogene. To explore the effect of multiple glacial erosion on the rock surfaces, an island with two different lithologies and with striae from different directions was selected for a detailed study, focusing on the shape of roches moutonnées. Air‐photo interpretation of bedrock lineaments and roches moutonnées combined with detailed field mapping and striae measurements are used to interpret the structural and lithological control on the resulting shape. The study reveals a significant difference in shape between roches moutonnées in augen‐granite and orthogneiss. Low elongated and streamlined roches moutonnées occur in the gneiss area, striated by a Late Weichselian ice flow from the NE. This ice flow is subparallel with both the local dominant trend of topographically well‐expressed joints and the schistosity of the gneiss. Frequently, there are no signs of quarrying on the lee‐sides of the gneiss roches moutonnées and hence they resemble the shape of whalebacks, or ruwares, as typically associated with the exposed basal weathering surface found in tropical areas. The granite roches moutonnées were formed by an older ice flow from the ESE, which closely followed the etched WNW–ESE joint system of the granite. Late Weichselian ice flow from the NE caused only minor changes of the landforms. On the contrary, marks of the early ESE ice flow are poorly preserved in the gneiss area, where it probably never had any large effect as the flow was perpendicular to both schistosity and structures and, accordingly, also to the pre‐glacial relief. The study demonstrates that coincidence between ice flow direction and pre‐glacially etched structures is most likely to determine the effects of glacial erosion. Copyright © 2002 John Wiley & Sons, Ltd.     

Large ice‐contact slope movements: glacial buttressing,deformation and erosion

Glaciers and slope movements may act simultaneously to erode and modify glaciated slopes. Undercutting by glaciers can destabilize slopes but the extent to which slope failure may progress prior to subsequent glacier withdrawal has not hitherto been considered. The traditional view has been that the buttressing effect of ice prevents slope movement. The problem with this view is that ice is one‐third the density of rock and flows under low applied stress. Consequently, failed slopes may move into the glacier if they exert a stress in excess of the resistance provided by the glacier. Slope movement rate depends on ice rheology and other factors influencing driving and resisting stresses. Simple viscous equations are used to investigate these variables. The equations predict that small (<125 000 m³) ice‐contact rockslides can deform ice at several mm/year, increasing to several m/year for very large (>10⁸ m³) rockslides. To test these estimates, field evidence is presented of slope movements in glaciated valleys of New Zealand; narrowing or squeezing of glaciers adjacent to unstable rock slopes is demonstrated and considered to be the result of slope movement. For one site, geomorphic mapping and slope movement monitoring data show that movement rates are of similar order of magnitude to those predicted by the viscous equations; closer agreement could be achieved with the application of modelling techniques that can more realistically model the complex slope geometries and stability factors encountered, or by obtaining additional empirical data to calibrate the models. This research implies that, while the concept of glacial debuttressing – the reduction of slope support from withdrawal of glaciers – is valid, complete debuttressing is not a prerequisite for the movement of ice‐contact rock slopes. These slope movements may contribute to the erosional processes of glaciers and the evolution of glaciated slopes in a previously unrecognized way. Copyright © 2012 John Wiley & Sons, Ltd.     

Athabasca Glacier,Canada – a field example of subglacial ice and till erosion?

The Athabasca Glacier, resting on a rigid bed, provides an excellent example of subglacial ice and till erosion. The presence of a thin mobile till layer is shown by the presence of flutes, saturated till layer, push moraines and ploughed boulders. Cross‐cutting striations, v‐shaped striations and reversed stoss‐and‐lee clasts are indicative of clasts rotating within this layer. As the till moves it erodes the bedrock and clasts within it. A combination of erosion by ice and till produces stoss‐and‐lee‐clasts and generates striations on flutes and embedded clasts, as well as eroding the bedrock into a continuum of smoothed, rounded and streamlined forms. Copyright © 2005 John Wiley & Sons, Ltd.     

Snow cornice dynamics as a control on plateau edge erosion in central Svalbard

Snow cornices grow extensively on leeward edges of plateau mountains in central Svalbard. A dominant wind direction, a snowdrift source area and a sharp slope transition largely control the formation of snow cornices in a barren peri‐glacial landscape. Seasonal snow cornice dynamics control bedrock weathering and erosion in sedimentary bedrock on the Gruvefjellet plateau edge in the valley Longyeardalen. Air, snow and ground temperature sensors, as well as automatic time‐lapse cameras on a leeward facing plateau edge were used to study seasonal cornice dynamics. These techniques allowed for monitoring of cornice accretion, deformation and collapse/melting in great detail. The active layer of the top plateau edge is characterized by high moisture content due to rain before freeze‐up in autumn and cornice meltdown during spring thaw. Thus frost weathering there can be very efficient in this otherwise cold and dry environment. Within the first autumn snowstorms, a vertical fully developed cornice was in place (190 cm thick). The backwall surface beneath the thickest part of the cornice remained in the ice segregation ‘frost cracking window’ for almost nine months. Highly weathered rock material from the plateau edge is thus incorporated into the cornice during cornice accretion. Brittle snow deformation leads to the opening of cornice tension cracks between the cornice mass and the snowpack on the plateau. These cracks are a prerequisite for cornice collapses, and often trigger cornice fall avalanches on the slope beneath. In these open cornice tension cracks, weathered rock debris, plucked from the plateau edge, can be visible, demonstrating the erosional property of the cornices. The cornice will either collapse or melt, resulting in suspended sediment transport downslope by cornice fall avalanche or release as rock fall respectively. Therefore, cornices both promote and trigger high weathering rates on Gruvefjellet, and thus control presently the development of the rockwall free faces and the talus cones. Copyright © 2012 John Wiley & Sons, Ltd.     

Using UAV acquired photography and structure from motion techniques for studying glacier landforms: application to the glacial flutes at Isfallsglaciären

Glacier and ice sheet retreat exposes freshly deglaciated terrain which often contains small‐scale fragile geomorphological features which could provide insight into subglacial or submarginal processes. Subaerial exposure results in potentially rapid landscape modification or even disappearance of the minor‐relief landforms as wind, weather, water and vegetation impact on the newly exposed surface. Ongoing retreat of many ice masses means there is a growing opportunity to obtain high resolution geospatial data from glacier forelands to aid in the understanding of recent subglacial and submarginal processes. Here we used an unmanned aerial vehicle to capture close‐range aerial photography of the foreland of Isfallsglaciären, a small polythermal glacier situated in Swedish Lapland. An orthophoto and a digital elevation model with ~2 cm horizontal resolution were created from this photography using structure from motion software. These geospatial data was used to create a geomorphological map of the foreland, documenting moraines, fans, channels and flutes. The unprecedented resolution of the data enabled us to derive morphological metrics (length, width and relief) of the smallest flutes, which is not possible with other data products normally used for glacial landform metrics mapping. The map and flute metrics compare well with previous studies, highlighting the potential of this technique for rapidly documenting glacier foreland geomorphology at an unprecedented scale and resolution. The vast majority of flutes were found to have an associated stoss‐side boulder, with the remainder having a likely explanation for boulder absence (burial or erosion). Furthermore, the size of this boulder was found to strongly correlate with the width and relief of the lee‐side flute. This is consistent with the lee‐side cavity infill model of flute formation. Whether this model is applicable to all flutes, or multiple mechanisms are required, awaits further study. © 2016 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd.     

Suspended sediment and total dissolved solid yield patterns at the headwaters of Urumqi River,northwestern China: a comparison between glacial and non‐glacial catchments

In order to understand the differences in the suspended sediment and total dissolved solid (TDS) yield patterns between the glacial and non‐glacial catchments at the headwaters of Urumqi River, northwestern China, water samples were collected from a glacier catchment and an empty cirque catchment within the region, during three melting seasons from 2006 to 2008. These samples were analyzed to estimate suspended sediment and TDS concentrations, fluxes and erosion rates in the two adjoining catchments. There were remarked differences in suspended sediment and TDS yield patterns between the two catchments. Suspended sediment concentrations were controlled mainly by the sediment source, whereas TDS concentrations were primarily related to the hydrologic interaction with soil minerals. Generally, the glacial catchment had much higher suspended sediment and TDS yields, together with higher denudation rates, than the non‐glacial catchment. Overall, glacial catchment was mainly dominated by physical denudation process, whereas the non‐glacial catchment was jointly influenced by physical and chemical denudation processes. The observed differences in material delivery patterns were mainly controlled by the runoff source and the glacial processes. The melting periods of glacier and snow were typically the most important time for the suspended sediment and TDS yields. Meanwhile, episodic precipitation events could generate disproportionately large yields. Subglacial hydrology dynamics, glaciers pluck and grind processes could affect erodibility, and the large quantities of dust stored on the glacier surface provided additional sources for suspended sediment transport in the glacial catchment. These mechanisms imply that, in response to climate change, the catchment behaviour will be modified significantly in this region, in terms of material flux. Copyright © 2013 John Wiley & Sons, Ltd.     

Hydro‐meteorological drivers and sources of suspended sediment flux in the pro‐glacial zone of the retreating Castle Creek Glacier,Cariboo Mountains,British Columbia,Canada

Glaciers are major agents of erosion that increase sediment load to the downstream fluvial system. The Castle Creek Glacier, British Columbia, Canada, has retreated ~1.0 km in the past 70 years. Suspended sediment concentration (SSC) and streamflow (Q) were monitored independently at five sites within its pro‐glacial zone over a 60 day period from July to September 2011, representing part of the ablation season. Meteorological data were collected from two automatic weather stations proximal to the glacier. The time‐series were divided into hydrologic days and the shape and magnitude of the SSC response to hydro‐meteorological conditions (‘cold and wet’, ‘hot and dry’, ‘warm and damp’, and ‘storm’) were categorized using principal component analysis (PCA) and cluster analysis (CA). Suspended sediment load (SSL) was computed and summarized for the categories. The distribution of monitoring sites and results of the multivariate statistical analyses describe the temporal and spatial variability of suspended sediment flux and the relative importance of glacial and para‐glacial sediment sources in the pro‐glacial zone. During the 2011 study period, ~ 60% of the total SSL was derived from the glacial stream and sediment deposits proximal to the terminus of the glacier; during ‘storm’ events, that contribution dropped to ~40% as the contribution from diffuse and point sources of sediment throughout the pro‐glacial zone and within the meltwater channels increased. While ‘storm’ events accounted for just 3% of the study period, SSL was ~600% higher than the average over the monitoring period, and ~20% of the total SSL was generated in that time. Determining how hydro‐meteorological conditions and sediment sources control sediment fluxes will assist attempts to predict how pro‐glacial zones respond to future climate changes. Copyright © 2015 John Wiley & Sons, Ltd.     

The bubble bursts for cavitation in natural rivers: laboratory experiments reveal minor role in bedrock erosion

The erosion of rock‐bedded channels generally is considered a slow process caused mainly by abrasion due to bedload or suspended sediments, but the mechanisms of rapid erosion remain unclear. Cavitation is a clear‐fluid erosive process, well known for its effect on engineering structures, when water vapour bubbles collapse and the resultant pressure shocks erode the boundary. However, although the occurrence of cavitation erosion in natural watercourses has long been a matter of debate, as yet there are no incontrovertible examples of cavitation damage to natural river beds. Using flume experiments, we show for the first time that only weakly‐cavitating clear‐water flows can occur for the range of flow velocities observed in rivers, and these do not erode medium‐hardness rocks after 68 hours. During this time period, only a very soft rock featured erosional marks due to dissolution. Thus, our results cast significant doubt on the likelihood of identifying cavitation damage in most rivers, and provide pointers to those river systems that might be investigated further to identify cavitation erosion. Copyright © 2016 John Wiley & Sons, Ltd.     

Hydrological and erosional response to natural rainfall in a semi‐arid area of south‐east Spain

A better knowledge of soil erosion by water is essential for planning effective soil and water conservation practices in semi‐arid Mediterranean environments. The special climatic and hydrological characteristics of these areas, however, make accurate soil loss predictions difficult, particularly in the absence of minimal data. Two zero‐order experimental microcatchments (328–759 m²), representative of an extensive semi‐arid watershed with a high potential erosion risk in the south‐east of Spain, were selected and monitored for 3 years (1991–93) in order to provide information on the hydrological and erosional response. A pluviogram and hydrograph recorded data at 1‐min intervals during each storm, after which the soil loss was collected and the particle size of the sediment was analysed. Runoff coefficients of about 9% and soil losses of between 84·83 and 298·9 g m^?2 year^?1 were observed in the area. Rapid response times (geometric mean values lower than 2 h) and low runoff thresholds (mean values between 3·5 to 5·9 mm) were the norm in the experimental areas. A rain intensity of over 15 mm h^?1 was considered as ‘erosive rainfall’ in these areas because of the total soil loss and the transport capacity of the overland flow. Differences in pore‐size distribution explained the different hydrological responses observed between areas. The erosional response was more complex and basically seemed to be determined by soil aggregate stability and topographical properties. A greater proportion of finer particles in the eroded material than in the soil matrix indicated selective erosion and the transport of finer material. Copyright © 2001 John Wiley & Sons, Ltd.     

Western Pacific in glacial cycles:Seasonality in marginal seas and variabilities of Warm Pool

A serics of low-latitude marginal seas, ranging from the southern South China Sea in the north to the Arafura Sea in the south, are located within the Western Pacific Warm Pool. As shown by rnicropaleontological, isotopical and organic geochemical analyses, the sea surface temperatures in the marginal seas at the last glacial maximum were much cooler than those in the open Western Pacific Ocean. The emergence of extensive shelves of the marginal seas at the glacial low sea-level stand and the decrease of surface temperatures in their deeper water parts resulted in a remarkable reduction of the ability of vapor and heat transport to the atmosphere, causing variabilities to the Warm Pool in the glacial cycles. The intensification of winter monsoon at the glacial stages not only led to a decrease of the surface water temperature and hence to an enhanced seasonality, but also carried moisture from the sea to the tropical islands, giving rise to the downward shift of snowline and mountainous vegetation zones there. It may offer a new alternative in solution of the “Tropical Ocean Paleo-temperature Enigma”. Project supported by the National Natural Science Foundation of China (Grant No. 49576286).     

Lateral bedrock erosion and valley formation in a heterogeneously layered landscape,Northeast Kansas

In this study, we present direct field measurements of modern lateral and vertical bedrock erosion during a 2-year study period, and optically stimulated luminescence (OSL) ages of fluvial material capping a flat bedrock surface at Kings Creek located in northeast Kansas, USA. These data provide insight into rates and mechanisms of bedrock erosion and valley-widening in a heterogeneously layered limestone-shale landscape. Lateral bedrock erosion outpaced vertical incision during our 2-year study period. Modern erosion rates, measured at erosion pins in limestone and shale bedrock reveal that shale erosion rate is a function of wetting and drying cycles, while limestone erosion rate is controlled by discharge and fracture spacing. Variability in fracture spacing amongst field sites controls the size of limestone block collapse into the stream, which either allowed continued lateral erosion following rapid detachment and transport of limestone blocks, or inhibited lateral erosion due to limestone blocks that protected the valley wall from further erosion. The OSL ages of fluvial material sourced from the strath terrace were older than any material previously dated at our study site and indicate that Kings Creek was actively aggrading and incising throughout the late Pleistocene. Coupling field measurements and observations with ages of fluvial terraces can be useful to investigate the timing and processes linked to how bedrock rivers erode laterally over time to form wide bedrock valleys.     

Suspended sediment and phosphorus in proglacial rivers: bioavailability and potential impacts upon the P status of ice‐marginal receiving waters

This paper adopts standard tests developed in temperate catchment research to determine the total phosphorus (TP) and the algal available (base‐extractable) phosphorus (NaOH–P) content of a wide range of glaciofluvial sediments from the Northern Hemisphere. We find that the TP content of these sediments is broadly similar to the P content of major rock types in Earth's crust (230–670 µgP/g) and so the TP yields of glacier basins may be high owing to the efficacy of suspended sediment evacuation by glacial meltwaters. We show that this is best achieved where subglacial drainage systems are present. The NaOH–P pool of the sediments is found to be low (1–23 µgP/g) relative to the TP pool and also to the NaOH–P pool of suspended sediments in temperate, non‐glacierized catchments. This most probably reflects the restricted duration of intimate contact between dilute meltwaters and glacial suspended sediments during the ablation season. Thus, despite the high surface‐area:volume ratio of glacial suspended sediments, the potential for P adsorption to mineral surfaces following release by dissolution is also low. Further, sorption experiments and sequential extraction tests conducted using glacial suspended sediments from two Svalbard catchments indicate that the generation of reactive secondary minerals (e.g. Fe‐ and other hydroxides) with a strong capacity to scavenge P from solution (and thereby promote the continued dissolution of P) may also be limited by the short residence times. Most P is therefore associated with poorly weathered, calcite/apatite‐rich mineral phases. However, we use examples from the Svalbard glacier basins (Austre Brøggerbreen and Midre Lovénbreen) to show that the high sediment yields of glaciers may result in appreciable NaOH–P loading of ice‐marginal receiving waters. Again, the importance of subglacial drainage is highlighted, as it produces a major, episodic release of NaOH–P at Midre Lovénbreen that results in a yield (8·2 kg NaOH–P/km²/year) more than one order of magnitude greater than that at Austre Brøggerbreen (where subglacial drainage is absent and the yield is 0·48 kg NaOH‐P/km²/year). Therefore, as since both detrimental and beneficial effects of sediment‐bound P loading in ice marginal receiving waters are possible (i.e. either reduced primary productivity owing to increased turbidity or P fertilization following desorption) there is a pressing need to assess the ambient P status of such environments and also the capacity for ice‐marginal ecosystems to adapt to such inputs. Copyright © 2004 John Wiley & Sons, Ltd.     

Evaluation of ASTER GDEM and SRTM and their suitability in hydraulic modelling of a glacial lake outburst flood in southeast Tibet

The resolution and accuracy of digital elevation models (DEMs) can affect the hydraulic simulation results for predicting the effects of glacial lake outburst floods (GLOFs). However, for the Tibetan Plateau, high‐quality DEM data are often not available, leaving researchers with near‐global, freely available DEMs, such as the Advanced Spaceborne Thermal Emission and Reflection Radiometer Global Digital Elevation Model (ASTER GDEM) and the Shuttle Radar Topography Mission data (SRTM) for hydraulic modelling. This study explores the suitability of these two freely available DEMs for hydraulic modelling of GLOFs. Our study focused on the flood plain of a potentially dangerous glacial lake in southeastern Tibet, to evaluate the elevation accuracy of ASTER GDEM and SRTM, and their suitability for hydraulic modelling of GLOFs. The elevation accuracies of ASTER GDEM and SRTM were first validated against field global position system (GPS) survey points, and then evaluated with reference to the relatively high precision of 1:50 000 scale DEM (DEM5) constructed from aerial photography. Moreover, the DEM5, ASTER GDEM and SRTM were used as basic topographic data to simulate peak discharge propagation, as well as flood inundation extent and depth in the Hydrologic Engineering Center's River Analysis System one‐dimensional hydraulic model. Results of the three DEM predictions were compared to evaluate the suitability of ASTER GDEM and SRTM for GLOF hydraulic modelling. Comparisons of ASTER GDEM and SRTM each with DEM5 in the flood plain area show root‐mean‐square errors between the former two as ± 15·4 m and between the latter two as ± 13·5 m. Although SRTM overestimates and ASTER GDEM underestimates valley floor elevations, both DEMs can be used to extract the elevations of required geometric data, i.e. stream centre lines, bank lines and cross sections, for flood modelling. However, small errors still exist in the cross sections that may influence the propagation of peak discharge. The flood inundation extent and mean water depths derived from ASTER GDEM predictions are only 2·2% larger and 2·3‐m deeper than that of the DEM5 predictions, whereas the SRTM yields a flood zone extent 6·8% larger than the DEM5 prediction and a mean water depth 2·4‐m shallower than the DEM5 prediction. The modelling shows that, in the absence of high‐precision DEM data, ASTER GDEM or SRTM DEM can be relied on for simulating extreme GLOFs in southeast Tibet. Copyright © 2011 John Wiley & Sons, Ltd.     

Composite suspended sediment particles and flocculation in glacial meltwaters: preliminary evidence from Alpine and Himalayan basins

Research over the last decade has shown that the suspended sediment loads of many rivers are dominated by composite particles. These particles are also known as aggregates or flocs, and are commonly made up of constituent mineral particles, which evidence a wide range of grain sizes, and organic matter. The resulting in situ or effective particle size characteristics of fluvial suspended sediment exert a major control on all processes of entrainment, transport and deposition. The significance of composite suspended sediment particles in glacial meltwater streams has, however, not been established. Existing data on the particle size characteristics of suspended sediment in glacial meltwaters relate to the dispersed mineral fraction (absolute particle size), which, for certain size fractions, may bear little relationship to the effective or in situ distribution. Existing understanding of composite particle formation within freshwater environments would suggest that in‐stream flocculation processes do not take place in glacial meltwater systems because of the absence of organic binding agents. However, we report preliminary scanning electron microscopy data for one Alpine and two Himalayan glaciers that show composite particles are present in the suspended sediment load of the meltwater system. The genesis and structure of these composite particles and their constituent grain size characteristics are discussed. We present evidence for the existence of both aggregates, or composite particles whose features are largely inherited from source materials, and flocs, which represent composite particles produced by in‐stream flocculation processes. In the absence of organic materials, the latter may result solely from electrochemical flocculation in the meltwater sediment system. This type of floc formation has not been reported previously in the freshwater fluvial environment. Further work is needed to test the wider significance of these data and to investigate the effective particle size characteristics of suspended sediment associated with high concentration outburst events. Such events make a major contribution to suspended sediment fluxes in meltwater streams and may provide conditions that are conducive to composite particle formation by flocculation. Copyright © 2002 John Wiley & Sons, Ltd.     

The Role of Fluvial and Glacial Erosion in Landscape Evolution: The Ben Ohau Range,New Zealand

A morphometric comparison of valleys has been made for the Ben Ohau Range in the central Southern Alps of New Zealand. The range is undergoing rapid tectonic transport and uplift. The humid north of the range is a glacial trough-and-arête landscape, with a temperate glacial climate. The dry south has rounded divides and plateau remnants dissected by fluvial valleys. Assuming that space–time substitution allows today's spatial valley-form transition to represent evolutionary stages in valley development, the tectonic history allows time constraints to be placed on the rate of transition to an alpine glacial landscape. Morphometric change has been quantified using hypsometric curves, and distance–elevation plots of cirque and valley-floor altitudes. Ancestral fluvial valleys have less concave long profiles but are stepped at altitude owing to the presence of high-level cirques and remnant plateau surfaces, and possess a low proportion of land area at low elevation. Increasing glacial influence is manifest as smoother, more deeply concave long profiles and U-shaped cross-profiles associated with a higher proportion of the land area at lower elevation. The full morphological transition has involved up to 2.4 km of vertical denudation over the 4 Ma lifetime of the mountain range, of which 80 per cent would have occurred by preglacial fluvial erosion. Combining the trajectory of tectonic transport with reconstructed glaciation limits and climatic history, it is indicated that about 200 ka of temperate glacial erosion produces recognizable trough-and areête topography. Mean and modal relief increase where glacial activity is confined to cirques, but decrease when trough incision by ice becomes established as a dominant process in the landscape. © 1997 by John Wiley & Sons, Ltd.     

Sediment transport in high‐speed flows over a fixed bed: 2. Particle impacts and abrasion prediction

Single bed load particle impacts were experimentally investigated in supercritical open channel flow over a fixed planar bed of low relative roughness height simulating high‐gradient non‐alluvial mountain streams as well as hydraulic structures. Particle impact characteristics (impact velocity, impact angle, Stokes number, restitution and dynamic friction coefficients) were determined for a wide range of hydraulic parameters and particle properties. Particle impact velocity scaled with the particle velocity, and the vertical particle impact velocity increased with excess transport stage. Particle impact and rebound angles were low and decreased with transport stage. Analysis of the particle impacts with the bed revealed almost no viscous damping effects with high normal restitution coefficients exceeding unity. The normal and resultant Stokes numbers were high and above critical thresholds for viscous damping. These results are attributed to the coherent turbulent structures near the wall region, i.e. bursting motion with ejection and sweep events responsible for turbulence generation and particle transport. The tangential restitution coefficients were slightly below unity and the dynamic friction coefficients were lower than for alluvial bed data, revealing that only a small amount of horizontal energy was transferred to the bed. The abrasion prediction model formed by Sklar and Dietrich in 2004 was revised based on the new equations on vertical impact velocity and hop length covering various bed configurations. The abrasion coefficient k_v was found to be vary around k_v ~ 10⁵ for hard materials (tensile strength f_t > 1 MPa), one order of magnitude lower than the value assumed so far for Sklar and Dietrich's model. Copyright © 2017 John Wiley & Sons, Ltd.     

Volcán Ecuador,Galapágos Islands: erosion as a possible mechanism for the generation of steep-sided basaltic volcanoes

Volcán Ecuador (0°02′S, 91°35′W) consists of two strongly contrasting components: the eroded and vegetated remnant of a once-circular main volcano with a probable caldera, and a prominent rift zone extending to the northeast that is neither strongly eroded nor weathered. There are about 20 young-looking flows and vents on this caldera floor but only one on the higher remnant of the main volcano. The southwest half of the main volcano is faulted into the ocean. The main part of Volcán Ecuador possesses steep erosional slopes (average 30–40°) that cut into a sequence of flows that dip radially outward at <10°. In contrast, the northeast rift zone consists entirely of young flows and vents. The upper 10 km of the rift zone forms a peninsula about 7.5 km wide that connects Volcán Ecuador to Volcán Wolf. The rift zone bends to the southeast and the lower 8 km is tangential to the coast of Volcán Wolf. The rift zone axis dips away from the northeast edge of the main volcano, and its flanks slope roughly northwest and southeast at <4°. The rift zone is the Galápagos structure that most closely resembles a Hawaiian rift zone because it is constructed of lavas from subparallel linear vents, shows evidence of a deep feeder conduit, and has changed its direction to avoid a direct intersection with neighboring Volcán Wolf. The steep erosional slopes extending around the perimeter of the main volcano (except to the southwest where slumping occurred) were probably generated by marine erosion during a prolonged period of eruptive inactivity (perhaps 20 000–30 000 years). Only a few post-erosional eruptions have taken place at the main volcano in and near what was once the caldera. The entire rift zone postdates the period of prolonged erosion. Using the evidence for prolonged inactivity at Volcán Ecuador, we propose that erosion may have helped to produce steep slopes on the other western Galápagos volcanoes. On these more active volcanoes, however, numerous subsequent eruptions have completely mantled the erosional slopes with lava. The mechanism by which the volcanoes may shut off for long periods of time is unknown, but the fact that the Galápagos hotspot is presently supplying nine active volcanoes suggests that the magma supply at an individual volcano could vary greatly over periods of (tens of?) thousands of years.     

Hillslope runoff and erosion as affected by rolled erosion control systems: a field study

A replicated field study using rainfall simulation and overland flow application was conducted in central Oahu, Hawaii, on a clay‐dominated Oxisol with a 9% slope. Three main treatment groups were examined: a bare treatment, a group of four rolled erosion control systems (RECSs) with open weave designs, and a group of five randomly oriented fibre RECSs. A total of 1122 measurements of runoff and erosion were made to examine treatment differences and to explore temporal patterns in runoff and sediment flux. All erosion control systems significantly delayed the time required to generate plot runoff under both simulated rainfall (35 mm h^?1) and the more intense trickle flow application (114 mm h^?1). Once runoff was generated during the rainfall application phase, the bare treatment runoff coefficients were significantly lower than those from the two groups of RECSs, as surface seal disruption by rilling is inferred to have enhanced infiltration in the bare treatments. During the more intense phase of overland flow application, the reverse pattern was observed. Interrill contributing‐area roughness was reduced on the bare treatment, facilitating increased runoff to well‐developed rill networks. Meanwhile, the form roughness associated with the RECSs delayed interrill flow to the poorly organized rills that formed under some of the RECSs. Regardless of runoff variations between treatments, sediment output was significantly lower from all surfaces covered by RECSs. The median cumulative sediment output from the bare surfaces was 6·9 kg, compared with 1·2 kg from the open‐weave RECSs and 0·2 kg from the random‐fibre RECSs. The random‐fibre systems were particularly effective under the more stressful overland flow application phase, with 63 times less sediment eroded than the bare treatments and 12 times less than that from the open‐weave systems. Architectural design differences between the two groups of RECSs are discussed in light of their relation to erosion process dynamics and shear stress partitioning. Copyright © 2006 John Wiley & Sons, Ltd.     

Lateral water flux in the unsaturated zone: A mechanism for the formation of spatial soil heterogeneity in a headwater catchment

Measurements of soil water potential and water table fluctuations suggest that morphologically distinct soils in a headwater catchment at the Hubbard Brook Experimental Forest in New Hampshire formed as a result of variations in saturated and unsaturated hydrologic fluxes in the mineral soil. Previous work showed that each group of these soils had distinct water table fluctuations in response to precipitation; however, observed variations in soil morphology also occurred above the maximum height of observed saturation. Variations in unsaturated fluxes have been hypothesized to explain differences in soil horizon thickness and presence/absence of specific horizons but have not been explicitly investigated. We examined tensiometer and shallow groundwater well records to identify differences in unsaturated water fluxes among podzols that show distinct morphological and chemical differences. The lack of vertical hydraulic gradients at the study sites suggests that lateral unsaturated flow occurs in several of the soil units. We propose that the variations in soil horizon thickness and presence/absence observed at the site are due in part to slope‐parallel water flux in the unsaturated portion of the solum. In addition, unsaturated flow may be involved in the translocation of spodic material that primes those areas to contribute water with distinct chemistry to the stream network and represents a potential source/sink of organometallic compounds in the landscape.