2020年1月19日伽师6.4级地震强震动记录特征分析

以新疆强震动台网获取的伽师6.4级地震的42组126条原始加速度记录为依据,对强震动记录时程、幅值、频谱三方面进行分析。结果表明,此次地震获取的最大加速度峰值为633.3cm/s²,仪器地震烈度为Ⅸ度;在震中距200km以内两水平向与垂直向加速度峰值比在1~3之间,速度峰值比在0~4之间。分析此次地震三分向加速度峰值衰减关系,0~50km范围内地震峰值加速度观测值在分区地震动衰减关系(Yu13)长轴预测值误差范围之内,高于南天山西段土层衰减关系(Zhang)预测值;水平向加速度反应谱卓越周期主要集中在0~0.5s,垂直向集中在0~0.2s。65XKR台水平向反应谱高于Ⅷ度罕遇地震设计反应谱,峰值卓越周期为0.48s;垂直向反应谱高于Ⅷ度罕遇地震设计反应谱,峰值位于高频段。     

基于《建筑抗震设计规范》强度包线函数参数取值研究

利用《中国地震动参数区划图》采用的地震动参数衰减关系,以及《中国地震动参数区划图》中地震动峰值加速度和地震动加速度反应谱特征周期反推不同设防烈度和设计地震分组对应的震级和震中距,再根据《建筑抗震设计规范》中各设防水准的峰值加速度确定对应的震级和震中距,进而根据地震动强度包线参数与震级和震中距关系计算地震动强度包线参数的取值,为基于强度包线函数生成人工地震动提供参考,并讨论强度包线参数的取值规律：(1)随着设防烈度的提高,加速度时程曲线上升段持续时间t₁和平稳段持续时间t_s减小,下降段衰减指数c增大;(2)随着地震水准和设计地震分组的提高,加速度时程曲线上升段持续时间t₁和平稳段持续时间t_s增加,下降段衰减指数c减小;(3)在生成人工地震动时,除考虑峰值加速度和设计地震分组影响外,还需要考虑设防烈度影响。     

地震动参数在建筑物抗震设计中的应用

传统考虑后期使用年限的地震动参数研究,在建筑物抗震设计中的应用,缺乏地震危险性分析和建筑物损伤指数分析,应用性差。提出新的地震动参数在建筑物抗震设计中的应用方法,以地震危险性分析为基础,通过水平地震动加速度衰减关系方程,求得建筑场地水平向基岩峰值加速度和反应谱,以此得到地震动加速度反应谱方程,利用该方程获得地震动反应谱参数,采用变形和线性组合构建损伤指数模型,获取地震波作用下地震动参数对建筑物损伤程度。实验结果表明,利用所提方法得到的地震动反应谱最小误差为0.563,小于允许误差4.0;在50年超越概率63%的条件下地震动参数值分别为0.26、0.095,所提方法可在规定误差范围内得到地震动反应谱参数值,其进行建筑物抗震设计精度和应用性高。     

2019年10月28日甘肃夏河5.7级地震强地面运动特征分析

2019年10月28日甘肃省夏河县发生5.7级地震,中国数字强震动台网的18个专业台站在此次地震中触发。本文处理捕获的54条三分向加速度记录,给出近场台站的地震动参数,绘制了震中附近区域峰值加速度等值线图,其长轴呈WN-ES方向展布。将实际观测数据与几种常用地震动衰减关系对比,发现俞言祥^[1]短轴衰减预测模型能更好地反映此次地震的影响场。将振幅较大的62LBL、62BLX台的反应谱与我国抗震设计反应谱比较,采用最小二乘法拟合出不同震中距5个台站各周期谱加速度衰减特性,总结了此次地震的反应谱基本特征。运用H/V谱比法对4个典型台站进行场地地震反应分析,研究了局部场地条件对峰值加速度和峰值速度的影响过程。     

新疆安居房屋抗震能力的试验研究

为科学评定新疆安居房屋的抗震能力,通过1/2大比例尺新疆安居房屋模型模拟地震振动台试验,研究设置构造柱与圈梁的新疆安居房屋模型在地震作用下的破坏特征以及地震反应。试验结果表明,在峰值加速度为0.1 g~0.3 g地震动作用下,模型处于完好状态。在峰值加速度0.4 g地震动作用下,模型墙体出现开裂。在峰值加速度1.2 g地震动作用下,墙体发生明显破坏但未倒塌,构造柱和圈梁基本完好。试验结果证实设置构造柱和圈梁是提高砌体房屋抗倒塌能力的一种有效措施,新疆安居房屋具有良好的抗震能力。     

2022年9月5日泸定MS6.8地震宽频带地震动谱元法模拟

2022年9月5日12时52分四川甘孜州泸定县发生M_S6.8地震,此次地震造成泸定县及其周边地域的严重破坏和人员的重大伤亡。为重现此次地震的地震动影响场,分析近场强地面运动的空间分布特征,将确定性的凹凸体震源模型与随机震源模型结合得到有限断层运动学混合震源模型,进而将上述混合震源模型开发到SPECFEM 3D谱元法开源代码中,实现了基于谱元法和运动学混合震源模型的泸定M_S6.8地震的全过程宽频带(0.1—5 Hz)地震动模拟,通过与六个台站的时程记录、对应的反应谱以及NGA-West2地震动衰减曲线进行比较检验了方法的精度和适用性;进而给出了此次地震的三分量速度波场快照图,再现了地震波传播时近场地震动的方向性效应和局部场地效应;最后给出了震中100 km×100 km范围内的地震动峰值加速度(PGA)和峰值速度(PGV)云图,分析了泸定地震近场强地面运动的空间分布特征,并给出了基于模拟结果的地震烈度分布图。结果显示,震中PGA接近600 cm/s²,PGV接近50 cm/s,烈度达到Ⅸ度,且由于泸定地区内高山峡谷地形对地...     

2018年陕西宁强5.3级地震强地面运动特征及局部场地效应分析

2018年9月12日陕西省宁强县发生5.3级地震,中国数字强震动台网的39个专业台站在此次地震中触发。文章中通过处理捕获的117条三分向加速度记录,给出近场台站的地震动参数,绘制震中附近区域峰值加速度等值线图,其长轴呈西南-东北方向展布。采用实际观测数据与几种常用地震动衰减关系对比,发现霍俊荣衰减预测模型能更好地反映此次地震的影响场。将振幅最大的51GYD台的反应谱与我国抗震设计反应谱比较,采用最小二乘法拟合出不同震中距5个台站各周期谱加速度衰减特性,总结出此次地震的反应谱基本特征。运用H/V谱比法对51GYD土层台和62ZM台阵进行局部场地地震反应分析,研究覆盖土层对地震动的放大作用,及局部地形对峰值加速度和峰值速度的影响过程。     

2013年8月新疆乌鲁木齐市5.1级地震强震动记录及特征分析

2013年8月30日乌鲁木齐市发生M_S5.1地震,乌鲁木齐烈度速报台网有32个强震动台触发获得了主震加速度记录。选取23条强震动记录进行常规处理,统计强震动记录数量随震中距分布,对比分析此次地震峰值加速度(PGA)与新疆土层加速度衰减关系;并利用强震动数据对此次地震进行定位,定位结果对应台站震中距与到时线性度较好;最后分析了典型强震动台站记录特性与建筑物震害及工程震害相关性。     

双向地震作用下锯末混合土场地动力特性分析

在北京工业大学振动台台阵系统上开展了一系列锯末混合土地基自由场振动台模型试验,试验中模型箱采用装配式连续体刚性模型箱,试验中输入地震动时程采用El Centro地震动记录、Taft地震动记录和天津地震动记录,地震动输入方向分为水平单向和水平双向。文中,重点考察了双向地震动输入下锯末混合土模型场地的动力特性及其变化规律,主要指标包括模型场地地震动反应的峰值加速度及其动力放大系数、加速度时程及其傅氏谱。试验结果表明:随着输入地震动强度的增大,同一测点反应的峰值加速度总体上在增大,而其加速度动力放大系数总体上呈现减小的趋势,反应的频谱组成从较高频率向较低频率移动;双向地震作用下锯末混合土模型场地的动力变化规律与单向地震作用下较为一致。     

地形效应影响下地震动参数与斜坡稳定性的相关性研究

地形对地震动的影响比较复杂, 考虑地形放大效应的地震滑坡稳定性分析需要选择合适的地震动参数. 本文使用自贡地形影响台阵记录到的2008年汶川M_S8.0地震主震加速度记录, 分析了地震动峰值加速度、 阿里亚斯烈度以及90%能量持时随地形高度的变化, 探讨了地形效应作用下峰值加速度和阿里亚斯烈度与地震动作用下斜坡稳定性的相关性. 结果表明: ① 地形场地对峰值加速度和阿里亚斯烈度均有显著的放大效应. 地形放大效应较为复杂, 其整体上随台站高度的增加而增大, 水平向的放大效应大于竖直向. 水平向峰值加速度的放大系数为1.1—1.8, 阿里亚斯烈度的放大系数为1.2—3.3; 竖直向相应放大系数分别为1.1—1.3和1.2—1.7. ② 地形对地震动持时也有一定的放大效应, 但不同高度、 不同分量的放大效应没有显著差异, 其放大系数均约为1.3. ③ 阿里亚斯烈度和峰值加速度均能很好地表征地形对地震动的影响, 与地震动对斜坡稳定性的影响具有很强的相关性. 与峰值加速度相比, 阿里亚斯烈度综合了地震动的多方面特征, 可以更好地表征地形对地震动的影响, 与地震动作用下斜坡稳定性的相关性更强.      

河北永清M 4.3地震北京烈度仪台网记录分析

2018年2月12日河北永清发生M 4.3地震,北京烈度仪台网共35个台站获得有效记录,记录最大峰值加速度的台站为丰台地震台（D0001）,峰值加速度为10.76cm/s2,该台距震中约61km。本文对北京烈度仪台网获得的此次地震动记录进行了初步分析,并对3个同台址的强震动仪记录的数据进行了对比分析。结果表明,烈度仪记录计算得出的仪器烈度与强震动仪记录计算的仪器烈度结果具有较高的一致性,可用于烈度速报。     

基于BIM的建筑地震受损程度评估模型设计

由于在变形和累积耗能的建筑地震受损程度评估模型,是将建筑划分为五个状态水平,未研究建筑环境性能,评估结果误差较大。因此设计基于BIM的建筑地震受损程度评估模型,采用基于BIM的建筑环境研究与评估方法,考虑建筑环境性能,基于这个思路,依据混凝土单轴Mazars损伤模型,获取三轴状态中的损伤演化方程,得到应变大于损伤阈值时损伤演化方程增量形式,构建混凝土损伤评估模型。经实验证明,所设计模型在地震峰值加速度小于0.31g时,建筑结构大致无缺,在峰值加速度是0.61g时,建筑地震受损指数超过0.8,建筑倒塌;所设计模型评估的平均误差低于0.03,平均评估时间是2.86 s,说明所设计模型能够有效评估建筑地震受损程度,且精度和效率较高。     

Estimation of Strong Ground Motion from a Great Earthquake Mw 8.5 in Central Seismic Gap Region, Himalaya (India) Using Empirical Green’s Function Technique

In the present study ground motions for a Mw 8.5 scenario earthquake are estimated at 13 sites in Kumaun-Garhwal region using the empirical Green’s function technique. The recordings of 1991 Uttarkashi earthquake of Mw 6.8 at these sites are used as an element earthquake. A heterogeneous source model consisting of two asperities is considered for simulating the ground motions. The entire central seismic gap (CSG) can expect acceleration in excess of 100 cm/s² with NW portion in excess of 400 cm/s² and SE between 100 and 200 cm/s². The central portion can expect peak ground acceleration (PGA) between 200 and 400 cm/s². It has been observed from simulation of strong ground motion that sites located near the rupture initiation point can expect accelerations in excess of 1g. In the present analysis, Bhatwari and Uttarkashi can expect ground accelerations in excess of 1g. The estimates of the PGA are compared with earlier studies in the same region using different methodologies and it was found that the results are comparable. This has put constrains on the expected PGAs in this region. The obtained PGA values can be used in identifying the vulnerable areas in the central Himalaya, thereby facilitating the planning, design and construction of new structures and strengthening of the existing structures in the region.     

Probability of Peak Ground Horizontal and Peak Ground Vertical Accelerations at Tehran and Surrounding Areas

The active faults near Tehran are capable of producing Mw magnitudes of 6.62?C7.23; at epicentral distances of 25?km from the active faults, and Mw?=?7.23, the peak ground horizontal acceleration, PGH, is between 386 and 730?cm/s² and peak ground vertical acceleration, PGV, is between 192 and 261?cm/s²; the historic earthquake of the fourth century BC, Mw?=?7.16 produced the highest estimated PGH acceleration in Tehran, between 254 and 479?cm/s² and PGV acceleration between 127 and 173?cm/s². Earthquakes from 1909 to 2008, within 300?km from Tehran, are used for calculation of magnitude frequency relation, and results are applied to estimate PGH and PGV accelerations as a function of magnitudes for a set of fixed epicentral distance and site conditions; also as a function of epicentral distances for a set of fixed magnitudes and site conditions. Poisson??s distribution is used for probability calculation of PGH and PGV accelerations for several exposure times, site conditions and epicentral distances; accelerations with very high probability, near 1, are presented. At an epicentral distance of 10?km and exposure time of 450?years, in the northern part of Tehran, close to Mosha and the Northern Tehran faults, PGH acceleration is 800?C420?cm/s² and PGV is 400?C220?cm/s² with high probability. At an epicentral distance of 25?km and 1,000?years exposure time, PGH is 610?C320?cm/s² and PGV is 310?C160?cm/s² with high probability, where larger values are for soft soil and smaller values are for hard rock.     

高层钢结构建筑横向支撑地震动力响应分析

为测试高层钢结构建筑抗震性能,在有限元模型中以某高层钢框架结构办公大厦作为研究对象,测试其横向支撑地震动力响应状况。选取地震峰值加速度为200 cm/s^2的El-Centro波作为地震波输入,采用瞬态动力方法分析不同楼板厚度下建筑地震模拟响应,得到建筑顶层位移时程曲线;在SAP2000结构软件中分析建筑工程添加横向支撑前后的反应谱,记录各楼层垂直与水平方向位移与层间位移角。得到如下结果:高层钢结构建筑在地震响应下产生的位移不随楼板厚度的增加而增大,楼板厚度为100 mm、170 mm时位移波动显著;添加横向支撑后,建筑水平刚度显著提升,同理,添加横向支撑后横向层间位移角的最大值变化较大,且低于1/250,符合相关建筑标准。     

Field survey around strong motion stations and its implications on the seismic intensity in the Lushan earthquake on April 20, 2013

The M _s7.0 Lushan earthquake on April 20, 2013 is another destructive event in China since the M _s8.0 Wenchuan earthquake in 2008 and M _s7.1 Yushu earthquake in 2010. A large number of strong motion recordings were accumulated by the National Strong Motion Observation Network System of China. The maximum peak ground acceleration (PGA) at Station 51BXD in Baoxing Country is recorded as ?1,005.3 cm/s², which is even larger than the maximum one in the Wenchuan earthquake. A field survey around three typical strong motion stations confirms that the earthquake damage is consistent with the issued map of macroseismic intensity. For the oscillation period 0.3–1.0 s which is the common natural period range of the Chinese civil building, a comparison shows that the observed response spectrums are considerably smaller than the designed values in the Chinese code and this could be one of the reasons that the macroseismic intensity is lower than what we expected despite the high amplitude of PGAs. The Housner spectral intensities from 16 stations are also basically correlated with their macroseismic intensities, and the empirical distribution of spectral intensities from Lushan and Wenchuan Earthquakes under the Chinese scale is almost identical with those under the European scale.     

Estimation of Strong Ground Motions for 2001 Bhuj (M w 7.6), India Earthquake

The strong ground motions for the 2001 Bhuj (M _w 7.6) India earthquake have been estimated on hard rock and B/C boundary (NEHRP) levels using a recently modified version of stochastic finite fault modeling based on dynamic corner frequency (Motazedian and Atkinson in Bull Seismol Soc Am 95, 995–1010 2005). Incorporation of dynamic corner frequency removes the limitations of earlier stochastic methods. Simulations were carried out at 13 sites in Gujarat where structural response recorder (SRR) recordings are available. In addition, accelerograms were simulated at the B/C boundary at a large number of points distributed on a grid. The corresponding response spectra have also been estimated. The values of peak ground accelerations and spectral accelerations at three periods (0.4, 0.75 and 1.25 s) are presented in the form of contour maps. The maximum value of peak ground acceleration (PGA) in the center of meizoseismal zone is 550 cm/s². The response spectral acceleration in same zone is 900 cm/s² (T = 0.4 s), 600 cm/s² (T = 0.75 s) and 300 cm/s² (T = 1.25 s). The innermost PGA contour is on the fault plane. A comparison of the PGA values obtained at 13 sites in this study with those obtained in earlier studies on the same sites, but employing different methods, show that the present PGA values are comparable at most of the sites. The rate of decay of PGA values is fast at short distances as compared to that at longer distances. The PGA values obtained here put some constraints on the expected values from a similar earthquake in the region. A synthetic intensity map has been prepared from the estimated values of PGA using an empirical relation. A comparison with the reported intensity map of the earthquake shows the synthetic MMI values, as expected, are lower by 1 unit compared to reported intensity map. The contour map of PGA along with the contour maps of spectral acceleration at various periods permit the assessment of damage potential to various categories of houses and other structures. Such information will be quite important in planning of mitigation and disaster management programs in the region.     

基于IDA的方钢管混凝土框架-SPSW核心筒结构地震易损性研究

为研究方钢管混凝土框架-钢板剪力墙（SPSW）核心筒结构在不同强度地震下破坏概率,使用拉杆模型作为钢板剪力墙等效模型,与已有试验对比验证各参数有效性。以地震动峰值加速度（PGA）作为地震动强度参数,按照场地条件等要求选择11条地震动记录。以结构最大层间位移角作为损伤指标,对一典型方钢管混凝土框架-钢板剪力墙核心筒结构进行增量动力分析（IDA）,得到IDA曲线簇。基于增量动力分析进行易损性分析,得到易损性曲线,并计算结构的抗倒塌储备系数。结果表明:8度多遇地震作用下,此结构处于正常使用状态。8度设防地震作用下,处于修复后可使用状态。8度罕遇地震作用下,处于生命安全状态。表明该结构具有良好的抗震性能,满足规范中“小震不坏”、“中震可修”和“大震不倒”的抗震设防目标。该结构抗倒塌储备系数大于规范建议值,具有较好的抗倒塌能力。     

Strong motion envelope modelling of the source of the Chamoli earthquake of March 28, 1999 in the Garhwal Himalaya, India

Garhwal Himalaya has been rocked by two major earthquakes in the span of just eight years, viz. Uttarkashi earthquake of 20th Oct, 1991 and Chamoli earthquake of 28th March, 1999. Chamoli earthquake of March 28, 1999 was recorded at 11 different stations of a strong motion array installed in the epicentral region. The maximum peak ground acceleration (353 cm/s²) was recorded at an accelerograph located at Gopeshwar. The data from eleven stations has been used for comparison with the simulated acceleration envelopes due to a model of the rupture responsible for this earthquake. For simulation of acceleration envelope the method of Midorikawa (1993) has been modified for its applicability to Himalayan region. This method has earlier been used by Joshi and Patel (1997) and Joshi (1999) for the studyof Uttarkashi earthquake of 20th Oct, 1991. The same method has been used for study of Chamoli earthquake. Layered earth crust has been introduced in place of homogeneous one in this method. The model of rupture is placed at a depth of 12 km below the Munsiari thrust for modelling Chamoli earthquake. Peak ground acceleration was calculated from simulated acceleration envelope using layered as well as homogeneous earth crust. For the rupture placed in a layered crust model peak ground acceleration of order 312 cm/s² was simulated at Gopeshwar which is quite close to actually recorded value. The comparison of peak ground acceleration values in terms of root mean square error at eleven stations suggests that the root mean square error is reduced by inclusion of a layered earth crust in place of homogeneous earth crust.     

Rapid report of seismic damage to buildings in the 2022 M 6.8 Luding earthquake,China

The report summarizes the observed damage to a variety of buildings near the epicenter of the M6.8 Luding earthquake in Sichuan Province, China. They include base-isolated buildings, multi-story reinforced concrete (RC) frame buildings, and masonry buildings. The near-field region is known to be tectonically highly active, and the local intensity level is the highest, that is, 0.4g peak ground acceleration (PGA) for the design basis earthquake, in the Chinese zonation of seismic ground motion parameters. The extent of damage ranged from the weak-story collapse that claimed lives to the extensive nonstructural damage that suspended occupancy. The report highlights the first observation of the destruction of rubber bearings and viscous dampers in the isolation layer of Chinese seismically isolated buildings. It also features the rare observation of the brittle shear failure of RC columns in moment-resisting frames in a region of such a high seismic design requirement. Possible reasons that may have attributed to the reported damage are suggested by providing facts observed in the field. However, careful forensic analyses are needed before any conclusive judgment can be made.