Vertical Contaminant Profiling of Volatile Organic* in a Deep Fractured Basalt Aquifer

Volatile organic compounds delected in ground water from wells at Test Area North (TAN) at the Idaho National Engineering Laboratory (INEL) prompted RCRA facility investigations in 1989 and 1990 and a CERCLA-driven RI/FS in 1992. In order to address ground water treatment feasibility, one of the main objectives, of the 1992 remedial investigation was to determine the vertical extent of ground water contamination, where the principle contaminant, of concern is trichloroethylene (TCE). It was hypothesized that a sedimentary interbed at depth in the fractured basalt aquifer could be inhibiting vertical migration of contaminants to lower aquifers. Due to the high cost of drilling and installation of ground water monitoring wells at this facility (greater than $100,000 per well), a real time method was proposed for obtaining and analyzing ground water samples during drilling to allow accurate placement of well screens in zones of predicted VOC contamination. This method utilized an inflatable pump packer pressure transducer system interfaced with a datalogger and PC at land surface. This arrangement allowed for real lime monitoring of hydraulic head above and below the packer to detect leakage around the packer during pumping and enabled collection of head data during pumping for estimating hydrologic properties. Analytical results were obtained in about an hour from an on-site mobile laboratory equipped with a gas chromalograplvmass spectrometer (GC/MS). With the hydrologic and analytical results in hand, a decision was made to either complete the well or continue drilling to the next test zone. In almost every case, analytical results of ground water samples taken from the newly installed wells closely replicated the water quality of ground water samples obtained through the pump packer system.     

Assessing Methane in Shallow Groundwater in Unconventional Oil and Gas Play Areas,Eastern Kentucky

The expanding use of horizontal drilling and hydraulic fracturing technology to produce oil and gas from tight rock formations has increased public concern about potential impacts on the environment, especially on shallow drinking water aquifers. In eastern Kentucky, horizontal drilling and hydraulic fracturing have been used to develop the Berea Sandstone and the Rogersville Shale. To assess baseline groundwater chemistry and evaluate methane detected in groundwater overlying the Berea and Rogersville plays, we sampled 51 water wells and analyzed the samples for concentrations of major cations and anions, metals, dissolved methane, and other light hydrocarbon gases. In addition, the stable carbon and hydrogen isotopic composition of methane (δ¹³C‐CH₄ and δ²H‐CH₄) was analyzed for samples with methane concentration exceeding 1 mg/L. Our study indicates that methane is a relatively common constituent in shallow groundwater in eastern Kentucky, where methane was detected in 78% of the sampled wells (40 of 51 wells) with 51% of wells (26 of 51 wells) exhibiting methane concentrations above 1 mg/L. The δ¹³C‐CH₄ and δ²H‐CH₄ ranged from ?84.0‰ to ?58.3‰ and from ?246.5‰ to ?146.0‰, respectively. Isotopic analysis indicated that dissolved methane was primarily microbial in origin formed through CO₂ reduction pathway. Results from this study provide a first assessment of methane in the shallow aquifers in the Berea and Rogersville play areas and can be used as a reference to evaluate potential impacts of future horizontal drilling and hydraulic fracturing activities on groundwater quality in the region.     

An Analytical Model for Hydraulic Fracturing in Shallow Bedrock Formations

A theoretical method is proposed to estimate post‐fracturing fracture size and transmissivity, and as a test of the methodology, data collected from two wells were used for verification. This method can be employed before hydrofracturing in order to obtain estimates of the potential hydraulic benefits of hydraulic fracturing. Five different pumping test analysis methods were used to evaluate the well hydraulic data. The most effective methods were the Papadopulos‐Cooper model (1967), which includes wellbore storage effects, and the Gringarten‐Ramey model (1974), known as the single horizontal fracture model. The hydraulic parameters resulting from fitting these models to the field data revealed that as a result of hydraulic fracturing, the transmissivity increased more than 46 times in one well and increased 285 times in the other well. The model developed by dos Santos (2008) , which considers horizontal radial fracture propagation from the hydraulically fractured well, was used to estimate potential fracture geometry after hydrofracturing. For the two studied wells, their fractures could have propagated to distances of almost 175 m or more and developed maximum apertures of about 2.20 mm and hydraulic apertures close to 0.30 mm. Fracturing at this site appears to have expanded and propagated existing fractures and not created new fractures. Hydraulic apertures calculated from pumping test analyses closely matched the results obtained from the hydraulic fracturing model. As a result of this model, post‐fracturing geometry and resulting post‐fracturing well yield can be estimated before the actual hydrofracturing.     

Analysis of Transient Flow to an Extended Fully Penetrating Well at Constant-Head Pumping

Vertical wells with radial extension at the well bottom can improve the rate of water production. No study has yet investigated the effects of the transient state and anisotropy in directional hydraulic conductivities on the wellbore flux rate for this type of well. This study derives a semianalytical transient drawdown solution for constant-head pumping at a fully penetrating well radially extended at the bottom of a confined, anisotropic aquifer by applying Laplace transform and separation of variables as well as conducting a Fourier analysis. The results of this new solution indicate that transient and steady-state wellbore flux rates can be increased by a factor of two for greater radial extension of the well. Compared with an isotropic aquifer (a ratio of vertical and horizontal hydraulic conductivities equal to one), an anisotropic aquifer with the ratio less than one may produce a higher transient wellbore flux rate and lower steady-state wellbore flux rate. Moreover, the time required to achieve the steady-state wellbore flux rate can be substantially affected by anisotropy of the aquifer.     

Organic Contaminants in Portland Cements Used in Monitoring Well Construction

We report the results of two independent laboratory investigations to evaluate total and leachable concentrations of glycols, glycol ethers, phenol, and other compounds in representative Type I and Type I/II Portland cement products that United States Environmental Protection Agency (EPA), The American Society of Testing and Materials (ASTM) and others recommend as annular sealants in monitoring well completions. Water well drillers also use these cements in their well completions. The EPA has included some of these compounds for analysis in their National Hydraulic Fracturing Study to evaluate the effects of hydraulic fracturing on ground‐ and surface water resources. During any contaminant investigation, materials used in monitoring or water well drilling, completion, development, and sampling must be free of the chemicals being targeted by the regulatory agency. Three of five bulk cement products we tested contained part per million (ppm) (mg/kg) concentrations of diethylene glycol, ethylene glycol, tetraethylene glycol, and triethylene glycol; chemicals added as grinding aids during manufacture. Some cements also contained ppb (µg/kg) concentrations of benzoic acid, phenols, propylene glycol, and 2‐butoxyethanol. Leaching of cured cement samples in water produced ppm (mg/L) concentrations of glycols in the supernatant. These results show that cured cements in monitoring or water wells can contaminate groundwater samples with glycols and phenol. Our findings should help prevent future sample bias and false positives when testing for glycol compounds and phenol in groundwater samples from monitoring or water wells and highlight the need to test materials or products used in monitoring or water well drilling, completions, development, and sampling to avoid false positives when sampling and analyzing for less common analytical constituents.     

Performance Assessments of a Novel Well Design for Reducing Exposure to Bedrock‐Derived Arsenic

Arsenic in groundwater is a serious problem in New England, particularly for domestic well owners drawing water from bedrock aquifers. The overlying glacial aquifer generally has waters with low arsenic concentrations but is less used because of frequent loss of well water during dry periods and the vulnerability to surface‐sourced bacterial contamination. An alternative, novel design for shallow wells in glacial aquifers is intended to draw water primarily from unconsolidated glacial deposits, while being resistant to drought conditions and surface contamination. Its use could greatly reduce exposure to arsenic through drinking water for domestic use. Hypothetical numerical models were used to investigate the potential hydraulic performance of the new well design in reducing arsenic exposure. The aquifer system was divided into two parts, an upper section representing the glacial sediments and a lower section representing the bedrock. The location of the well, recharge conditions, and hydraulic properties were systematically varied in a series of simulations and the potential for arsenic contamination was quantified by analyzing groundwater flow paths to the well. The greatest risk of arsenic contamination occurred when the hydraulic conductivity of the bedrock aquifer was high, or where there was upward flow from the bedrock aquifer because of the position of the well in the flow system.     

A novel analytical solution for a slug test conducted in a well with a finite-thickness skin

An aquifer containing a skin zone is considered as a two-zone system. A mathematical model describing the head distribution is presented for a slug test performed in a two-zone confined aquifer system. A closed-form solution for the model is derived by Laplace transforms and Bromwich integral. This new solution is used to investigate the effects of skin type, skin thickness, and the contrast of skin transmissivity to formation transmissivity on the distributions of dimensionless hydraulic head. The results indicate that the effect of skin type is marked if the slug-test data is obtained from a radial two-zone aquifer system. The dimensionless well water level increases with the dimensionless positive skin thickness and decreases as the dimensionless negative skin thickness increases. In addition, the distribution of dimensionless well water level due to the slug test depends on the hydraulic properties of both the wellbore skin and formation zones.     

Predicting Collector Well Yields with MODFLOW

Groundwater flow models are commonly used to design new wells and wellfields. As the spatial scale of the problem is large and much local‐scale detail is not needed, modelers often utilize two‐dimensional (2D) or quasi three‐dimensional models based on the Dupuit‐Forchheimer assumption. Dupuit models offer a robust set of tools for simulating regional groundwater flow including interactions with surface waters, the potential for well interference, and varying aquifer properties and recharge rates. However, given an assumed operating water level or drawdown at a well screen, Dupuit models systematically overpredict well yields. For design purposes, this discrepancy is unacceptable, and a method for predicting accurate well yields is needed. While published methods exist for vertical wells, little guidance is available for predicting yields in horizontal screens or collector wells. In plan view, a horizontal screen has a linear geometry, and will likely extend over several neighboring cells that may not align with rows or columns in a numerical model. Furthermore, the model must account for the effects of converging three‐dimensional (3D) flow to the well screens and hydraulic interference among the well screens; these all depend on the design of a specific well. This paper presents a new method for simulating the yield of angled or horizontal well screens in numerical groundwater flow models, specifically using the USGS code MODFLOW. The new method is compared to a detailed, 3D analytic element model of a collector well in a field of uniform flow.     

A Semi‐Structured MODFLOW‐USG Model to Evaluate Local Water Sources to Wells for Decision Support

In order to better represent the configuration of the stream network and simulate local groundwater‐surface water interactions, a version of MODFLOW with refined spacing in the topmost layer was applied to a Lake Michigan Basin (LMB) regional groundwater‐flow model developed by the U.S. Geological. Regional MODFLOW models commonly use coarse grids over large areas; this coarse spacing precludes model application to local management issues (e.g., surface‐water depletion by wells) without recourse to labor‐intensive inset models. Implementation of an unstructured formulation within the MODFLOW framework (MODFLOW‐USG) allows application of regional models to address local problems. A “semi‐structured” approach (uniform lateral spacing within layers, different lateral spacing among layers) was tested using the LMB regional model. The parent 20‐layer model with uniform 5000‐foot (1524‐m) lateral spacing was converted to 4 layers with 500‐foot (152‐m) spacing in the top glacial (Quaternary) layer, where surface water features are located, overlying coarser resolution layers representing deeper deposits. This semi‐structured version of the LMB model reproduces regional flow conditions, whereas the finer resolution in the top layer improves the accuracy of the simulated response of surface water to shallow wells. One application of the semi‐structured LMB model is to provide statistical measures of the correlation between modeled inputs and the simulated amount of water that wells derive from local surface water. The relations identified in this paper serve as the basis for metamodels to predict (with uncertainty) surface‐water depletion in response to shallow pumping within and potentially beyond the modeled area, see Fienen et al. (2015a).     

Influence of a thin veneer of low‐hydraulic‐conductivity sediment on modelled exchange between river water and groundwater in response to induced infiltration

A thin layer of fine‐grained sediment commonly is deposited at the sediment–water interface of streams and rivers during low‐flow conditions, and may hinder exchange at the sediment–water interface similar to that observed at many riverbank‐filtration (RBF) sites. Results from a numerical groundwater‐flow model indicate that a low‐permeability veneer reduces the contribution of river water to a pumping well in a riparian aquifer to various degrees, depending on simulated hydraulic gradients, hydrogeological properties, and pumping conditions. Seepage of river water is reduced by 5–10% when a 2‐cm thick, low‐permeability veneer is present on the bed surface. Increasing thickness of the low‐permeability layer to 0·1 m has little effect on distribution of seepage or percentage contribution from the river to the pumping well. A three‐orders‐of‐magnitude reduction in hydraulic conductivity of the veneer is required to reduce seepage from the river to the extent typically associated with clogging at RBF sites. This degree of reduction is much larger than field‐measured values that were on the order of a factor of 20–25. Over 90% of seepage occurs within 12 m of the shoreline closest to the pumping well for most simulations. Virtually no seepage occurs through the thalweg near the shoreline opposite the pumping well, although no low‐permeability sediment was simulated for the thalweg. These results are relevant to natural settings that favour formation of a substantial, low‐permeability sediment veneer, as well as central‐pivot irrigation systems, and municipal water supplies where river seepage is induced via pumping wells. Published in 2011 by John Wiley & Sons, Ltd.     

Evaluation of Pumping Induced Flow in Observation Wells During Aquifer Testing

The vertical variation of drawdown around pumping wells generates an induced flow in the observation wells. A set of governing equations is presented to couple the drawdown variation and the vertical flux distribution in observation wells. A numerical example is performed to justify the governing equations and to verify the solution methods used by the simulation software WT. The example analyzes the effect of skin loss, wellbore storage, and vertical segmentation on the drawdown and induced flow in observation well during pumping. The evaluation of the Fairborn pumping test involves a vertically homogeneous and anisotropic water table aquifer, uniform well‐face drawdown conditions in the pumping well and simulation of the drawdown evolution in the observation well with and without the effect of induced flow. The computer calibrations resulted in small differences between the measured and simulated drawdown curves.     

A Method to Evaluate the Vertical Distribution of VOCs in Ground Water in a Single Borehole

Volatile organic compounds (VOCs) are present in multiple water-bearing zones beneath and downgradient of Lawrence Livermore National Laboratory. This area is composed of interfingering unconsolidated alluvial sediments with hydraulic conductivities ranging over four orders of magnitude. The more permeable sediments exhibit moderate hydraulic interconnection horizontally and less interconnection vertically, and appear to consist largely of interconnected stream channel deposits. To optimize selection of monitoring well screened intervals in this complex environment, a technique that enables collection of saturated formation samples from each water-bearing zone without contamination from other VOC-containing zones was developed, tested, and implemented. The technique utilizes a wireline punch-coring system that allows the drill bit to be replaced with a core barrel without removing the drill rod from the borehole. To help ensure that a sample from one water-bearing zone is not contaminated by VOCs from another zone, the drilling fluid is replaced with new fluid before each sampling run. Overnight chemical analysis by gas chromatography enables field personnel to know the vertical distribution of VOCs as drilling proceeds. Since its first use in 1985, the technique has successfully characterized the presence or absence of VOCs in ground water in 123 of 140 wells, many with concentrations in ground water in the low parts-per-billion range. Our sampling technique is a cost-effective and rapid method of evaluating the vertical distribution of VOCs in ground water in a complex hydrogeologic environment.     

A Single Packer Method for Characterizing Water Contributing Fractures in Crystalline Bedrock Wells

Water levels and water quality of open borehole wells in fractured bedrock are flow-weighted averages that are a function of the hydraulic heads and transmissivities of water contributing fractures, properties that are rarely known. Without such knowledge using water levels and water quality data from fractured bedrock wells to assess groundwater flow and contaminant conditions can be highly misleading. This study demonstrates a cost-effective single packer method to determine the hydraulic heads and transmissivities of water contributing fracture zones in crystalline bedrock wells. The method entails inflating a pipe plug to isolate sections of an open borehole at different depths and monitoring changes in the water level with time. At each depth, the change in water level with time was used to determine the sum of fracture transmissivities above the packer and then to solve for individual fracture transmissivity. Steady-state wellbore heads along with the transmissivities were used to determine individual fracture heads using the weighted average head equation. The method was tested in five wells in crystalline bedrock located at the University of Connecticut in Storrs. The single packer head and transmissivity results were found to agree closely with those determined using conventional logging methods and the dissolved oxygen alteration method. The method appears to be a simple and cost-effective alternative in obtaining important information on flow conditions in fractured crystalline bedrock wells.     

Isotope Approach to Assess Hydrologic Connections During Marcellus Shale Drilling

Water and gas samples were collected from (1) nine shallow groundwater aquifers overlying Marcellus Shale in north‐central West Virginia before active shale gas drilling, (2) wells producing gas from Upper Devonian sands and Middle Devonian Marcellus Shale in southwestern Pennsylvania, (3) coal‐mine water discharges in southwestern Pennsylvania, and (4) streams in southwestern Pennsylvania and north‐central West Virginia. Our preliminary results demonstrate that the oxygen and hydrogen isotope composition of water, carbon isotope composition of dissolved inorganic carbon, and carbon and hydrogen isotope compositions of methane in Upper Devonian sands and Marcellus Shale are very different compared with shallow groundwater aquifers, coal‐mine waters, and stream waters of the region. Therefore, spatiotemporal stable isotope monitoring of the different sources of water before, during, and after hydraulic fracturing can be used to identify migrations of fluids and gas from deep formations that are coincident with shale gas drilling.     

Modeling effects of multinode wells on solute transport

Long-screen wells or long open boreholes with intraborehole flow potentially provide pathways for contaminants to move from one location to another in a ground water flow system. Such wells also can perturb a flow field so that the well will not provide water samples that are representative of ground water quality a short distance away from the well. A methodology is presented to accurately and efficiently simulate solute transport in ground water systems that include wells longer than the grid spacing used in a simulation model of the system and hence are connected to multiple nodes of the grid. The methods are implemented in a MODFLOW-compatible solute-transport model and use MODFLOW's Multi-Node Well Package but are generic and can be readily implemented in other solute-transport models. For nonpumping multinode wells (used to simulate open boreholes or observation wells, for example) and for low-rate pumping wells (in which the flow between the well and the ground water system is not unidirectional), a simple routing and local mixing model was developed to calculate nodal concentrations within the borehole. For high-rate pumping multinode wells (either withdrawal or injection, in which flow between the well and the ground water system is in the same direction at all well nodes), complete and instantaneous mixing in the wellbore of all inflows is assumed.     

The Rehabilitation of Monitoring Wells Clogged by Calcite Precipitation and Drilling Mud

Based on aquifer performance tests, 13 out of 15 wells situated at the Mixed Waste Disposal (MWD) area located at the Savannah River site. South Carolina, exhibited high skin factors and low well efficiencies indicative of severely damaged wells. The use of damaged wells in aquifer testing can lead to inaccurate determinations of aquifer properties, and such wells are unusable in future remediation programs. Moreover, damaged wells can go dry during purging, thus compromising sample collection. Pump tests, chemical analyses, and biological investigations revealed that the poor well performance at MWD was attributable to calcite precipitation on the well screen and drilling mud in the filter pack. The calcite problem resulted from improper well installation, and the drilling mud in the filter pack was due to inadequate well development.
Experimental rehabilitation procedures employed on two wells, MWD 5A and 1A, included acidification, swabbing, introduction of surfactants, and surging. Treatment of the wells substantially improved well yields, skin factors, and well efficiencies. Moreover, well rehabilitation was determined to be a reasonable alternative to drilling new wells at the MWD wellfield.     

Seasonality of Coliform Bacteria Detection Rates in New Jersey Domestic Wells

It is important that indicators of fecal pollution are reliable. Coliform bacteria are a commonly used indicator of fecal pollution. As other investigators have reported elsewhere, we observed a seasonal pattern of coliform bacteria detections in domestic wells in New Jersey. Examination of a statewide database of 10 years of water quality data from 93,447 samples, from 78,207 wells, generated during real estate transactions, revealed that coliform bacteria were detected in a higher proportion of wells during warm weather months. Further examination of the seasonal pattern of other data, including well water pH, precipitation, ground and surface water temperatures, surface water coliform bacteria concentrations, and vegetation, resulted in the hypothesis that these bacteria may be derived from nonfecal (or environmentally adapted) as well as fecal sources. We provide evidence that the coliform seasonality may be the result of seasonal changes in groundwater extraction volumes (and to a lesser extent precipitation), and temperature‐driven changes in the concentration of surface or near‐surface coliform sources. Nonfecal coliform sources may not indicate the presence of fecal wastes and hence the potential presence of pathogens, or do so in an inconsistent fashion. Additional research is needed to identify the sources of the coliforms detected in groundwater.     

Numerical Modeling of the Near‐Field Hydraulics of Water Wells

Numerical flow models can be a useful tool for dimensioning water wells and to investigate the hydraulics in their near‐field. Fully laminar flow can be assumed for all models calculated up to the screen. Therefore models can be used to predict—at least qualitatively, neglecting turbulent losses inside the well—the spatial distribution of inflow into the well and the overall hydraulic performance of different combinations of aquifer parameters and technical installations. Models for both horizontal (plan view) and vertical flow (cross section) to wells were calculated for a variety of setups. For the latter, this included variations of hydraulic conductivity of the screen, pump position, and aquifer heterogeneity. Models of suction flow control devices showed that they indeed can homogenize inflow, albeit at the cost of elevated entrance losses.     

Field Investigation of a New Recharge Approach for ASR Projects in Near‐Surface Aquifers

Aquifer storage and recovery (ASR) is the artificial recharge and temporary storage of water in an aquifer when water is abundant, and recovery of all or a portion of that water when it is needed. One key limiting factor that still hinders the effectiveness of ASR is the high costs of constructing, maintaining, and operating the artificial recharge systems. Here we investigate a new recharge method for ASR in near‐surface unconsolidated aquifers that uses small‐diameter, low‐cost wells installed with direct‐push (DP) technology. The effectiveness of a DP well for ASR recharge is compared with that of a surface infiltration basin at a field site in north‐central Kansas. The performance of the surface basin was poor at the site due to the presence of a shallow continuous clay layer, identified with DP profiling methods, that constrained the downward movement of infiltrated water and significantly reduced the basin recharge capacity. The DP well penetrated through this clay layer and was able to recharge water by gravity alone at a much higher rate. Most importantly, the costs of the DP well, including both the construction and land costs, were only a small fraction of those for the infiltration basin. This low‐cost approach could significantly expand the applicability of ASR as a water resources management tool to entities with limited fiscal resources, such as many small municipalities and rural communities. The results of this investigation demonstrate the great potential of DP wells as a new recharge option for ASR projects in near‐surface unconsolidated aquifers.