Flood prediction and mitigation in coastal tourism areas,a case study: Hurghada,Egypt

Flood mitigation involves the management and control of floodwater movement, such as redirecting flood runoff through the use of floodwalls and flood gates, rather than trying to prevent floods altogether. The prevention and mitigation of flooding can be studied on three levels: on individual properties, small communities, and whole towns or cities. The current study area is located in Hurghada on the Red Sea, which is considered an important area for coastal tourism. The study area is located at distance 7.50 km from El Gouna city along the Red Sea and east of Hurghada–Al Ismaileya road. The aim of this research is to derive the runoff flow paths across the study area and their flow magnitudes under different rainfall events of 10, 25, 50, and 100 year return periods in order to design the flood mitigation measures to protect such important areas. Field data (e.g., topographic data and rainfall intensities) were collected for the study area. The results indicated that the site is exposed to high flash flood risk and protection work is required. In order to protect the area from flood risks, locations of number of drainage channels and dams were selected and designed based on flood quantity and direction. The proposed mitigation system is capable of protecting this crucial area from flood risks and increases the national income from tourism. This study can be applied in different areas of Egypt and the world.     

Iron redox dynamics in the surface waters of the Gulf of Aqaba, Red Sea

Redox transformations of iron in the surface waters of the Gulf of Aqaba, Red Sea, were studied on recurrent cruises from September 2006 to May 2007. Fe(II) concentrations and oxidation kinetics were measured in situ using luminol chemiluminescence. High Fe(II) concentrations of 200-400 pM were recorded in the autumn, followed by low concentrations of 20-130 pM in the winter-spring. A distinct diurnal pattern in Fe(II) concentrations was observed in the autumn with maximum values coinciding with maximum solar irradiance. In situ and in vitro Fe(II) oxidation rates showed temporal and spatial variability that was accounted for by changes in water temperature and pH. Dissolved oxygen was found to be the dominant oxidant in all but one cruise. In situ photoreduction rates (deduced from oxidation rates) were linearly correlated with solar irradiance during the autumn, suggesting that the reducible iron pool was not exhausted even at the strongest irradiances and that it was kept constant throughout the season. Phytoplankton had no discernible influence on Fe(II) production, consumption, or oxidation kinetics. Given the fast oxidation and photoreduction rates of up to 180 pM min⁻¹, the turn-over rates of iron were estimated at 10-30 per day. Such a dynamic Fe redox cycle probably influences the chemical reactivity and bioavailability of iron and may enhance the solubility of the abundant aerosol dust.     

Karst landform development and related sediments in the Miocene rocks of the Red Sea coastal zone,Egypt

Limestones and evaporites are the main rock types constituting the exposed Middle Miocene sediments of the Red Sea coastal zone between Quseir and Mersa Alam. These rocks represent typical conekarst and karst ridge landforms with minor surface and subsurface solution features.Mechanical, chemical and biogenic precipitates are the main recognized karst sediments. Oxides and sulphides of iron, lead and zinc and barite are also found in association with the karst features and karst products.The obtained observations elaborate the rule of the structure and lithologic characters of the country rocks and the paleoclimatic fluctuation on the formation of the karst features and the related precipitates.

---

Zusammenfassung Kalksteine und Evaporite bilden die Sedimente des Mittelmiozäns im Gebiet zwischen Quseir und Mersa Alam. Diese Gesteine zeigen charakteristische Karstphänomene, d. h., regional Kegelkarst, kleinere Karstoberflächen und unterirdische Karstformen.Klastische, chemische und biogene Sedimente werden als Karstfüllungen beobachtet. Oxide und Sulfide von Eisen, Blei und Zink sowie Baryt sind mit dem Karst und den Karstsedimenten verknüpft.Sowohl der Einflu\ der tektonischen Strukturen als auch die Zusammensetzung des mittelmiozänen Ausgangsgesteins und die paleoklimatischen Veränderungen diktieren die Entwicklung des Karstes und die Bildung der Karstsedimente.

---

Résumé Les sédiments du Miocène moyen exposés dans la région cÔtière de la Mer Rouge entre Quseir et Mersa Alam se composent essentiellement de roches calcaires et d'évaporites. Ces roches présentent des formes karstiques en cÔnes et en crètes, accompagnées de structures mineures de dissolution à la fois souterraine et de surface.Les principaux remplissages du karst sont des sédiments mécaniques, chimiques et biologiques. Des oxydes et des sulfures de fer, de plomb et de zinc, ainsi que de la barytine sont également reconnus en association avec les formes et les produits du karst.Les observations recueillies expliquent le rÔle de la structure et des caractères lithologiques des roches encaissantes, ainsi que des fluctuations paléoclimatiques sur la formation des karsts et les sédiments qui les accompagnent.

---

Quseir Mersa Alam . , . . , . , . , , . , , .

     

Heavy metals in the benthic foraminifera from the coastal lagoons,Red Sea,Egypt: indicators of anthropogenic impact on environment (case study)

Concentrations of Fe, Mn, Zn, Cu, Pb, Ni, and Cd were measured in several species and genera of Recent benthic foraminifera from three coastal lagoons, namely Abu-Shaar, Umm al-Huwaytat, and Marsa Shuni lagoons located along the Egyptian Red Sea coast. Spatially significant differences in the metal concentrations of benthic foraminifera were recorded among different sites. However, some foraminiferal species display deformation in their coiling, general shape of chambers and the apertures. Abu-Shaar and Umm al-Huwaytat lagoons are virtually influenced by anthropogenic activities while Marsa Shuni lagoon is affected by natural inputs. Benthic foraminifer shows high concentrations of Fe and Mn, especially in Umm al-Huwaytat lagoon. Foraminiferal black tests support this result and reflect selectivity for iron absorption. Among the metals analyzed, Cd, Pb, and Cu showed significant high concentrations in benthic foraminifera at the study areas. The anthropogenic activities and natural inputs are responsible for the abnormalities in benthic foraminifera. Therefore, benthic foraminifera can be used as a good indicator of the environmental changes.     

Ground-penetrating radar investigation of active faults along the Dead Sea Transform and implications for seismic hazards within the city of Aqaba, Jordan

Ground-penetrating radar (GPR) was used in an effort to locate a major active fault that traverses Aqaba City, Jordan. Measurements over an exposed (trenched) cross fault outside of the city identify a radar signature consisting of linear events and horizontal offset/flexured reflectors both showing a geometric correlation with two known faults at a control site. The asymmetric linear events are consistent with dipping planar reflectors matching the known direction of dip of the faults. However, other observations regarding this radar signature render the mechanism generating these events more complex and uncertain.GPR measurements in Aqaba City were limited to vacant lots. Seven GPR profiles were conducted approximately perpendicular to the assumed strike of the fault zone, based on regional geological evidence. A radar response very similar to that obtained over the cross fault was observed on five of the profiles in Aqaba City, although the response is weaker than that obtained at the control site. The positions of the identified responses form a near straight line with a strike of 45°. Although subsurface verification of the fault by trenching within the city is needed, the geophysical evidence for fault zone location is strong. The location of the interpreted fault zone relative to emergency services, military bases, commercial properties, and residential areas is defined to within a few meters. This study has significant implications for seismic hazard analysis in this tectonically active and heavily populated region.     

Use of electrical resistivity methods for detecting subsurface fresh and saline water and delineating their interfacial configuration: a case study of the eastern Dead Sea coastal aquifers, Jordan

The alluvial aquifer is the primary source of groundwater along the eastern Dead Sea shoreline, Jordan. Over the last 20 years, salinity has risen in some existing wells and several new wells have encountered brackish water in areas thought to contain fresh water. A good linear correlation exists between the water resistivity and the chloride concentration of groundwater and shows that the salinity is the most important factor controlling resistivity. Two-dimensional electrical tomography (ET) integrated with geoelectrical soundings were employed to delineate different water-bearing formations and the configuration of the interface between them. The present hydrological system and the related brines and interfaces are controlled by the Dead Sea base level, presently at 410 m b.s.l. Resistivity measurements show a dominant trend of decreasing resistivity (thus increasing salinity) with depth and westward towards the Dead Sea. Accordingly, three zones with different resistivity values were detected, corresponding to three different water-bearing formations: (1) strata saturated with fresh to slightly brackish groundwater; (2) a transition zone of brine mixed with fresh to brackish groundwater; (3) a water-bearing formation containing Dead Sea brine. In addition, a low resistivity unit containing brine was detected above the 1955 Dead Sea base level, which was interpreted as having remained unflushed by infiltrating rain.     

Melanesian back-arc basin and arc development: Constraints from the eastern Coral Sea

The eastern Coral Sea is a poorly explored area at the north-eastern corner of the Australian Tectonic Plate, where interaction between the Pacific and Australian plate boundaries, and accretion of the world's largest submarine plateau – the Ontong Java Plateau – has resulted in a complex assemblage of back-arc basins, island arcs, continental plateaus and volcanic products. This study combines new and existing magnetic anomaly profiles, seafloor fabric from swath bathymetry data, Ar–Ar dating of E-MORB basalts, palaeontological dating of carbonate sediments, and plate modelling from the eastern Coral Sea. Our results constrain commencement of the opening of the Santa Cruz Basin and South Rennell Trough to c. 48 Ma and termination at 25–28 Ma. Simultaneous opening of the Melanesian Basin/Solomon Sea further north suggests that a single > 2000 km long back-arc basin, with at least one triple junction existed landward of the Melanesian subduction zone from Eocene–Oligocene times. The cessation of spreading corresponds with a reorganisation of the plate boundaries in the area and the proposed initial soft collision of the Ontong Java Plateau. The correlation between back-arc basin cessation and a widespread plate reorganisation event suggests that back-arc basins may be used as markers for both local and global plate boundary changes.     

Sources,geochemical speciation,and risk assessment of metals in coastal sediments: a case study in the Bohai Sea,China

To investigate the sources and toxicity of metals in Bohai Sea sediments, concentration and geochemical speciation of metals of surface sediments were measured. Metal distributions and principal component analysis suggested that Zn, Pb, Cd, and Ag were largely derived from anthropogenic sources, whereas the majority of the other metals studied here were found to have been derived from natural rock weathering and calcareous marine biota. The major sources of anthropogenic metal inputs to the study region are from the mining industry, port transport services, vehicle exhausts, and agricultural runoff. Empirical sediment quality guidelines and the risk assessment code were used to evaluate the metal toxicities in this area. Our results show that Cd presents a high risk to the ecological system because it was found in the non-residual phase, which tends to be weakly bound and highly bioavailable; Cu, Pb, Ni, and Co pose a low risk; Zn and Cr present no risk. The use of the threshold effects level and effects range-low values of Cd and Cr as guidelines for the Bohai Sea are of limited use as they do not account for the bioavailability and toxicity of the elements in marine environments. Assessment of the annual metal fluxes from riverine and atmospheric sources indicates that the largest contributions of metals to the Bohai Sea were derived from the suspended particulate load of rivers. Furthermore, it was found that the main depositional zones for metals in the Bohai Sea were in estuaries and the center mud zones.     

Non-DRR NGOs strategies for livelihood development in the coastal communities of Bangladesh: a case study

Natural Hazards - This study aimed to assess the effectiveness of non-DRR NGOs’ programs focusing on their contribution to the uplift livelihood of the disaster-affected coastal communities....     

Synthetic impact response functions for flood vulnerability analysis and adaptation measures in coastal zones under changing climatic conditions: a case study in Gippsland coastal region,Australia

There is an increasing concern that the current management practices for many coastal regions are unsustainable. Very few countries have planned to deal with the exacerbation of environmental decline in the face of sea level rise. It is therefore necessary to assess socioeconomic and environmental impacts of sea level rises to better understand the vulnerability of coastal zones, as part of devising adaptive and integrated management principles. This paper presents a systematic approach by which relevant stakeholders can be actively engaged in prioritising flood impact issues and deriving information for quantification of impacts for adaptation measures and demonstrates the approach through implementation in the Gippsland coastal region. As outcomes of the project, we have identified key issues of concern for this region for flood impacts and constructed synthetic response functions for quantification of impacts of floods on some of the key issues in the region. The analysis also showed that stakeholders consider that some of the issues are not likely to be significantly affected by floods and thus may not require adaptation measures. The analysis did not provide high agreement on some issues. Different approaches are required to assess the importance of these issues and to establish impact response functions for them.     

The role of fluids in faulting deformation:a case study from the Dead Sea Transform (Jordan)

The geochemistry of carbonate fault rocks has been examined in two areas of the Arava Fault segment, which forms the major branch of the Dead Sea Transform between the Dead Sea and the Gulf of Aquaba. The role of fluids in faulting deformation in the selected fault segment is remarkably different from observations at other major fault zones. Our data suggest reduced fluid rock interactions in both areas and limited fluid flow. The fault did not act as an important fluid conduit. There are no indications that hydrothermal reactions (cementation, dissolution) did change the strength and behavior of the fault zone, although the two areas show considerable differences with respect to fluid sources and fluid flow. In one area, the investigated calcite mineralization reveals an open fluid system with fluids originating from a variety of sources. Stable isotopes (¹³C, ¹⁸O), strontium isotopes, and trace elements indicate both infiltration of descending (meteoric and/or sea water) and ascending hydrothermal fluids. In the other area, all geochemical data indicate only local (small scale) fluid redistribution. These fluids were derived from the adjacent limestones under nearly closed-system conditions.     

Heavy metals signature of human activities recorded in coral skeletons along the Jordanian coast of the Gulf of Aqaba, Red Sea

The concentrations of six heavy metals were studied in five living coral species and their fossil counterparts collected along the Jordanian Coast of the Gulf of Aqaba. The study aimed at investigating the validity of using coral skeletons as bioindicators for environmental pollution by heavy metals in the Gulf of Aqaba, Red Sea. The skeletal samples of the collected corals were acid digested and analyzed for Cd, Cu, Fe, Mn, Pb, and Zn content using flame atomic absorption spectrophotometer. The results obtained have shown that higher concentrations of heavy metals were found in coral skeletons from areas hosting intense developments and human activities. The massive Porites sp. coral tended to accumulate the highest metal concentrations among the other species (except for Mn). This was due to interspecific differences or selectivity of heavy metals between different coral species. It was noteworthy that fossil coral species recorded higher average metal concentrations than their living counterparts; this was attributed to surface contamination due to prolonged burial of the fossil corals in sediment over the years. The study concluded that corals (specially the massive Porites species) are vulnerable to the accumulation of high concentrations of heavy metals in their skeletons and therefore can serve as proxies to monitor environmental pollution.     

Geophysical prediction and following development sinkholes in two Dead Sea areas, Israel and Jordan

Geophysical methods—seismic refraction (SRFR), electrical resistivity tomography (ERT), and microgravity—were applied to the Dead Sea (DS) sinkhole problem in the Ein Gedi area at the earlier stage of the sinkhole development (1998–2002). They allowed determining the sinkhole formation mechanism and localizing the sinkhole hazardous zones. The SRFR method permitted to delineate the underground edge of a salt layer at the depth of 50 m. The salt edge was shaped like the sinkhole line on the surface. It was concluded that the sinkhole development is linked to the salt edge. Geoelectrical quasi-3D mapping based on the ERT technique detected large resistivity anomalies with 250–300 m² diameter and 25–35 m deep. The Ein Gedi area has been also mapped by the use of Microgravity method. The residual Bouguer gravity anomaly map shows negative anomalies arranged along the edge of the salt layer. Those gravity anomalies overall are very similar in plan to the resistivity distribution in this area. The results of forward modeling indicate that both high resistivity and residual gravity anomalies are associated with a subsurface decompaction of the soil mass and deep cavity at the sinkhole site. Following monitoring of the sinkhole development carried out by the Geological Survey of Israel confirmed our suggestions. The drilling of numerous boreholes verified the location of the salt edge. Geographical Information System (GIS) database testifies that during 2003–2009 new sinkholes are continuing to develop along the salt edge within a narrow 50–100 m wide strip oriented approximately in north–south direction (slightly parallel to the shoreline). No promotion in west–east direction (perpendicularly to the DS shoreline) was observed in Israel. Collapse of sinkholes and their clustering have been occurred within the area of high resistivity anomaly and negative residual gravity anomaly. Similar studies carried out at the Ghor Al-Haditha area (Jordan) have shown that sinkholes there are also arranged along the winding line conforming to the salt edge. In this area sinkholes are slowly moved to the Dead Sea direction. Results of geophysical studies in numerous DS sites indicate similar sinkhole development. It allowed generating of the sinkhole formation model based on ancient (10,000–11,000-year old) salt belt girding the Dead Sea along its shores     

Distribution and mode of occurrences of radionuclides in phosphogypsum from the Aqaba and Eshidiya fertilizer plants, Jordan

Phosphogypsum is a waste by-product of the phosphate fertilizer industry that has relatively high concentrations of some U decay-series radionuclides such as ^226Ra and ^210Pb. The distribution and environmental mobility of radionuclides in phosphogypsum are an important concern because this gypsum by-product is used for wallboard, in agriculture and as a soil amendment. This study determined the distribution of ^226Ra, ^210Pb, within phosphogypsum stacks of varying age and among three size fractions （coarse： 〈0.212 mm; medium： 0.212-0.053 mm; fine： 〈0.053 mm）, in phosphogypsum derived from Aqaba and Eshidiya fertilizer plants. The results indicated that ^226Ra and ^210Pb were generally uniformly distributed in phosphogypsum stacks and showed no significant difference in the concentration of these elements with the age of stack. In the Aqaba phosphogypsum ^226Ra was slightly 10% enriched in the coarse fraction, while ^210Pb was 10% enriched in the free size fraction. In the Eshidiya phosphogypsum ^226Ra and ^210Pb contents were both relatively enriched （10%） in the fine size fraction.     

Groundwater recharge zones mapping using GIS: a case study in Southern part of Jordan Valley,Jordan

This paper aims at mapping the potential groundwater recharge zones in the southern part of Jordan Valley (JV). This area is considered as the most important part for agricultural production in Jordan. The methodology adopted in this study is based on utilizing the open ended SLUGGER-DQL score model, which was developed by Raymond et al (2009). Geographic information systems were used in this study to build up the different layers of this model and to create the potential groundwater recharge zones. Based on the generated SLUGGER-DQL potential map, it was found that about 70.8 % of the investigated area was categorized as high potential for groundwater recharge, 18.7 % as moderate, and 10.5 % as low potential for groundwater recharge. To validate the model results, sensitivity analysis was carried out to assess the influence of each model parameter on the obtained results. Based on this analysis, it was found that the slope parameter (S) is the most sensitive parameter among SLUGGER-DQL model parameters, followed by water level in summer (L), well density (D), water quality (Q), runoff availability (R), land use/land cover, geology (GE), whereas the lowest sensitive parameter is the geology parameter (GE). Moreover, the parameters R, D, and Q show the lowest effective weights. The effective weight for each parameter was found to differ from the assigned theoretical weight by SLUGGER-DQL index model.     

Resource allocation for regional earthquake risk mitigation: a case study of Tehran,Iran

This paper presents a new optimization model to help cities in seismically active developing countries decide (1) How much to spend on pre-earthquake mitigation versus waiting until after an event and paying for reconstruction or simply not rebuilding damaged buildings? (2) Which buildings to mitigate and how? and (3) Which buildings to reconstruct and how? It extends previously developed optimization models to consider the particular issues that arise in such countries. First, the model allows for the possibility that some damaged buildings will not be reconstructed immediately and keeps track of any lost building inventory. Second, buildings can be mitigated to, or when damaged, reconstructed to, any appropriate structural type and seismic design level. Finally, the model objectives include minimizing the chance of an extremely high death toll in any one earthquake and minimizing the average annual death toll across earthquakes. The model is illustrated through a case study analysis for Tehran, Iran.     

Temporal and spatial distribution of dissolved Cu, Ni and Zn in the coastal waters of Jeddah, eastern Red Sea

Dissolved Cu, Ni, and Zn were measured in the surface coastal waters of Jeddah, eastern Red Sea during October 2004 and April 2005. High values of trace metals, particularly Zn, were recorded in the Southern Corniche area close to a sewage effluent indicating a significant contribution from the wastewater. Concentrations of trace metals decreased northward and southward under the effect of dilution. Another hot spot was also observed in the vicinity of Jeddah Desalination Plant (JDP) during April 2005 indicating a possible contribution from the JDP to trace metal contents in the study area. Trace metals were correlated to salinity, nutrients and particulate organic carbon (POC). The good association between Zn and reactive silicate and Ni and ammonium is attributed to simultaneous biological utilization and regeneration. The behavior of copper suggested adsorption of Cu onto the POC during October 2004 whereas in April 2005 the most important process seems to be desorption of Cu from the particulate materials.     

Assessment of vulnerability to seawater intrusion and potential remediation measures for coastal aquifers: a case study from eastern India

Seawater intrusion is a major threat to the rapidly depleting groundwater resources in the coastal areas of India. Groundwater-based irrigation, significant industrial development and rapid urbanization are some of the key contributors exacerbating the stress on groundwater resources. Vulnerability to seawater intrusion in the Ramanathapuram district of Eastern India is assessed here utilizing the GALDIT method, for a period of 10 years (2001–2010). Results revealed a drastic increase in percent area coverage under moderate vulnerability, from 19.5 to 53.88 %, between the years 2001 and 2010. On the contrary, areas classified as highly vulnerable underwent minor changes over the span of the study. Vulnerability of the study area was also analyzed for the year 2050 considering an average global mean sea level rise of 3.1 mm/year. Results from the analysis for the year 2050 showed that, almost, the entire study area (~97 %) was classified under moderate vulnerability. As a remedial measure to this imminent threat, favorable zones for artificial recharge were delineated on the basis of overlay analysis with weightage values for important controlling factors. Subsequently, the quantity of artificial recharge required to inhibit the intrusion of seawater, at specified favorable zones were estimated to be 674.87, 599.18 and 1,450.66 m³/year.     

Sedimentological and geoenvironmental evaluation of the coastal area between Al-Khowkhah and Al-Mokha,southeastern Red Sea,Republic of Yemen

The increasing anthropogenic activities (e.g., constructing touristic resorts) have led to notable changes in the Yemeni Red Sea coastal regions. In this context, recent sediments have been investigated to infer possible natural and man-induced processes on these coastal areas. The target area lies between longitudes 43°13′–43°30′E and latitudes 13°15′–13°55′N. It extends about 90 km along the coastline as a part of the Tihama plain. Geomorphologically, it forms a long-curved stretch with pronounced headlands, embayments and bays. Generally, it is covered by recent sediments (wadi, lagoon, beach and spit deposits along with sabkha, coastal dunes and mangrove). Textural studies reveal that most of the studied sediments are mainly poorly to moderately sorted and are composed mainly of sandy fractions with few gravel and mud, mostly bimodal with minor unimodal patterns. The igneous (granites) as well as basic (basalt, andesite and andesitic pyroclastics) and acidic (dacite and rhyolite) volcanic rocks of Tertiary age, which are exposed to the east of the study area, are believed to be the source of pyroxenes, amphiboles, epidotes, biotite, sphene, zircon, tourmaline and rutile, in a decreasing order of abundance. Moreover, smectite, kaolinite, chlorite, illite and palygorskite are the predominant clay minerals, mainly of detrital origin. The total carbonate content fluctuates from 37.41% (lagoon sediments) to 53.74% (sabkha sediments). The high amount of sea grasses, which covers the tidal flat zone and relates to the fine-grained sediments, accounts for the high organic matter content. The mineralogy of the source rocks has controlled the general distribution of major elements (Fe, Mg, Na, K and Mn) in the beach sediments. In such sediments, the concentrations of the heavy metals (Cu, Zn, Cd, Ni, Pb and Co) may reflect the sediment pollution using different approaches. The enrichment factors (EFs) of the trace metals for most samples reveal values that are greater than 1, referring to three groupings, which are: moderate to moderately severe (Zn, Cu and Mn), minor to moderate (Pb and Co) and zero to minor (Cd and Ni) enrichment. The EFs for Pb, Cd, Ni and Co metals (<5) may be attributed to the crustal materials and/or natural weathering processes. But, those for Zn, Cu and Mn (>5), especially in Al-Khowkhah–Abu-Zahr, Moushij–Zahari–Ruays, Yokhtol and Mokha localities, are possible of anthropogenic contributions.