Estimating bed material fluxes upstream and downstream of a controlled large bifurcation - the Mississippi-Atchafalaya River diversion

Bed material transport at river bifurcations is crucial for channel stability and downstream geomorphic dynamics. However, measurements of bed material transport at bifurcations of large alluvial rivers are difficult to make, and standard estimates based on the assumption of proportional partitioning of flow and bedload transport at bifurcations may be erroneous. In this study, we employed a combined approach based on observed topographic change (erosion/deposition) and bed material transport predicted from a one-dimensional model to investigate bed material fluxes near the engineering-controlled Mississippi-Atchafalaya River diversion, which is of great importance to sediment distribution and delivery to Louisiana's coast. Yang's (1973) sediment transport equation was utilized to estimate daily bed material loads upstream, downstream, and through the diversion during 2004–2013. Bathymetric changes in these channels were assessed with single beam data collected in 2004 and 2013. Results show that over the study period, 24% of the Mississippi River flow was diverted into the Atchafalaya River, while the rest remained in the mainstem Mississippi. Upstream of the diversion, the bed material yield was predicted to be 201 million metric tons (MT), of which approximately 35 MT (i.e., 17%) passed through the bifurcation channel to the Atchafalaya River. The findings from this study reveal that in the mainstem Mississippi, the percentage of bed material diversion (83%) is larger than the percentage of flow diversion (76%); Conversely, the diversion channel receives a disproportionate amount of flow (24%) relative to bed material supply (17%). Consequently, severe bed scouring occurred in the controlled Outflow Channel to the Atchafalaya River, while riverbed aggradation progressed in the mainstem Mississippi downstream of the diversion structures, implying reduced flow capacity and potential risk of a high backwater during megafloods. The study demonstrates that Yang's sediment transport equation provides plausible results of bed material fluxes for a highly complicated large river diversion, and that integration of the sediment transport equation with observed morphological changes in riverbed is a valuable approach to investigate sediment dynamics at controlled river bifurcations.     

A coupled hierarchical modeling approach to simulating the geomorphic response of river systems to anthropogenic climate change

Anthropogenic climate change is expected to change the discharge and sediment transport regime of river systems. Because rivers adjust their channels to accommodate their typical inputs of water and sediment, changes in these variables can potentially alter river morphology. In this study, a hierarchical modeling approach was developed and applied to examine potential changes in reach‐averaged bedload transport and spatial patterns of erosion and deposition for three snowmelt‐dominated gravel‐bed rivers in the interior Pacific Northwest. The modeling hierarchy was based on discharge and suspended‐sediment load from a basin‐scale hydrologic model driven by a range of downscaled climate‐change scenarios. In the field, channel morphology and sediment grain‐size data for all three rivers were collected. Changes in reach‐averaged bedload transport were estimated using the Bedload Assessment of Gravel‐bedded Streams (BAGS) software, and the Cellular Automaton Evolutionary Slope and River (CAESAR) model was used to simulate the spatial pattern of erosion and deposition within each reach to infer potential changes in channel geometry and planform. The duration of critical discharge was found to control bedload transport. Changes in channel geometry were simulated for the two higher‐energy river reaches, but no significant morphological changes were found for a lower‐energy reach with steep, cohesive banks. Changes in sediment transport and river morphology resulting from climate change could affect the management of river systems for human and ecological uses. Copyright © 2015 John Wiley & Sons, Ltd.     

Sediment dynamics and temporal variation of runoff in the Yom River,Thailand

The Yom River is one of the four major sediment sources to the Chao Phraya River in Thailand. Human activities and changes in climate over the past six decades may have affected the discharge and sediment load to some extent. In the current study, the river discharge and sediment characteristics in the mainstream of the Yom River were investigated using the field observation data from 2011 to 2013 and the historical river flow and sediment data from 1954 to 2014 at six hydrological stations operated by the Royal Irrigation Department of Thailand (RID). The non-parametric Mann-Kendall test and double mass curve were used to analyze the sediment dynamics and temporal changes in the discharge of the Yom River. The results revealed that the sediment was mainly transported in suspension, and the bed-to-suspended sediment loads ratio varied between 0 and 0.05. The daily suspended sediment load (SSL) in the upper and middle basins had a strong correlation with the daily discharge and could be represented by power equations with coefficients of determination higher than 0.8. The daily suspended sediment load in the lower basin did not directly depend on the corresponding discharge because of the reduction in river slope and water diversion by irrigation projects. It also appeared that the river discharges and sediment loads were mainly influenced by climate variation (floods and droughts). Moreover, the average sediment transport of the upper, middle, and lower reaches were 0.57, 0.71, and 0.35 million t/y, respectively. The sediment load in the lower basin decreased more than 50% as a result of changes in the river gradient (from mountainous to floodplain areas). The results from sediment analysis also indicated that the construction of the Mae Yom Barrage, the longest diversion dam in Thailand, and land-use changes did not significantly affect the sediment load along the Yom River.     

THREE DIMENSIONAL NUMERICAL MODELLING OF FLOW AND SEDIMENT TRANSPORT IN RIVERS

The 3D numerical model, ECOMSED (open source code), was used to simulate flow and sediment transport in rivers. The model has a long history of successful applications to oceanic, coastal and estuarine waters. Improvements in the advection scheme, treatment of river roughness parameterization and shear stress partitioning were necessary to reproduce realistic and comparable results in a river application. To account for the dynamics of the mobile bed boundary, a model for the bed load transport was included in the code. The model reproduced observed secondary currents, bed shear stress distribution and erosion-deposition patterns on a curved channel. The model also successfully predicted the general flow patterns and sediment transport characteristics of a 1-km long reach of the River Klar?lven, located in the north of the county of V?rmland, Sweden.     

Peak discharge increase in hyperconcentrated floods

The peak of river floods usually decreases in the downstream direction unless it is compensated by freshwater inflow from tributaries. In the Yellow River (China) the opposite is regularly observed, where the peak discharge of river floods increases in the downstream direction (at a rate far exceeding the contribution from tributaries). This flood peak discharge increase is probably related to rapid morphological changes, to a modified bed friction, or to a combination of both. Yet the relative role of these processes is still poorly understood. This paper aims to analyze the relative contribution of bed erosion and friction change to the peak discharge increase, based on available data and a recently developed numerical model. Using this high-resolution, fully coupled morphodynamic model of non-capacity sediment transport, two hyperconcentrated floods characterized by downstream peak discharge increase are numerically reproduced and analyzed in detail. The results reveal that although erosion effects may contribute to the downstream discharge increase (especially in case of extreme erosion), for most cases the increase must be mainly due to a reduction in bed friction during peak discharge conditions. Additionally, based on the concept of channel storage reduction, the effects of decreasing bed friction and (very strong) bed erosion can be integrated in explaining the peak discharge increase.     

2D NUMERICAL SIMULATION OF FLOOD AND FLUVIAL PROCESS IN THE MEANDERING AND ISLAND-BRAIDED MIDDLE YANGTZE RIVER

The characteristics of water flow and sediment transport in a typical meandering and island-braided reach of the middle Yangtze River is investigated using a two-dimensional （2D） mathematical model. The major problems studied in the paper include the carrying capacity for suspended load, the incipient velocity and transport formula of non-uniform sediment, the thickness of the mixed layer on the riverbed, and the partitioning of bed load and suspended load. The model parameters are calibrated using extensive field data. Water surface profiles, distribution of flow velocities, riverbed deformation are verified with site measurements. The model is applied to a meandering and island-braided section of the Wakouzi-Majiazui reach in the middle Yangtze River, which is about 200 km downstream from the Three Gorges Dam, to study the training scheme of the navigation channels. The model predicts the processes of sediment deposition and fiver bed erosion, changes of flow stage and navigation conditions for the first 20 years of impoundment of the Three Gorges Project.     

Significance of particle interaction to the modelling of cohesive sediment transport in rivers

Aggregation processes of fine sediments have rarely been integrated in numerical simulations of cohesive sediment transport in riverine systems. These processes, however, can significantly alter the hydrodynamic characteristics of suspended particulate matter (SPM), modifying the particle settling velocity, which is one of the most important parameters in modelling suspended sediment dynamics. The present paper presents data from field measurements and an approach to integrate particle aggregation in a hydrodynamic sediment transport model. The aggregation term used represents the interaction of multiple sediment classes (fractions) with corresponding multiple deposition behaviour. The k–ε–turbulence model was used to calculate the coefficient of vertical turbulent mixing needed for the two‐dimensional vertical‐plane simulations. The model has been applied to transport and deposition of tracer particles and natural SPM in a lake‐outlet lowland river (Spree River, Germany). The results of simulations were evaluated by comparison with field data obtained for two levels of river discharge. Experimental data for both discharge levels showed that under the prevailing uniform hydraulic conditions along the river reach, the settling velocity distribution did not change significantly downstream, whereas the amount of SPM declined. It was also shown that higher flow velocities (higher fluid shear) resulted in higher proportions of fast settling SPM fractions. We conclude that in accordance with the respective prevailing turbulence structures, typical aggregation mechanisms occur that continuously generate similar distribution patterns, including particles that settle toward the river bed and thus mainly contribute to the observed decline in the total SPM concentration. In order to determine time‐scales of aggregation and related mass fluxes between the settling velocity fractions, results of model simulations were fitted to experimental data for total SPM concentration and of settling velocity frequency distributions. The comparison with simulations for the case of non‐interacting fractions clearly demonstrated the practical significance of particle interaction for a more realistic modelling of cohesive sediment and contaminant transport. Copyright © 2004 John Wiley & Sons, Ltd.     

One-dimensional numerical simulation of non-uniform sediment transport under unsteady flows

One-dimensional numerical models are popularly used in sediment transport research because they can be easily programmed and cost less time compared with two- and three-dimensional numerical models. In particular, they possess greater capacity to be applied in large river basins with many tributaries. This paper presents a one-dimensional numerical model capable of calculating total-load sediment transport. The cross-section-averaged sediment transport capacity and recovery coefficient are addressed in the suspended load model. This one-dimensional model, therefore, can be applied to fine suspended loads and to hyperconcentrated flows in the Yellow River. Moreover, a new discretization scheme for the equation of unsteady non-uniform suspended sediment transport is proposed. The model is calibrated using data measured from the Yantan Reservoir on the Hongshui River and the Sanmenxia Reservoir on the Yellow River. A comparison of the calculated water level and river bed deformation with field measurements Shows that the improved numerical model is capable of predicting flow, sediment transport, bed changes, and bed-material sorting in various situations, with reasonable accuracy and reliability.     

Bedform effect on the reorganization of surface and subsurface grain size distribution in gravel bedded channels

Quantification of river bedform variability and complexity is important for sediment transport modeling as well as for characterization of river morphology. Alluvial bedforms are shown to exhibit highly nonlinear dynamics across a range of scales, affect local bed roughness, and vary with local hydraulic, hydrologic, and geomorphic properties. This paper examines sediment sorting on the crest and trough of gravel bedforms and relates it to bed elevation statistics. The data analysed here are the spatial and temporal series of bed elevation, grain size distribution of surface and subsurface bed materials, and sediment transport rates from flume experiments. We describe surface topography through bedform variability in height and wavelength and multiscale analysis of bed elevations as a function of discharge. We further relate bedform migration to preferential distribution of coarse and fine sediments on the troughs and crests, respectively, measuring directly surface and subsurface grain size distributions, and indirectly the small scale roughness variations as estimated from high resolution topographic scans.     

Modelling of meander migration in an incised channel

An updated linear computer model for meandering rivers with incision has been developed. The model simulates the bed topography, flow field, and bank erosion rate in an incised meandering channel. In a scenario where the upstream sediment load decreases （e.g., after dam closure or soil conservation）, alluvial river experiences cross section deepening and slope flattening. The channel migration rate might be affected in two ways： decreased channel slope and steeped bank height. The proposed numerical model combines the traditional one-dimensional （1D） sediment transport model in simulating the channel erosion and the linear model for channel meandering. A non-equilibrium sediment transport model is used to update the channel bed elevation and gradations. A linear meandering model was used to calculate the channel alignment and bank erosion/accretion, which in turn was used by the 1D sediment transport model. In the 1D sediment transport model, the channel bed elevation and gradations are represented in each channel cross section. In the meandering model, the bed elevation and gradations are stored in two dimensional （2D） cells to represent the channel and terrain properties （elevation and gradation）. A new method is proposed to exchange information regarding bed elevations and bed material fractions between 1D river geometry and 2D channel and terrain. The ability of the model is demonstrated using the simulation of the laboratory channel migration of Friedkin in which channel incision occurs at the upstream end.     

Rapid changes of sediment dynamic processes in Yalu River Estuary under anthropogenic impacts

The response of the Yalu River Estuary to human activities was investigated.Changes of sediment dynamics during the past 10 years were explored through hydrodynamic calculation,as well as heavy mineral...     

Sediment mobility and bed armoring in the St Clair River: insights from hydrodynamic modeling

The lake levels in Lake Michigan‐Huron have recently fallen to near historical lows, as has the elevation difference between Lake Michigan‐Huron compared to Lake Erie. This decline in lake levels has the potential to cause detrimental impacts on the lake ecosystems, together with social and economic impacts on communities in the entire Great Lakes region. Results from past work suggest that morphological changes in the St Clair River, which is the only natural outlet for Lake Michigan‐Huron, could be an appreciable factor in the recent trends of lake level decline. A key research question is whether bed erosion within the river has caused an increase in water conveyance, therefore, contributed to the falling lake level. In this paper, a numerical modeling approach with field data is used to investigate the possibility of sediment movement in the St Clair River and assess the likelihood of morphological change under the current flow regime. A two‐dimensional numerical model was used to study flow structure, bed shear stress, and sediment mobility/armoring over a range of flow discharges. Boundary conditions for the numerical model were provided by detailed field measurements that included high‐resolution bathymetry and three‐dimensional flow velocities. The results indicate that, without considering other effects, under the current range of flow conditions, the shear stresses produced by the river flow are too low to transport most of the coarse bed sediment within the reach and are too low to cause substantial bed erosion or bed scour. However, the detailed maps of the bed show mobile bedforms in the upper St Clair River that are indicative of sediment transport. Relatively high shear stresses near a constriction at the upstream end of the river and at channel bends could cause local scour and deposition. Ship‐induced propeller wake erosion also is a likely cause of sediment movement in the entire reach. Other factors that may promote sediment movement, such as ice cover and dredging in the lower river, require further investigation. Copyright © 2012 John Wiley & Sons, Ltd.     

Graded and uniform bed load sediment transport in a degrading channel

Twenty runs of experiments are carried out to investigate non-equilibrium transport of graded and uniform bed load sediment in a degrading channel. Well-sorted gravel and sand are employed to compose four kinds of sediment beds with different gravel/sand contents, i.e., uniform 100%gravel bed, uniform 100% sand bed, and two graded sediment beds respectively with 53% gravel and 47% sand as well as 22%gravel and 78%sand. For different sediment beds, the experiments are conducted under the same discharges, thereby allowing for the role of sediment composition in dictating the bed load transport rate to be identified. A new observed dataset is generated concerning the flow, sediment transport and evolution of bed elevation and composition, which can be exploited to underpin devel-opments of mathematical river models. The data shows that in a degrading channel, the sand greatly promotes the transport of gravel, whilst the gravel considerably hinders the transport of sand. The promoting and hindering effects are evaluated by means of impact factors defined based on sediment transport rates. The impact factors are shown to vary with flow discharge by orders of magnitude, being most pronounced at the lowest discharge. It is characterized that variations in sand or gravel inputs as a result of human activities and climate change may lead to severe morphological changes in degrading channels.     

Width control on event-scale deposition and evacuation of sediment in bedrock-confined channels

In mixed bedrock–alluvial rivers, the response of the system to a flood event can be affected by a number of factors, including coarse sediment availability in the channel, sediment supply from the hillslopes and upstream, flood sequencing and coarse sediment grain size distribution. However, the impact of along-stream changes in channel width on bedload transport dynamics remains largely unexplored. We combine field data, theory and numerical modelling to address this gap. First, we present observations from the Daan River gorge in western Taiwan, where the river flows through a 1 km long 20–50 m wide bedrock gorge bounded upstream and downstream by wide braidplains. We documented two flood events during which coarse sediment evacuation and redeposition appear to cause changes of up to several metres in channel bed elevation. Motivated by this case study, we examined the relationships between discharge, channel width and bedload transport capacity, and show that for a given slope narrow channels transport bedload more efficiently than wide ones at low discharges, whereas wider channels are more efficient at high discharges. We used the model sedFlow to explore this effect, running a random sequence of floods through a channel with a narrow gorge section bounded upstream and downstream by wider reaches. Channel response to imposed floods is complex, as high and low discharges drive different spatial patterns of erosion and deposition, and the channel may experience both of these regimes during the peak and recession periods of each flood. Our modelling suggests that width differences alone can drive substantial variations in sediment flux and bed response, without the need for variations in sediment supply or mobility. The fluctuations in sediment transport rates that result from width variations can lead to intermittent bed exposure, driving incision in different segments of the channel during different portions of the hydrograph. © 2020 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd     

Nonlinearity and complexity in gravel bed dynamics

The dynamics of river bed evolution are known to be notoriously complex affected by near-bed turbulence, the collective motion of clusters of particles of different sizes, and the formation of bedforms and other large-scale features. In this paper, we present the results of a study aiming to quantify the inherent nonlinearity and complexity in gravel bed dynamics. The data analyzed are bed elevation fluctuations collected via submersible sonar transducers at 0.1 Hz frequency in two different settings of low and high discharge in a controlled laboratory experiment. We employed surrogate series analysis and the transportation distance metric in the phase-space to test for nonlinearity and the finite size Lyapunov exponent (FSLE) methodology to test for complexity. Our analysis documents linearity and underlying dynamics similar to that of deterministic diffusion for bed elevations at low discharge conditions. These dynamics transit to a pronounced nonlinearity and more complexity for high discharge, akin to that of a multiplicative cascading process used to characterize fully developed turbulence. Knowing the degree of nonlinearity and complexity in the temporal dynamics of bed elevation fluctuations can provide insight into model formulation and also into the feedbacks between near-bed turbulence, sediment transport and bedform development.     

A MATHEMATICAL MODEL FOR RESERVOIR SEDIMENTATION AND FLUVIAL PROCESSES

I. INTRODUCTIONAt present moot sediment transport models applied in engineering practice are based on equilibriumsediment transport approach, i. e. sediment--carrying Capacity is used to replace the actual sediment concentration (ref. 1 -- 9). However, the sediment--carrying capacity, in general, is not equal to sedimentconcentration, they may differ a lot especially for the case of reservoir sedimentation process and/orthe scouring process of river channel in the downstream of a reservoi…     

Climatic and anthropogenic impacts on the decrease of sediment discharge to the Mediterranean coast from the largest river of Maghreb

The current study focuses on the issue of the decrease in sediment discharge to the Mediterranean Sea by the largest river in Algeria,the Wadi Cheliff(i.e.Cheliff River).This study clarifies the effect of climatic and anthropogenic factors on the changes in the sedimentary dynamics of the Cheliff River discharging to the sea.The data used(rainfall,water discharge,and sediment discharge)concern the Sidi Bel Attar gaging station on the Cheliff River,only 18 km from discharge to the Mediterranean Sea.A power-type statistical regression model was used to fill the 74.2% gap in Suspended Solids(SS)measurements in the establishment of a SS database for the period 1951e2012.The study results show that the transport of suspended sediment discharged to the sea is about 487 t/km^2/yr.Statistical tests of breaks highlight that rainfall decreased by 26% and that water and sediment input to the sea declined from 74%to 63% for the period of 1981e2012.The correlation analysis shows a decrease in the contribution of rainfall on sediment and water input at the outlet equal to 77.9% and 77.8%,respectively,during the period of 1980 e2012,compared to the period of 1968e1980.However,the double mass method reflects the contribution of factors other than rainfall to the decrease of sediment input to the sea.These other factors mainly include large dams,which intercepted about 71%of the total volume of sediment discharged to the sea during the period of 1968e2010.In addition the contribution of large dams to the reduction of sedimentary input to the sea is more important than that of the decrease in rainfall.The management of large dams also contributes to the increase in the sediment deficit to the sea through the prioritization of interception of sediment at the expense of releases,for socio-economic purposes,68.4%of the Cheliff River discharge is diverted for human use.This has led to an increase in the mean water bed level at bankfull downstream,where the Cheliff River gave up 51%of its width to the floodplain between 1996 and 2009.In the light of the scarcity of sediment transport data in North Africa and in many other areas,the current study provides a reference framework for other studies:providing useful information for the study of the transfer of sediment from land to sea,and the links with the socio-economic needs.     

Response of A Gravel - Bed River To Dam Closure: Insights From Sediment Transport Processes And Channel Morphodynamics

This work deals with the impacts of dams on large gravel -bed rivers in terms of altering coarse transport regimes and the relationship with river morphodynamics. Using data collected by a tracer -based monitoring programme carried out in a 4 -km -long study sector of the Parma River (Italy), located downstream from a relatively recently established dam, we applied a virtual velocity approach to estimate the coarse bed material load at four river cross -sections. Monitoring and calculation results provided new insights into the impacts of the dam on streambed material mobility and the sediment regime over the 17 -month calculation period. A longitudinal gradient of effects was observed along the study sector. Sections located closer to the dam are characterized by more evident impacts due to deficits in coarse sediment input from upstream. Sediment mobility here is strongly altered, especially in the highly armoured main channel, and the overall bed material load is extremely low. A partial recovery of sediment dynamics was observed at the sections located further from the dam, where estimates indicate higher sediment yield. The observed longitudinal trend in the coarse sediment transport regime matches the morphology, as the river shifts downstream from a sinuous configuration with alternate bars to a wandering one. The novel insights into alteration of coarse sediment dynamics and the relationship with river morphodynamics are potentially applicable to many other fluvial contexts affected by similar impoundments. © 2019 John Wiley & Sons, Ltd.     

Insights into bedload transport processes of a large regulated gravel‐bed river

A comprehensive monitoring programme focusing on bedload transport behaviour was conducted at a large gravel‐bed river. Innovative monitoring strategies were developed during five years of preconstruction observations accompanying a restoration project. A bedload basket sampler was used to perform 55 cross‐sectional measurements, which cover the entire water discharge spectrum from a 200‐year flood event in 2013 to a rare low flow event. The monitoring activities provide essential knowledge regarding bedload transport processes in large rivers. We have identified the initiation of motion under low flow conditions and a decrease in the rate of bedload discharge with increasing water discharge around bankfull conditions. Bedload flux strongly increases again during high flood events when the entire inundation area is flooded. No bedload hysteresis was observed. The effective discharge for bedload transport was determined to be near mean flow conditions, which is therefore at a lower flow discharge than expected. A numerical sediment transport model was able to reproduce the measured sediment transport patterns. The unique dataset enables the characterisation of bedload transport patterns in a large and regulated gravel‐bed river, evaluation of modern river engineering measures on the Danube, and, as a pilot project has recently been under construction, is able to address ongoing river bed incision, unsatisfactory ecological conditions for the adjacent national park and insufficient water depths for inland navigation. Copyright © 2017 John Wiley & Sons, Ltd.     

Uniform and graded bed-load sediment transport in a degrading channel with non-equilibrium conditions

Bed-load transport plays a critical role in river morphological change and has an important impact on river ecology.Although there is good understanding of the role of the variation of river bed grain size on transport dynamics in equilibrium conditions,much less is understood for non-equilibrium conditions when the channel is either aggrading or degrading.In particular,the relative role of different grain sizes in the promotion and hindering of the transport of coarse and fine fractions in a degrading channel has yet to be investigated.The current study attempts to provide new understanding through a series of flume experiments done using uniform and graded sediment particles.The experiments revealed coarser grain-size fractions for a poorly-sorted sediment,relative to uniform-sized sediment,reduced the transport of finer grains and finer fractions enhanced the transport of coarse grains.This hinderingpromotion effect,caused by relative hiding and exposure of finer and coarse fractions,increased with bed slope and decreased with relative submergence.In particular,as relative submergence increased,the graded fractions tended towards behaving more like their unifo rm-sized counterparts.Also,the bed-load parameter of the graded fractions increased more with a rise in bed slope than observed for the uniformsized counterparts.These results revealed,for degrading channel conditions,such as downstream of a dam,bed-load equations developed for uniform bed sediment are inappropriate for use in natural river systems,particularly in mountain streams.Furthermore,changes in river bed composition due to activities that enhance the input of hill-slope sediment,such as fire,logging,and agricultural development,are likely to cause significant changes in river morphology.