OWC wave energy devices with air flow control

A theoretical model is developed to simulate the energy conversion, from wave to turbine shaft, of an oscillating-water-column (OWC) plant equipped with a Wells air-turbine and with a valve (in series or in parallel with the turbine) for air-flow control. Numerical simulations show that the use of a control valve, by preventing or reducing the aerodynamic stall losses at the turbine rotor blades, may provide a way of substantially increasing the amount of energy produced by the plant, particularly at the higher incident wave power levels. From the hydrodynamic point of view, a by-pass valve or a throttle valve should be used depending on whether the wave energy absorbing system is over-damped or under-damped by the turbine.     

Stochastic modelling in wave power-equipment optimization: maximum energy production versus maximum profit

The paper presents an optimization study for the mechanical and electrical equipment of an oscillating-water-column (OWC) wave power plant of fixed shoreline or nearshore type, equipped with an air turbine. The plant’s structure geometry is assumed to be given and the corresponding hydrodynamic coefficients are known as functions of wave frequency. A stochastic model is adopted for the energy conversion process from wave to air turbine, it being assumed that the system is linear. The optimization concerns the turbine size, represented by its rotor diameter D. Two alternative criteria are used: (i) maximization of the produced electrical energy, (ii) maximization of the annual profit. An example calculation is presented, based on the hydrodynamic coefficients of the OWC on the island of Pico, Azores, and on the aerodynamic performance curves of its Wells turbine. The influence of the following parameters upon optimized turbine size and rated power output is analyzed: wave climate, capital costs of mechanical and electrical equipment, operation and maintenance costs, discount rate, equipment lifetime and price of electrical energy supplied to the grid.     

Numerical modeling of a wave energy converter based on U-shaped interior oscillating water column

The paper presents a concept of a wave energy converter and the numerical model to calculate the hydrodynamic responses in waves and the power produced by the power take off system. The system consists of an asymmetric floater with an interior U-tank partially filled with water and two lateral air chambers connected by a duct. The motion of the U-shaped oscillating water column, mainly induced by the rolling of the floater, forces the air through the duct where a Wells turbine is installed to absorb the wave energy.The wave-floater hydrodynamics is calculated with a Green's function panel method, while the oscillating water column motions hydro-mechanics are derived from the one-dimensional Euler's equation. The dynamics of the Wells turbine is realistically represented by one additional differential equation on the unknown air pressure fluctuation. This equation is derived assuming small amplitude motions of the water column and assuming the linear isentropic relation is valid for the air thermodynamics in the air chambers. The Wells turbine is characterized by a drastic drop of efficiency above a critical pressure value due to stalling on the blades. The effect of a by-pass valve to prevent stalling is introduced in the numerical model in a simplistic way. The numerical model is implemented and tested for a wave energy converter with a displacement of 1150 t, including 490 t for the interior water column, and an installed turbine with 2.3 m of diameter. An analysis of the influence of changing different design parameters on the system efficiency is also presented.     

Wave power extraction from an oscillating water column along a straight coast

In order to study the effects of coastline on wave power absorption, we describe here a linearized theory of an oscillating water column (OWC) installed on a straight coast. The sea depth is assumed to be constant and the coast is a vertical cliff. The column is a vertical circular cylinder half embedded in the cliff and open on the seaside. Forced by incident waves from any direction, the water surface inside pushes the dry air above through a Wells turbine system to generate power. Carrying out the linearized theories of radiation and diffraction analytically, we calculate the coefficients of apparent mass and radiation damping, and the chamber pressure. Optimum absorption efficiency is examined under the constraint of constant chamber volume. Results are compared with a parallel study of an OWC installed either offshore or at the tip of a thin breakwater.     

Effects of Rotor Solidity on the Performance of Impulse Turbine for OWC Wave Energy Converter

Impulse turbine, working as a typical self-rectifying turbine, is recently utilized for the oscillating water column (OWC) wave energy converters, which can rotate in the same direction under the bi-directional air flows. A numerical model established in Fluent is validated by the corresponding experimental results. The flow fields, pressure distribution and dimensionless evaluating coefficients can be calculated and analyzed. Effects of the rotor solidity varying with the change of blade number are investigated and the suitable solidity value is recommended for different flow coefficients.     

Efficiency of OWC wave energy converters: A virtual laboratory

The performance of an oscillating water column (OWC) wave energy converter depends on many factors, such as the wave conditions, the tidal level and the coupling between the chamber and the air turbine. So far most studies have focused on either the chamber or the turbine, and in some cases the influence of the tidal level has not been dealt with properly. In this work a novel approach is presented that takes into account all these factors. Its objective is to develop a virtual laboratory which enables to determine the pneumatic efficiency of a given OWC working under specific conditions of incident waves (wave height and period), tidal level and turbine damping. The pneumatic efficiency, or efficiency of the OWC chamber, is quantified by means of the capture factor, i.e. the ratio between the absorbed pneumatic power and the available wave energy. The approach is based on artificial intelligence—in particular, artificial neural networks (ANNs). The neural network architecture is chosen through a comparative study involving 18 options. The ANN model is trained and, eventually, validated based on an extensive campaign of physical model tests carried out under different wave conditions, tidal levels and values of the damping coefficient, representing turbines of different specifications. The results show excellent agreement between the ANN model and the experimental campaign. In conclusion, the new model constitutes a virtual laboratory that enables to determine the capture factor of an OWC under given wave conditions, tidal levels and values of turbine damping, at a lower cost and in less time than would be required for conventional laboratory tests.     

Effect of reciprocating and unidirectional airflow on primary conversion of a pentagonal Backward Bent Duct Buoy

An Oscillating Water Column (OWC) device can output energy through reciprocating or unidirectional airflow. The unidirectional airflow is helpful to utilize a simple and high-efficiency unidirectional air turbine. The pentagonal BBDB proposed by us based on OWC principle can be regarded as a floating Oscillating Body and its Power Take-Off (PTO) consists of a chamber, a water column, a turbine and a generator. The Capture Width Ratio (CWR) of the pentagonal BBDB model with the reciprocating and unidirectional airflow was studied in this paper. The wave flume test results indicate the mean CWR of the pentagonal BBDB model with reciprocating airflow can reach up to 121.91% and the mean CWR of the model with unidirectional airflow could reach 100.94% during the whole wave cycle in regular waves. For irregular waves, the mean CWR of the model with the unidirectional airflow is as high as 62.83% during the whole wave cycle. Hopefully, the combination of the pentagonal BBDB with the check valve to output power during the air exhalation and conventional high-efficiency unidirectional turbine will improve the total efficiency of the BBDB.     

Numerical Simulation and Experimental Investigation on Performance of the Wells Turbine in Irregular Oscillating Flow

The Wells turbine is an axial-flow air-turbine designed to extract energy from ocean waves. An important consideration is the self-starting capability of the Wells turbine, a phenomenon encountered where the turbine accelerate by itself up to a certain speed for the best turbine performance. In order to clarify the self-starting characteristic and running performance of the Wells turbine in an irregular oscillating flow, a numerical simulation process is established in this paper on the rational assumption of quasi-steady flow conditions. Both self-starting characteristics and running performance are obtained through the numerical simulation and subsequently compared with the experimental data achieved on a computer-controlled oscillating flow test rig which could realize some irregular oscillating flow according to the specified spectrum. Results show that the self-starting time decreases with the increase of the significant wave height and the mean frequency of the irregular oscillating flow. Therefor     

Experimental study of the hydrodynamic performance of an onshore wave power device in the presence of an underwater mound

The hydrodynamic functioning of an oscillating water column (OWC) in the presence of an underwater tri-dimensional mound (UTDM) through large-scale ocean engineering basin experiments is described. Experiments are carried out with both regular and irregular waves and are compared to numerical models. The analysis is based on the measurements of the wave amplification in the water column for the OWC performance and on surface deformation upwave and over the UTDM for the wave transformation due to both UTDM and OWC. A significant increase of the capture-width ratio due to wave focusing above the mound is observed experimentally. This wave focusing is also well described numerically with a refraction–diffraction model. The wave amplification in the water column for both regular and irregular waves is compared to results from a linear potential model based on an integral matching method. Linear behaviour of the hydrodynamic response of the device is verified for both open and partially closed conditions, in particular for irregular waves.     

On the tuning of a wave-energy driven oscillating-water-column seawater pump to polychromatic waves

Performance of wave-energy devices of the oscillating water column (OWC) type is greatly enhanced when a resonant condition with the forcing waves is maintained. The natural frequency of such systems can in general be tuned to resonate with a given wave forcing frequency. In this paper we address the tuning of an OWC sea-water pump to polychromatic waves. We report results of wave tank experiments, which were conducted with a scale model of the pump. Also, a numerical solution for the pump equations, which were proven in previous work to successfully describe its behavior when driven by monochromatic waves, is tested with various polychromatic wave spectra. Results of the numerical model forced by the wave trains measured in the wave tank experiments are used to develop a tuning criterion for the sea-water pump.     

Experimental Study on Conversion Efficiency of A Floating OWC Pentagonal Backward Bent Duct Buoy Wave Energy Converter

Wave tank tests were carried out to evaluate the total efficiency of a floating OWC Pentagonal Backward Bent Duct Buoy (PBBDB). Two kinds of turbine generators were used in tests. The incident wave power, pneumatic power and electricity were measured. The test results show that the primary efficiency can reach up to 185.98% in regular waves and 85.86% in irregular waves. The total efficiency from wave to wire with Wells turbine-generator set is 33.43% in regular waves and 15.82% in irregular waves. The peak total efficiency of the PBBDB with check valves equipped with the impulse turbine-generator set is 41.68% in regular waves and 27.10% in irregular waves. The efficiency of the turbine-generator set is about 30% in the tests. Obviously, the total efficiency can be further improved with the increasing of turbine efficiency.     

基于VOF模型的OWC气室波浪场数值分析

近年来,振荡水柱形式在波能转换装置中得到了广泛应用,由于波况不同,需对气室加以研究并对其形状参量进行优化,从而使空气流速和能量转换达到最大值.利用基于VOF模型建立二维数值波浪水槽,将数值计算的振荡水柱在气室内的升沉运动与物理模型试验进行比较,验证其正确性,并将OWC气室的研究手段予以推广.     

Wells turbine with end plates for wave energy conversion

In order to improve the performance of the Wells turbine for wave energy conversion, the effect of end plate on the turbine characteristics has been investigated experimentally by model testing. As a result, it is found that the characteristics of the Wells turbine with end plates are superior to those of the original Wells turbine, i.e., the turbine without end plate and the characteristics are dependent on the size and position of end plate. Furthermore, by using a computational fluid dynamics (CFD), reason of the performance improvement of the turbine has been clarified and the effectiveness of the end plate has been demonstrated.     

Self-Starting Analysis of an OWC Axial Impulse Turbine in Constant Flows: Experimental and Numerical Studies

In recent times, self-rectifying axial-flow air turbines are being widely employed in oscillating water column (OWC) wave energy converters (WEC). The steady performance of air turbines has been systematically investigated in previous studies. However, there still exists a lack of information on their unsteady performance, such as in the self-starting characteristics and subsequent running behavior. In this study, the unsteady behavior of impulse turbine under various constant-flow conditions is investigated. Experimental studies were conducted to investigate the effects of constant-load on the variations in the rotation speed, the pressure drop and the torque output of the turbine starting from rest. A fully passive flow-driving numerical model is employed for further detailed analysis of the flow and pressure fields. Followed by a well-agreed validation using the corresponding experimental data, the three dimensional (3D) transient model is used to study the effects of the air-flow velocity magnitude and the rotors’ moment of inertia on the self-starting performance of the turbine. Except for the variations in the rotation speed, the pressure drop and the pneumatic torque, the distributions of the flow-field and the pressure over the blades at specific time-points are analyzed.     

Numerical study of air chamber for oscillating water column wave energy convertor

Oscillating Water Column (OWC) wave energy converting system is one of the most widely used facilities all over the world.The air chamber is utilized to convert the wave energy into the pneumatic energy.The numerical wave tank based on the two-phase VOF model is established in the present study to investigate the operating performance of OWC air chamber.The RANS equations,standard k-ε turbulence model and dynamic mesh technology are employed in the numerical model.The effects of incident wave conditions and shape parameters on the wave energy converting efficiency are studied and the capability of the present numerical wave tank on the corresponding engineering application is validated.     

振荡水柱波能装置冲击式空气透平优化数值模拟研究

冲击式空气透平是振荡水柱式波能发电装置的二级能量转换装置,具有自启动性能好、在大流量系数区保持较高效率等优势,近年来应用越来越广泛.有学者提出在冲击式透平动叶片尖端安装环结构的设计,可以改善动叶片叶尖间隙处的气流流动形态,提高透平的工作性能.依托于此观点,构建了安装有环结构的冲击式透平的三维定常数值模型,并通过网格数量...     

3D hydrodynamic modelling of fixed oscillating water column wave power plant by a boundary element methods

A three-dimensional (3D) numerical model of fixed Oscillating Water Column system (OWC) is presented and validated. The steady-state potential flow boundary value problem due to regular wave interaction with the OWC is solved by a first order mixed distribution panel method. Ocean response predictions are derived using a deterministic statistical model based on a spectral analysis method. The model validation focusses on diffraction predictions and involves convergence tests and numerical comparisons with independent potential flow computations. Predictions of both regular and irregular wave responses are also compared against experimental results. Sample results including the yearly-averaged power conversion efficiency are presented in the final section to illustrate the method’s suitability to a 3D hydrodynamic design optimisation.     

Comparison of LIMPET contra-rotating wells turbine with theoretical and model test predictions

The performance of the contra-rotating Wells turbine installed in the LIMPET wave power station is compared to the predicted performance from theoretical analysis and model tests. A reasonable agreement was found between the predicted and measured turbine damping characteristic, however the turbine efficiency was found to be poorly predicted. It is postulated that this is due to the unsteady nature and mal-distribution of flow through the LIMPET turbine, which were not considered in the predictions. It is suggested that the reduced performance of the contra-rotating Wells turbine makes biplane or monoplane Wells turbines with guide vanes better solutions for OWC's.     

Experimental hydrodynamic investigation of a fixed offshore Oscillating Water Column device

Oscillating Water Column (OWC) is one of the pioneer devices in harnessing wave energy; however, it is not fully commercialized perhaps due to the complicated hydrodynamic behavior. Previous studies are significantly devoted to OWC devices located in nearshore and coastal regions where incident wave energy would experience dissipation more than offshore. In this paper, a 1:15 scaled fixed offshore OWC model is tested in a large towing tank of National Iranian Marine Laboratory. Wave spectrum shape effect on the efficiency of the OWC model is addressed. Moreover, the paper investigates the effects of the geometric and hydrodynamic factors on OWC device efficiency and uncovers new points in nonlinear interaction occurring inside the chamber; i.e. sloshing. The results indicate that shape of the spectrum inside the chamber is affected by the type of incident wave spectrum, especially for long waves. Pierson–Moskowitz spectrum leaded to higher efficiency rather than JONSWAP spectrum at longer incident wave periods. According to efficiency analysis, increasing wave height may lead to air leakage from the chamber followed by vortex generation, which is a reason for decreasing the efficiency of the OWC device. Furthermore, no shift in the resonant period of the OWC model, due to wave height increase, was observed at the opening ratios equal or smaller than 1.28%. Spectral analysis of water fluctuation inside the OWC chamber illustrates two modes of sloshing. The first mode can be seen at short period waves while the second mode is visible at long period waves. The sloshing modes approximately vanish by increasing draft value.     

半球形多向波聚合波道振荡水柱气室优化设计

为了解决振动水柱式波浪能转换装置收集多向波浪问题,本文设计了半球形多向聚合波道振荡水柱气室结构,以适合远海单点波浪能采集和发电。在规则波正向入射条件下,基于流体仿真分析软件(FLUENT)、流体动力学连续性假设和粘性不可压缩流体动量守恒的运动方程(Navier-Stokes方程)建立半球形振荡气室和三维数值波浪水槽模型。仿真结果表明:增设气室后壁,合理设计波道开口角度实现多向迎波捕获波浪能,优化前壁形状可降低波浪触底反射带来的能量耗散,同时提高了气室内空气压强和出气口速度,有效提升波浪能俘获效率,为后续发电的二次能量转换提供高效的空气动力。