Distributed modelling of future changes in hydrological processes of Spencer Creek watershed

The hydrologic impact of climate change has been largely assessed using mostly conceptual hydrologic models. This study investigates the use of distributed hydrologic model for the assessment of the climate change impact for the Spencer Creek watershed in Southern Ontario (Canada). A coupled MIKE SHE/MIKE 11 hydrologic model is developed to represent the complex hydrologic conditions in the Spencer Creek watershed, and later to simulate climate change impact using Canadian global climate model (CGCM 3·1) simulations. Owing to the coarse resolution of GCM data (daily GCM outputs), statistical downscaling techniques are used to generate higher resolution data (daily precipitation and temperature series). The modelling results show that the coupled model captured the snow storage well and also provided good simulation of evapotranspiration (ET) and groundwater recharge. The simulated streamflows are consistent with the observed flows at different sites within the catchment. Using a conservative climate change scenario, the downscaled GCM scenarios predicted an approximately 14–17% increase in the annual mean precipitation and 2–3 °C increase in annual mean maximum and minimum temperatures for the 2050s (i.e., 2046–2065). When the downscaled GCM scenarios were used in the coupled model, the model predicted a 1–5% annual decrease in snow storage for 2050s, approximately 1–10% increase in annual ET, and a 0·5–6% decrease in the annual groundwater recharge. These results are consistent with the downscaled temperature results. For future streamflows, the coupled model indicated an approximately 10–25% increase in annual streamflows for all sites, which is consistent with the predicted changes in precipitation. Overall, it is shown that distributed hydrologic modelling can provide useful information not only about future changes in streamflow but also changes in other key hydrologic processes such as snow storage, ET, and groundwater recharge, which can be particularly important depending on the climatic region of concern. The study results indicate that the coupled MIKE SHE/MIKE 11 hydrologic model could be a particularly useful tool for understanding the integrated effect of climate change in complex catchment scale hydrology. Copyright © 2010 John Wiley & Sons, Ltd.     

The integrated effects of climate and hydrologic uncertainty on future flood risk assessments

This work examines future flood risk within the context of integrated climate and hydrologic modelling uncertainty. The research questions investigated are (1) whether hydrologic uncertainties are a significant source of uncertainty relative to other sources such as climate variability and change and (2) whether a statistical characterization of uncertainty from a lumped, conceptual hydrologic model is sufficient to account for hydrologic uncertainties in the modelling process. To investigate these questions, an ensemble of climate simulations are propagated through hydrologic models and then through a reservoir simulation model to delimit the range of flood protection under a wide array of climate conditions. Uncertainty in mean climate changes and internal climate variability are framed using a risk‐based methodology and are explored using a stochastic weather generator. To account for hydrologic uncertainty, two hydrologic models are considered, a conceptual, lumped parameter model and a distributed, physically based model. In the conceptual model, parameter and residual error uncertainties are quantified and propagated through the analysis using a Bayesian modelling framework. The approach is demonstrated in a case study for the Coralville Dam on the Iowa River, where recent, intense flooding has raised questions about potential impacts of climate change on flood protection adequacy. Results indicate that the uncertainty surrounding future flood risk from hydrologic modelling and internal climate variability can be of the same order of magnitude as climate change. Furthermore, statistical uncertainty in the conceptual hydrological model can capture the primary structural differences that emerge in flood damage estimates between the two hydrologic models. Copyright © 2014 John Wiley & Sons, Ltd.     

Assessment of future precipitation indices in the Shikoku region using a statistical downscaling model

In this study, we used the statistical downscaling model (SDSM) to estimate mean and extreme precipitation indices under present and future climate conditions for Shikoku, Japan. Specifically, we considered the following mean and extreme precipitation indices: mean daily precipitation, R10 (number of days with precipitation >10 mm/day), R5d (annual maximum precipitation accumulated over 5 days), maximum dry-spell length (MaDSL), and maximum wet-spell length (MaWSL). Initially, we calibrated the SDSM model using the National Center for environmental prediction (NCEP) reanalysis dataset and daily time series of precipitation for ten locations in Shikoku which were acquired from the surface weather observation point dataset. Subsequently, we used the validated SDSM, using data from NCEP and outputs form general circulation models (GCM), to predict future precipitation indices. Specifically, the HadCM3 GCM was run under the special report on emissions scenarios (SRES) A2 and B2 scenarios, and the CGCM3 GCM was run under the SRES A2 and A1B scenarios. The results showed that: (1) the SDSM can reasonably be used to simulate mean and extreme precipitation indices in the Shikoku region; (2) the values of annual R10 were predicated to decrease in the future in northern Shikoku under all climate scenarios; conversely, the values of annual R10 were predicted to increase in the future in the range of 0–15 % in southern and western Shikoku. The values of annual MaDSL were predicted to increase in northern Shikoku, and the values of annual MaWSL were predicted to decrease in northeastern Shikoku; (3) the spatial variation of precipitation indices indicated the potential for an increased occurrence of drought across northeastern Shikoku and an increased occurrence of flood events in the southwestern part of Shikoku, especially under the A2 and A1B scenarios; (4) characteristics of future precipitation may differ between the northern and southern sides of the Shikoku Mountains. Regional variations in extreme precipitation indices were not notably evident in the B2 scenario compared to the other scenarios.     

A critical analysis of the cumulative rainfall departure concept

Evaluation of trends in time-series, such as precipitation or ground water levels, is an essential element in many hydrologic evaluations, including water resource studies and planning efforts. The cumulative rainfall departure (CRD) from normal rainfall is a concept sometimes utilized to evaluate the temporal correlation of rainfall with surface water or ground water levels. Permutations of the concept have been used to estimate recharge or aquifer storativity, and in attempts to explain declining ground water levels. The cumulative departure concept has hydrologic meaning in the short term, as a generalized evaluation of either meager or abundant rainfall, and when utilized in connection with a detailed water budget analysis can be used in a predictive fashion. However, the concept can be misapplied if extended over lengthy periods. Misapplication occurs because of several factors including the separation of the mean and median in nonnormal distributions, how the choice of beginning and end points of the data can affect the results, the lack of consideration that above-average rainfall can reset the hydrologic system without mathematically eliminating the accumulated deficit, and the lack of support for the necessary inference that rainfall events and hydrologic levels widely separated in time are linked. Standard statistical techniques are available to reliably determine trends and can provide rigorous statistical measures of the significance of conclusions. Misuse of the CRD concept can lead to erroneous and unsupported conclusions regarding hydrologic relationships and can potentially result in misguided water resource decision-making.     

Evaluation of global optimization algorithms for parameter calibration of a computationally intensive hydrologic model

With the popularity of complex hydrologic models, the time taken to run these models is increasing substantially. Comparing and evaluating the efficacy of different optimization algorithms for calibrating computationally intensive hydrologic models is becoming a nontrivial issue. In this study, five global optimization algorithms (genetic algorithms, shuffled complex evolution, particle swarm optimization, differential evolution, and artificial immune system) were tested for automatic parameter calibration of a complex hydrologic model, Soil and Water Assessment Tool (SWAT), in four watersheds. The results show that genetic algorithms (GA) outperform the other four algorithms given model evaluation numbers larger than 2000, while particle swarm optimization (PSO) can obtain better parameter solutions than other algorithms given fewer number of model runs (less than 2000). Given limited computational time, the PSO algorithm is preferred, while GA should be chosen given plenty of computational resources. When applying GA and PSO for parameter optimization of SWAT, small population size should be chosen. Copyright © 2008 John Wiley & Sons, Ltd.     

The use of geometric and gamma-related distributions for frequency analysis of water deficit

This paper presents an approach to perform statistical frequency analysis of water deficit duration and severity using respectively the geometric and exponential distributions. Monthly mean water discharges are compared to a given threshold and classified in two mutually exclusive ways. This leads to a two state random variable such that: a success represents the absence of a water deficit event (mean monthly discharge exceeds threshold), and a failure, a water deficit event (mean monthly discharge is below threshold). If we suppose that this random variable gives rise to a Markov process of order 1, then the duration of a water deficit event X (consecutive months in deficit) will have a geometric distribution. In turn, the summation of discharges in deficit will give the severity of a water deficit event which can be represented by a one-parameter exponential distribution. The threshold or base level is taken as a percentile of the observed mean discharges of a given month. This base level, which varies from month to month, can be viewed as the limit of an acceptable deficit (or energetic failure) associated to a given empirical probability of being in deficit. The second step of the approach is to estimate the value of the parameter for each distribution using the maximum likelihood method. Expressions for the estimator of a given percentile, , as well as its variance are deduced. Finally, the presented models are applied to observed data.     

Assessing the uncertainties of hydrologic model selection in climate change impact studies

The uncertainties associated with atmosphere‐ocean General Circulation Models (GCMs) and hydrologic models are assessed by means of multi‐modelling and using the statistically downscaled outputs from eight GCM simulations and two emission scenarios. The statistically downscaled atmospheric forcing is used to drive four hydrologic models, three lumped and one distributed, of differing complexity: the Sacramento Soil Moisture Accounting (SAC‐SMA) model, Conceptual HYdrologic MODel (HYMOD), Thornthwaite‐Mather model (TM) and the Precipitation Runoff Modelling System (PRMS). The models are calibrated based on three objective functions to create more plausible models for the study. The hydrologic model simulations are then combined using the Bayesian Model Averaging (BMA) method according to the performance of each models in the observed period, and the total variance of the models. The study is conducted over the rainfall‐dominated Tualatin River Basin (TRB) in Oregon, USA. This study shows that the hydrologic model uncertainty is considerably smaller than GCM uncertainty, except during the dry season, suggesting that the hydrologic model selection‐combination is critical when assessing the hydrologic climate change impact. The implementation of the BMA in analysing the ensemble results is found to be useful in integrating the projected runoff estimations from different models, while enabling to assess the model structural uncertainty. Copyright © 2011 John Wiley & Sons, Ltd.     

Spatially distributed long‐term hydrologic simulation using a continuous SCS CN method‐based hybrid hydrologic model

A continuous Soil Conservation Service (SCS) curve number (CN) method that considers time‐varied SCS CN values was developed based on the original SCS CN method with a revised soil moisture accounting approach to estimate run‐off depth for long‐term discontinuous storm events. The method was applied to spatially distributed long‐term hydrologic simulation of rainfall‐run‐off flow with an underlying assumption for its spatial variability using a geographic information systems‐based spatially distributed Clark's unit hydrograph method (Distributed‐Clark; hybrid hydrologic model), which is a simple few parameter run‐off routing method for input of spatiotemporally varied run‐off depth, incorporating conditional unit hydrograph adoption for different run‐off precipitation depth‐based direct run‐off flow convolution. Case studies of spatially distributed long‐term (total of 6 years) hydrologic simulation for four river basins using daily NEXRAD quantitative precipitation estimations demonstrate overall performances of Nash–Sutcliffe efficiency (E_NS) 0.62, coefficient of determination (R²) 0.64, and percent bias 0.33% in direct run‐off and E_NS 0.71, R² 0.72, and percent bias 0.15% in total streamflow for model result comparison against observed streamflow. These results show better fit (improvement in E_NS of 42.0% and R² of 33.3% for total streamflow) than the same model using spatially averaged gauged rainfall. Incorporation of logic for conditional initial abstraction in a continuous SCS CN method, which can accommodate initial run‐off loss amounts based on previous rainfall, slightly enhances model simulation performance; both E_NS and R² increased by 1.4% for total streamflow in a 4‐year calibration period. A continuous SCS CN method‐based hybrid hydrologic model presented in this study is, therefore, potentially significant to improved implementation of long‐term hydrologic applications for spatially distributed rainfall‐run‐off generation and routing, as a relatively simple hydrologic modelling approach for the use of more reliable gridded types of quantitative precipitation estimations.     

Understanding the role of hydrologic model structures on evapotranspiration-driven sensitivity

ABSTRACT

Most conceptual hydrological models do not treat vegetation as a dynamic component. This study focuses on understanding the impact of model structural complexity on the sensitivity of hydrologic models to potential evapotranspiration forcing data. To achieve this, two classes of hydrologic models are examined: (1) lumped, conceptual rainfall–runoff models and (2) eco-hydrologic models. A sample of 57 US catchments, covering eight eco-regions, included in the MOPEX dataset is used. While streamflow simulation performance in complex models did not exhibit increased sensitivity to PET, actual evapotranspiration simulation performance showed greater sensitivity in energy-limited catchments. This analysis warns against using over-simplistic PET estimations in energy-limited catchments for eco-hydrologic models and for more complex conceptual hydrologic models. This is particularly true for streamflow-only calibrations that commonly fail to properly constrain physically based parameters. Ultimately, these results have the potential to inform data collection and model selection efforts to yield the greatest benefit.     

Development of a soil moisture‐based distributed hydrologic model for determining hydrologically based critical source areas

A simple grid cell‐based distributed hydrologic model was developed to provide spatial information on hydrologic components for determining hydrologically based critical source areas. The model represents the critical process (soil moisture variation) to run‐off generation accounting for both local and global water balance. In this way, it simulates both infiltration excess run‐off and saturation excess run‐off. The model was tested by multisite and multivariable evaluation on the 50‐km² Little River Experimental Watershed I in Georgia, U.S. and 2 smaller nested subwatersheds. Water balance, hydrograph, and soil moisture were simulated and compared to observed data. For streamflow calibration, the daily Nash‐Sutcliffe coefficient was 0.78 at the watershed outlet and 0.56 and 0.75 at the 2 nested subwatersheds. For the validation period, the Nash‐Sutcliffe coefficients were 0.79 at the watershed outlet and 0.85 and 0.83 at the 2 subwatersheds. The per cent bias was less than 15% for all sites. For soil moisture, the model also predicted the rising and declining trends at 4 of the 5 measurement sites. The spatial distribution of surface run‐off simulated by the model was mainly controlled by local characteristics (precipitation, soil properties, and land cover) on dry days and by global watershed characteristics (relative position within the watershed and hydrologic connectivity) on wet days when saturation excess run‐off was simulated. The spatial details of run‐off generation and travel time along flow paths provided by the model are helpful for watershed managers to further identify critical source areas of non‐point source pollution and develop best management practices.     

Hydrological footprints of urban developments in the Lake Simcoe watershed,Canada: a combined paired‐catchment and change detection modelling approach

Urban sprawl and regional climate variability are major stresses on surface water resources in many places. The Lake Simcoe watershed (LSW) Ontario, Canada, is no exception. The LSW is predominantly agricultural but is experiencing rapid population growth because of its proximity to the Greater Toronto area. This has led to extensive land use changes that have impacted its water resources and altered run‐off patterns in some rivers draining to the lake. Here, we use a paired‐catchment approach, hydrological change detection modelling and remote sensing analysis of satellite images to evaluate the impacts of land use change on the hydrology of the LSW (1994 to 2008). Results show that urbanization increased up to 16% in Lovers Creek, the most urban‐impacted catchment. Annual run‐off from Lovers Creek increased from 239 to 442 mm/year in contrast to the reference catchment (Black River at Washago) where run‐off was relatively stable with an annual mean of 474 mm/year. Increased annual run‐off from Lovers Creek was not accompanied by an increase in annual precipitation. Discriminant function analysis suggests that early (1992–1997; pre‐major development) and late (2004–2009; fully urbanized) periods for Lovers Creek separated mainly based on model parameter sets related to run‐off flashiness and evapotranspiration. As a result, parameterization in either period cannot be used interchangeably to produce credible run‐off simulations in Lovers Creek because of greater scatter between the parameters in canonical space. Separation of early and late‐period parameter sets for the reference catchment was based on climate and snowmelt‐related processes. This suggests that regional climatic variability could be influencing hydrologic change in the reference catchment, whereas urbanization amplified the regional natural hydrologic changes in urbanizing catchments of the LSW. Copyright © 2014 John Wiley & Sons, Ltd.     

Compared performance of a conceptual and a mechanistic hydrologic models of a green roof

In order to investigate the hydrologic response of a green roof system within the urban environment, a monitoring campaign is carried out at the green roof site of the University of Genova (Italy). Experimental data confirm that the green roof is able to significantly mitigate the generation of runoff with median values of retained volume and peak reduction, respectively, equal to 94 and 98%. A conceptual linear reservoir and a simple mechanistic (Hydrus‐1D) models are implemented to simulate the hydrologic behaviour of the system; each model is calibrated and validated based on experimental data collected at the green roof site. The hydrographs simulated with both hydrologic models reproduce with acceptable matching capabilities the experimental measurements, as confirmed by the Nash‐Sutcliffe Efficiency index generally greater than 0·60. Although the relative percentage differences evaluated for the selected hydrograph variables (the total effluent volume, the peak flow rate and the hydrograph centroid) demonstrate that the mechanistic model is more accurate, prediction errors of the conceptual model are generally limited when compared with the observed hydrologic performance. Results of the present comparison are useful in supporting conceptual model selection in case the hydrologic response is addressed for hydrologic performance assessment. Copyright © 2011 John Wiley & Sons, Ltd.     

Comparison of storm surge/tide predictions between a 2-D operational forecast system, the regional tide/storm surge model (RTSM), and the 3-D regional ocean modeling system (ROMS)

In this study, we compare simulated storm surges run on the two-dimensional operational storm surge/tide forecast system (regional tide/storm surge model (RTSM), based on Princeton ocean model) of the Korean Meteorological Administration and the three-dimensional regional ocean modeling system (ROMS), using observational data from 30 coastal tidal stations of three typhoons that struck Korea in 2007. A maximum positive bias of 6.8 cm was found for Typhoon Manyi predicted by ROMS, while a maximum negative bias of −7.4 cm was shown for Typhoon Nari predicted by RTSM. For all three typhoons, the total averaged root mean square error was 10 cm for the two models. Although the statistical results for the storm surge comparison between the observations and RTSM predictions were better than those for ROMS, with the exception of Typhoon Nari, the spatial and temporal variations of ROMS were larger than those of RTSM.     

On the use of multi‐algorithm,genetically adaptive multi‐objective method for multi‐site calibration of the SWAT model

With the availability of spatially distributed data, distributed hydrologic models are increasingly used for simulation of spatially varied hydrologic processes to understand and manage natural and human activities that affect watershed systems. Multi‐objective optimization methods have been applied to calibrate distributed hydrologic models using observed data from multiple sites. As the time consumed by running these complex models is increasing substantially, selecting efficient and effective multi‐objective optimization algorithms is becoming a nontrivial issue. In this study, we evaluated a multi‐algorithm, genetically adaptive multi‐objective method (AMALGAM) for multi‐site calibration of a distributed hydrologic model—Soil and Water Assessment Tool (SWAT), and compared its performance with two widely used evolutionary multi‐objective optimization (EMO) algorithms (i.e. Strength Pareto Evolutionary Algorithm 2 (SPEA2) and Non‐dominated Sorted Genetic Algorithm II (NSGA‐II)). In order to provide insights into each method's overall performance, these three methods were tested in four watersheds with various characteristics. The test results indicate that the AMALGAM can consistently provide competitive or superior results compared with the other two methods. The multi‐method search framework of AMALGAM, which can flexibly and adaptively utilize multiple optimization algorithms, makes it a promising tool for multi‐site calibration of the distributed SWAT. For practical use of AMALGAM, it is suggested to implement this method in multiple trials with relatively small number of model runs rather than run it once with long iterations. In addition, incorporating different multi‐objective optimization algorithms and multi‐mode search operators into AMALGAM deserves further research. Copyright © 2009 John Wiley & Sons, Ltd.     

Wetlandscape hydrologic dynamics driven by shallow groundwater and landscape topography

Wetlands play an important role in watershed eco-hydrology. The occurrence and distribution of wetlands in a landscape are affected by the surface topography and the hydro-climatic conditions. Here, we propose a minimalist probabilistic approach to describe the dynamic behaviour of wetlandscape attributes, including number of inundated wetlands and the statistical properties of wetland stage, surface area, perimeter, and storage volume. The method relies on two major assumptions: (a) wetland bottom hydrologic resistance is negligible; and (b) groundwater level is parallel to the mean terrain elevation. The approach links the number of inundated wetlands (depressions with water) to the distribution of wetland bottoms and divides, and the position of the shallow water table. We compared the wetlandscape attribute dynamics estimated from the probabilistic approach to those determined from a parsimonious hydrologic model for groundwater-dominated wetlands. We test the reliability of the assumptions of both models using data from six cypress dome wetlands in the Green Swamp Wildlife Management Area, Florida. The results of the hydrologic model for groundwater-dominated wetlands showed that the number of inundated wetlands has a unimodal dependence on the groundwater level, as predicted by the probabilistic approach. The proposed models provide a quantitative basis to understand the physical processes that drive the spatiotemporal hydrologic dynamics in wetlandscapes impacted by shallow groundwater fluctuations. Emergent patterns in wetlandscape hydrologic dynamics are of key importance not only for the conservation of water resources, but also for a wide range of eco-hydrological services provided by connectivity between wetlands and their surrounding uplands.     

On the effects of triangulated terrain resolution on distributed hydrologic model response

Distributed hydrologic models based on triangulated irregular networks (TIN) provide a means for computational efficiency in small to large‐scale watershed modelling through an adaptive, multiple resolution representation of complex basin topography. Despite previous research with TIN‐based hydrology models, the effect of triangulated terrain resolution on basin hydrologic response has received surprisingly little attention. Evaluating the impact of adaptive gridding on hydrologic response is important for determining the level of detail required in a terrain model. In this study, we address the spatial sensitivity of the TIN‐based Real‐time Integrated Basin Simulator (tRIBS) in order to assess the variability in the basin‐averaged and distributed hydrologic response (water balance, runoff mechanisms, surface saturation, groundwater dynamics) with respect to changes in topographic resolution. Prior to hydrologic simulations, we describe the generation of TIN models that effectively capture topographic and hydrographic variability from grid digital elevation models. In addition, we discuss the sampling methods and performance metrics utilized in the spatial aggregation of triangulated terrain models. For a 64 km² catchment in northeastern Oklahoma, we conduct a multiple resolution validation experiment by utilizing the tRIBS model over a wide range of spatial aggregation levels. Hydrologic performance is assessed as a function of the terrain resolution, with the variability in basin response attributed to variations in the coupled surface–subsurface dynamics. In particular, resolving the near‐stream, variable source area is found to be a key determinant of model behaviour as it controls the dynamic saturation pattern and its effect on rainfall partitioning. A relationship between the hydrologic sensitivity to resolution and the spatial aggregation of terrain attributes is presented as an effective means for selecting the model resolution. Finally, the study highlights the important effects of terrain resolution on distributed hydrologic model response and provides insight into the multiple resolution calibration and validation of TIN‐based hydrology models. Copyright © 2005 John Wiley & Sons, Ltd.     

Spatial interpolation schemes of daily precipitation for hydrologic modeling

Distributed hydrologic models typically require spatial estimates of precipitation interpolated from sparsely located observational points to the specific grid points. We compare and contrast the performance of regression-based statistical methods for the spatial estimation of precipitation in two hydrologically different basins and confirmed that widely used regression-based estimation schemes fail to describe the realistic spatial variability of daily precipitation field. The methods assessed are: (1) inverse distance weighted average; (2) multiple linear regression (MLR); (3) climatological MLR; and (4) locally weighted polynomial regression (LWP). In order to improve the performance of the interpolations, the authors propose a two-step regression technique for effective daily precipitation estimation. In this simple two-step estimation process, precipitation occurrence is first generated via a logistic regression model before estimate the amount of precipitation separately on wet days. This process generated the precipitation occurrence, amount, and spatial correlation effectively. A distributed hydrologic model (PRMS) was used for the impact analysis in daily time step simulation. Multiple simulations suggested noticeable differences between the input alternatives generated by three different interpolation schemes. Differences are shown in overall simulation error against the observations, degree of explained variability, and seasonal volumes. Simulated streamflows also showed different characteristics in mean, maximum, minimum, and peak flows. Given the same parameter optimization technique, LWP input showed least streamflow error in Alapaha basin and CMLR input showed least error (still very close to LWP) in Animas basin. All of the two-step interpolation inputs resulted in lower streamflow error compared to the directly interpolated inputs.     

On the prediction of the Toce alpine basin floods with distributed hydrologic models

With the objective of improving flood predictions, in recent years sophisticated continuous hydrologic models that include complex land‐surface sub‐models have been developed. This has produced a significant increase in parameterization; consequently, applications of distributed models to ungauged basins lacking specific data from field campaigns may become redundant. The objective of this paper is to produce a parsimonious and robust distributed hydrologic model for flood predictions in Italian alpine basins. Application is made to the Toce basin (area 1534 km²). The Toce basin was a case study of the RAPHAEL European Union research project, during which a comprehensive set of hydrologic, meteorological and physiographic data were collected, including the hydrologic analysis of the 1996–1997 period. Two major floods occurred during this period. We compare the FEST04 event model (which computes rainfall abstraction and antecedent soil moisture conditions through the simple Soil Conservation Service curve number method) and two continuous hydrologic models, SDM and TDM (which differ in soil water balance scheme, and base flow and runoff generation computations). The simple FEST04 event model demonstrated good performance in the prediction of the 1997 flood, but shows limits in the prediction of the long and moderate 1996 flood. More robust predictions are obtained with the parsimonious SDM continuous hydrologic model, which uses a simple one‐layer soil water balance model and an infiltration excess mechanism for runoff generation, and demonstrates good performance in both long‐term runoff modelling and flood predictions. Instead, the use of a more sophisticated continuous hydrologic model, the TDM, that simulates soil moisture dynamics in two layers of soil, and computes runoff and base flow using some TOPMODEL concepts, does not seem to be advantageous for this alpine basin. Copyright © 2006 John Wiley & Sons, Ltd.     

Understanding the water balance paradox in the Athabasca River Basin,Canada

This study demonstrates the importance of the including and appropriately parameterizing peatlands and forestlands for basin‐scale integrated surface–subsurface models in the northern boreal forest, with particular emphasis on the Athabasca River Basin (ARB). With a long‐term water balance approach to the ARB, we investigate reasons why downstream mean annual stream flow rates are consistently higher than upstream, despite the subhumid water deficit conditions in the downstream regimes. A high‐resolution 3D variably saturated subsurface and surface water flow and evapotranspiration model of the ARB is constructed based on the bedrock and surficial geology and the spatial distribution of peatlands and their corresponding eco‐regions. Historical climate data were used to drive the model for calibration against 40‐year long‐term average surface flow and groundwater observations during the historic instrumental period. The simulation results demonstrate that at the basin‐scale, peatlands and forestlands can have a strong influence on the surface–subsurface hydrologic systems. In particular, peatlands in the midstream and downstream regimes of the ARB increase the water availability to the surface–subsurface water systems by reducing water loss through evapotranspiration. Based on the comparison of forestland evapotranspiration between observation and simulation, the overall spatial average evapotranspiration in downstream forestlands is larger than that in peatlands and thus the water contribution to the stream flow in downstream areas is relatively minor. Therefore, appropriate representation of peatlands and forestlands within the basin‐scale hydrologic model is critical to reproduce the water balance of the ARB.