渤海海域黏性土剪切波速与抗剪强度统计关系的初步研究

剪切波速与地基土的抗剪强度、剪切模量和卓越周期等参数密切相关,是地震安全性评价中判定场地类别的一个主要指标和参数。鉴于海域工程中剪切波速往往难以直接由原位测得,而室内实验结果又常常与野外现场物探测试值存在较大差异,因此,如何通过其他途径有效获取满足工程需要的剪切波速参数在海域工程的地震安全性评价等方面具有迫切的实用需求。为此本文通过对渤海海域数十个石油平台项目中一系列饱和黏性土样品的剪切波速与抗剪强度实验数据的统计分析,尝试采用多种可能的函数来拟合确定二者之间的经验关系。结果表明:对于渤海海域黏性土剪切波速V_s与抗剪强度S_u之间的最佳统计经验关系为幂函数V_s=53.751S_u~(0.376)。此关系可为渤海海域工程中通过不排水抗剪强度估算剪切波速提供一种简便可行的实用性方法。     

Probabilistic development of shear strength model for reinforced concrete squat walls

In order to reconcile the larger scatter and avoid the biased estimate from deterministic predictions for the shear strength of reinforced concrete (RC) squat structural walls, a probabilistic shear strength model is developed in this paper based on the strut‐and‐tie model and the generalized likelihood uncertainty estimation (GLUE) method. The strut‐and‐tie model is used to derive an appropriate function form for the probabilistic shear strength model, where four unknown model parameters (e.g. k₁, k₂, k₃ and k₄) are defined carefully to guarantee them having a clear physical‐based meaning so that the corresponding prior distribution ranges can be specified reasonably. Then, the GLUE method is adopted to estimate the posterior cumulative distribution of k₁, k₂, k₃ and k₄ with an available experimental database. Furthermore, to demonstrate the stability of the estimated posterior cumulative distribution, the sensitivity of three major aspects in GLUE method is investigated. Finally, based on the estimated cumulative distribution of k₁, k₂, k₃ and k₄, the developed probabilistic shear strength model is simplified as a mean prediction model and a standard deviation prediction model for facilitate using in engineering practice. Therefore, with the developed probabilistic shear strength model, not only can the squat structural walls be designed in confidence, but the accuracy of those deterministic predictions can be evaluated in a probabilistic manner. Copyright © 2016 John Wiley & Sons, Ltd.     

Postcyclic behavior of low-plasticity silt with limited excess pore pressures

This paper investigates the postcyclic behavior of low-plasticity silt with excess pore pressure ratio (R_u) less than 1. The testing specimens were prepared from Mississippi River Valley (MRV) silt. Full and no reconsolidation were allowed after specimens were subjected to various excess pore pressure ratios due to cyclic loading in a cyclic triaxial cell, and then monotonic shear tests were conducted. The effect of the R_u on shear strength and stiffness at small and large deformation was investigated. It was found that a R_u greater than 0.70 is a prerequisite of large increase in volumetric strain and undrained shear strength for specimens with full reconsolidation. In contrast, a significant decrease in yield shear strength and initial stiffness was noted for specimens without reconsolidation. In comparison to published data for sands, the silt experienced significant volumetric strain due to reconsolidation at lower R_u, indicating that the specimen fabric was modified or strained at lower R_u.     

Erodibility of cohesive streambeds in the loess area of the midwestern USA

Excess stress parameters, critical shear stress (τ_c) and erodibility coefficient (k_d), for degrading channels in the loess areas of the midwestern USA are presented based on in situ jet‐testing measurements. Critical shear stress and k_d are used to define the erosion resistance of the streambed. The jet‐testing apparatus applies hydraulic stresses to the bed and the resulting scour due to the impinging jet is related to the excess stress parameters. Streams tested were primarily silt‐bedded in texture with low densities, which is typical of loess soils. Results indicate that there is a wide variation in the erosion resistance of streambeds, spanning six orders of magnitude for τ_c and four orders of magnitude for k_d. Erosion resistance was observed to vary within a streambed, from streambed to streambed, and from region to region. An example of the diversity of materials within a river system is the Yalobusha River Basin in Mississippi. The median value of τ_c for the two primary bed materials, Naheola and Porters Creek Clay Formations, was 1·31 and 256 Pa, respectively. Streambeds composed of the Naheola Formation are readily eroded over the entire range of shear stresses, whereas only the deepest flows generate boundary stresses great enough to erode streambeds composed of the Porters Creek Clay Formation. Therefore, assessing material resistance and location is essential in classifying and modelling streambed erosion processes of these streams.     

On the seismic phasesP n andS n as recorded in Fennoscandia

Summary P _n velocities determined from seismic refraction measurements, show significant differences between Southern Finland (7.96 km/sec) and Southeastern Norway (8.20 km/sec). TheP _n/S_n velocity ratios (k) were determined from earthquake and explosion data, and the observed variation ofk indicates lateral variations in theP _n and/orS _n velocities in Fennoscandia.     

A robust empirical model to estimate earthquake-induced excess pore water pressure in saturated and non-saturated soils

In engineering practice, the liquefaction potential of a sandy soil is usually evaluated with a semi-empirical, stress-based approach computing a factor of safety in free field conditions, defined as the ratio between the liquefaction resistance (capacity) and the seismic demand. By so doing, an estimate of liquefaction potential is obtained, but nothing is known on the pore pressure increments (often expressed in the form of normalized pore pressure ratio r_u) generated by the seismic action when the safety factor is higher than 1. Even though r_u can be estimated using complex numerical analyses, it would be extremely useful to have a simplified procedure to estimate them consistent with the stress-based approach adopted to check the safety conditions. This paper proposes such a procedure with reference to both saturated and unsaturated soils, considering the latter as soils for which partial saturation has been artificially generated with some ground improvement technology to increase cyclic strength and thus tackle liquefaction risk. A simple relationship between the liquefaction free field safety factor FS, and r_u(S_r) is introduced, that generalizes a previous expression proposed by Chiaradonna and Flora (Geotech Lett, 2020. https://doi.org/10.1680/jgele.19.00032) for saturated soils. The new procedure has been successfully verified against some experimental data, coming from laboratory constant amplitude cyclic tests and from centrifuge tests with irregular acceleration time histories for soils having different gradings and densities.

     

Control algorithm for estimating future responses of active variable stiffness structure

A control algorithm has been developed for controlling Active Variable Stiffness (AVS) structures. This algorithm analyses information of an observed seismic excitation, estimates the future structural responses and determines how to alter the structure stiffness. An objective structure is assumed to possess N on-off elements whose states are controlled by the proposed algorithm. That is, at a given moment t_k, (1) seismic excitation information is expressed by an Auto Regressive (AR) model as the identification model; (2) future excitation information is predicted using the AR model; (3) future responses due to predicted excitation are estimated; (4) based on the initial condition at t_k, the responses of 2^N possible structural states from t_k, to t_k+L are calculated; (5) the state which minimizes the input energy during t_L is selected; and (6) immediately after t_k, on-off elements are set up and subjected to the selected states. The effectiveness of the induced algorithm is confirmed by numerical experiments on a model of a three-storey building under sine and seismic excitations.     

Evaluation of the seismic performance of a three‐story ordinary moment‐resisting concrete frame

This study focuses on the seismic performance of Ordinary Moment‐Resisting Concrete Frames (OMRCF) designed only for gravity loads. For this purpose, a 3‐story OMRCF was designed in compliance with the minimum design requirements in the American Concrete Institute Building Code ACI 318 (1999). This model frame was a regular structure with flexure‐dominated response. A 1/3‐scale 3‐story model was constructed and tested under quasi‐static reversed cyclic lateral loading. The overall behavior of the OMRCF was quite stable without abrupt strength degradation. The measured base shear strength was larger than the design base shear force for seismic zones 1, 2A and 2B calculated using UBC 1997. Moreover, this study used the capacity spectrum method to evaluate the seismic performance of the frame. The capacity curve was obtained from the experimental results for the specimen and the demand curve was established using the earthquake ground motions recorded at various stations with different soil conditions. Evaluation of the test results shows that the 3‐story OMRCF can resist design seismic loads of zones 1, 2A, 2B, 3 and 4 with soil types S_A and S_B . For soil type S_C , the specimen was satisfactory in seismic zones 1, 2A, 2B and 3. For soil type S_D , the OMRCF was only satisfactory for seismic zones 1 and 2A. Copyright © 2004 John Wiley & Sons, Ltd.     

Effect of consolidation ratios on maximum dynamic shear modulus of sands

The dynamic shear modulus (DSM) is the most basic soil parameter in earthquake or other dynamic loading conditions and can be obtained through testing in the field or in the laboratory. The effect of consolidation ratios on the maximum DSM for two types of sand is investigated by using resonant column tests. And, an increment formula to obtain the maximum DSM for cases of consolidation ratio κc>1 is presented. The results indicate that the maximum DSM rises rapidly when κc is near 1 and then slows down, which means that the power function of the consolidation ratio increment κc-1 can be used to describe the variation of the maximum DSM due to κc>1. The results also indicate that the increase in the maximum DSM due to κc>1 is significantly larger than that predicted by Hardin and Black's formula.     

云南地区GNSS应变场时空演化与地震事件关联分析

采用GAMIT/GLOBK软件对云南境内及邻区近400个GNSS测点1999～2018年的观测数据进行解算,在各个测点时间序列和速度场的基础上,采用克里金插值方法分时段估计该区域在1999～2004年、2004～2007年、2009～2013年、2013～2015年、2015～2018年共计5个时间区域应变率场;根据区域地壳面应变率和最大剪应变率的空间变化以及相应时段之后3年内的MS≥5. 0地震事件分布特征,分析发现:绝大部分震例发生在面应变高梯度带的张压转换区和最大剪应变高值区,可见研究区各个观测时段GNSS应变率场对后期1～3年内的中强震发生区域有一定的指示意义;以2014年盈江6. 1级、鲁甸6. 5级和景谷6. 6级地震为样本,建立监视块体获取应变时间序列,分析发现:地震前三个月左右均出现震中附近短期应变趋势改变、快速增强、转折的现象,这些形变异常变化或许反映了发震区应力-应变积累在接近临界破裂状态时的非线性调整,为地震短临预测尤其是时间要素的判断提供参考。     

Correlations Between Shear Wave Velocity and In-Situ Penetration Test Results for Korean Soil Deposits

Shear wave velocity (V _S) can be obtained using seismic tests, and is viewed as a fundamental geotechnical characteristic for seismic design and seismic performance evaluation in the field of earthquake engineering. To apply conventional geotechnical site investigation techniques to geotechnical earthquake engineering, standard penetration tests (SPT) and piezocone penetration tests (CPTu) were undertaken together with a variety of borehole seismic tests for a range of sites in Korea. Statistical modeling of the in-situ testing data identified correlations between V _S and geotechnical in-situ penetration data, such as blow counts (N value) from SPT and CPTu data including tip resistance (q _t), sleeve friction (f _s), and pore pressure ratio (B _q). Despite the difference in strain levels between conventional geotechnical penetration tests and borehole seismic tests, it is shown that the suggested correlations in this study is applicable to the preliminary determination of V _S for soil deposits.     

Evaluation of shear wave velocity profile using SPT based uphole method

The uphole method is a field seismic test which uses receivers on the ground surface and an underground source. A modified form of the uphole method is introduced in order to obtain efficiently the shear wave velocity (V_S) profile of a site. This method is called the standard penetration test (SPT)-uphole method because it uses the impact energy of the split spoon sampler in the SPT test as a source. Since the SPT-uphole method can be performed simultaneously with the SPT test it is economical and not labor intensive compared to the original uphole methods which use small explosives or a mechanical source. Field testing and interpretation procedures for the proposed method are described. To obtain reliable travel time information of the shear wave, the first peak point of the shear wave using two component geophones is recommended. Through a numerical study using the finite element method (FEM), the procedure of the proposed method was verified. Finally, the SPT-uphole method was performed at several sites, and the field applicability of the proposed method was verified by comparing the V_S profiles determined by the SPT-uphole method with the profiles determined by the downhole, the spectral analysis of surfaces waves (SASW) method and from the SPT-N values.     

Housner谱烈度的一种快速近似算法

Housner谱烈度及修正谱烈度作为基于加速度记录时程直接得到的地震动强度参数,与建筑结构破坏及地震宏观烈度存在较高的相关性,是可靠的地震仪器烈度物理参数指标。然而,相对于地面加速度峰值、地面速度峰值等地震动峰值参数,三分量加速度记录对应的谱烈度计算过程较为复杂,耗时相对较长,影响了利用谱烈度确定地震仪器烈度的时效性。基于对强震动加速度记录的统计分析,本文提出了谱烈度的快速近似算法,仅计算4个方向上的谱烈度值,采用其中3点作圆即可获得水平面内谱烈度迹线的近似最大值,使计算速度提高了45倍,且保持了谱烈度作为地震仪器烈度物理指标的精度。利用在汶川M_S 8.0地震等386次M_S > 3.0地震中获取的2701组强震动加速度记录,经可靠性检验,结果表明所提出的Housner谱烈度快速近似算法的计算误差在±4.5%以内,可以同时满足地震仪器烈度速报的可靠性和时效性需求。     

An extended theory of equi-risk line for a general release rule

The expression of equi-risk line derived by the authors represents the relationship between discharge capacityy ₀ ^u and storage capacityz ₀ ^u to keep flood frequency under a certain risk level represented by the return periodT, i.e.,z ₀/z ₀ ^u ={(y ₀ ^u –y ₀ ^u )/y ₀ ^u } ^S , wherey ₀ ^u andz ₀ ^u areT-year probability peak discharge and total volume of a hydrograph. The shape parametersS is evaluated in this paper for various release rules of the storage facilities and correlations of durations and peaks of hydrographs. The expression forS is: , whereS ₀ andS are the values ofS forp=0 and , andp is the exponent of a general storage-release relation,q=az' ^p, wherea is the storage constant, andz' andq are the volume of stored water and the corresponding release. The values ofS ₀ andS are expressed in terms of the correlation coefficient of durations and peaks of inflow hydrographs.     

澳门地区土层地震波速的测量结果

通过一系列野外及实验室试验,对澳门地区土层地震波速进行了初步测量,从初步的现场试验结果来看,浅层的地震波速受到堆填物料的影响颇大,变化显得较为宽广,随着深度的增加,由于天然土层较为均一,地震波速的变化亦见收窄,现场剪切波速数据与标准贯人试验（SPT）数据可见一定吻合性。而通过等向及异向固结的实验室试验,发现澳门海泥的剪切波速在同一平均有效应力而不同应力路径下大致相同,此外,比较野外及实验室试验结果,亦显示澳门海泥的剪切波速受土体天然结构影响不大。     

Seismic behavior and zoning of the sabkha soils in Jubail industrial city,Saudi Arabia

This study aimed at the micro-level seismic behavior and zoning of the saline sabkha strata in Jubail industrial area in Eastern Saudi Arabia. It encompasses the evaluation of the site-specific seismic response parameters and the liquefaction potential for various possible subsurface conditions under the probable seismic event(s). The approach to achieve the objectives of this study included the following: analysis of geologic, hydrologic, and geotechnical data of the area; performance of field and laboratory dynamic testing; and dynamic modeling and analysis of the subsurface profiles. The results of the simulation have been used to develop liquefaction potential maps and site-specific spectra of the study area, consisting of ten seismic zones under a range of probable peak horizontal ground acceleration (PHA). Results do not show significant probability of liquefaction of the loose soil layers in the study area at the maximum possible design PHA of 0.035 g; however, liquefaction is anticipated at higher PHA values. Site-specific spectral response resulted in values of S _s and S ₁ spectral accelerations to be different as compared to those suggested by local standards. The resulting seismic micro-zonation maps and the corresponding parameters are very useful for the stability analysis of the existing and planned structures in the Jubail area.     

Seismic response analysis of multidrum classical columns

This paper presents a numerical investigation on the seismic response of multidrum classical columns. The motivation for this study originates from the need to understand: (a) the level of ground shaking that classical multidrum columns can survive, and (b) the possible advantages or disadvantages of retrofitting multidrum columns with metallic shear links that replace the wooden poles that were installed in ancient times. The numerical study presented in this paper is conducted with the commercially available software Working Model 2D?, which can capture with fidelity the sliding, rocking, and slide‐rocking response of rigid‐body assemblies. This paper validates the software Working Model by comparing selected computed responses with scarce analytical solutions and the results from in‐house numerical codes initially developed at the University of California, Berkeley, to study the seismic response of electrical transformers and heavy laboratory equipment. The study reveals that relative sliding between drums happens even when the g‐value of the ground acceleration is less than the coefficient of friction, µ, of the sliding interfaces and concludes that: (a) typical multidrum classical columns can survive the ground shaking from strong ground motions recorded near the causative faults of earthquakes with magnitudes M_w=6.0–7.4; (b) in most cases multidrum classical columns free to dislocate at the drum interfaces exhibit more controlled seismic response than the monolithic columns with same size and slenderness; (c) the shear strength of the wooden poles has a marginal effect on the sliding response of the drums; and (d) stiff metallic shear links in‐between column drums may have an undesirable role on the seismic stability of classical columns and should be avoided. Copyright © 2005 John Wiley & Sons, Ltd.     

Cyclic shear response of channel-fill Fraser River Delta silt

The cyclic shear response of a channel-fill, low-plastic silt was investigated using constant-volume direct simple shear testing. Silt specimens, initially consolidated to stress levels at or above the preconsolidation stress, displayed cyclic-mobility-type strain development during cyclic loading without static shear stress bias. Liquefaction in the form of strain softening accompanied by loss of shear strength did not manifest regardless of the applied cyclic stress ratio, or the level of induced excess pore water pressure, suggesting that the silt is unlikely to experience flow failure under cyclic loading. The cyclic shear resistance of the silt increased with increasing overconsolidation ratio (OCR) for OCR>1.3. The silt specimens that experienced high equivalent excess cyclic pore water pressure ratios (r_u>80%) resulted in considerable volumetric strains (2.5%–5%) during post-cyclic reconsolidation implying potentially significant changes to the particle fabric under cyclic loading.